Windows 8 not printing on Airport Time Capsule

Windows 8 will not connect with a printer through the Airport Time Capsule.

Ok, thank you.
I am assuming that this printer shows up correctly on the Printer tab in the AirPort Utility ... correct?
Have you updated the Windows 8 version of the printer drivers from the manufacturer's support site yet? If not, please do. If, per chance, HP does not have Windows 8-specific drivers for this printer may be an indication that it is not supported, especially when connected to an AirPort router.
Finally, have you installed Bonjour for Windows on your laptop? If not, please do.

Similar Messages

External hard drive is not working on airport time capsule even after 7.7.2 firmware update.

External hard drive is not working on airport time capsule even after 7.7.2 firmware update.
I have the latest Airpor Time capsule 2gb. I specifically bought it so that I could have an external hardrive set up to wirelessly house my itunes library and movies. When i connect the drive, all i get is that the disk needs to be repaired.
the drive can works fine when connected to the macbook pro and I have run the verify and repair features in disk utility. I have also reset the airport timecapsule as well following these changes and still no change.
The 7.7.2 update says that it addressed the usb issue of not showing the drives but there are still problems as I cannot get it to appear.
Please help.
Thanks

How is the hard drive formatted?
Have you tried using a powered USB hub with the drive when it is connected to the Time Capsule?
(The USB port on the Time Capsule is borderline as far as power is concerned....you may need to use a powered hub.....even if the hard drive has its own power supply)
If the drive is formatted correctly....and....it has ample power, it will "show up" when you open AirPort Utility, click Edit, then click the Disks tab at the top of the next window.
In the example below, my Time Capsule drive is named "Backups" and another drive named "WD Drive" is connected to the USB port on the Time Capsule.
You should see the name of your Time Capsule drive (named "Data" unless you have changed the name) and the name of the USB drive if you perform the same check.
What do you see?

My iPad and iPhone are not seeing my airport time capsule

MY iPad and iPhone are not seeing my airport time capsule.

You cannot back up directly to a Time Capsule from an iPhone.
iOS backups are done using either iCloud or iTunes as documented here:
iOS: Back up and restore your iOS device with iCloud or iTunes

Can not connect to airport time capsule

Here is what the current situation is:
I can setup the Airport Time Capsule (3GB) form my Mavericks 10.9.4 MacBookAir 2013 using AirPort Utility. However, after setup, I cannot connect to the time capsule using many of the standard ways. Trying both connections of wired and wireless. I have tried:
1. Connecting to the Time Capsule using Time Machine (which I can see the Time Capsule Drive as a selection), and I always get the error "There was a problem connecting to the server “XXXXXX”. Check the server name or IP address, and then try again. If you continue to have problems, contact your system administrator."
2. Using Finder side bar under Shared (which I can see the Time Capsule Drive as a selection), clicking on it, always says Connection Failed at the top of the window. Clicking the Connect As... button results in the same error message as #1.
3. Using Finder, connect to server option, entering the name of the time capsule with .local at the end, and using the ip address and it always returns the same error as #1.
Trying option #3 and looking at the Console for error messages always produces these two messages:
Date Time NetAuthSysAgent[1093]: ERROR: AFP_CreateSessionRef - AFPLoadModules failed 22
Date Time NetAuthSysAgent[1154]: NewAFPLoadModules: bootstrap_look_up failed Unknown service name
Any help would be much appreciated. My computer has security scripts run on it that my company wrote inhouse and not sure exactly what is locked down and not locked down. Thank you.

Using method 3.. try
SMB://TCname.local or SMB://TCIPaddress (I hope obvious you replace with actual name or actual IP).. Please use names that are SMB compatible.. ie short, no spaces and pure alphanumeric.
No luck try CIFS:// etc.
This forces it to SMB1.
No luck ping the TC in terminal.. does it respond??
Do you have ipv6 set ot link-local only in the computer??
Your company may have locked you out.. I would not be surprised. Are you running a vpn on the computer whilst trying to connect to the local network. That will fail and the ping test will show you why.
Date Time NetAuthSysAgent[1093]: ERROR: AFP_CreateSessionRef - AFPLoadModules failed 22
Date Time NetAuthSysAgent[1154]: NewAFPLoadModules: bootstrap_look_up failed Unknown service name
Interesting.. it is blocking AFP perhaps. AFP modules refused.. I do not know the errors well enough but if AFP fails there is a good chance TM won't work. So even if you can mount and access the disk I am not sure you can do TM backups.

Guest Network Not Working On Airport Time capsule

Whenever I enable the guest network and join it, it joins fine. but it wont load any webpages or the app store, or anything. all the devices im trying to connect, connect to the guest network fine. but they just wontt get wifi signal from the TC.
I can get the normal and 5GHz network to work.
I have the TC router connected to a Tp Link modem and setup as its own network.
If i change the router mode on the TC to DHCP and NAT it works but the amber light flashes on the TC which annoys me. then it stops working and i end up having to change under network in airport utility to off (bridge mode)
Please help somebody???
Any help will be much appreciated

Check the client is getting proper DNS address .. there is a bunch of bugs..
The main bug is that guest network does not actually work when the TC is in off bridge mode.. it looks like it is going to work but it doesn't.
The TC must be the main router of the network..
So bridge your TP-Link and use PPPOE client in the TC if that is allowed by your ISP.
Or simply ignore the double NAT and then the light will go green and not bother you any more..
Or an even better solution.. use the TP-Link wireless for guest.. and use the TC in bridge for main network.. there is nothing wrong with doing that.. and in fact it will work far better since guest network is still sharing the wireless on the TC and slowing it down.

I can not start up airport time capsule.

The problems seems to be internet connection. my modem is working properly, ethernet cable is connected from the modem to the WAP ethernet at the airport TC. I reset both systems to check compatibility nothing happens.

Ok.. wifi is working so the basic TC is operating.
What is the modem? If it is a cable modem did you power cycle it for at least 30min off.
You cannot simply change devices on a cable modem.. the Cable system registers the first client and assigns it the public IP address. You MUST force the cable ISP to release this address so it can be assigned to the TC.
Sometimes 15min is enough.. sometimes overnight is needed. Who is your ISP?
Sometimes you will need to call your ISP and get them to reset the modem port.
Some cable modems are a real pain.. eg SB6121 or 6141. That is why the model of the modem is important.
Keep telling us more info..
A screenshot of the TC settings for internet can also help.

Airport time capsule not found error message

HI,
My time capsule is blinking orange.
I open aiport, sometimes airport finds the TC, sometimes not.
When not, get message:
"airport time capsule not found"
When TC is found, aiport utitily shows an error with the extended network I am setting up. I press 'edit', the settings all seem good. Re-type passwords etc and update.
The problem remains.
I have updated the firmware. An apple shop near me has reset TC using the recessed button on back of TC, and then I have re-configured at home.
BTW, TC was working fine in my old house with same laptop, so prob not simply a basic user issue...
4 other devices on my wifi network all have reliable connection, visitors' phones and laptops too, so shouln't be a wifi netowrk issue, ie network outside TC.
Any thoughts out there?
HOpe so!
mana

yes, running airport 6.1, OS 10.7.5
OK.. I failed to ask enough questions.. I think your comment it all used to work threw me.
1. You are trying to extend wireless network of what router. This will only work with another Apple router.. the way apple built it is in the family only. So please spell out what is the primary router??
If you did have it working to extend the wireless of a non-apple router in your previous house I simply don't know how.. according to Apple it isn't possible. You can use WDS.. that is slow and reduces everything to G wireless.. that is the only way.
2. When you say in the first post..
4 other devices on my wifi network all have reliable connection, visitors' phones and laptops too, so shouln't be a wifi netowrk issue, ie network outside TC.
I presume if you turn off the TC, these devices still have wireless network because they are connected to the primary router.. not the TC.. again my bad reading.. I assumed they are connected to the TC.
So please spell out the whole network..
Broadband modem.. type, model, make.
Main router.. type model make
Any other network devices.
And how was it setup in your old place and how is it different now.

My Time Machine does not recognize Airport Time Capsule 2TB

I just connect my new Airport Time capsule 2TB and the wifi work fine in the whole house.
But Time machine does not recognize my Airport time capsule. It remain stuck on my ex baxkup My Book. If I press select disk or option nothing happen . If I click on remove backup disk nothing happen. I want to use Airport Time capsule as my back up disk.
Thank you for your help.
Guy-Gabriel

Do a full TM reset.. see A4 here.
http://pondini.org/TM/Troubleshooting.html
You might also need to manually mount the TC disk..
In finder use Go, Connect to server in the top menu.
AFP://TCname or TCIPaddress (using the actual name or IP of course).

I have just got an Airport time Capsule for back up how do I do it? Do I put the ethernet cable into the back of my sky hub because when I do that the amber light on my Time Capsule flashes amber. Please talk in simple terms as I am a

I have just got an Apple Airport time capsule to back up my one year old iMac......how do I do it? I have tried putting an ethernet cable into the time capsule and to my sky hub, all I get is a flashing amber light, can anyone help I am a silver surfer not used to Apple products, but love them, plus I don't understand half of the jargon....HELP please

Apple's Setup Guide for the Time Capsule is pretty simple and clear for most users, and you don't indicate at what point or step that you are getting stuck.
So, please go to page 8 in your Setup Guide to review the topic of Plugging In Your AirPort Time Capsule.
The Sky hub will likely have 4 Ethernet <--> ports on the back of the device. Pick any one that you want and connect one end of the Ethernet cable to the port that you choose.
Then, connect the other end of the Ethernet cable to the WAN (circle of dots) port as shown in the Setup Guide.
Continuing with the instructions on page 8 of the Setup Guide, power up the Time Capsule by connecting the power cord from the back of the Time Capsule to a wall AC jack.
Note that the instructions indicate that the indicator light will be solid amber during startup, and it will change to blinking amber during the setup. The light will remain blinking amber until you have configured the Time Capsule at which time the light will turn green.
Next, go to page 12 of the Setup Guide to see the information to Use your Mac or iOS device to set up your AirPort Time Capsule.
You indicated in your tag line that you were using OS X Mountain Lion (10.8.3), and since that will exceed the minimum requirement of a Mac using OS X (10.7.5) as noted in the guide, you can use your Mac to set up the Time Capsule.
Continuing with the instructions on page 12 of the Setup Guide......
1. Open AirPort Utility on your Mac. It is located as follows: Finder (the smiley face on the dock) > Applications > Utilities > AirPort Utility
2. Select your AirPort Time Capsule and click Continue. You won't be able to do this, but read further......If you do not see the AirPort Time Capsule that you want to configure, choose it from the WiFi status menu in the menu bar, at the top of the screen.
So, clicking on the WiFi icon will yield a small window that looks like this:
The example below shows an AirPort Extreme. You will see Time Capsule on your screen. Click on Time Capsule.
When you click on Time Capsule, that will get the setup wizard going. it will take a minute to analyze the network, then display a screen that looks similar to the illustration below, except that you will see a picture of a Time Capsule on your screen
3. Continuing with the Setup Guide.......Follow the onscreen prompts to create a new network
Network Name...........Type in a simple name that you want to call your network. Do not use the suggested name.
Base Station Name....Type in a simple name that you want to call the Time Capsule. Mine is TC, for example.
Password...................Type in a password that will be used for both the network and the Time Capsule. Write that down.
Verify..........................Type in the password again to Verify
Click Next
The setup wizard will configure everything for you. When you see the message of Setup Complete, click Done.
The Time Capsule is now set up and it will display a green light.

AirPort time capsule, remote access?

I can not acess my AirPort time capsule from outside home network. It works perfectly inside the home network, but is not accessable remotly (From outside my home net) I can see the time capsule as a shared unit in finder, and the cloud is turned on, but I can still not open th disk from outside home. Every unit is up to date!
Can any please help me!

Between the internet modem and APTC there is also a router. (All the items are wired)
I can see the APTC from the outside world, but can not access it.
Use the method of AFP port forwarding.
This is simple.. the TC must be in bridge..
Map port 548 TCP to the TC.. and ensure the TC is static IP so the port forward is always correct.
Then from the other site you simply access it via AFP.. in Finder go, connect to server, type
AFP://PublicIPaddress
Remember the security here is important so use a decent length disk password.
Read https://discussions.apple.com/docs/DOC-3413
Method 3 for more details.

Printer not working via usb connection to airport time capsule

I bought an airport time capsule 3 TB, and I wanted to connect my multifunctional printer-scaner "canon i-sensys MF4350d" via usb to my airport device.However, I found a problem. Although my printer working properly in direct connection via usb,not working when connected via usb to my airport time capsule. when I chose printer In nearby printer list this error apeared:"the software for this printer is currently unavailable please contact the manufacturer for latest version" when I chose add printer and chose the printer model this error apeared:"the printer information has not been acquired"
devices:
printer: canon i-sensys MF4350d
air port time capsule 3 TB
macbook pro me664
osx mountain lion 10.8.5 (latest version)
printer software:canon UFR II ver 2.43(latest version for my printer)

Login to airport utility via Mac or windows pc. Look under connected usb devices and it should say your manufacturer for the printer. If not try rebooting both printer and router with them being plugged in or try different usb cable or port on printer.

How can I print via the AirPort Time Capsule on a Windows 7?

Hey,
First of all, I am really inexperienced about all these things. I have a MacBook from 2009 with OSX Lion and a PC Windows 7 x64. I have got a time capsule (https://www.mikepalmer.net/wp-content/uploads/2011/12/apple-time-capsule.jpg) connected to my router
and then another router in my room (probably working as an acces point) to which I wirelessly connect my Windows 7.
The thing is that I can see the printer (HP Laserjet P1005) from my Mac but I don't know how to add it to my windows. On a previous PC I added a printer to the time capsule's IP 192.168.1.2 and printed with a considerable delay that way.
As you can see I don't understand how networks work, how IP's work, or how ports work in this matter.
Any help will be much appreciated!!

Hi PGMLEBL,
I am not familiar with Mac product, the best way is ask the HP printer support for the detail support, generally if we know the printer IP address we can add it through add
a network printer, you may can refer the following third party article to add the printer:
how to install a network printer using TCP/IP in Windows 7
http://www.jmu.edu/computing/helpdesk/selfhelp/win7tcpipprinting.shtml
I’m glad to be of help to you!
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Airport (TIme Capsule) not connecting to iMAC running windows XP

I have an iMAC that runs both OS X and Windows. My router is an airport (Time Capsule)
I can wirelessly access the router when running OS X, but when I run Windows XP I can not. If I plug the cable from the cable modem directly into the iMAC when running XP, it works fine.
The airport (Time Capsule) shows up in the wireless setting with a strong signal, but when I try to connect to it; I get "Wireless router is out of range". The airport sits next to the computer.
Any suggestions.
Mac

What type of radio mode and encryption are you using?
Are you using 802.11n 5GHz mode for example?
iFelix

WiFi Printer not being found on AirPort Time Capsule

Hi, I have an older HP Officejet 6500 that works fine via WiFi. I recently bought an Airport Time Capsule for Time Machine backups and a better wireless router (version is 7.7.3).
Suddenly, my WiFi HP printer, which is connected to the Airport Wireless Router, can't be found by any of my macs, iPhones, or iPads. I had no problem printing from any of these devices when the printer was connected to my previous wireless router.
I've searched and searched this evening for help and can't find any solutions. I've tried resetting, checking for firmware upgrades, unplugging the printer and router. No luck so far.
Thanks in advance for your help!
Desperate in Texas!!!

I suggest deleting your existing printer from System Preferences > Printers & Scanners, and adding it again. Better yet is to "reset the printing system" as described here: Mac OS X: How to reset the printing system
After you do that you will need to add the printer again according to the instructions here:
OS X Yosemite: Add or remove a printer

Airport time capsule won't allow me to print over wifi

I just bought an airport time capsule 2TB. I set it up and almost everything works great. I have a printer that is not wireless. It's a brother 7065DN. I was told by an apple employee that if I plug the printer into the airport time capsule it will allow me to print wirelessly from my macbook pro. However, this does not work. I'm not that big into technology but if anyone knows how I can fix this please let me know. It would be nice not to have to plug my laptop in all the time to print a short

You do it the same way you did when you installed the printer on your Mac.
Connect the printer to the USB port on the Time Capsule
Power up the printer
Click System Preferences (gear icon on the dock)
Click Print & Fax
Click the + (plus) button at the bottom of the printer list
Hopefully, your printer will appear.... IF......it is compatible with the TIme Capsule
Click on the name of the printer to highlight it
Click Add
Now try to print. When you open the Print dialog box, it will appear as if you have two printers installed......because you do. One is installed on the Mac. The other is installed on the Time Capsule
You must choose the correct printer at the Time Capsule to be able to send the print command to the printer at the Time Capsule.

Windows 8 not printing on Airport Time Capsule

Similar Messages

Maybe you are looking for