Windows 8 Problems with Airport/Airtunes

Installed Windows 8 from Windows 7, reinstalled latest version of iTunes and Airport Utility. iTunes now no longer "sees" Airtunes speakers (connected through multiple Airport Express units throughout house). Speakers are seen by all Apple devices (Mac, iPhones), so I know they are connected.
Also, when I run Airport Utility, it doesn't discover the Airport Extreme basestation, and it doesn't show any of the Airport Express units.
Any ideas? Is Airtunes just not supported on Windows 8 yet?
I tried repairing Bonjour in installed applications interface, no luck.

Apple does not yet provide any support for Win8 which means there are no drivers for Win8 which is why you don't have any wireless support for Win8. I suggest that if you wish to run Windows you revert to Win7.

Similar Messages

Problems with Airport setup after buying Version 7 models, (older ones will not upgrade)

Problems with Airport setup after buying Version 7 models, (older ones will not upgrade)
I re set up my Airport network , having had 4 expresses for years doing a good job. I bought another and an express, but then a time capsule after my external drive died. .Problems with Airport setup after buying Version 7 models, (older ones will not upgrade)
I moved house and have fibre network so 38mb/s - they all look ok on the utility, but its not till I saw the App version that they are not compatible as mac will not upgrade the version 6 ones, leaving me with 2 disjointed networks and 7 appliances, 4 of the old , 3 of the new.
my new house is expansive so i wanted the extended range and airplay in each room.
This is not told to customers, and utility doesnt show any issues.
I do not seem to get any range from either network now, - and I'm quite experienced with airport (6 yrs of setting up & using & extending)
Any advice ?
LJx
Message was edited by: LJLDN
Message was edited by: LJLDN

Sorry couldn't change the detonations to Airport and am new so cant delete!

HT1218 why is streaming to my TV slowing to .4 mbps from 8.ombps while watching a netflix movie? this has become a problem in the last 2 months. This also happens on another TV but not concurrently.. Is it a problem with "airport extreme" or with the IP s

why is streaming to my sony TV slowing to .4 mbps from 8.ombps while watching a netflix movie? this has become a problem in the last 2 months. This also happens on another TV but not concurrently.. Is it a problem with "airport extreme" or with the IP service? Airport extreme software is up to date.
please advise
Michaelgfrommet

For what it's worth, you posted this in 2011, and here in 2014 I am still having this same issue. Over the last two days, I have had to unlock my apple account 8 times. I didn't get any new devices. I haven't initiated a password reset. I didn't forget my password. I set up two factor authentication and have been able to do the unlocking with the key and using a code sent to one of my devices.
That all works.
It's this having to unlock my account every time I go to use any of my devices. And I have many: iMac, iPad, iPad2, iPad mini, iPhone 5s, iPod touch (daughter), and my old iPhone 4 being used as an ipod touch now. They are all synced, and all was working just fine.
I have initiated an incident with Apple (again) but I know they are just going to suggest I change my Apple ID. It's a simple one, and one that I am sure others think is theirs. I don't want to change it. I shouldn't have to. Apple should be able to tell me who is trying to use it, or at least from where.
Thanks for listening,
Melissa

Problem with Airport express N (2nd gen)

Problem with Airport express N (2nd gen)
Firmware 7.6.4
ISP - 20 Mbps ethernet cable
I have MacBook Air 13 mid 2013 os x 10.9.5, ipad 4 ios 8.0.2, ipad4 ios 7.1.2 , iphone 5 ios 7.1.1
When i try to use speedtest.net from my Macbook i got good results of download speed and incredible upload http://www.speedtest.net/my-result/3801286946 (connection 300 Mbps) , both ipads got terrible speedtest download result and incredible uploadhttp://www.speedtest.net/my-result/i/981631804 (connection 150 Mbps), iphone 5 got bad download and great uploadhttp://www.speedtest.net/my-result/i/981695357.
All these tests were done near airport express with really good signal and 5ghz. I tried to choose different channels, 802.11 mode, guest ssid, 5ghz ssid ...
I think that something is wrong with my new airport express. Can anyone help me to solve this problem?
ps sorry for my bad english

As a last resort, try a factory default reset on the AirPort Express as follows:
Power off the AirPort Express
Wait a minute
Hold in the reset button first, and keep holding it in for another 8-10 seconds while you simultaneously plug the Express back in to power
Release the reset button after the hold period and allow a full minute for the Express to restart to a slow, blinking amber light status
On an iPhone or iPad home screen....
Tap Settings
Tap WiFi
Look for a heading of Setup a New AirPort Base Station. If it appears.....
Tap on AirPort Express just below the heading to start the configuration process on the Express again
If you try several factory default resets, and the AirPort Express does not appear under the heading of Setup a New AirPort Base Station, the Express most likely is defective and will need to be replaced.

Problems with AirPort and WPA access point

Okay, I have done quite a bit of research and I still cannot resolve my problem because of this, I am turning to this user community.
Here is what I know as of right now:
I am running Windows OS X 10.4.4 with AirPort Update 2005-001. My Access Point is a 3COM 8250.
The AP is setup not to broadcast its SSID, to use WPA-TKIP (or in Apple terminology, WPA Personal) and the password is set to use alphanumeric.
When I try to connect my PowerBook with the SSID name, WPA Personal and the correct password, I get the following error:
The password you entered is not correct for the Airport network *******.
To troubleshoot here are the test I have run and their outcomes:
Test
- Result
Set the AP to completely open
- Connected
Set the AP to open, didn't broadcast the SSID
- Connected
Set the AP to WEP, broadcast the SSID
- Connected
Set the AP to WEP, didn't broadcast the SSID
- Connected
Set the AP to WPA & WEP, broadcast the SSID
- WEP : Connected
- WPA : Not Connected
Set the AP to WPA & WEP, didn't broadcast SSID
- WEP:Connected
- WPA:Not Connected
Set the AP to WPA only
- Not Connected.
Now, I should mention that when I was running 10.3.3 I could not connect either. The AP is running the newest firmware and I have three Windows XP SP2 laptops / workstations that can connect with no problems.
I have tried to find a compatibility matrix on both 3COM's and Apple's websites to see if it might be a compatibility issue but I have not been able to find one on either site.
Any help that anyone could provide would be greatly appreciate.
Thanks in advance.
17" PowerBook G4 Mac OS X (10.4.4)

Hello MisssAsh. Welcome to the Apple Discussions!
It's always a good idea to do a complete power recycle when changing network configurations.
Try the following, in order, checking for Internet access after each step, until resolved:
1. If the modem has a reset switch, use it to reset the modem. Wait at least 5-10 minutes for the modem to initialize.
2. Remove power from the modem. If it has a backup battery, remove this as well. Wait 5-10 minutes. Replace the battery, and add power back to the modem.
3. Perform a complete power recycle of your network components as follows:
Modem/Router Power Recycling - Quick
o Power-off the modem, AirPort Express Base Station (AX), & computer(s); Wait at least 5 minutes.
o Power-on the modem; Wait at least 5 minutes.
o Power-on the AX; Wait at least 5 minutes.
o Power-on the computer(s)
If this fails to get the modem to "recognize" the Internet router, then try the "Full" version.
Modem/Router Power ReCycling - Full
o Power-off the modem, AX, & computer(s). (Wait at least 30 minutes. If possible, leave the modem off overnight.)
o Power-on the modem; Wait at least 15 minutes.
o Power-on the AX; Wait at least 5 minutes.
o Power-on the computer(s)
4. Contact your ISP to have them perform a "modem reset."

Timecapsule and iMac Early 2008 - Problems with Airport Utility

I have bought a new iMac and a TimeCapsule. With *Leopard 10.5.5* i have some problems to change the configuration. The Assistant will not work. The changed settings will not send to theTime Capsule (Ethernet or and Wireless). The airport signal is _very low_ under OSX (-60 — -64 dB). When I use airport with Windows XP on Bootcamp partition it will work fine. No problems with changing settings and the signal is -1 db.
Who has the same problems or can help me!

Do the black bars drop also at these times?
Make a New Location, Using network locations in Mac OS X ...
http://support.apple.com/kb/HT2712

Big problem with Airport Extreme and Vivax Provider in Brazil

Hello guys.
I live in Brazil and I bought my Airport Extreme in a recent trip to USA.
For some years I was a client of Telefonica and had an ADSL link, I had a D'Link G604T to do both the modem and router operation in the same box. I was happy with my connection of 1Mbps.
In a recent promotion of Vivax I switched to a cable connection to have both TV and Internet at the same operator, my link now has 3Mbps.
With this pack I also received free one RCA cable modem model DCM425B, it was installed fine in one computer only. Everything was fine my connection was faster the old one.
So I went to install the Airport Extreme to make things even better.
After I installed I went to see the web status of my modem, all parts were looking fine, but the modem could not see the computer. Bad sign.
I talked to Vivax support people and apparently it was a problem with their network setup and they manage to make it right. My model now sees my computer.
After that problem was solved I could not make AE to work with the modem, it had the green light and the setup looked fine, but I could not open any site. I tried to turn off my modem and AE, waited some minutes and turned on first my modem and after it was up I turned on AE. All lights looked fine but again no connection to any site.
I called again the Vivax support center and they tried to help me but the don't know AE and they could not help me with all the details but said there was 2 10.x.x.x coming from my side. So I tried to use in bridge mode. I also selected the 192.x.x.x range instead of 10.x.x.x as default.
After many setups and turn off and on again my connection is working but I have a big problem with wireless. If I turn it on I loose my connection, it seems that AE sends 2 equal ethernet address to Vivax and their network don't like it cutting me off.
So my connection setup is like this:
RCA Cable modem model DCM425B at 3Mbps using a 200.x.x.x ip
Airport Extreme connected to a Mac and a Windows PC by wire using the 192.x.x.x range ip
Wireless is off
Bridge mode is on
This the only way I could make it work.

After a firmware update it worked fine.

An irritating problem with AirPort

Hi,
I've read a few forums addressing this issue but none of the proposed solutions have worked for me.
I am currently running a MacBook Pro on Snow Leopard (10.6.4) and my internet connection has just died. I tried unplugging the router, turning on/off AirPort and rebooting, attempting to renew the DHCP lease, but the problem still remains - AirPort has self-assigned an IP address and I am unable to connect to the Internet.
Does anyone know of a solution to this problem? I would greatly appreciate your help.
MANY, MANY THANKS.

OK, so I would check whether your computer works with your router when it is using the Ethernet connection, and I would check whether it works wirelessly at other wireless hotspot locations other than your home.
If this were my problem, that would guide me in deciding whether it is a hardware problem with the wireless or maybe a configuration problem such as MAC authentication in the router preventing affiliation or incompatible wireless protocols.
That new piece of information now confuses me about what exactly is your network topology. So are you running BootCamp on this computer and you can connect to the internet in the Windows boot camp partition but can't connect to the internet in the Apple partition? Or vice versa? Or none of the above? What is "excellent?" Full bars in the signal strength indicators? What computers/OSs are getting onto the internet for you, and what ones aren't?

Problems with Airport Card

I move back and forth from school to home, and I've never had a problem with my card before. I recently restored my compuer back to its factory settings, and it was running great with my Airport Express. I came home after moving, and my computer won't read the WPA hooked up in my house. It says I am connected, but won't let me access the internet. I'm not sure why. We tried rebooting the connection, I've looked on my computer, used system preferences and everything. I did notice when I tried to use the Network Setup Assistant, it said the password I used to connect was wrong, but when my computer uses the airport icon at the corner of the screen, it accepts the password. Any ideas on how to fix this?
iBook G4 Mac OS X (10.3.9)

An additional distressing note -- I went back to aforementioned building with the 10.4.5 Powerbook last night. Did a cold boot...and the Airport Express picked up the correct network DHCP info immediately. Roamed between a couple of WAPs, surfed a couple of sites, then sat down and tried to duplicate this feat...by re-booting at least 6 more times. Nada. I once again got factory default IP addresses on each attempted reboot. I changed nothing from the network settings I'd tried last week with this machine nor were any changes made to the network or WAPs. DHCP didn't work last week on several attempts (and reboots), worked ONCE yesterday on the first boot, then nothing again on the subsequent reboots.
Again, I'm stressing that there don't "seem" to be problems with the network or WAPs because Windows clients consistently obtain DHCP and authenticate without issue.
Does anyone have any ideas?

Problems with Airport Express

Sunday morning blues!! For some reason when I connect to my airport express it disables my internet access....??? I am using a speedtouch USB modem and connecting to the internet via Virgin broadband. With Airport switched off Safari works fine, as soon as I connect to the express the internet connection is lost and safari directs me to the network diagnostics utility, which just tells me that the network connection and the airport connection have both failed. Can anybody help??

Sunday morning blues!! For some reason when I connect
to my airport express it disables my internet
access....???
The problem you have is that you can't have two network connections (the USB one and the Airport) active at the same time.
Can anybody help??
The solution though is as follows.
System Preferences > Sharing > Internet
Share your USB internet connection via Airport.
This configures the Mac as a software base station.
Re-configure the Airport Express as a client for this Mac based wireless network.
You will then have an active internet connection and be able to print wirelessly and use AirTunes.
Personally I would recommend you replace your USB modem with an ethernet (wireless) modem instead.
Check out the following website.
Reviews of equipment
http://www.adslguide.org.uk/reviews/
I would also check out ADSL Nation's X-Modem M3 http://www.adslnation.com/products/xmodem-m3.php It is also now available from the UK Apple store and retail stores.
http://store.apple.com/Apple/WebObjects/ukstore?productLearnMore=TJ151
which can also be used in conjunction with an AEBS or AX.
iFelix

Is there a software problem with Airport Extremes?

I recently bought a new 802.11ac next generation AE to replace my old generation AE mainly for the increased wifi speeds. I have been having trouble though getting my proper wired speed using the router though. I didn't have problems with the previous version in the past. But now using the new one I get low speeds at times, but its not constant. I have comcast and get 60 mbps speeds when hooked up straight to my PC. Using the AE, at times I get the same speeds, but usually now it drops all the way to like 12 mbps. I don't understand what it is, and thought about returning the AE but I have past my purchase time to return. The other night I used speedtest.net and I got 12 mbps. So I unplugged the comcast modem and restarted everything and it went back up to 60 mbps. But it seems to drop down to 12 constantly. I tried the same process last night, and it did not return to 60 mbps, it stayed at 12. So I still have my old AE, and hooked that up figuring I would not have the same issue. Yet I totally did. 12 mbps again. So is this some sort of software issue that is making this happen, I don't understand it. I see people having trouble with WiFi speeds on here, but this is a wired connection. I also thought I would test the wifi for the heck of it while I was getting 12 mbps wired through my AE. So I used my phone connected to wifi and ran speedtest, and I got 23. So how can my wifi speed get higher returns than my wired connection? Can anyone help?
Thanks,
Eddie

I'm having a similar issue. I have TWC turbo cable in Manhattan. I get 20Mbps download speed when I connect a Mac directly to the modem via ethernet. When I use the current gen AirPort Extreme, my internet speed gradually decreases to unusable. Less than 1Mbps. Websites timeout before loading. My LAN still works, but internet crawls. Doesn't matter if a device is wired directly to Airport or wirelessly connected - internet crawls, if I'm lucky.
This is after weeks of things running perfectly with this airport. Over the past few days, I'm dying.
I spent time with TWC to make sure it wasn't on their end. Reset the modem. Ran signal tests. Rebooted everything. It's not an issue on their end. As soon as I plug directly into their arris modem, I'm golden. 20Mbps download again.
I hard reset my AirPort Extreme, and set it up as if it was brand new. But internet speeds still drop to slow to unusable when I'm going through AirPort Extreme.
Had some luck getting speeds up to usable by specifying DNS servers from TWC in airport, but this was false hope. Overnight, internet speeds were back down to less than 1Mbps.
Again, if I connect a mac directly to the modem, I'm getting 20Mbps speeds again, as I should.

MBP 5.1 I have a recent problem with airport connectivity. ethernet connection is working fine, but wifi has become extremely slow and bad functioning. signal is received, no problem with the wlan (my husband 's wifi with MBP is perfect) please help

I have a MBP 5.1 with snow leopard 10.6.8. It has been working fine until few days ago, when it started to have different problems:
1) airport is not working well. it is extremely slow, has difficulties in fully loading pages, looses connectivity, It is not browser related, behaves thesame in safari or firefox; it is not the router/wlan; my husband mbp wifi works fine (as it was mine...) and iphone wifi is also working fine. it sees the signal and different networks. , it is also very very slow in opening skype (after that, it is working ok) if I connect via ethernet cable to the same router, everything works perfectly and with the correct speed.could it be a damaged airport card? a software problem/corruption? logic board? (I hope not, the computer is out of apple care now....)
2) after a certain time (more than hours) of use, the trackpad is behaving strangly, increase sensitivity to touch, unwanted selection of folders, files and text or images in web pages when i move the cursor, the cursor jumping all over the places while writing, ecc I have the impression it starts doing that when I use heavily the CPU ( and the temperature goes up). Is this again a problem of the mother/logic board?
I had recently serviced it since it was not booting properly, but except some permissions repaired, they did noit find anything wrong in the hard drive (which I have now substituted with a SSD) or other hardware.
thanks in advance for any help/suggestions
alessandra

I think I solved the wifi connection problem, just by switching off completely the router! sounds trivial, but in this case it worked!!!
the funny behaviour of the trackpad/cursor still persists. any suggestion???
thanks again

HP Color Laserjet 3600 Printing Problems with Airport Extreme & JetDirect

I have a HP Laserjet 3600n connected via ethernet cable to our Airport Extreme base station using the built-in JetDirect functionality of the printer. Prior to installing Snow Leopard we had no problems and every computer on the home network could see and print with full functionality on the printer.
After installing Snow Leopard, it took a while but I got the printer working again with the same setup. Then we had a power outage and the printer was no longer visible on the network or in the airport settings. Again it took a while but I once again got it to work. But now it seems like it keeps falling off the network and the printer itself either shows an IP address of 0.0.0.0 or another random one. The IP address should be generated by DHCP by the airport.
I don't know if this is a problem with Snow Leopard, the airport extreme, or the printer. The way I got it to work the last couple times no longer fixes the problem. Someone please help.
Message was edited by: balistikboy

I don't know if this is related, but...
My MacBook Pro (Airport) has always been dicey connecting to an HP LaserJet 4000 on my wired LAN. Before Snow Leopard, I used AppleTalk rather than IP printing because it just worked.
But Snow Leopard doesn't support AppleTalk any more, so I reinstalled the printer to connect via JetDirect (which supposedly provides more features). When it works, it works fine. But very often I get a message that it can't connect to the printer. The only thing I've found that fixes the problem is power-cycling the printer, which somehow enables queued jobs to print. Needless to say, this gets old.
Is there some trick I'm missing?

Printing problem with Airport printer

Hi,
I am having problems getting my daughter's G4 Macbook to print with Airport Extreme. The history is:
1. Set up my iMac, Airport Extreme, all well, both G4 and iMac fine over wireless.
2. Added HP Photosmart 8150 to Airport. Worked fine for iMac
3. Added it to Macbook, no go
4. Discovered that I had not actually added it to Macbook. At some point in the past, to allow printing for my daughter we had done a direct USB connection for her, and it was that we were trying to print to. But, it was there via Bonjour as a third printer when I looked.
5. Tested it from the MacBook. Graphic fine, but no text. However, v. pushed for time so no further testing.
6. Daughter tested, no good
7. Looked at all 3 printers on Macbook. 2 x USB (1 8150 plus one other from her University), plus the Bonjour 8150.
8. Decided that installing the same printer twice might be a problem. So deleted all three.
9. Now I can't install. When I go to add a printer the Macbook can't see any. Have downloaded drivers, but to no avail. Have tried as many combinations as I can in drop downs.
Basic Airport connectivity for the G4 is fine - internet functions no problems, no dropped connection etc.
Any thoughts? I am a Mac newcomer, ex PCs, pretty techno-literate.
p.s. Have reset print queues etc

Airport Extreme unit failed - replacement cured all problems

Install of apps 11.5.8 on Windows - Problems with PreReqs

Hello all,
I've worked with Oracle database server for years,
and installed it many times. I want to learn Oracle apps,
and I'm attempting the install of 11.5.8 on Windows
from the CDs. But I'm having some problems with the
pre requisites.
Unlike LInux, if the install doesn't work, you can't
clean out all traces of the install. I've completely
reinstalled Windows to start fresh this last time.
Although, with the pre req warnings, I didn't attempt
the install.
Here is what I did.
Copy the CDs.
Rapidwiz
install Oracle apps
Single Node
TEST. Fresh database.
Component apps licensing
Choose all of:
Marketing
Sales
Order Management
Financials
no particular country
WE8ISO8859P1 - Western European
- for database, and appl_top character set.
The computer name is called Green.
C:\OAppsInstall\redCD\Disk1\rapidwiz>ping green
Pinging green [127.0.0.1] with 32 bytes of data:
Set
appl_top
c:\oapps11\testappl
common_top
c:\oapps11\testcomm
etc.
NTUSER:               oracleapps
pw:               ???
DNS Domain Name:     green
These next directories are default, but do not exist:
MKS Directory          C:\mksnt
MSDEV Directory          C:\VC98
External JDK          C:\java\jdk1.3.1
OUI Inventory Path     c:\Program Files\Oracle\Inventory
It does a port availability check.
- the ports are all fine.
And checks the pre-requisites.
These three have problems:
Host/Domain Check
running command : ping -n 1 localhost
Pinging green [127.0.0.1] with 32 bytes of data:
Reply from 127.0.0.1: bytes=32 time<1ms TTL=128
Ping statistics for 127.0.0.1:
Packets: Sent = 1, Received = 1, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 0ms, Maximum = 0ms, Average = 0ms
host ping has suceeded
running command : ping -n 1 localhost.green
Ping request could not find host localhost.green. Please check the name and try again.
Error - host.domain ping has returned an error: 1
System variable PATH set to:
.COM;.EXE;.BAT;.CMD;.VBS;.VBE;.JS;.JSE;.WSF;.WSH
System Utilities Check
running command : cmd.exe /c C:\OAppsInstall\redCD\Disk1\rapidwiz\bin\checkutil.cmd C:\mksnt C:\VC98
C:\OAppsInstall\redCD\Disk1\rapidwiz>echo off
'which' command is not available. Check MKS installation.
ERRORCODE = 1 ERRORCODE_END
Error - System Utilities Availability test has returned an error: 1
JDK Availability Check
running command : CheckerClass.JDKCheck()
JDK Directory Does not exist, Input was - C:\java\jdk1.3.1
Error - JDK Availability Test has returned an error: 1
I check the PDF install doc:
Step 2: Install Latest Java Development Kit (JDK)This release of Oracle Applications requires Java Development Kit (JDK) 1.3 or
higher. Before you begin your installation, download and install the latest version of
JDK on your concurrent server, administration server, forms server, and web server.
Download JDK 1.3 from the download site for the operating system where you will
deploy the Oracle HTTP server. See OracleMetaLink document 130091.1 (Upgrading
to JDK 1.3 with Oracle Applications 11i) for a list of the sites.
1. Follow the installation instructions provided with the download.
2. Make a note of the location where you install JDK. The Rapid Install wizard
asks for this location on the Derived Settings screen. (See Step 8 on page 2-14 or
Step 9 on page 3-16.)
MSDEV Directory (Windows)
Location of the Visual C/C++ executables and .DLL files. Used for linking application executables or .DLLs.
MKS Directory (Windows) MKS tools must be added in the PATH so that executables can be used to
relink application executables and .DLLs.Finally the Questions:
I've been looking at other threads.
Oracle E-Business Suite R12 Installation Steps on Windows XP
1)
For this older 11.5.8 version, do I need to install the JDK, or will
this be done for me? If I do need to install the JDK, can I use the
latest version??
2)
Do I really need to install MS Visual C++ ?????
If so, could I use the latest .NET express instead??
3)
What is the MKS? The one thing the docs say is:
MKS Directory (Windows) MKS tools must be added in the PATH so that executables can be used to
relink application executables and .DLLs.Do I just need to create an "MKS" directory, and add it to the path?
Or, do I need to install some other software??
I've tried installing this a few times over the past few years, and
while I've had different levels of success, I've always had some kind
of issue after the install was done.
I really want to learn form and reports, so I hope that you guys
can help me out on this so I finally get a clean install.
Thanks a lot!

Thanks.
Ok, I bought VC++ and installed it.
And, installed: j2sdk1.4.2_10
I could:
C:\> copy gawk.exe awk.exe (answer yes to copy over existing file)
C:\> copy grep.exe egrep.exe
However, I couldn't:
C:\> copy make.exe gnumake.exe
C:\> copy gcc.exe cc.exe
- because there are no such files in cygwin.
$ pwd
/usr
$ find . -type f 2>/dev/null | grep -i gcc
- nothing
$ apropos make
indxbib (1) - make inverted index for bibliographic databases
ln (1) - make links between files
makeinfo (1) - translate Texinfo documents
makewhatis (8) - Create the whatis database
mkdir (1) - make directories
mkfifo (1) - make FIFOs (named pipes)
mknod (1) - make block or character special files
mktemp (1) - make temporary filename (unique)
OracleApps@green /usr
$ find . -type f 2>/dev/null | grep -i make
./bin/makeinfo.exe
./sbin/makewhatis
./share/groff/1.18.1/font/devdvi/generate/Makefile
./share/groff/1.18.1/font/devlj4/generate/Makefile
./share/groff/1.18.1/font/devps/generate/Makefile
./share/man/el/man8/makewhatis.8
./share/man/it/man8/makewhatis.8
./share/man/man1/makeinfo.1
./share/man/man8/makewhatis.8
./share/man/ro/man8/makewhatis.8
System Utilities Check
running command : cmd.exe /c C:\OAppsInstall\redCD\Disk1\rapidwiz\bin\checkutil.cmd C:\cygwin\bin "C:\Program Files\Microsoft Visual Studio\Common\MSDev98\Bin"
C:\OAppsInstall\redCD\Disk1\rapidwiz>echo off
'which' command is available.
'gnumake' is not available.
ERRORCODE = 1 ERRORCODE_END
Error - System Utilities Availability test has returned an error: 1
Where do I get gcc and make from??
Thanks a lot!

Windows 8 Problems with Airport/Airtunes

Similar Messages

Maybe you are looking for