Windows 8 install on new SSD to replace broken HD

My 500GB HD failed on my HP Envy Touchsmart Sleekbook. Before it failed i created a recovery USB stick. I replaced the 500GB HD with a new, blank 240GB SSD. The recovery from my USB stick failed. I ordered new recovery USB stick from HP. Recovery got further this time but then also failed. Recovery got as far as completing the section involving the USB stick but then during the software install part it failed. Tried three times and always failed at the same point.
Is the problem that I have replaced the 500GB drive with a 240GB drive?
FYI during troubleshooting I removed the RAID 0 setup from the on-board 30GB SSD, so that it is currently just another drive on the laptop. Cannot find a way back to the RAID setup utility to recreate it as RAID 0. Don't think this is the problem though?
Any ideas most welcome.
This question was solved.
View Solution.

When requesting assistance, please provide the complete model name and product number (p/n) of the HP computer in question. HP/Compaq makes thousands of models of computers. Without this information it may be difficult or impossible to assist you in resolving your issue.
The above requested information can be found on the bottom of your computer, inside the battery compartment or on the startup BIOS screen. Please see How Do I Find My Model Number or Product Number? for more assistance locating this information. DO NOT include your serial number. Please enter the model/product information into HP's Online Consumer Support page and post it here for our review.
If you have a "ChkErrBB.CMB : Detect some error during PININST_BBV. error", please try the following;
1) Try Recovery - "Detect error during PININST_BBV – Fix: Set BIOS to Factory Defaults
•Boot computer – immediately click / press F10 to get into the BIOS Manager.
•Click on F9 to set the BIOS to factory default.
•Save and Exit
•Redo the Recovery – remember to leave the wireless light “on” during the Recovery... Didn't work for me
2) Set System Date to 8/4/2012 and Redo Factory Reset and System Recovery... Didn't work for me
Ignition75 states "I managed to get the recovery to work, by changing the system date in BIOS to 2012."
3) Set BIOS to factory default, System Date to 8/4/2012 and performed Minimized Recovery (based on one of these posts)... Successful Minimized Recovery... Set BIOS to factory default, System Date to 8/4/2012 and performed Factory Reset... Worked for me
4) Remove the mSATA drive from the computer and
•Boot computer – immediately click / press F10 to get into the BIOS Manager.
•Click on F9 to set the BIOS to factory default.
•Set System Date to 8/4/2012
•Save and Exit
•Redo the Recovery – remember to leave the wireless light “on” during the Recovery.
Please try the above suggestions and report back with your findings.
If you have any further questions, please don't hesitate to ask.
Please click the White KUDOS "Thumbs Up" to show your appreciation
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

Similar Messages

I installed a new SSD drive in my computer and now Adobe Creative Suite Web Premium says I don't have a license. I have license. It was very expensive. I am disabled now, and I need this software working.

I installed a new SSD drive in my computer and now Adobe Creative Suite Web Premium says I don't have a license. I have license. It was very expensive. I am disabled now, and I need this software working. Adobe Acrobat has been a primary tool for accommodating memory problems after a brain injury. (A car ran me down while I was out getting exercise.) I installed the SSD because I needed my management of PDF files to run faster. I called tech support for help when the software first stopped working, but they needed me to give them a number from my original disks. Because of my disability, I've been having someone come in to clean, and the shelves where I kept my software packages were cleared. I've been hunting for them ever since, but I can't look for them myself for very long at a time. Today I finally found them, but now I can't seem to contact tech support. What happened? I don't want to delete my old files because I need the setup to remain unchanged, because I don't do well with changes. I think all I should need is to have someone located the license file on drive E: and move it to wherever it is needed on the SSD drive, but I don't know what to look for.

Tech support is not normally available on weekends. You should contact them as soon as the weekend passes and pick up where you left off with them.

Can I install a new SSD on my MBP without the old hard drive?

Here's the scenario. I'm currently in the Philippines leaving for California for college next week. There, I will buy a new SSD (Samsung 830 to be specific). I want to leave my current HDD (the one in my laptop that I'm using right now) here in the Philippines though as my brother here wants to use it. Is there a way for me to install the new SSD without having my old hard drive with me? My macbook pro is an early 2011 15inch MBP running on Mac OS X version 10.7.3 (Lion). I actually don't want to clone my hard drive or anything because I want to start fresh and new with my new SSD. Most of the tutorials I've read online involve some kind of cloning or having the old hard drive still plugged in and having the SSD connected externally, but these methods won't work for me because I won't have the old hard drive. Thanks so much

The only negative to not having the original drive will be the work needed to reinstall all the apps and reconfigure to your liking. You will also have to decide whether to stay on Lion (which you should update to 10.7.4, BTW) or bite the bullet and take a leap of faith on Mountain Lion.
In either case, to simplify matters you would do well to concoct a Lion or ML bootable installer on a USB stick. In either case, you need to get the corresponding installer downloaded onto the hard drive and, instead of running it to execute the install, extract the coveted InstallESD.dmg image from which you construct the bootable installer. See here for details: https://discussions.apple.com/message/17782820#17782820 The procedure applies the same to both of the latest cat flavors.

Help with Installing a new SSD on my x201

I just purchased a crucial 256gb realssd C300 for my 2month old x201. What is the best way to install the new SSD. I have read that a simple cloning may not be the best approach. Can I do a clean install by using the boot disk I made when I first got the x201 along with the recovery media disks? I searched for a thread on this but haven't been able to find any.
Thanks in advance.

Your old HDD should be already aligned, so cloning is not a problem.
Installing seven from a vanilla media or from the lenovo original media should lead also in aligned partition(s).
You can just check the alignement with Paragon align utility and eventually and you can align after the installation process, whatever method you have choosed to install.

Installing windows 7 on new SSD with no backup or disc

Hi,
My toshiba c660d-1c6 recently crashed big time!
Won't boot at all, hdd (320GB) seems to have died.
Just get a windows boot manager message saying that its encountered a problem, unexpected error etc.
Can't do a hdd recovery and it won't go into the repair menu (F8).
I am therefore looking at replacing it with a new ssd, but how easy will I be able to install windows 7 once I get this new ssd? Could I get a 120GB ssd and use it in my laptop?
I don't have any backups or discs to use, only my win 7 product key on the underside of the laptop.
Any suggestions?
Thanks,

Satellite C660D-1C6 (PSC1YE-01W008EN)
If you failed to burn them, you can obtain recovery discs from Toshiba. You can use those to restore to any internal drive.
Toshiba Europe Backup Media Online Shop
See the section System Recovery Options and Restoring the pre-installed software, which begins on p. 1-10 of the User's Manual (attached).
-Jerry
Attachments:
C660UsersManual.pdf ‏3241 KB

How to install windows on the new SSD

I am planning to buy a SDD.
However, how can I use my Windows Product ID for installing a new system on the SSD;
Is there any recommendations for this situation. I want to keep all lenovo functions in the new SSD.
BTW, it is T420.
THX!
Solved!
Go to Solution.

hi.
did you make the Lenovo recovery dvd set from your original factory windows installation?
if so, then:
- simply swap out the platter drive for the new, blank ssd.
- make sure that your optical drive is listed first in your bios boot order.
- boot disk #1 of the recovery disk set and follow the prompts.
- in short order you'll have the ssd set up with "all lenovo functions" as you've described you wish.
- you won't need the Windows key from the sticker on the bottom of your machine.
if you didn't make the set, then it'll take more work. once you've installed Windows on the ssd, you'll need to get Thinkvantage System Update from the driver matrix here: http://support.lenovo.com/en_US/research/hints-or-tips/detail.page?&LegacyDocID=MIGR-77167 and install it. you'll be able to update hardware drivers and Thinkvantage apps from it. once you've completed that, you can double check the matrix to catch anything newer than offered by TVSU.
hth a bit.
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество
Community Resources: Participation Rules • Images in posts • Search (Advanced) • Private Messaging
PM requests for individual support are not answered. If a post solves your issue, please mark it so.
X1C3 Helix X220 X301 X200T T61p T60p Y3P • T520 T420 T510 T400 R400 T61 Y2P Y13
I am not a Lenovo employee.

Approach for fresh OSX install to new SSD drive with restore from TimeMachine

I have an early 2010 MacBook Pro with running Mavericks with FileVault 2 encryption. The drive seems to be failing. I am not able to boot it up. I get a "Prohibitory" sign with freezing. I have attempted various recovery steps: booting with Command-R, running Disk Utility, attempting to do a full restore from TimeMachine, turning off encryption via terminal/command line with no success. I am not able to mount the disk volume. DiskWarrior doesn't seem to support bootable Maverick volumes. I don't the the existing drive deserves additional time.
I've purchased a new SSD drive and I plan to do a fresh OS install on that drive, followed by a restore of my most recentTimeMachine backup to that drive. My backups are not encrypted. Because the current HDD seems to be toast and is running FileVault 2, installing from scratch and then restoring apps and data seems to be the most realistic approach.
Can somebody please tell me what the preferred sequence of steps would be to do this? Particularly the initial OS X install? Since the new drive will not have a recovery partition, I assume that I cannot do Command-R at boot-time to start the install. My system has a DVD drive, but I don't have a Mavericks install disk.
Comments appreciated...

Restart the computer. At the chime press and hold down the OPTION key until the boot manager appears. There should be a disk icon for your Time Machine backup drive. Select it and click on the arrow button below it. This will start you into a hidden Recovery HD on your Time Machine backup drive. Select the Disk Utility option and click on the Continue button.
1. After DU loads select your SSD (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
2. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Apply button and wait until the process has completed.
3. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
4. Set the format type to Mac OS Extended (Journaled.) Click on the Security button, check the button for Zero Data and click on OK to return to the Erase window.
5. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
6. Quit Disk Utility and return to the main menu. Select the Install OS X option and click on the Continue button.
7. Be sure to select your SSD as the installation target.

My mid-2009 MacBook Pro's hard drive is near death. I want to install a new SSD and work from scratch. Please help.

Recently, my mid-2009 MacBook Pro has been crashing when I close the screen ("it's having a problem recognizing when the screen is closed/open and deciding what to do, error overload etc."). It wasn't an SMC issue so I took it to an Apple Store, ran some tests, and decided my hard-drive is failing.
Not wanting to spend an insane amount of money on some "official apple hard-drive," I want to install a new 256GB SSD instead. Hoping to squeeze as much life out of this computer as possible (in January I upgraded from 4 GB RAM to 8 GB), I would like to try and start from scratch, i.e. back-up important folders, music, photos etc. and only take that to the new hard-drive. If someone could explain all the steps I need to take to safely complete this task (or point me in the direction of a guide) I'd appreciate it.
Potentially Important info:
     Model:                mid-2009 13'' MacBook Pro
     Processor:          2.53 GHz Intel Core 2 Duo
     Memory:             4 GB 1067 MHz DDR3
     Software:            OS X 10.8.4
Some additional questions I have...
     Should I be concerned with making a fully bootable back-up (not sure what that is called) as well? If so, what program should I use to create it?
     How much more life should I try and push out of this computer? I'm an engineering student and really only use it for web-surfing, music, and
          word-processing. The batter was replaced in March, the RAM was upgraded to 8 GB in January. When the battery was swapped, the trackpad went           nuts so that's new too. Only other issues are a slightly loose audio jack and the left side of the screen being slightly wobbly (hinge is worn I'm told).

cwgonzalez1192
     Should I be concerned with making a fully bootable back-up (not sure what that is called) as well? If so, what program should I use to create it?
     How much more life should I try and push out of this computer? I'm an engineering student and really only use it for web-surfing, music, and
          word-processing.
Well there is no "official Apple HD / SSD" in any regard, no worries there.
If as you say youre only using same for surfing and word processing, why the need for a SSD? You would not notice any speed diff. in use on either of those,....in boot times yes, but in word or surfing, not.
You can push it likely a few more years, for mere surfing and word processing,...many many years.   Up TO the point that any major fixes become unrealistic relative to getting a new(ER) machine.
Concerned with a boot clone? yes and no. Its an ideal immediate recovery, since you cannot boot from Time Machine, ....in case of HD crash, recovery takes seconds from boot, or 20 mins or so from removing old and installing a clone. All the prosumers and pros have at least one updated clone of their prime machines.
You can do a "fresh install" if you choose, however if your current drive is FINE, why not merely clone it and save yourself some headache?...., but that is your prerogative of course.    Ideally 2 drives, one to backup your data (you need that regardless of installing a new drive for sake of a backup/archive,...ideally 2 actually, not merely one).
You could clone internal to NEW SSD/HD , ...then offload unnecessary files to an external to free up space and clutter and run off the clone, and this would only take a couple hours......the clone itself takes approx. 40+ mins.
CLONE Apps :
Superduper does not clone the recovery partition, but that is NOT necessary if you keep the original HD as a “backup clone”. Most don’t bother with the recovery partition in a clone, however that is your prerogative.
http://www.shirt-pocket.com/SuperDuper/SuperDuperDescription.html
(Free superduper APP above)
CCC App
http://www.bombich.com/

When i boot i get a flashing folder with a question mark. disk utility doesnt work or read my harddrives to boot with. i installed a new SSD and its not reading that either. i have a macbook pro 2011, any help?

So I came to this problem a while ago. M ycomputer basically froze so I was forced to shut down by holding the button down. When I started it up I got the flashing folder with a question mark. I started it up holding down the command and r keys which brought me to disk utility. Although my computer doesn't read that I have a hard drive to start it up. When I click on the disk utility app, I cannot verify or repair anything either. The buttons won't allow me to click on them. It also shows "Mac OSX Base System" which shows I have files and what not saved. I had been told that I need a new hard drive so I bought and manually installed a OWC SSD 240GB drive and when i booted the computer up it booted up yo the operating system fine with all my files and what not on there. After about twenty minutes, it froze again. I forced a shut down, restarted and the same thing happened. I am not able to choose my SSD to boot up, although thats probably because it doesn't have an operating system installed on it??
i have a Macbook Pro 13" 2011
any help would be great, I'm overall confused.

ryansaint11,
this isn’t Apple support; this is a user-to-user forum. We’re just fellow users of Apple products here.
If you want to boot from your SSD, then you should put the SSD where your HDD currently is, and put the HDD into the optical bay. (That setup will also get you the best performance.) At the moment, you’re still booting from your HDD. Note that you will need to format your SSD in Disk Utility [with the “Mac OS X Extended (Journaled)” format] so that you can install OS X onto it.
Since you have an Early 2011 model, it might or might not have originally come with grey installation DVDs. You will be able to find out whether it did or not by trying to use OS X Internet Recovery to install OS X onto your SSD. If it does not work, or if the installed OS turns out to be Snow Leopard, then it will have originally come with the DVDs, and you should purchase a replacement pair of DVDs from Apple or iFixit; those discs will have your MacBook Pro’s Apple Hardware Test and its iLife apps. If the installed OS turns out to be Lion, then it will not originally have come with the grey installation DVDs, and your Apple Hardware Test will be installed along with Lion, and your iLife apps will be downloadable from the Mac App Store.

Copying Arch install to new SSD

My current Arch install is on an SSD, which is 2 1/2 years old. I'm about to purchase a faster (and larger) SSD to replace it, and reuse the old one in a home server. Is this the best strategy to move my install?
- Do a file level backup of everything to be safe
- dd the entire old SSD to the new SSD (dd if=/dev/sda of=/dev/sdb for example)
- Resize with gparted
Anything wrong with that? Are there any performance or stability reasons to use another method? I've been reading over the SSD wiki, and clearly there is a lot more information available on optimizing SSD performance now. I was going on random blog posts when I set up the current install in March 2010.

DSpider wrote:
https://wiki.archlinux.org/index.php/Fu … with_rsync
Transfer it wherever you want.
Excellent, thanks!

I installed a new SSD, My ipod is not syncing with the original HD

I recently installed a new Crucial M4 SSD. My iTunes library is synced to my HD (/e:) My iPod touch 4g wants to sync with my SSD and does not recognize the original HD is still in my computer. How can I get my iPod to sync with the original HD that contains my iTunes library?

When all the media is in your iTunes library/on the computer:
- Connect the iPod to the comp;uter and make a backup by righ clicking on the iPOd under Devices in iTubes and select Back Up
- Restore the iPod from that backup
Note that the backup that iTunes makes does not included synced media like apps and music.
An iPod can only sync with one iTunes library. gtthe iPod seen the new SSD/iTunes as a new iTunes library.

Will my Bootcamp Windows Install Remain after SSD Install

I currently have a i5 Mac Mini 5.1 with the standard 500gb hard drive installed. Presently the drive is split as 340gb for OSX and 160gb for Windows 8.1 running under Bootcamp. My plan is to install a 250gb SSD in addition to the original 500gb HDD onto which I will clone over my current OSX install, then format the 340gb partition onto which I will then move over my home folder and files whilst keeping the SSD for OSX and applications for optimum performance. My plan is to leave the Bootcamp partition as it is.
My question is will the 160gb Windows 8.1 Bootcamp partition still work or will I have to wipe that partition and start again by re-bootcamping my mac?
Any help and advice is greatly appreciated.
John

Hi Bobthefisherman
Thanks for the reply. That's a real pain having to have them on the same drive as I was hoping to keep the SSD purely for OSX and its applications.
Thanks
John

Setting up OSX after installing a new SSD and moving HDD to optical bay

Hey all,
I know there are a tonne of other posts similar to this one in here, but I couldn't find the specific answers I was looking for.
Soon I'm going to remove my optical bay and put my current HDD in it's place, and install a brand new SSD where the original HDD once was. I'm comfortable with the hardware installation but am wary about what to expect on first power up afterwards.
I would like to ideally run OSX Mavericks and all of my apps (everything from Notepad to Premiere Pro) from the SSD, and leave all of my data on the HDD. I have an early 2011 13" Macbook Pro, model number A1278.
- When I first turn the computer on after the hardware switcheroo, what can I expect to see? How do I re-install OSX Mavericks onto the new drive? Am I right in thinking that Mavericks is merely an upgrade rather than a whole new OSX and that I will need to install Lion and then upgrade to Mavericks rather than just reboot immediately to Mavericks?
- How can I then remove Mavericks from the original HDD?
- Exactly which files do I need to move to completely relocate the apps to the new drive? Is it as simple as moving the entire applications folder over, or are there hidden files dotted all over the place that I need to consider also?
Thanks in advance,
Adam

Adam,
if your current HDD is a SATA III (6.0 Gb/s maximum throughput) drive, then you might find that you’ll have problems with it in the Optibay position. If this is the case, you’d probably be better off putting your SATA III drive into an external enclosure, and purchasing a SATA II (3.0 Gb/s maximum) drive to install in the Optibay.
If you have a SATA-to-USB or SATA-to-FireWire adapter, you can connect your SSD externally and format it with Disk Utility. After that, you could use a cloning utility to copy the contents of your internal HDD to your SSD (presuming that the SSD is at least as large as the amount of space currently used on your internal HDD), and then boot from the external SSD using Startup Manager to make sure that everything works well on it; that will save you from having to make sure that all of the scattered hidden files have been migrated. Once you’ve confirmed that your apps run well from the SSD, you can then install the SSD and move the HDD to wherever it’s going. An advantage of keeping Mavericks on your HDD is that you can boot from it if needed, e.g. should your SSD develop a problem.

Got new iphone to replace broken one-cannot access apps and songs

i tried to syn new phone to replace old phone, but my apps are not syncing/running and my songs are not playing

Make sure you phone is signed into the same Apple ID in Settings>Store>Apple ID that the iTunes store is signed into in iTunes on your computer. If it isn't, tap the ID shown, sign out, then sign back in with the correct ID.

Problems installing Windows to my new SSD

Greetings,
I got a brand new 250gb SSD Samsung 840 Evo hard drive for christmas and have run into a lot of problems trying to install it. I am currently using a 500gb HDD drive in my hp pavilion dv6-7024eo with Beats audio edition.
First i tried using the Samsung Data Migration software but it wouldn't boot when i tried it. The Windows can't find a boot device error so on to idea number 2.
Then i cleaned my SSD with diskpart and attempted a clean install. Set up my windows 7 64bit and it worked. I updated my windows and when it restart it wouldn't boot. Now I got the error code that no hard drive is connected, I then opened up my laptop and double checked all the connections. After that I tried to boot up again and now my good old friend the "Windows can't find a boot device blabla".
Then I formatted the SSD... again and tried setting up windows... again but now the installation won't complete.
So my questions are..
1) Is there something I need to change in the bios so that the SSD will work?
2) Do I need to update my Bios Version? Currently F.29 from Insyde
3) Is this a known problem ? Has anyone cracked the problem ?
4) Is my computer simply not compatible with a SSD upgrade?
Happy holidays and hoping for a swift reply,
Matthías Davíðsson

Sad_customer wrote:
So my questions are..
1) Is there something I need to change in the bios so that the SSD will work?
2) Do I need to update my Bios Version? Currently F.29 from Insyde
3) Is this a known problem ? Has anyone cracked the problem ?
4) Is my computer simply not compatible with a SSD upgrade?
Happy holidays and hoping for a swift reply,
Matthías Davíðsson
1. Is your BIOS ACHI or legacy? It should be in ACHI setup and does the the BIOS see the drive?
2. That you need to check on by using your P/N at HP driver support site to see if there is a BIOS update.
3. What do you mean known problem? That a very general problem question that will be hard to define.
4. You said you were able to format it with Windows 7 that would mean it did work.
5. This could be that your boot up process isn't setup to make the SSD as the main boot drive. This is something you need to check on your BIOS setup.
6. Never do a diskpart on SSD just use Win7 and delete all the parition and format Win7 is already made for SSD.
7. This sounds like a bad Setup in BIOS thus it doesn't see the SSD as a boot drive you need to go and double check the BIOS settings again.
If not sure try this link for some other user replies...
http://www.tomshardware.com/forum/263475-32-windows-detect-shows-bios
I am a Volunteer to help others on here-not a HP employee.
Replies aren't online 24/7 because of Time Zone differences.
Remember in this Day and Age of Computing the Internet is Knowledge at your fingertips if you choose understand it. -2015-

Windows 8 install on new SSD to replace broken HD

Similar Messages

Maybe you are looking for