Windows cannot conects .. name

Does anyone know what I should do?
I just bought my Vista machine and new router . I successfuly installed everything my laptop works fine for about 3months everything was fine i was using wi fi but later on my laptop starts to disconect from my internet and later it find the internet but says that windows cannot conect to name i got internet on my laptop by the cable i buy new internet card but its still the same i reinstal my windows and nothing i now got the windows that i have at the begining i got internet from virgin

So when you Hardwired your computer to the Router you are able to access Internet on your Computer... But when you try to connect to your Wireless Network you are getting an error message "Windows Cannot Connect to the Selected Network".. If you are getting this error message then you need to change the Wireless Settings of your Router..
Whats the Model number of your Router? Assuming you have N Series Router, Here are some of the Settings which you need to change it on your Router.
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1 and press Enter...Leave Username blank & in Password use admin in lower case...
For Wireless Settings, please do the following : -
Click on the Wireless tab
- Here select manual configuration...Wireless Network mode should be mixed...
- Provide a unique name in the Wireless Network Name (SSID) box in order to differentiate your network from your neighbours network...
- Set the Radio Band to Standard-20MHz and change the Standard channel to 11-2.462GHz...Wireless SSID broadcast should be Enabled and then click on Save Settings...
Please make a note of Wireless Network Name (SSID) as this is the Network Identifier...
For Wireless Security : -
Click on the Sub tab under Wireless > Wireless Security...
Change the Wireless security mode to WPA, For Encryption, select TKIP...For Passphrase input your desired WPA Key. For example , MySecretKey , This will serve as your network key whenever you connect to your wireless network. Do NOT give this key to anyone and remember the key.
NOTE : Passphrase should be more that 8 characters...
Click on Wireless MAC Filter : -
Make sure the Wireless MAC filter on your Router is Disable.
Now see if you can locate your Wireless Network and attempt to connect....

Similar Messages

I keep getting the message, "Windows cannot find 'c:\Program Files (x86)\Mozilla Firefox\firefox.exe'. Make sure you typed the name correctly, and then try again." I get it when I either try to open it from the Start menu or from the desktop icon.

I've just installed Firefox on my laptop and keep getting the message, "Windows cannot find 'c:\Program Files (x86)\Mozilla Firefox\firefox.exe'. Make sure you typed the name correctly, and then try again." I get this message whenever I either try to open it from the Start menu or from the desktop icon. I've never gotten it to work and even uninstalled it and then redownloaded it and still cannot get it to open. Any help would be greatly appreciated!!!!

Are you installing from the official site? http://www.mozilla.com/firefox
If you use Windows Explorer (My Computer) to check that path, is the Mozilla Firefox folder there? That is the normal installation location, but I think it's worth checking.
If the folder isn't there or firefox.exe is not in it, I wonder whether some other software might be interfering. You might want to run some supplemental security scans. These two tools are highly regarded:
Malwarebytes Anti-malware : http://www.malwarebytes.org/products/malwarebytes_free
SUPERAntiSpyware : http://www.superantispyware.com/

Windows 7 Desktop synchronisation - Windows cannot access \\server\users\name\desktop

Hi there
My client has a laptop which won’t load the desktop when disconnected from the network. When you log on (while disconnected) you get the error
“Windows cannot access \\server\users\name\desktop”
Works as expected while connected to the network.
The server is a Windows Small Business Server 2003 with active directory etc. and roaming profiles turned on. This issue does not occur on other workstations/laptops.
When I check the Users folder on the local system drive there is not a desktop folder. I assume this is the issue although I’m not sure how you would force windows to create one or why one hasn’t been created?
This is a brand new laptop so my initial reaction was to reset the laptop to factory state and then add the laptop back in to the domain. After this process the issue was still present!
I guess the only thing I should mention is that this was shipped as a Home Premium laptop and was then upgraded to Professional using an upgrade key.
I have checked Control Panel, System & Security, System, Advanced, User Profiles and the account shows as Local with Roaming Profiles greyed out.
Any ideas?
Martyn Fewtrell
[email protected]
Martyn Fewtrell TNC (IT Solutions) Ltd Email: [email protected] Web: http://www.tncit.co.uk

Hi,
I am just writing to check the status of this thread. Was the information provided in previous
reply helpful to you? Do you have any further questions or concerns? Please feel free to let us know.
Regards,
Alex Zhao
TechNet Subscriber Support
If you are
TechNet Subscription user and have any feedback on our support quality, please send your feedback
here.
Alex Zhao
TechNet Community Support

"Windows cannot find 'Flash'. Make sure you typed the name correctly, and try again."

I can't open Flash files from Flash Builder 4.6 in Windows 7. I just get this message "Windows cannot find 'Flash'. Make sure you typed the name correctly, and try again."
In Preferences Fila Associations for FLA Adobe Flash Editor (default) is selected as per default initial settings. I've even tried reinstalling FB from scratch and it is still giving this error.

This worked for me (requires Flash install)
In menu bar, select Window->Preferences
In Preferences window, select General->Editors->File Associations
Select or add ".fla" to File Associations
Change the Associated editors to "Flash Document". Set it to "Default"
I also removed their internal "Adobe Flash Editor" since it didn't seem to be working anyway. Not sure if this makes a difference.

"Windows cannot find...Make sure you typed the name correctly" issue across many files

I recently have run into an issue where many programs cannot be opened. I get an error message saying "Windows cannot find... Make sure you typed the name correctly the try again." This happens for task editor, or manage in the control panel. I cannot change settings in the system security as I get the same message.
I ran a full scan of McAfee and nothing was picked up.

Hello,
Thank you for posting in the HP Support Forum.
These symptoms you describe appear because Windows cannot find certain application when it is lauched using some kind of shortcut. Since it appears with many applications (including Task Manager), this is usually considered to be caused by malicious programs (malware) such as viruses, trojans, etc.
http://support.microsoft.com/kb/311446
*Note - the above Microsoft KB article is just one example for the many many viruses that exist out there. Of course, you may
Please, double check your system with other security products aside from your McAfee.
Try to check your computer using the free ESET Online Scananer:
http://kb.eset.com/esetkb/index?page=content&id=SOLN2921&locale=en_US
Scan with the free HitmanPro :
http://www.surfright.nl/en/hitmanpro/
Please, report back your results.
If it happens so that you cannot run ESET or HitmanPro, best would be to use an alternative computer (known clean one), prepare a bootable CD/DVD using a "live" antivirus image such as Kaspersky Rescue Disk or ESET SysRescue Live, and scan your system using this CD/DVD. Full instruction can be found here:
http://malwaretips.com/blogs/how-to-use-kaspersky-rescue-disk/
http://www.eset.com/int/support/sysrescue/
Please, report back your results.
Best wishes,
IT_WinSec
Hewlett-Packard employee | HP Enterprise Services
Although I work for HP, I express my personal opinion.
Visit www.hp.com/makeitmatter
--Say "Thanks" by clicking the Kudos Thumb Up in the post that you find useful.
--Please mark the post that solves your problem as "Accepted Solution"

Crashes when running applications from network share - "Windows cannot access the file for one of the following reasons"

Hi,
starting a couple of weeks ago, we get the following error(s) when running applications from a network share. We don't know what causes this, we are not aware of any major changes in our network infrastructure or client/Server configuration. We did upgrade
a lot of machines to Windows 8, but the issue also occurs on older Win7 computers.
We figured out a workaround though: The applications run fine when launching from a FQDN share (like
\\share.domain.Company.com) and only cause problems when running from
\\share directly. They have worked fine for years without FQDN though.
Any ideas?
Error Details (the Kind of error differs greatly):
# 1 #
Log Name: Application
Source: Application Error
Date: ...
Event ID: 1005
Task Category: (100)
Level: Error
Keywords: Classic
User: N/A
Computer: vmDEV
Description:
Windows cannot access the file for one of the following reasons: there is a problem with the network connection, the disk that the file is stored on, or the storage drivers installed on this computer; or the disk is missing. Windows closed the program XYZ
because of this error.
Program: XYZ
File:
The error value is listed in the Additional Data section.
User Action
1. Open the file again. This situation might be a temporary problem that corrects itself when the program runs again.
2. If the file still cannot be accessed and
- It is on the network, your network administrator should verify that there is not a problem with the network and that the server can be contacted.
- It is on a removable disk, for example, a floppy disk or CD-ROM, verify that the disk is fully inserted into the computer.
3. Check and repair the file system by running CHKDSK. To run CHKDSK, click Start, click Run, type CMD, and then click OK. At the command prompt, type CHKDSK /F, and then press ENTER.
4. If the problem persists, restore the file from a backup copy.
5. Determine whether other files on the same disk can be opened. If not, the disk might be damaged. If it is a hard disk, contact your administrator or computer hardware vendor for further assistance.
Additional data
Error value: C000020C [ also seen with code C00000C4]
#2 (German error Messages from now on, we only use German OSes, the above english one is translated based on similar error Messages I found on the web) #
Name der fehlerhaften Anwendung: XYZ.exe, Version: 2015.0.496.5054, Zeitstempel: 0x54ea67c3
Name des fehlerhaften Moduls: clr.dll, Version: 4.0.30319.34014, Zeitstempel: 0x52e0b784
Ausnahmecode: 0xc0000006
Fehleroffset: 0x00026549
ID des fehlerhaften Prozesses: 0x13ac
Startzeit der fehlerhaften Anwendung: 0x01d055a854d36445
Pfad der fehlerhaften Anwendung: \\share\application.exe
Pfad des fehlerhaften Moduls: C:\Windows\Microsoft.NET\Framework\v4.0.30319\clr.dll
Berichtskennung: 949ea933-c19b-11e4-bf04-78542e186754
Vollständiger Name des fehlerhaften Pakets:
Anwendungs-ID, die relativ zum fehlerhaften Paket ist:
Anwendung: XYZ.exe
Frameworkversion: v4.0.30319
Beschreibung: Der Prozess wurde aufgrund einer unbehandelten Ausnahme beendet.
Ausnahmeinformationen: Ausnahmecode c0000006, Ausnahmeadresse 720B6549
Stapel:
# 3 #
Anwendung: WpfApp.exe
Frameworkversion: v4.0.30319
Beschreibung: Der Prozess wurde aufgrund einer unbehandelten Ausnahme beendet.
Ausnahmeinformationen: System.Runtime.InteropServices.SEHException
Stapel:
   bei SP.Forms.AutoCompleteSelectionBase.OnEnter(System.EventArgs)
   bei System.Windows.Forms.Control.NotifyEnter()
   bei System.Windows.Forms.ContainerControl.UpdateFocusedControl()
# 4 #
Anwendung: WpfApp.exe
Frameworkversion: v4.0.30319
Beschreibung: Der Prozess wurde aufgrund einer unbehandelten Ausnahme beendet.
Ausnahmeinformationen: System.Runtime.InteropServices.SEHException
Stapel:
   bei System.IO.UnmanagedMemoryStream.ReadByte()
   bei System.IO.BinaryReader.ReadByte()
   bei System.IO.BinaryReader.Read7BitEncodedInt()
   bei System.Resources.ResourceReader._LoadObjectV2(Int32, System.Resources.ResourceTypeCode ByRef)
   bei System.Resources.ResourceReader.LoadObjectV2(Int32, System.Resources.ResourceTypeCode ByRef)
   bei System.Resources.ResourceReader.LoadObject(Int32, System.Resources.ResourceTypeCode ByRef)
   bei System.Resources.RuntimeResourceSet.GetObject(System.String, Boolean, Boolean)
   bei System.Resources.RuntimeResourceSet.GetObject(System.String, Boolean)
   bei System.Resources.ResourceManager.GetObject(System.String, System.Globalization.CultureInfo, Boolean)
   bei System.Resources.ResourceManager.GetStream(System.String, System.Globalization.CultureInfo)
# 5 #
Anwendung: WpfApp.exe
Frameworkversion: v4.0.30319
Beschreibung: Der Prozess wurde aufgrund einer unbehandelten Ausnahme beendet.
Ausnahmeinformationen: System.Runtime.InteropServices.SEHException
Stapel:
   bei System.Reflection.RuntimeParameterInfo.get_Name()
   bei System.Diagnostics.StackTrace.ToString(TraceFormat)
   bei System.Environment.GetStackTrace(System.Exception, Boolean)
   bei System.Exception.GetStackTrace(Boolean)
   bei System.Exception.ToString(Boolean, Boolean)
   bei System.Exception.ToString(Boolean, Boolean)
   bei System.Exception.ToString(Boolean, Boolean)
   bei System.Exception.ToString()
# 6 #
Name der fehlerhaften Anwendung: XYZ.exe, Version: 2015.0.496.5054, Zeitstempel: 0x54ea834f
Name des fehlerhaften Moduls: KERNELBASE.dll, Version: 6.3.9600.17278, Zeitstempel: 0x53eeb460
Ausnahmecode: 0xe0434352
Fehleroffset: 0x00012f71
ID des fehlerhaften Prozesses: 0xa68
Startzeit der fehlerhaften Anwendung: 0x01d0559cb7ec4ed6
Pfad der fehlerhaften Anwendung: \\share\XYZ.exe
Pfad des fehlerhaften Moduls: C:\WINDOWS\SYSTEM32\KERNELBASE.dll
Berichtskennung: 010514d0-c190-11e4-bf04-78542e186754
Vollständiger Name des fehlerhaften Pakets:
Anwendungs-ID, die relativ zum fehlerhaften Paket ist:
# 7 #
Name der fehlerhaften Anwendung: XYZ.exe, Version: 2015.0.496.5054, Zeitstempel: 0x54ea7a6e
Name des fehlerhaften Moduls: ntdll.dll, Version: 6.3.9600.17630, Zeitstempel: 0x54b0d74f
Ausnahmecode: 0xc0000006
Fehleroffset: 0x0006db27
ID des fehlerhaften Prozesses: 0x18dc
Startzeit der fehlerhaften Anwendung: 0x01d0559cb08529c3
Pfad der fehlerhaften Anwendung: \\share\xyz.exe
Pfad des fehlerhaften Moduls: C:\WINDOWS\SYSTEM32\ntdll.dll
Berichtskennung: ef389186-c18f-11e4-bf04-78542e186754
Vollständiger Name des fehlerhaften Pakets:
Anwendungs-ID, die relativ zum fehlerhaften Paket ist:

Hi,
>>The applications run fine when launching from a FQDN share
It sounds like a DNS suffix issue. When this issue occurs, please try to ping share on the client, then check if the corresponding IP address is correct. If the IP address is wrong, please adjust your settings of DNS to make sure that the client can resolve
the share correctly.
If it's very hard to change the settings of the DNS for some reason, as a work around, we can add the entry into the clients' hosts file.
Best Regards.
Steven Lee Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Connecting to Windows machines by name doesn't work

OK. Here's the story. PC/Linux guy for a long time. I'm the default sysadmin at work and for family. My wife bought me a Mac for my birthday, and I LOVE IT !!
The only problem is I still have 4 windows machines in the house, and I need to connect to them to get work done. (I actually now prefer using the Mac keyboard and mouse over the standard PC ones.)
I've gone through all the tips on joining my Mac to a Windows workgroup, and in the Finder, under the Shared section, I see the names for all my windows machines on the network. I can change my Connect as.. information, and see my windows shares.
Here's the problem, though. I want to use either VNC or MS Remote Desktop Connection on my mac to get my Windows Desktop. I cannot enter in just the name in either of these dialogs. It doesn't fined the machine by name only. If I figure out the explicit IP address, then it works fine.
Also, if I open up a terminal window, and attempt to ping a windows machine by name, it won't find it. What's going on here?
Thanks for all responses !!

G'day jimmy,
The wonders of name resolution are often a pain in the proverbial.
What response do you get from the "ping" when you attempt to use the name? Are you using the name of the PC on its own or "PCname.local"?
Cheers,
Rodney

Re-installing windows 7 on L440 - Error windows cannot find .bat

Hi,
I am trying to re-install windows 7 enterprise on brand new thinkpad L440 with an image from my company's SCCM server. I loaded the package on a USB stick. It was able to install T440P with no issue but I get the error ( windows cannot find bat make sure you typed the name correctly)
What is the cause of this problem. I need to rebuilt these machines ASAP but I am stuck with this error.

Hi,
I am trying to re-install windows 7 enterprise on brand new thinkpad L440 with an image from my company's SCCM server. I loaded the package on a USB stick. It was able to install T440P with no issue but I get the error ( windows cannot find bat make sure you typed the name correctly)
What is the cause of this problem. I need to rebuilt these machines ASAP but I am stuck with this error.

Preview Template - windows cannot find file

Hi
While previewing the template from MS Word, it pops up with the following error --
Windows cannot find
D:\..\tmp\271234562718103out.pdf718103out.pdf
When i try to preview it as a PDF, the pdf is located in the temp folder by the name 271234562718103out.pdf but somehow windows is trying to find out 271234562718103out.pdf718103out.pdf and pops up with the error.
How is this file name getting generated? Everytime it appends some of the last characters to the file name.
Any help would be greatly appreciated.
Thanks in Advance
CJ
Edited by: user10511095 on Apr 20, 2009 11:41 PM
Edited by: user10511095 on Apr 20, 2009 11:42 PM
Edited by: user10511095 on Apr 20, 2009 11:42 PM

Open the following registry and set the work directory which does not include any spaces:
HKEY_CURRENT_USER\Software\Oracle\XML Publisher\Template Builder for Word\TB_WORK_DIR
In my case the above Registry Key has the value:
C:\Documents and Settings\p.jain\Local Settings\Application Data\Oracle\BIPublisher\TemplateBuilderforWord
and I changed it to:
C:\DOCUME~1\PAAAB~1.JAI\LOCALS~1\APPLIC~1\ORACLE\BIPUBL~1\TEMPLA~1
and it worked.
I suggest you copy the path from the error which you receive.

My win 7 home premium cannot connect the sharing printer (EPSON L1100) in Windows server 2003 it say "Windows cannot connect to the printer. Accses denied"

in My office there is a win server 2003 R2 computer, i install a printer Epson L1100 in that computer, and it successfull, and i can print using that printer from that computer..
I already share this printer, but when i try to connect the printer from my laptop using OS Win 7 Home Premium.. it has error
"Windows cannot connect to the printer. Accses denied"...
and then i try connect using other computer but same OS (win 7 Home premium) it still has same error...
i usually connect to the server computer using //(the ip of computer) , for example
//52.30.20.66 .. that is my IP server..
and than i right click in shared printer which appears in windows explorer, and i choose
Connect... but it contain error "Windows cannot connect to the printer. Accses denied"..
anyone know the solution from this error???
i`m sorry if my english is bad.. i`m from indonesia

Got a local password/username on your Win7 ? Create the same on the 2003R2 as you seem in workgroup
net user /add useraccountname mypassword
net localgroup users useraccountname /add (I think it's users the name, you can validate to be sure) or
net localgroup administrators useraccountname /add in worst case.
nb, or add the user guess in the printer share security
Regards, Philippe

Getting Error Windows cannot find Adobe Air installer

Trying to install Adobe Air. Installation file wont run. Get error when i run the file.
"Windows cannot find 'C:\Users\Matt\AppData\Local\Temp\AIR4654.tmp\Adobe AIR Installer.exe'. Make sure you typed the name correctly, and then try again"
I am trying to run the current version of Adobe Air from the Adobe website. Please help.
Thanks,
Matt

Still no luck cant play LoL...Was having an issue with a asus start up file what was in the TEMP folder also said not found....deleted a registry for it and that one stopped coming up when the computer started...but i still cant install adobe air.

"windows cannot access specified device, path or file", adobe reader x

hi,
i had an older version of reader (9.something i think) that started making troubles, so i removed it (via control panel) and tried to use reader x instead. but after installing it i tried to run it and got this message titled "c:\programfiles\adobe\reader10.0\eula.exe":
"windows cannot access specified device, path or file. you may not have the appropriate permitions to access the item".
after clicking "ok" the program shuts.
i downloaded this version from adobe's site and registered. i also tried to go back to version 9 but the installation itself wouldn't go.
i'm using windows xp and downloaded reader using chrome. i deleted all previous adobe reader files from my computer prior to downloading, so it should behave as if this the first time this program was installed on it.
how can i solve it? (i've already tried going through the whole process again and again)
thank you for any help.

I have found out how to solve this issue..
Took A few days to figure it out and a lot of installs and un-installing
Install CS6 master collection again and restart your machine- Make sure all anti-virus is disabled
What you have to do:
1. Press Start
2. go under "Abode Master Collection CS6 (it should say its empty)
3. now left click the folder "Adobe Master Collection" and open it..
4. it will now come up with all programmes that SHOULD have worked - their thumbnails will not be visible it will look as if its corrupted.
5. Now this is a long procedure- go on the first shortcut, lefts click and go to properties.
6. Then select the option that says "Open File Location" it will then take you to its main folder.
7. Left click the highlighted Programme within the main folder, then go on properties
8. Go on the security Tab, press "continue" then you go on "Add" then type your account name, then "check name" then tick the box "full control"
9. Then navigate to the "compatibility" Tab and select "Run this programme as an administrator (if you don't do this it will come up with another error)
You should now have the thumbnail (picture) for the programme now
You have to now repeat this for the rest of the programmes/shortcut's within the "Adobe Master Collection" Folder

Windows cannot find AcroTray.exe

Hi,
I'm using adobe acrobat pro 9 and started getting an error message everytime I attempt to create a pdf file using ms office whether it be in word, excel, or even in ms project
The error message is:
Windows cannot find 'C:\Program Files (x86)\Adobe\Adobe Acrobat10.0\Acrobat\AcroTray.exe'
Make sure you typed the name correctly, and try again.
This just started to happen last week after using acrobat pro for the last two years with no problems.
I am using windows 7 home edition.
Any suggestions on how to fix this would be greatly appreciated as I've had no success
Garry

I would run Help>Repair. Then do the updates to AA9 also. That may repair the problem. As suggested, it looks like the AA X trial was installed and then removed. One of the problems of removing a version of Acrobat is that it often breaks the remaining versions. Hopefully, a repair will do the job.
However, you should be able to find AcroTray in the AA 9 folder also. Check the startup folder to be sure that is the version that is being called. AcroTray should be running in the background to enable PDF creation.

Windows cannot access the specified device, path, or file. You may not have the appropriate permissions to access the item.

Hi, i'm a Windows 7 user of HP Pavilion dm4.
It has been weeks since iTunes works properly on my computer. I'm here to seek help from professionals or people who had encountered it before. Whenever I double-click on iTunes, it prompt me a message "Windows cannot access the specified device, path, or file. You may not have the appropriate permissions to access the item." But another thing is, i'm the only adminstrator on this laptop. If I don't have permission, who has? Sigh.
I had tried uninstalling and installing iTunes from official website many times but to no avail.

Hi,
Also, please make sure your current user is a administrator account and have permission to open the file.
Right-click the file or folder, and then click Properties.
Click the Security tab.
Under Group or User names, click your name to see the permissions you have.
Have you installed 3rd software in you computer? please turn off them temporarily to check if this issue still occurs.
Here is an article you can refer to.
http://support.microsoft.com/kb/2669244
Andy Altmann
TechNet Community Support

X200: Windows cannot find file error (& cygwin problem)

Often (about half the time) when I double click an icon (.docx files typically) to open I get a error reading"Windows cannot find ‘C\Users\username\Desktop\filename.docx’. Make sure you typed the name correctly, and then try again." I can *always* resolve this by simply double clicking again. I ran a complete disk check (the thing that runs on reboot) and it passed with no errors. OS: Vista with all updates, Apps: Office 2007 with all updates. Disk: Solid state (128GB) SAMSUNG MMCQE28G8MUP-0VA
Any suggestions for troubleshooting tips?
I also wonder if this might be related to the following problem. I have CYGWIN installed, and once I have changed a file in emacs and saved it, emacs can no longer find it (no matter what I do). These days I get the message within emacs "file is not readable", although in the past the error has said something about a fork.
Message Edited by andy402 on 04-25-2009 07:27 PM

There is a primitive called 'Request Deallocation' that is suppose to free up resources in a VI after it is called. You could try using this.
Paul <--Always Learning!!!
sense and simplicity.
Browse my sample VIs?

Windows cannot conects .. name

Similar Messages

Maybe you are looking for