Windows 8.1 with Hyper-V external switch - 802.1x not working in host nor guest
Hi,
I have Windows 8.1 with installed Hyper-V and virtual machines connected via Hyper-V Switch - External. 802.1x wired authentication is not working in host nor in guest machine (computer is not responding to switch requests). If I will change switch mode
to Internal/Private it will start working.
Do you have any idea how to get it working also in external mode?
Hi,
What is the physical network configuration in your environment? Are you using wireless or wired connection?
We tested this issue as you described here, and the external switch is working fine.
Have you tried to delete the created switches and recreate one, test this issue again?
Yolanda Zhu
TechNet Community Support
Similar Messages
-
External USB HD does not work with HAL:
External USB HD does not work with HAL:
From the last 10 days the HAL auto-mount with ntfs-3g file system of my external hard drive does not woks.
But the manual mount procedure with the command mount -t ntfs-3g /dev/sdb* /mnt/XYZ works.
I've followed the instructions in the wiki: http://wiki.archlinux.org/index.php/HAL and the system has worked up to the last kernel or HAL update.
My fat32 usb-stick works without any problem.
If I try to open the device with KDE it appears an error popup wit this message:
TODO: have to rethink extra options
Error: kio_media_mount_helper
The log from the kernel.log is
Nov 6 22:03:16 myhost usb 5-1: new high speed USB device using ehci_hcd and address 4
Nov 6 22:03:16 myhost usb 5-1: configuration #1 chosen from 1 choice
Nov 6 22:03:17 myhost Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
Nov 6 22:03:17 myhost ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Nov 6 22:03:17 myhost Initializing USB Mass Storage driver...
Nov 6 22:03:17 myhost scsi6 : SCSI emulation for USB Mass Storage devices
Nov 6 22:03:17 myhost usb-storage: device found at 4
Nov 6 22:03:17 myhost usb-storage: waiting for device to settle before scanning
Nov 6 22:03:17 myhost usbcore: registered new interface driver usb-storage
Nov 6 22:03:17 myhost USB Mass Storage support registered.
Nov 6 22:03:22 myhost scsi 6:0:0:0: Direct-Access WDC WD32 00JB-00KFA0 0811 PQ: 0 ANSI: 0
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Test WP failed, assume Write Enabled
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] 625142448 512-byte hardware sectors (320073 MB)
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Test WP failed, assume Write Enabled
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 6 22:03:22 myhost sdb: sdb1
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Attached SCSI disk
Nov 6 22:03:22 myhost sd 6:0:0:0: Attached scsi generic sg2 type 0
Nov 6 22:03:22 myhost usb-storage: device scan complete
and the error.log is
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Nov 6 22:03:22 myhost sd 6:0:0:0: [sdb] Assuming drive cache: write through
Do you have some idea ....
Bye.I have done the following:
Downloaded the patched hal version.
used makepkg in /abs/local/trunk/ to create a pkg for pacman
used sudo pacman -U pkgname to install it.
used sudo nano /etc/hal/fdi/policy/preferences.fdi to create the fdi file with the following content:
saved the file and removed my ntfs entryes from fstab and rebooted. and still there is no automount off ntfs partitions.
have i done something wrong?
br fjodork
WARNING: what follows is a guide of what did work for me, I'm still in an early stage of learning linux, so please correct me if anything of what follows is wrong/dangerous/stupid. As I said, this worked for me, it's not pretty, since I was learning each step on the fly and I'm sure there are better ways to do this.
So fjodork, you seem to have done the the necessary steps, though i couldn't get it to work until i first removed hal without dependencies
pacman -Rd hal
it will give you some warning about the dependencies, ignore it since we are reinstalling hal in a few steps.
First i tried to follow Raymano's link, obviously it showed me nothing in the browser so I thought it might be a broken link.
So I downloaded the source tarball from here http://hal.freedesktop.org/releases/hal-0.5.10.tar.gz
unpacked it changed the /tools/hal-storage-mount.c as per Milfadoodle's instructions.
at first I tried to compile directly from source, the process would finish without a glitch though after reboot nothing changed, as if hal weren't
installed, i guess there were issues with paths. anyway read on
Then repacked the source in tarball, copied it to /var/abs/extra/system/hal and modified the PKGBUILD as follows
makedepends=('pkgconfig' 'gperf')
options=('!libtool')
install=hal.install
source=(${pkgname}-${pkgver}.tar.gz #removed url so makepkg looks in the current directory for the tarball
hal
hal-policy.patch
cryptsetup_location.patch
hal-0.5.9-hide-diagnostic.patch
ntfs3g-valid-options.patch)
md5sums=('6641c30a27c00485c6accac5110ff911' # replace with md5sum of your package's sourceball (run md5sum filename)
'882f67668cb14a0a9e4a27ef22278027'
'5ba8b610aa9763a5f42b9f7cbd7a86ad'
then makepkg (i had to add --asroot, don't ask why
and finally pacman -U hal-0.5.10-1-i686.pkg
another reboot and everything worked without a glitch!:D (yeah i know i still haven't got rid of the reboot mentality )
I have also put the policy files as per the wiki instructions.
PS: I know this is a dirty way to getting things done but as i said, I'm just starting
If anyone could comment/correct/explain this post I'd be more than happy, the automount issue was bothering me for about a month now (you'll say why do I need ntfs in the first place? well, I only recently switched for Linux as my primary OS, these are some relics of the M$ era -
I bought the external DVD player/burner for my Macbook. I tried using it with my Dell laptop but it will not work. Is it not configured to work with anything but apple operating systems?
If you purchased the Apple USB SuperDrive, it will only work with select Apple devices. It won't work, for example, on my Late 2011 model that has a SuperDrive built-in, but it will work with an Air, Retina model, new 'drive-less' iMacs, etc.
As far as I know, though, you can only hack the drive to work with some other Apple devices, but not with Windows PCs. Which is a shame as other, less expensive DVD/CD devices will work with just about any machine.
Sorry,
Clinton -
External USB keyboard does not work with T60 after BIOS upgrade
External USB keyboard does not work properly with T60 after 2.26-1.07 BIOS upgrade.
It does the same with or without the docking station.
Anyone else bumped into this problem yet?
Has someone found any fixes for this?
tHi and welcome the forum!
Try uninstalling all USB hub devices from the device manager and reinstalling them again, particularly the keyboard's.
v2.26 is supposed to fix the issue according to lenovo:- http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-63024
Hope it helps.
Maliha (I don't work for lenovo)
ThinkPads:- T400[Win 7], T60[Win 7], IBM 240[Win XP]
IdeaPad: U350
Apple:- Macbook Air [Snow Leopard]
Did someone help you today? Compliment them with a Kudos!
Was your question answered today? Mark it as an Accepted Solution!
Lenovo Deutsche Community Lenovo Comunidad en Español
Visit my YouTube Channel -
I have a mid 2009 macbook pro and my issue is that I installed windows 7 and when I wan to install the drivers it says " bootcamp x64 is unsupported on this computer model" I tried installing the drivers with the bootcamp 4 but it did not work either it says that i have a newer bootcamp version. I tried a few tricks but they didnot work. I hope to be helped
Welcome to Apple Support Communities
You can install a 64-bit Windows 7 or Vista version in your Mac. Make sure you downloaded these drivers > http://support.apple.com/kb/DL1630 Also, if you have the Snow Leopard DVD you used to upgrade your Mac or the OS X DVD that came with your Mac, you can use it to install the Boot Camp drivers -
External Hard Drive does not work with Lion
Hi
My External Hard Drive does not work with Lion this message appears:
NTFS-3G could not mount /dev/disk1s1
at /Volumes/My Passport because the following problem occurred:
/Library/Filesystems/fusefs.fs/Support/fusefs.kext failed to load - (libkern/kext) link error; check the system/kernel logs for errors or try kextutil(8).
the MacFUSE file system is not available (71)
can anyone help?Hi,
See this Discussion:
https://discussions.apple.com/thread/3191198?start=0&tstart=0
Cheers, -
So I cannot scan my pictures, help. Windows 8.1 with HP Officejet 6500A Plus printer. Scanner works with other programs in my PC. Problem is PS12
I bought the Officejet 6500A Plus about one month and have experienced the very same problem. I tried to remedy this problem following suggestions in a number of different posts (static IP, router, firewalls etc), all to no avail. Last week I called support. The support I received by the tech over several hours and different days for a week was very good. However none of his suggestions corrected the connection issue. After today's recommended fix failed, he advised HP is aware of this issue with the 6500 and other affected printers. He claimed HP was working on a firmware upgrade. He did not know when the update would be provided. The tech also claimed HP acknowledged this problem in a written announcement. He agreed to email the announcement to me. I haven't received it. This has been the only problem I've had with the 6500
-
MY EXTERNAL SPEAKER PORT IS NOT WORKING for hp envy
MY EXTERNAL SPEAKER PORT IS NOT WORKING .WHEN I CONNECTED TO A EXTERNAL SPEAKER ,THERE WERE NO SOUND AUDIBLE.SO WHEN I DISCONNECTED THE CABLE FROM PORT,I WAS ABLE TO HEAR WITH THE IN BUILT SPEAKERS.EXTERNAL SPEAKER IS I GOOD CONDITION.I CHEKED WITH MY HEAD SET ALSO.IT WAS NOT AUDIBLE.MY LAP IS HP ENVY .KINDLY HELP
Hi ano87, welcome to the HP Forums. What is the model or product number? What version of Windows is installed?
Guide to finding your product number
Which Windows operating system am I running?
TwoPointOh
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping! -
External hard drive is not working on airport time capsule even after 7.7.2 firmware update.
External hard drive is not working on airport time capsule even after 7.7.2 firmware update.
I have the latest Airpor Time capsule 2gb. I specifically bought it so that I could have an external hardrive set up to wirelessly house my itunes library and movies. When i connect the drive, all i get is that the disk needs to be repaired.
the drive can works fine when connected to the macbook pro and I have run the verify and repair features in disk utility. I have also reset the airport timecapsule as well following these changes and still no change.
The 7.7.2 update says that it addressed the usb issue of not showing the drives but there are still problems as I cannot get it to appear.
Please help.
ThanksHow is the hard drive formatted?
Have you tried using a powered USB hub with the drive when it is connected to the Time Capsule?
(The USB port on the Time Capsule is borderline as far as power is concerned....you may need to use a powered hub.....even if the hard drive has its own power supply)
If the drive is formatted correctly....and....it has ample power, it will "show up" when you open AirPort Utility, click Edit, then click the Disks tab at the top of the next window.
In the example below, my Time Capsule drive is named "Backups" and another drive named "WD Drive" is connected to the USB port on the Time Capsule.
You should see the name of your Time Capsule drive (named "Data" unless you have changed the name) and the name of the USB drive if you perform the same check.
What do you see? -
Windows 7 64 bit and X-Fi XtremeGamer - Bass Redirection Not Working (No Subwoofer)
SWindows 7 64 bit and X-Fi XtremeGamer - Bass Redirection Not Working (No Subwoofer)% Greetings,
Today I ugraded to Windows 7 Ultimate 64 bit edition and am having a problem with my 5. surround sound that previously worked perfectly in Windows Vista Ultimate.
I am using an X-Fi XtremeGamer PCIe card and the problem is that I have full working surround sound, but the bass/ subwoofer isn't working.
Previously in Vista I enabled bass redirection in the Creative Console and this would make the subwoofer work. In Windows 7 in the console there is a bass redirection option but it doesn't work. Also in the Creative Audio Control panel there is NO option for bass redirection either.
Audio sounds tinny and I am 99.9% everything is set up correctley, I think this is a driver problem. At this moment I'm unsure if this issue plagues both the 32bit and 64bit versions of Windows 7 or just the 64bit version (since the console launcher is 32bit).
Anyone had a similar problem and cracked it's Apart from this small glitch Windows 7 is great!
Thanks!WRe: Windows 7 64 bit and X-Fi XtremeGamer - Bass Redirection Not Working (No Subwoofer)h heya, I have exactly the same problem.
running 64-bit windows 7, X-Fi Xtreme Audio sound card, Trust 5. speakers.
the bass used to work in XP because I could enable bass redirection and alter crossover frequency.
these options are now no longer available in the windows 7 drivers (.4.90) and my bass is not working at all.
it is very annoying, there has been no comment from creative than i can find because it only appears to happen to a small percentage of speakers.
basically if someone from creative can't help fix the problem,?people with this problem?will unfortunately be forced to purchase a different brand of sound card because my speakers certainly aren't broken and work with the on-board sound fine.
so if anyone else has the same problem or any advice on how to fix the problem, please comment. -
when using apple tv with my ipad, the mirroring function does not work, screen goes black, what is the issue? My son's Ipad(same as kind as mine) works ok with the apple tv but mine does not. Any suggestions?
Hello Nina Izurin,
While written for the iPhone, the troubleshooting below can help resolve issues with your iPad's camera, as well.
Camera isn't functioning or has undesired image quality
If the screen shows a closed lens or black image, force quit the Camera app.
If you do not see the Camera app on the Home screen, try searching for it in Spotlight. If the camera does not show up in the search, check to make sure that Restrictions are not turned on by tappingSettings > General > Restrictions.
Ensure the camera lens is clean and free from any obstructions. Use a microfiber polishing cloth to clean the lens.
Cases can interfere with the camera and the flash. Try gently cleaning the lens with a clean dry cloth or removing the case if you see image or color-quality issues with photos.
Try turning iPhone off and then back on.
Tap to focus the camera on the subject. The image may pulse or briefly go in and out of focus as it adjusts.
Try to remain steady while focusing:
Still images: Remain steady while taking the picture. If you move too far in any direction, the camera automatically refocuses to the center.
Note: If you take a picture with iPhone turned sideways, it is automatically saved in landscape orientation.
Video: Adjust focus before you begin recording. You can also tap to readjust focus while recording. Exiting the Camera application while recording will stop recording and will save the video to the Camera Roll.
Note: Video-recording features are not available on original iPhone or iPhone 3G.
If your iPhone has a front and rear camera, try switching between them to verify if the issue persists on both.
My issue is still not resolved. What do I do next?
Contact Apple Support.
iPhone: Hardware troubleshooting
http://support.apple.com/kb/TS2802
Cheers,
Allen -
Portege R500 with XP: Offline files from server do not work
I have a strange problem with a brand new R500 with XP installed. Offline files does not work: I can copy files down from servers, but when I attempt to copy back, I get an error
"Offline Files (XXX on YYY): Access to ZZZ is denied on ZZZ."
where XXX is either a samba share or a normal windows share. I have all the permissions to access those files, and can edit them if I go online without synchronising offline changes.
I would ask this on the XP group, but I've +never+ seen this on any other laptops I've used (including Toshiba). Offline files to these servers still works for me on an older laptop (running an up to date XP), using the same account details and even using the roaming profile. Its also not related to any of the standard Offline files problems that are turned up on Microsoft's Knowledge Base.
What more can I test - this problem seems specific to this laptop, and if I can't use offline files, the machine is practically useless to me (modulo paying for, and then setting up an equivalent piece of software).
Should I try uninstalling TrueSuite for example?
AnthonyI have disabled the TrueSuite File Protection and now offline files work.
This would seem to be really important limitation to the software, and I can't find any supporting documentation about TrueSuite, nor any updates for it.
Anthony -
I installed windows 7 to my macbook pro, but my mousepad does not work in windows 7 and also i can not connect my windows 7 to projector, but i can use my macbook's mouse pad and i can connect my mac to projector,so please help me for windows 7 problem
i try to download now, do you think when i download and install the windows support software, can i fix the problem?
-
Problem with new version 4.3.2 apps not working " after update to the new version "
Problem with new version 4.3.2 apps not working " after update to the new version "
i was in 4.3.1 then i do the update , but now after update i face this problem , so what i Supposed to do ?!!Hi There
Had the same problem as you. App would terminate when launched.
Solution to working You Tube app:
-Go to playstore
- Uninstall app (it doesn't remove the app, only removes the update)
- "Et Voila", working again.
This doesn't correct the problem, it's just a workaround for you to be able to use youtube app again.
Hope it helped.
Best Regards -
Hi! I sold my Iphone on ebay. The seller wants to connect the Iphone with his Apple ID, but it did not work because it says that the Iphone is already connected with another Apple ID. How can I get rid of this old connection? What do I have to do?
What to do before selling or giving away your iPhone, iPad, or iPod touch
http://support.apple.com/kb/HT5661
MaggySimpson wrote:
Hi! I sold my Iphone on ebay.
Follow the instructions to remove a device you no longer have.
From here > http://support.apple.com/kb/PH13695?viewlocale=en_US
Maybe you are looking for
-
is there a way usinig quick time player when recording a screen movie of product demonstration better quiality?
-
Adding one effect to all clips in project
I Just need to know how to add the unsharp mask to every clip In my project at once.
-
CC - Objects randomly change when resized, don't center correctly with align panel
I'm not sure how clear these photos are, but here's what's happening. I make a compound object, then when I resize it, it moves anchors around. Note the corners on the 3rd "8" -- they're pinched together. This is happening on a lot of different objec
-
Will i have a problem if i don't update to 10.6.4?
hi, new user. i bought a macbook pro 13 i think right about the same time the update came out and while reading these forums noticed people having some issues 'right after updating to 10.6.4'. so i decided not to do the update, figuring i don't know
-
[SOLVED] Netcfg.service always failing.
Hello, Since systemd got pushed down with an update I decided to jump the ship (even though roughly a week ago I tried it and decided to wait a while, the irony ) With the help of my previous topic and the knowledge that e4rat does work with systemd,