Windows 8 and 8.1 and Bitlocker

Im having major issues using Bitlocker on my Windows machine.
My machine was working fine before I decided to use Bitlocker. I ran the encryption, which took several hours and it said that it was fully encrypted and to restart the machine.
On restarting the Bitlocker password prompt came up and I entered my password correctly but then the Windows system failed to boot correctly and sent my machine into a boot loop, finally saying that it could not fix the issue.
I did a fresh install of Windows 8 Pro and before installing any programs (I thought there may possibly be a conflict somewhere) I used Bitlocker to encrypt the drive once more.
I am still having the same issue now, even with a clean install.
I have finally managed to get back into my system, due to luck more than anything else and I suspended Bitlocker and rebooted and it worked fine so the issue has to be with Bitlocker?
I cant find anyone else that is having this problem so would appreciate any advice anyone can give.
My machine doesnt have a TPM so I have changed the settings to require additional authentification at startup but I really do not understand what the issue is or why there would be a conflict in the boot. Ive checked the boot list to make sure things are
in the correct order and they appear to be. Like I said ive tried most things I can think of but would appreciate any and all advice.

Hi Sm-TH,
“Bitlocker and Windows all work fine until I get a message from the 'Host Process for Windows Tasks' asking to restart the system.”
Do you mean that the machine can be booted successfully with the bitlocker turned on until you got the message ? Have you checked the path of the “Taskhost” process ? Normally the path of it is C:\Windows\System32\Taskhost.exe. When we shut down the machine
,usually we will get a message that this process is trying to finish the shut down task.
Please check the Event Viewer for any errors or warnings about this issue. The logs may give us some very important information for troubleshooting this issue.
The following path may be helpful:
Event Viewer\Windows logs\System or Application
Event Viewer \Applications and Services logs\Microsoft\Windows\(Bitlocker related channels)
Best regards

Similar Messages

I WORK WITH 20+ TABS OPEN, SOMETIMES IF A WINDOW IS ALSO OPEN AND I DON'T CLOSE IT FIRST, MY TABS DON'T REOPEN WHEN I RESTART FIREFOX-HOW CAN I FIND AND REOPEN?

I understand how to set the restore tabs function and have done so. Usually my tabs reopen when I restart, but every once in a while if I have other windows (not tabs) open, and I forget to close them all first, before I close my main window, then when I reopen, my tabs are gone. I have gone to History and I can see the Restore Previous Session and Restore Closed Tabs commands, but they are not highlighted and they don't work. Please advise

Try using the Firefox button > Exit when you go to close Firefox, that should save all your open windows / tabs.

All my purchased song from iTunes are not playing complete (iPod and computer with Windows Vista), unexpectedly stops and continues with next song. What am I doing wrong?

All my purchased song from iTunes are not playing complete (iPod and computer with Windows Vista), unexpectedly stops and continues with next song. What am I doing wrong?

Are the songs playing whole in iTunes? if not download them again.
else read this Apple Support Article on your problem
Have a nice day!

Windows Home Server 2011 and Windows 8.1 desktop

My questions is whether a Windows Live account and a local account can be combined in Windows 8. I asked this question in Microsoft Community and
an MS employee said I should ask my question here.
Is there a way to have both active?
I want to reap the benefits of having a live account to keep everything in sync and fully utilize the features of Windows 8.1 but I have a Windows Home Server 2011 that requires that I have a local user account that matches the server side so that I can
use resources on the server.
I've seen lots of tutorials for switching between the two account types but nothing for combining them.
Is this even possible?
Thanks in advance

Your question has not been answered.
Windows Home Server 2011 does not use domains, so even if you had Windows 8.1 Pro, you'd still be left without a solution. I have one PC with Windows 8.1 Enterprise and that does work with Home Server; and a laptop with Windows 7 Pro and that works fine
too. Like you, I have issues with Windows 8.1 Pro.
Does anyone from Microsoft Server actually read these posts?
@PeterPensive,
the OP's original question was relating to "linking/combining" an MS Account with a Win8.x local account. That question was answered. (the answer is no), so, for a WHS scenario, linked accounts aren't possible, but, in Win8.x, an MS Account might be suitable
for use with WHS.
Are you confirming that an MS Account on Win8.x works ok with WHS?
< Also, this is a community-driven forum - MS staff rarely, if ever, participate here.. >
Don
(Please take a moment to "Vote as Helpful" and/or "Mark as Answer", where applicable.
This helps the community, keeps the forums tidy, and recognises useful contributions. Thanks!)

Windows 7 home premium and windows 8.1 pro op network problem

I have two PC-s, one is with windows 7 home premium and the other one with windows 8.1 pro op system. They are wired via ethernet/ home network. Till I had old Windows XP instead of Windows 7, the two PC-s were connected,
file sharing and device sharing was easy and functioning.
Today it doesn't, windows 8.1 finds the other PC and creating the network, even identifying the different folders on the other PC however as I want to open a file, then loading forever starts, but
on the other side the windows 7 PC is frozen, only the hard switch off helps. ...
Any idea what to do? The diagnose shows that the access was lost.

Here is the forum for you

Windows 7 and windows 8 desktop wired and 7510e printer connected to win 7 wireless

I have a windows 7 64 bit HPavilion Elite 150f desktop set up wired with a 7510e photosmart printer connected to it wireless, now I have purchased a windows 8 desktop HP envy 700-019 desktop.
When I set up my new windows 8 desktop I just plugged it into my wireless router/modem combo and it found my printer and I could just print from it, I did not download any software or drivers for my printer or set up a home group as I was not sure how to set it up but last night I tried to set up a homegroup,
I used my wireless network key and entered it and pressed connect, then I entered the Homegroup password that was downloaded for me from Microsoft, but my windows 7 says homegroup and my windows 8 shows private network so I am not sure what I have done wrong, I chose to only share music and printers, can anyone tell me how to do this correctly as I am not sure that I have done it properly.
On my windows 8 I can go to my printers web site by entering the static IP address that cloud support set up for me and it shows as connected but I do not want to enter any printer code as that is already set up on my windows 7, I can also scan to email on my windows 8 but I am not sure what if any security I have on my windows 8. The last time I had a homegroup set up I payed someone to do it for me so I did it by guess work more than anything, if someone can lead me through it step by step I would appreciate it.

Hi @emma22
I would like to do my best to help, but please bear in mind the issue you are expressing is an inquiry for Microsoft not HP. I did find something I think will be most helpful, and I hope it resolves the issue, but if the issue persists, or you have additional questions, it might be best to reach out to the Microsoft community.
Here is what I found; HomeGroup from start to finish.
In the top right hand corner of the article, you can change it from WIndows 7 to Windows 8. I hope this helps.
Please click the Thumbs up icon below to thank me for responding.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Sunshyn2005 - I work on behalf of HP

I have itunes directory on an external hard drive and want to direct a new installation of itunes on windows 8 to use it. I tried holding down ctrl and clicking itunes and after many tries got it to work one time. When I went back in later it had reverted

I have itunes directory on an external hard drive and want to direct a new installation of itunes on windows 8 to use it. I tried holding down ctrl and clicking itunes and after many tries got it to work one time. When I went back in later it had reverted back to a blank version of itunes and I cant get ctrl to work again. Any other ideas?

This is sometimes caused by a problem with the iTunesPrefs.xml file, normally found at C:\Users\<User>\AppData\Local\Apple Computer\iTunes\iTunesPrefs.xml. Try dragging this to the desktop and trying again.
Alternatively the problem may be that you have McAfee AV and it is preventing iTunes from updating the same file and thus causing the problem. See Why does iTunes delete my itunesprefs.xml? for details.
tt2

In version 3.6 I can not open a website link from original page, I keep getting a new window that is blank and asking me to put in a web address. What has changed with the new version?

When on a page if I click on a web link I get a new window that is blank and asks me enter a web address. This started happening with the new 3.6 version. It seems to have something to do with what I choose for the location in my privacy settings as the window changes with each setting but I still cannot get to the new site. Any ideas? I have no problem with this in IE and I have to keep opening IE when I encounter the problem on Firefox which is annoying.

Start Firefox in [[Safe Mode]] to check if one of the add-ons is causing the problem (switch to the DEFAULT theme: Tools > Add-ons > Themes).
* Don't make any changes on the Safe mode start window.
See:
* [[Troubleshooting extensions and themes]]
If it does work in Safe-mode then disable all extensions and then try to find which is causing it by enabling one at a time until the problem reappears.
* Use "Disable all add-ons" on the [[Safe mode]] start window to disable all extensions.
* Close and restart Firefox after each change via "File > Exit" (Mac: "Firefox > Quit"; Linux: "File > Quit")

Hi. I have a Dell PC running Windows 7 64 bit. I have the latest version of Adobe Reader, It worked yesterday. Today I have job training to do that is due tomorrow morning and I can't open PDF files. I have to open a guide and read it and take a test

Hi. I have a Dell PC running Windows 7 64 bit. I have the latest version of Adobe Reader, It worked yesterday. Today I have job training to do that is due tomorrow morning and I can't open PDF files. I have to open a guide and read it and take a test tomorrow. I have deleted and reinstalled the application. I have rebooted. I have made sure my PDF's are associated with the program. Every PDF on my computer won't open and I get the same error message. It simply says Attempt to access invalid address. How can I fix this? Thanks.

Hi Don,
I have seen this issue fixed for some users by modifying the following registry key:
The key is "HKLM\System\CurrentControlSet\Control\Session Manager\Memory Management" MoveImages
Set the key to 1 instead of 0 then reboot the machine.
In case you still face the issue try the following registry key change:
The only thing you have to do is rename the following key at the REGEDIT, and everything will be fine !!
BEFORE:
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Image File Execution Options\iexplore.exe
AFTER:
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\Image File Execution Options\iexplore.old
Note: Please take a backup of the registry before attempting this change.
Regards,
Rave

Windows 7 pro x64 and palm centro

I'm running windows 7 pro X64 and the software installed just fine, but not the driver. Does Palm have any plans for a solution? Are there any third party drivers that will solve my problem without having to install a bluetooth device on my pc?
Post relates to: Centro (Verizon)

Hello rpiquette, Welcome to the Palm Support Community!
Palm has moved away from their legacy operating system (PalmOS) and on to a new one called webOS. Since Palm Inc. doesn't even own their own software anymore (Palm Desktop) I'd seriously doubt any further support will be forthcoming for Win7, especially for 64-bit architecture.
Palm Inc. has historically not divulged any "future plans" for software (or hardware). Will a third-party develop a desktop client? I have no idea at this point, but the opportunity certainly exists!
WyreNut
I am a Volunteer here, not employed by HP.
You too can become an HP Expert! Details HERE!
If my post has helped you, click the Kudos Thumbs up!
If it solved your issue, Click the "Accept as Solution" button so others can benefit from the question you asked!

Cisco Jabber for Windows in Extend and Connect mode and making outbound calls

Hi guys,
I've set up Cisco Jabber for Windows to use Extend and Connect to control a remote PBX endpoint. I've configured the required CTI-RD device, remote destinations, associated the users to the line and added the devices to end-user controlled device. The extend and connect part is working flawlessly without any issues. I'm able to receive inbound calls on the remote PBX endpoint and control the call (hold, resume, transfer etc.) using the Jabber call window that pops up.
However, I'm unable to make any outbound calls via the Jabber client when in extend and Connect mode. Reading the Extend and Connect guide, I need to configure Dial Via Office (DVO) Reverse. So when the user initiates a Dial-Via-Office reverse call, CUCM calls and connect to the Extend and Connect device (CTI-RD). CUCM then calls and connects to the number the user dialled and finally connects the two call legs.
After attempting to configure DVO-R for Jabber for Windows in Extend and Connect mode following the CUCM feature services guide, i'm unable to get any outbound calls working. From RTMT, i am receiving the following Termination Cause Code: (27) Destination out of order. What i also notice is that there is no calling number for that trace either. I would've thought that the calling party would've been the Enterprise Feature Access (EFA) number.
Has anyone got this working or can provide some guidance?
Thanks.

Hi guys,
I've set up Cisco Jabber for Windows to use Extend and Connect to control a remote PBX endpoint. I've configured the required CTI-RD device, remote destinations, associated the users to the line and added the devices to end-user controlled device. The extend and connect part is working flawlessly without any issues. I'm able to receive inbound calls on the remote PBX endpoint and control the call (hold, resume, transfer etc.) using the Jabber call window that pops up.
However, I'm unable to make any outbound calls via the Jabber client when in extend and Connect mode. Reading the Extend and Connect guide, I need to configure Dial Via Office (DVO) Reverse. So when the user initiates a Dial-Via-Office reverse call, CUCM calls and connect to the Extend and Connect device (CTI-RD). CUCM then calls and connects to the number the user dialled and finally connects the two call legs.
After attempting to configure DVO-R for Jabber for Windows in Extend and Connect mode following the CUCM feature services guide, i'm unable to get any outbound calls working. From RTMT, i am receiving the following Termination Cause Code: (27) Destination out of order. What i also notice is that there is no calling number for that trace either. I would've thought that the calling party would've been the Enterprise Feature Access (EFA) number.
Has anyone got this working or can provide some guidance?
Thanks.

Under Windows 7 Ultimate x64 and Boot Camp, my 27 inch Apple LED Cinema Display checks out as a Generic PnP Monitor and is shown as NOT HDCP compliant. I haven't been able to find any kind of an .inf file to use. Does anyone have a solution?

Under Windows 7 Ultimate x64 and Boot Camp, my 27 inch Apple LED Cinema Display checks out as a Generic PnP Monitor and is shown as NOT HDCP compliant. I haven't been able to find any kind of an .inf file to use. Does anyone have a solution? Or is Apple's implementation of HDCP (if it's there) incomplete?

I am having this same issue. Im not sure if this is the cause but I think this is keeping PowerDVD Ultra 11 from playing back Bluray under Windows 7 / Bootcamp

I bought a Mac Mini for the family but there's something very odd. Windows looks completely different and I'm completely confused. Is this because of Windows 8? How do I get back to my old Windows!

Windows looks completely different and we can't use the computer. We're flumoxed, we did some research and read about this new version of Windows - is this the problem? Is there a way to revert to the older version of Windows? Apple has shot themselves in the foot with this change. Any help would be greatly appreciated.

Macs don't come with Windows. They come with OS X. If you want Windows, you'll need to install it yourself, or return the Mac and buy a PC.

Remote Desktop Gateway on Windows Server 2012 R2 and IPAD

Hi guys,
Would love some help with an issue I been struggling for a couple of days now.
I have a RDS 2012 R2 Gateway configured and it works great with all Windows clients both internal and external communication. The problems comes now when my I want to use IPAD
from APPLE. I installed latest RD Client from Microsoft and it works great from the internal network but as soon the device is moved to an external network the client get an error while connecting. Gateway is located in the domain network.
The error is “Failed to parse authorization Challenge”,
This is what I see in the log file from the RD Client.
[2014-Mar-06 16:53:49] RDP (0): --- BEGIN INTERFACE LIST ---
[2014-Mar-06 16:53:49] RDP (0): lo0 af=18 addr= netmask=
[2014-Mar-06 16:53:49] RDP (0): lo0 af=30 (AF_INET6) addr=::1 netmask=ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff
[2014-Mar-06 16:53:49] RDP (0): lo0 af=2 (AF_INET) addr=127.0.0.1 netmask=255.0.0.0
[2014-Mar-06 16:53:49] RDP (0): lo0 af=30 (AF_INET6) addr=fe80::1%lo0 netmask=ffff:ffff:ffff:ffff::
[2014-Mar-06 16:53:49] RDP (0): pdp_ip0 af=18 addr= netmask=
[2014-Mar-06 16:53:49] RDP (0): pdp_ip0 af=2 (AF_INET) addr=10.25.216.171 netmask=255.255.255.255
[2014-Mar-06 16:53:49] RDP (0): pdp_ip1 af=18 addr= netmask=
[2014-Mar-06 16:53:49] RDP (0): pdp_ip2 af=18 addr= netmask=
[2014-Mar-06 16:53:49] RDP (0): pdp_ip3 af=18 addr= netmask=
[2014-Mar-06 16:53:49] RDP (0): pdp_ip4 af=18 addr= netmask=
[2014-Mar-06 16:53:49] RDP (0): en1 af=18 addr= netmask=
[2014-Mar-06 16:53:49] RDP (0): ap1 af=18 addr= netmask=
[2014-Mar-06 16:53:49] RDP (0): en0 af=18 addr= netmask=
[2014-Mar-06 16:53:49] RDP (0): awdl0 af=18 addr= netmask=
[2014-Mar-06 16:53:49] RDP (0): --- END INTERFACE LIST ---
[2014-Mar-06 16:53:49] RDP (0): Not using any proxy
[2014-Mar-06 16:53:49] RDP (0): Protocol state changed to: ProtocolConnectingNetwork(1)
[2014-Mar-06 16:53:54] RDP (0): Resolved 'MB-RDS-01.contoso.LOCAL' to 'ERROR: Unable to connect to remote PC. Please provide the fully-qualified name or the IP address of the remote PC, and then try again.' using NameResolveMethod_Unknown(0)
[2014-Mar-06 16:53:54] RDP (0): Error message: Unable to connect to remote PC. Please provide the fully-qualified name or the IP address of the remote PC, and then try again.(phase: 0, type: 0, reason: 0, systemCode: 0, systemMessage: )
[2014-Mar-06 16:53:54] RDP (0): Protocol state changed to: ProtocolDisconnected(8)
[2014-Mar-06 16:53:54] RDP (0): Final rdp configuration used: {
    activeUsername = " Contoso\\User01";
    arcTimeout = 1800;
    cacheId = 12BF328DD1C8B841;
    certificatesUseRedirectName = 1;
    configurationVersion = 8;
    font = 1;
    gatewayId = F2EE288CD1C8B841;
    gatewayMode = 2;
    gwAutodetectState = kConnectionGwAutodectedForceGW;
    host = "MB-RDS-01.CONTOSO.LOCAL";
    label = "Murbiten - Terminal Server";
    loadBalanceInfo = "tsv://MS Terminal Services Plugin.1.Contoso_-_Termi";
    mouseMode = "-1";
    port = 3389;
    temporary = 1;
    type = rdp;
    useAlt = 0;
    utilityBar = "-1";
    webFeedVersion = "Windows 2008 R2 or newer";
    connections =     (
       F4BF288CD1C8B841,
        12BF328DD1C8B841
    host = "remote.customer.com";
    id = F2EE288CD1C8B841;
    port = 443;
    temporary = 1;
    type = rdp;
    kCFProxyTypeKey = kCFProxyTypeNone;
[2014-Mar-06 16:53:54] RDP (0): --- BEGIN INTERFACE LIST ---
[2014-Mar-06 16:53:54] RDP (0): lo0 af=18 addr= netmask=
[2014-Mar-06 16:53:54] RDP (0): lo0 af=30 (AF_INET6) addr=::1 netmask=ffff:ffff:ffff:ffff:ffff:ffff:ffff:ffff
[2014-Mar-06 16:53:54] RDP (0): lo0 af=2 (AF_INET) addr=127.0.0.1 netmask=255.0.0.0
[2014-Mar-06 16:53:54] RDP (0): lo0 af=30 (AF_INET6) addr=fe80::1%lo0 netmask=ffff:ffff:ffff:ffff::
[2014-Mar-06 16:53:54] RDP (0): pdp_ip0 af=18 addr= netmask=
[2014-Mar-06 16:53:54] RDP (0): pdp_ip0 af=2 (AF_INET) addr=10.25.216.171 netmask=255.255.255.255
[2014-Mar-06 16:53:54] RDP (0): pdp_ip1 af=18 addr= netmask=
[2014-Mar-06 16:53:54] RDP (0): pdp_ip2 af=18 addr= netmask=
[2014-Mar-06 16:53:54] RDP (0): pdp_ip3 af=18 addr= netmask=
[2014-Mar-06 16:53:54] RDP (0): pdp_ip4 af=18 addr= netmask=
[2014-Mar-06 16:53:54] RDP (0): en1 af=18 addr= netmask=
[2014-Mar-06 16:53:54] RDP (0): ap1 af=18 addr= netmask=
[2014-Mar-06 16:53:54] RDP (0): en0 af=18 addr= netmask=
[2014-Mar-06 16:53:54] RDP (0): awdl0 af=18 addr= netmask=
[2014-Mar-06 16:53:54] RDP (0): --- END INTERFACE LIST ---
[2014-Mar-06 16:53:54] RDP (0): Not using any proxy
[2014-Mar-06 16:53:54] RDP (0): Protocol state changed to: ProtocolConnectingNetwork(1)
[2014-Mar-06 16:53:54] RDP (0): Resolved 'remote.customer.com' to '194.71.11.69' using NameResolveMethod_Unknown(0)
[2014-Mar-06 16:53:54] RDP (0): Resolved 'remote.customer.com' to '194.71.11.69' using NameResolveMethod_Unknown(0)
[2014-Mar-06 16:53:54] RDP (0): Exception caught: Exception in file '/Users/build/jenkins/workspace/rc-ios-develop/protocols/RDP/librdp/librdp/private/httpendpoint.cpp' at line 346
    User Message : Failed to parse authorization Challenge
[2014-Mar-06 16:53:54] RDP (0): Exception caught: Exception in file '/Users/build/jenkins/workspace/rc-ios-develop/protocols/RDP/librdp/librdp/private/httpendpoint.cpp' at line 346
    User Message : Failed to parse authorization Challenge
[2014-Mar-06 16:53:54] RDP (0): Error message: Failed to parse authorization Challenge(phase: 0, type: 0, reason: 0, systemCode: -1, systemMessage: )
[2014-Mar-06 16:53:54] RDP (0): Protocol state changed to: ProtocolDisconnecting(7)
[2014-Mar-06 16:53:54] RDP (0): Protocol state changed to: ProtocolDisconnected(8)
[2014-Mar-06 16:53:54] RDP (0): ------ END ACTIVE CONNECTION ------
en → en
authorization
Adam Bokiniec

Hi Jeremy,
I found a solution, thanks for you effort. The solutions is the following.
First thing that needs to be done is either solution from options below, I did the Solution 1 in my case and added a NPS server to AD. (https://blogs.technet.com/b/networking/archive/2010/01/14/remote-desktop-gateway-client-fails-authentication-with-your-user-account-is-not-authorized-to-access-the-rd-gateway.aspx)
Solution 1
Register the NPS server in Active Directory:
In Server Manager, browse to the following location: Roles\Network Policy and Access Services\NPS (Local).
Right click on the NPS (Local) node and choose Register server in Active Directory.
Click OK to authorize the server when prompted.
Solution 2
Open Active Directory Users and Computers on any Domain Controller of the same domain as the Remote Desktop Gateway.
Add the Computer Name of the Remote Desktop Gateway to the RAS and IAS Servers group.
Situation B
Restart the RDS host and Gateway server.
Secondly and the most important is to configure an alternate address that match your public certificate. My public certificate CNAME is “remote.domain.se”.
All commands need to be run as administrator in PowerShell
To show you current configuration run the following commands:
CollectionName is the Collection Name you created for the RDS deployment.
To get your collection name type
Get-RDSessionCollection
When you got the collection name type
Get-RDSessionCollectionConfiguration -CollectionName "RDS - Terminal Server" | FL *
The default configuration will look like this:
CustomRdpProperty     : use redirection server name:i:1
No to add you public domain name that match the certificate run the following command
Set-RDSessionCollectionConfiguration –CollectionName " RDS - Terminal Server " -CustomRdpProperty "use redirection server name:i:1 `n alternate full address:s:remote.domain.se
Run again to verify your settings
Get-RDSessionCollectionConfiguration -CollectionName "RDS - Terminal Server" | FL *
Now it show look something like this
CustomRdpProperty     : use redirection server name:i:1
                         alternate full address:s:remote.domain.se
IPADs and iPhones can now connect to your environment.
Adam Bokiniec

HT201077 hi my itunes wont open itunes store and my icloud uploads some then stops . i have deleated and reloaded both and still the same i am using a pc on windows 8

I am using windows 8.1 my itunes close down if i try and go into the itunes store. my icloud works for about 5 minnutes then stops. i have deleated itunes and cloud and reloaded both and they still fail.

Check these tips:
iOS: Device not recognized in iTunes for Windows

I bought a new laptop and used Windows Easy Transfer cable and moved all files from one computer to another. I installed iTunes and found my iTunes music Library. However, when I plug in my iPod it says it is already synced with another iTunes Library.

I bought a new laptop and used Windows Easy Transfer cable and moved all files from one computer to another. I installed iTunes and found my iTunes music Library. However, when I plug in my iPod it says it is already synced with another iTunes Library.
I don't see anything in Help that shows when you already have transfered all the files over. Why would it want to erase and sync when I already have all the music folder copied over? I didn't have an issue when I had another technician copy from one laptop to another. Home sharing is also on but not being recognized.

I suspect you only migrated the media folder instead of the complete working library. Either review the transfer process and copy over the entire iTunes folder from your old profile's music folder or see Recovering your iTunes library from your iPod or iOS device.
tt2

Windows 8 and 8.1 and Bitlocker

Similar Messages

Maybe you are looking for