Windows 8 installation error: "We couldn't create a new partition or locate an existing one. For more information, see the Setup log files."
I recently tried testing Server 2012 for installation and I had a major issue. Windows 8 also uses the same method for installation so this should also apply to Windows 8. I thought this might be helpful for other people who have the same
problem. My setup is a 1U server with no DVD drive, no hard drives, and only USB. I have a new hard drive that I wanted to install Server onto, so I put it in and ran the installer off a thumb drive. I kept receiving the following error when
I tried to format the hard drive and proceed with the installation:
"We couldn't create a new partition or locate an existing one. For more information, see the Setup log files."
After hours of troubleshooting, I determined my problem was I was using a thumb drive to install it, and Windows didn't like it. Some people had similar issues when similar devices were plugged in (i.e. external hard drives, SD cards, CF cards, etc).
In my case, it was the installation drive itself was a thumb drive. I ended up digging up an external DVD drive and placed the installation onto a DVD. Worked flawlessly. Now I am up and running.
I tried
the steps here to no avail.
Hope this helps anyone else with the same problems.
Hi,
Thanks for sharing. We really appreciate your time and efforts. Hope your experience will help other community members facing similar problems.
Leo Huang
TechNet Community Support
Similar Messages
-
Ok so back in August 2014 I succuesfully used bootcamp to install Windows 10 Tech preview. It worked great until March of this year when Windows issued an update (Which I had no control over). After this update the R9 4GB graphics card driver stopped working. I contacted Apple/AMD/Microsoft but was unable to fix this problem.
So, I uninstalled Windows 10 through bootcamp and restored the drive to a single partition. I purchased windows 8.1 and downloaded Windows Enterprise edition (as this comes as an ISO file) and started the process again with Bootcamp. Everything works great until I get to the installation of windows.
I did the same as last time (formatted the Bootcamp partition) and tried to continue the installation. I now get the following message:
I have tried a complete reinstall of the system twice (back to factory settings) but still the same issue. I have also tried using Windows 10 Tech preview but still the same issue. (I only have my remote drive with the ISO file connected to the mac and have tried with a USB stick)
Any ideas would be much appreciated! ThanksThank you for your prompt response. Please see below:
Last login: Thu Apr 30 09:15:48 on console
Jeremys-iMac:~ jeremygaster$ diskutil list
/dev/disk0
#: TYPE NAME SIZE IDENTIFIER
0: GUID_partition_scheme *121.3 GB disk0
1: EFI EFI 209.7 MB disk0s1
2: Apple_CoreStorage 121.0 GB disk0s2
3: Apple_Boot Boot OS X 134.2 MB disk0s3
/dev/disk1
#: TYPE NAME SIZE IDENTIFIER
0: GUID_partition_scheme *1.0 TB disk1
1: EFI EFI 209.7 MB disk1s1
2: Apple_CoreStorage 999.3 GB disk1s2
3: Apple_Boot Recovery HD 650.0 MB disk1s3
/dev/disk2
#: TYPE NAME SIZE IDENTIFIER
0: Apple_HFS Macintosh HD *1.1 TB disk2
Logical Volume on disk0s2, disk1s2
E693210D-5893-4CC0-B3FF-18B5A92179CB
Unencrypted Fusion Drive
Jeremys-iMac:~ jeremygaster$ diskutil cs list
CoreStorage logical volume groups (1 found)
|
+-- Logical Volume Group 5BEBA89D-FBF8-45AF-99CF-DFB82BC6B9E8
=========================================================
Name: Internal Drive
Status: Online
Size: 1120333979648 B (1.1 TB)
Free Space: 114688 B (114.7 KB)
|
+-< Physical Volume 2EF54FBF-26BB-4D56-A84E-947205800865
| ----------------------------------------------------
| Index: 0
| Disk: disk0s2
| Status: Online
| Size: 120988852224 B (121.0 GB)
|
+-< Physical Volume B66237C5-F9ED-454C-9AFB-90553B0D0E0A
| ----------------------------------------------------
| Index: 1
| Disk: disk1s2
| Status: Online
| Size: 999345127424 B (999.3 GB)
|
+-> Logical Volume Family A91C5378-D285-434D-B33B-5F1E0CC64C62
Encryption Status: Unlocked
Encryption Type: None
Conversion Status: NoConversion
Conversion Direction: -none-
Has Encrypted Extents: No
Fully Secure: No
Passphrase Required: No
|
+-> Logical Volume E693210D-5893-4CC0-B3FF-18B5A92179CB
Disk: disk2
Status: Online
Size (Total): 1114478608384 B (1.1 TB)
Conversion Progress: -none-
Revertible: No
LV Name: Macintosh HD
Volume Name: Macintosh HD
Content Hint: Apple_HFS
Jeremys-iMac:~ jeremygaster$ sudo gpt -vv -r show /dev/disk0
WARNING: Improper use of the sudo command could lead to data loss
or the deletion of important system files. Please double-check your
typing when using sudo. Type "man sudo" for more information.
To proceed, enter your password, or type Ctrl-C to abort.
Password:
Sorry, try again.
Password:
gpt show: /dev/disk0: mediasize=121332826112; sectorsize=512; blocks=236978176
gpt show: /dev/disk0: PMBR at sector 0
gpt show: /dev/disk0: Pri GPT at sector 1
gpt show: /dev/disk0: Sec GPT at sector 236978175
start size index contents
0 1 PMBR
1 1 Pri GPT header
2 32 Pri GPT table
34 6
40 409600 1 GPT part - C12A7328-F81F-11D2-BA4B-00A0C93EC93B
409640 236306352 2 GPT part - 53746F72-6167-11AA-AA11-00306543ECAC
236715992 262144 3 GPT part - 426F6F74-0000-11AA-AA11-00306543ECAC
236978136 7
236978143 32 Sec GPT table
236978175 1 Sec GPT header
Jeremys-iMac:~ jeremygaster$ sudo fdisk /dev/disk0
Disk: /dev/disk0 geometry: 14751/255/63 [236978176 sectors]
Signature: 0xAA55
Starting Ending
#: id cyl hd sec - cyl hd sec [ start - size]
1: EE 1023 254 63 - 1023 254 63 [ 1 - 236978175] <Unknown ID>
2: 00 0 0 0 - 0 0 0 [ 0 - 0] unused
3: 00 0 0 0 - 0 0 0 [ 0 - 0] unused
4: 00 0 0 0 - 0 0 0 [ 0 - 0] unused
Jeremys-iMac:~ jeremygaster$ -
Posted the entire text from the error window, when trying to update, using the normal NON-TECHIE way to update any and all Adobe CC products, via the Creative Cloud updater installed when Adobe Creative Cloud subscription was purchased when first offered.
The following occurs, ad nauseam:
There was a problem updating InDesign CC
For more information see the specific error below.
Update Failed
Download error. Press Retry to try again or contact customer support.(49)
Here's the crux of my frustration:
(1) Customer Service is NOT contact-able, to receive LIVE help.
(2) There is NO way for me to mitigate this "Download error", being a student learning InDesign, and NOT in any way capable of tweaking folders/files here and there.
Therefore, the real question:
Given that a significant number of subscribers are having the above referenced issue with attempting to download the current update for InDesign, WHAT ARE WE SUPPOSED TO DO, in order to get our contractually paid-for updates to our legally and contractually paid-for Adobe software, specifically in my case, InDesgin's current update?
Please, NO TECHNICAL mumbo-jumbo which most likely will cause the overwhelming majority of users, like me, to seriously corrupt their computer files, but rather an honest, straightforward "what to do" from real CS/Engineers working for Adobe, as to how to FIX this issue, period.
===========================================================
UPDATE:
Here is a way in which I think I was able to "update" my InDesign CC application:
(1) Sign-In to your Adobe Account
https://www.adobe.com/
(2) Click on the MENU icon
(3) Click on the product InDesign icon
Your browser should display the page for Adobe InDesign CC
https://www.adobe.com/products/indesign.html?promoid=KLXLU
(4) Click on the Download icon,
Your browser should now display the page to download InDesign,
https://creative.adobe.com/products/download/indesign
(5) a Pop-Up window should open, and display:
Launch Application
This link needs to be opened with an application.
with the first option to select being the CreativeCloud(URIHandler)
(5) Select this application and click OK.
What happened when I followed steps (1) thorugh (5) is that:
(a) InDesign CC(2014) was installed,
(b) InDesign CC, updated, and then
(c) InDesign CC(2014), also updated.
Why this all worked, is a mystery to me.
Looks like a separate, "new" version of InDesign, InDesign CC(2014), was installed, the existing "old" InDesign was updated, and then the newly installed Indesign CC(2014) was further updated.
A BIT MORE, when I launched my InDesign CC app, and checked to see if there were Updates Available, there in fact was an Adobe InDesign CC 64 bit (9.2.2) update.
I clicked on UPDATE and my "old" InDesign CC app was "successfully updated."
FURTHER INFO: I may have neglected to list some important info ... OS: Windows 8.1 Pro with Media Center, 64-bit
Confused, I am able to launch BOTH of these apps, and hopefully I may use one of these versions of the InDesign CC app, to do some InDesign work.
Will keep y'all posted!
Message was edited by: Richard Yapkowitz, about an hour after I first posted this issue.Jackdan error 49 indicates the installer was unable to access a critical file or directory. You can find additional details at Error downloading Creative Cloud applications - http://helpx.adobe.com/creative-cloud/kb/error-downloading-cc-apps.html.
-
I installed Exchange Server 2010 inside my VMWare Windows Server 2008 Ent R2. And After successful installation when I try to open my Exchange Server Console, I am getting the following error message. I am very new to Exchange server please help me
to solve this problem.
Initialization Failed
The following error occurred while searching for the on-premises Exchange server:
[win-.local] Connecting to remote server failed with the following error message : Access is denied. For more information, see the about_Remote_Troubleshooting Help topic. It was running the command 'Discover-ExchangeServer -UseWIA $true -SuppressError
$true -CurrentVersion 'Version 14.1 (Build 218.15)''.
Thanks Vivek
SharePoint Foundation 2010 Book
http://www.redpipit.comHi,
Please have a look at the article below:
Troubleshooting Exchange 2010 Management Tools startup issues
http://blogs.technet.com/b/exchange/archive/2010/02/04/3409289.aspx
Resolving WinRM errors and Exchange 2010 Management tools startup failures
http://blogs.technet.com/b/exchange/archive/2010/12/07/3411644.aspx
Besides, please run the cmdlet below:
set-user alias -remotepowershellenabled$true
Xiu Zhang
TechNet Community Support -
Habe mir einen neuen Laptop bestellt (Win 8.1) habe auf diesem die Installation ohne Probleme durchführen können. Der Laptop musste aber wegen technischen Defekts gegen einen neuen getauscht werden.
Auf diesem funktioniert die Installation nicht mehr.(Fehler siehe oben in Threadbeschreibung) Habe auch schon nach Lösungen gegoogelt - die Tipps von "Neu aufsetzen" bringen mir nichts da der Computer nagelneu ist.
Der Fehler kommt sowohl beim installieren von CD und bei der heruntergeladenen Version.
Wo ich dieses Log-File finde weiß ich nicht.
Daten zum Laptop (Falls diese benötigt werden) Dell Inspirion 15 7000er Serie mit einem i7 2,0Ghz, 16GB Ram, 2Gb Grafikkarte und Windows 8.1 64bit.
Habe die CD auf dem Rechner von meinem Dad (Win XP SP3) versucht zu starten, dabei entsteht der gleiche Fehler.
Vielen Dank jetzt schonmal für die Hilfe
SvenHabe mein Windows nun doch nochmal neu installiert - siehe da es funktioniert.
Schwach finde ich von Adobe keinen Support mehr am Telefon anzubieten. Mag zwar sein das Cs4 nicht mejr aktuell ist aber dennoch zu sagen es gibt keinen Support mehr ist schwach! Die Damen und Herren in der Geschäftsleitung mögen es zwar nicht glauben aber es gibt auch Menschen auf diesem Planeten die nicht mit Geld um sich werfen können.
Ich wünsche mir für die Leute da oben auch mal ähnliche Probleme in einer Autowerkstatt wenn sie mit ihren Oldtimer ein Problem haben und dort dann gesagt wird das dieses Fahrzeug leider nicht mehr repariert werden kann weil es zu alt ist.
Danke an die Hilfe die ich bekommen habe - auch wenn sie nicjts gebracht hat. -
I AM UNABLE TO INSTALL WINDOWS 7 HOME PREMIUM ON MY LAPTOP
MY LAPTOP SPECIFICATIONS ARE=
1 GB RAM
INTEL GMA 900 MOBILE SERIES
INTEL ATOM
160 GB HDD
CURRENTLY RUNNING LINUX MINT 15
THE ERROR=
SETUP WAS UNABLE TO CREATE A NEW PARTITION OR LOCATE AN EXISTING ONE CHECK SETUP LOG FOR MORE INFORMATION
PLEASE REPLY FASTi tried out this method it doesn't work. Actually i have a nOTEBOOK which came with windows xp i planned to upgrade it because microsoft has stopped supplying updates.
my NOTEBOOK is of Medion company.
modal=akoya e1210
msn no.30008507
LINK FOR NOTEBOOK OFFICIAL PAGE AND SPECS
http://www.pcpro.co.uk/reviews/laptops/247451/medion-akoya-mini-e1210
by the thanks for replying an method -
Dear Technet,
Windows could not start the Cluster Service on Local computer. For more information, review the System Event Log. If this is a non-Microsoft service, contact the service vendor, and refer to service-specific error code 2.
My cluster suddenly went disappear. and tried to restart the cluster service. When trying to restart service this above mention error comes up.
even i tried to remove the cluster through power-shell still couldn't happen because of cluster service not running.
Help me please.. thank you.
Regards
ShamilHi,
Could you confirm which account when you start the cluster service? The Cluster service is a service that requires a domain user account.
The server cluster Setup program changes the local security policy for this account by granting a set of user rights to the account. Additionally, this account is made a member
of the local Administrators group.
If one or more of these user rights are missing, the Cluster service may stop immediately during startup or later, depending on when the Cluster service requires the particular
user right.
Hope this helps.
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place. -
I am using Win XP Pro SP3. I have CS3 installed, and successfully installed Dreamweaver, Fireworks and Flash from CS4 Design Premium. Then I successfully uninstalled DW, FW and FL CS3.
When I tried to open a SWF in Illustrator it failed to open, and then I tried to create a really simple SWF (a rectangle) by exporting from Illustrator and tried to open that and it also failed. Whenever I tried to open or place ANY SWF into Illustrator I get a "file *** is in an unknown format and cannot be opened" error.
I decided there must be a corrupt file, maybe the upgrade must have affected some Illustrator files, so I tried to repair the CS3 installation. After over 2 hours of INTENSE FRUSTRATION having to constantly switch CS3 and CS4 disks many MANY times, the installation failed, listing "common files" that were missing from non-existent folders such as "C:\Documents and Settings\[username]\Desktop\Adobe CS4\Fireworks CS4\payloads\etc
When I tried to repair the CS4 installation after loading all the profile settings it errors before the installation window comes up, with "Critical errors were found in setup. Please see the setup log for details". Then it shuts down the installer. I then tried to do a system restore and system restore failed on all restore points!
Please help:
1. Where is "the setup log"?
2. Will creating and populating the folders mentioned in the failed CS3 installation from the CS4 disk allow it to work?
3. How can I uninstall CS4 if I can't even get to the installation window?
4. Has Adobe just DESTROYED MY REGISTRY BEYOND REPAIR!!!???im haveing a huge irritation useing illustrator cs4 live paint bucket because i can use everything else apart from the paint bucket which should be the easyiest tool to use sometimes it works with the white arrow sometimes it doesnt i sometimes get this below message
the selection contains objects that cannot be converted. live paint groups can only contain paths and compound paths. clipping paths are not allowed
the lines which i have drawn are connected which i believe have to be in order to use the paint bucket and i have no clipping paths so i am am baffled
i presume it is because the line is set to 0.01 it seems the live paint bucket wont notice thin lines, but i tried makeing the line thicker so i could use the paint bucket and it still doesnt work. -
Best Practice for Creating a New WebHelp Project from an Existing One
I'm currently working in WebHelp Pro (RH version is 9.0.2.271).
I have a WebHelp project which currently supports the 2012 version of one of our projects. What I needed to do was to create a separate 2013 project, using the 2012 files as the starting point. I couldn't find a way in RH to create a new project by importing an existing WebHelp project, so I copied the 2012 files to a new directory, opened up the project, and renamed it.
What prompts this question is that following this exercise, all seemed well, for a time. However, I have recently had to create new topics in the 2012 version. However, when I imported these topics to the 2013 project and compiled, they vanished--although the htm files still appear in the appropriate 2013 file folder (when viewed with Windows Explorer).
After reading some forum postings, I thought that I might have corrupted my database by improperly creating the new project--but if what I did is the wrong way to go about it, I'm not sure what the correct way is. I will be grateful for any suggestions.The easy way to do this is create a copy using Windows Explorer.
Open the project and go to File > Rename.
Then you have your 2013 ready made project.
See www.grainge.org for RoboHelp and Authoring tips
@petergrainge -
Critical Errors Were Found in Setup. Please see the Setup Logs for Details
Hello everyone. I have recently gotten Adobe Flash CS4 and i was really happy, until i kept getting the same error whenever i tried to install:
"Critical Errors Were Found in Setup. Please see the Setup Logs for Details"
I do not know what is the cause of the problem, but i have installed Adobe Photoshop CS3 succesfully without any problems. Please do help. I checked the setup logs, but i have no clue what it is saying, and its too long to post here.
Thank you for your time and help.We've all been there with the frustration.
And I'd really like to see you get back up and running. I'm a bit of an insomniac and tend to go back over the day while I'm pretending to sleep, and a couple of new things filtered back into my mind. There have been, I think, some problems reported about conflicts with some scanner drivers, and of course with firewalls, anti-virus programs, and the like. I think iTunes and instant messengers are also on that list.
Make sure you turn off everything non-essential before trying to do your installation (and I'd probably do the same thing before running the scripts again). I do this by running MSConfig on XP and going to the startup tab. I uncheck everything I can't identify as being essential (which means I pretty much only leave the mouse driver checked. You may need to google some of the stuff to find out what it is) and then go to the services tab and hide all Microsoft services. From what's left I again uncheck everything that isn't required to run the system. Bonjour, if you see it, should be left active as it is used by the CS3 installer. Restart the computer.
This should have turned off pretty much everything that could have been conflicting with the installer. Go to windows security center and make sure the windows firewall is also temporarily turned off, if you use it, and you should be ready to go. It can't hurt to try the add/remove programs again, but it probably won't show any adobe products anymore if you've run the scripts correctly (did you also run the MSI cleanup utility?).
After you've finished, you can run MSConfig again and reset to standard startup.
Peter -
I created an new apple id and want to change my billing information from the old id to the new id. How do i do that, as i have been trying it like always and it keeps saying that i have to contact apple support? I have an iphone 5S.
Good day BenithaK,
Once you have changed your Apple ID, you need to set it up for use in the various systems such as iTunes, the App Store, etc so it can be used as intended. This article shows how to do that -
Apple ID: What to do after you change your Apple ID - Apple Support
To change your iTunes billing information for either Apple ID account, follow the directions in this article -
iTunes 12 for Mac: Manage your iTunes Store account
Thanks for using Apple Support Communities.
Safe computing,
Brett L -
some one can help me please
i have no idea what i must to do.
an unhandled exception occurred during the execution of the current web request. Please review the stack trace for more information about the error and where it originated in the code.The Exception Handler gave all the info that you need. No need to print the whole stack trace.
The exception handler says
Exception Details: java.lang.IllegalArgumentException
TABLE1.NAME
Look in the session bean (assuming that is where your underlying rowset is). Look in the _init() method for statements similar to the following:
personRowSet.setCommand("SELECT * FROM TRAVEL.PERSON");
personRowSet.setTableName("PERSON");
What do you have? -
SMTP Error Code : 530 . For more information, see your SMTP server manual.
Hello,
I am Getting
"SMTP Error Code : <530>. For more information, see your SMTP server manual" error, While configuring SMTP in Data Services 4.0 system. I have tried executing the SMTP_TO function on another DS machine which has 3.2 verion installed, but getting the same error.
FYI,
1) Able to telnet the Exchange server through Data service machine
2) Maintained SMTP settings in Data services server manager
3) using the same SMTP server host name in other SAP systems (ECC,BI,PI) etc and able to send mails.
Regards
PuneetThanks for the reply Julian.
There was a problem in SMTP relay rights on Exchange server. Able to send mails now. Thanks!
Getting another problem wherein I am not able to send mails to multiple recipients i.e. If I specify 5 recipients in SMTP_TO function and execute the job then Every individual is getting E-Mail having there own ID in TO field, other Id's are not gettting displayed in TO field.
I hve checked note "1276348 - smtp_to function - multiple recipients not displayed"
Settings mentioned in the note have been done and job is getting executed without any error but the mails are not getting delivered.
It would be great if anyone can suggest on how to proceed here.
Thanks & Regards
Puneet -
Couldn't create a new partition with a windows 7 installation
Hi
I have a b570 laptop. It was originally windows 7 home premium and I wanted to install windows 7 ultimate from scratch (didn't want to upgrade it) with new partitions, so I have deleted the original system partition and tried to create a new partition but to my surprise I couldn't create a new one. I tried to use the onekey recovery but it keeps asking me for the original partition, which I don't have. Please help me if you know how I could solve this problem. Thank you in advance.With the windows 7 installation disk...I select the unallocated space shown on the screen -> click on the new button on the bottom -> set the size of the new partition to be created -> and click create.
-
Hi all,
I have set up the preview for the new Azure SQL tiers on both of the subscriptions we have for Azure. The one under my MSDN subscription to and a pay as you go subscription
The pay as you go subscription works fine but when I try to upgrade an existing Azure sql database or create a new one on my MSDN subscription it doesn't give me the option of the new tiers.
Using the new portal it says I need to sign up to the preview, but I already have and when I go to try to add a new subscription to the preview for Azure SQL it says all my active subscriptions are on the preview.
Any idea what the issue could be?
Cheers
AshHi,
Apologies for the inconvenience.
I suggest you open a Billing Support Ticket. They will be able to check this for you.
http://azure.microsoft.com/en-us/support/options/
Regards,
Mekh.
Maybe you are looking for
-
I have two email accounts that my iTunes keeps getting mixed up. How do I delete one of the emails from my iTunes so it only goes to my .me account?
-
Premier pro cs6 but not reconizing my aja kona Lhi capture card
tried different driver and plugins but still can't capture with card
-
How to maintain currency decimal notation
Hi all, we want to display currency format 1,234,567.89 but we are getting current format as 1.234.567,89 we already maintained the required format in the USER PROFILE's DEFAULT still we are getting this format 1.234.567,89 so is there any t
-
How to reset iPod back to it's original
Hi There- I know this is a simple question, but how do you set an iPod touch back to it's original state ?? I'mm selling mine cause I've upgraded to an iPad. Thanks for your time. Sincerely- Doug
-
where is the Devices tab? you have a "connected devices" (which is Not the same) and there is nothing you can do on that screen. this whole experience is sending me back to Canon or Epson.