Windows dont loading after recovery is finished - SP M30

Hi,
I am trying to repair a Satellite Pro (M30).
I've run the recovery disk, but after the reboot
Windows fails to load. The cursor appears briefly,
but I am left with a blank screen. There is no
harddisk activity.
Any ideas?
thanks,
Brian

Hi
Well, does this problem occurs after the completely recovery procedure?
In my opinion this issue occurs because the HDD will be not recognized.
Please enter the BIOS and check the boot frequent and if the primary IDE settings are set to HDD.

Similar Messages

T40 missing or corrupted \windows\system file after recovery process

My T40 Thinkpad had a corrupt drive so I secured the recovery disks from IBM to rebuild the hard disk. The recovery process seemed to work well, but when completed and prompted to remove all disks and reboot, the system booted and failed before Windows XP loaded with an error message that the windows\system file was corrupt or missing. Any recommendations on how to succesfully recover? Thanks.

boot off the WinXP Disc and run a repair. Did it mention the boot.ini file being corrupt, or something else?
T61 15.4" T9300 (2.5GHz 6MB L2) Windows 7 Professional x64 4GB Memory, NVidia Quadro NVS 140M

Why is it no longer possible to make the download window close automatically after downloading is finished ?

Only two days ago the download window closed after downloading.
What happened ?
And why is there a new and less efficient download window ?

Firefox now manages the downloads in the Downloads folder in the Library (History > Show All History > Downloads) and download are treated as history items.
*https://support.mozilla.org/kb/Downloads+window
So you open the Library if you inspect all downloads and this Library window doesn't close automatically.
When a download is in progress then you see a download progress (timer) bar on the Navigation Toolbar instead of the Download Manager button and that button is highlighted once the download has finished to make you aware the their are new downloads.
You can view the new Download Manager in a tab by opening the about:downloads page and consider to open this page in a separate window.
You can set the Boolean pref browser.download.useToolkitUI to true on the about:config page to restore the classic Download Manager window and make all download settings appear in "Tools > Options > General".
*http://kb.mozillazine.org/about:config

Nvidia Settings not saved or dont load after reboot

Hi there , look well i try to put the follow settings :
Well during my current session that apply without problems , well when i reboot , or shutdown after i power on the pc . the settings are reset to :
How i can saved and load the settings when i start my session again , because i try to put in my ~/.xinitrc
the follow lines :
nvidia-settings --load-config-only (this dont work for i want load the settings when i start my session)
nvidia-settings -a InitialPixmapPlacement=2 (For Firefox , i dont know if this works or not)
well , you have another ideas , to solve this ???
thank you for any answer you can give me.
-- mod edit: read the Forum Etiquette and only post thumbnails http://wiki.archlinux.org/index.php/For … s_and_Code [jwr] --
-- Tell me mod , how i can put the Thumbnail , when the source site , dont give the code from the site to put thumbnails , this forum support make the thumbnail??? ---
Last edited by inukaze (2014-06-12 15:08:39)

What DE are you using? (if any) I have a similar problem since the last Gnome 3.12, doesn't matter where I put the command "nvidia-settings --load-config-only" it just doesn't work. I have to either open the GUI or issue the command on the terminal for it to happen, I tried with ~/.config/autostart/ /etc/xdg/autostart/ with a .xprofile file, a .xinitrc, nothing works, I can't tell from where this problem originates. Other programs start just fine with the mentioned methods, then it must be something wrong with the way nvidia is invoked I guessing, a couple of months ago was working flawlessly.
Last edited by RJQ (2014-06-20 21:29:31)

Dv6-2170eo windows update fails after recovery

I have a HP dv6-2170eo netbook with Windows 7 Home premium (64-bit). My origin hard drive (640GB) failed and I replaced it with 1TB hard drive. I used the recovery DVD's that I made when I bought the laptop and then reloaded Windows 7 on the new hard drive.
After reloading , Windows Update does not work.
This is the error I get:
Windows Update cannot currently check for updates, because the service is not running. You may need to restart your computer.
I can't even install Windows Defender or Microsoft Security Essential
Intel Chipset driver from 2009-06-04
My internet access is OK.
I have restarted my netbook and the error is the same.
I have reloaded Windows 7 and the error is the same
Please help me
Haggann

I had the same problem with an HP G72. If you have an Intel Chipset, goto Intels website and download there "Intel Rapid Storage Technology Driver" and install it. I had the exact same problems and this fixed them. For some unknown reason this driver is not available on HP's website. I just Googled the driver and it took me straight to Intels website where I downloaded it. Get the driver that you can run from within windows and not the one that runs from a floppy.
Good Luck,

T42P-Rebooting Windows after Loading/installing Recovery Discs

I just installed a new hard drive after crash, and loaded new purchased recovery disc set from Lenovo. Any ideas how to get machine to boot to windows after installing? Keeps rebooting to Recovery menu with no options for windows. Assume this recovery disc set brings laptop to 'as new shipped' condition.
thanks,
B

As the recovery discs are read, the recovery program copies a number of compressed files over to the hard drive. It then boots back into the recovery program, "prepares" the hard drive (this process takes some time and the dialog box appears to hang with no evident hard drive activity) and then extracts the system and application files to their proper locations. After this it boots into Windows to begin the configuration process (unless you press F11 at the prompt, which puts you back into the recovery program and allows you to do a custom recovery without going through the configuration process for the full recovery). It will boot into Windows a number of times as it completes the configuration process.
I hope I remembered all that correctly. Anyway, at which point is your machine rebooting?
Don
Message Edited by ConnectDon on 07-11-2008 07:32 PM

Windows 7 won't load after installing new Hard Drive and Recovery software

HP G72 Notebook PC
xz218UAR
I guess a virus crashed my hard drive so I bought a new one. I installed the new drive and loaded the recovery disks that I also bought from HP. Apparently Windows didn't load properly and it keeps telling me to RELOAD WINDOWS. I've tried starting over from Disk 1 but it's not doing anything different to fix it.
I removed the new hard drive and reinstalled it but it's still doing the same thing.
What am I doing wrong and HOW DO I FIX IT?

Hi,
Before trying the following, make sure you can still read the 25 Character Product Activation key on your Windows COA label ( 5 blocks of 5 alpha/numeric sets ).
Assuming that this is just a problem with the Recovery process, there is a straight forward work around if you have ( or can borrow ) a retail Windows 7 installation disc that is exactly the same version as your OEM installation - ie if your notebook came with Windows 7 Home Premium 64bit this is the exact retail version you would need.
If you don't have access to a retail disc, you can create an installation disc yourself using another PC - just download the correct Disc Image from the link below and use an application such as ImgBurn to burn the ISO correctly to a blank DVD - a guide on using ImgBurn to write an ISO to a disc is Here. These Images are clean and from a well-respected source, however there are only limited versions available.
Windows-7 sp1-iso-official-32-bit-and-64-bit
Use the disc to perform the installation, enter the Windows activation key found on the COA Label when requested and when the installation has completed, use the 'Phone Method' detailed in the link below to activate the OS - this method supported by Microsoft and is popular with people who just want a clean installation of Windows 7 without the additional software load normally bundled with OEM installations.
http://www.kodyaz.com/articles/how-to-activate-windows-7-by-phone.aspx
Any additional drivers you may need can be found Here.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

Windows 7 - Dont boot after install (Hyper-V)

Hi,
Today I was install a VM with Windows 7 Ultimate. The setup ran very fine, I've allocated 200GB in virtual HD and set 2GB to RAM.
After the install completes, a black screen appear and Windows dont boot (or start)...
Any tip?

Just ran into this same issue.
My problem got resolved after using the x64 version DVD of Win7 (just x64 instead of the DVD that had both x86 and x64 versions).
What I did:
My host is Windows 8.1
After installing Windows 7 x64 as VM on my 8.1 based laptop two days ago, I wanted to do the same on my desktop PC, but I had the same issue described here.
I used a DVD just with the x64 version for my laptop and a DVD with both x86 and x64 version for my desktop.
Tried repairing as advised by a post, but got the error: "This version of System Recovery Options is not compatible
with the version of Windows you are trying to repair. Try using a recovery disc that is compatible with this version of windows."
I exported and imported the VM from my laptop to my desktop to test it and it ran with no problems.
So I tried the DVD that had just the x64 version of Win7 and that installed without issues.
I'm curious if this happens only when a DVD with more than one Win7 versions is used.

HT1386 I just reinstalled my windows operating system and decided to put on windows 8. After loading all of my music back into a freshly installed itunes, my 4th gen ipod is not recognized by itunes. My 1st gen ipod nano works with no problem. Help!

reinstalled my windows operating system and decided to put on windows 8. After loading all of my music back into a freshly installed itunes, my 4th gen ipod is not recognized by itunes. My 1st gen ipod nano works with no problem. I can eliminate any problems with the cable and connection.
I've stopped and started the service, and also have performed cold reboots.
Nothing seems to have helped the situation.
Help!

See:
iOS: Device not recognized in iTunes for Windows
I would start with
Removing and reinstalling iTunes, QuickTime, and other software components for Windows Vista or Windows 7
iTunes for Windows: Device Sync Tests
Have you tried on another computer to help determine if you have a computer or iPod problem?
The iPod Classic uses different drivers than the Nano

Using Firefox 4 & Windows 7. Everytime I start Firefox from a shortcut to a website it comes up with the following error 'there was a problem sending the command to the program'. The requested website does load after this. with no problems.

Using Firefox 4 & Windows 7. Everytime I start Firefox from a shortcut to a website it comes up with the following error 'there was a problem sending the command to the program'. The requested website does load after this. with no problems.
If a shortcut is used while Firefox is already open the error does not occur.

As reported in earlier replies, the annoyance disappeared after I upgraded to Roboform 7.5.6, from 7.5.4.
Regards, Steve

HT1766 please help...we updated ipod2 4.1 to IOS 5.1 at itunes...after it was finished only the contacts were restored...not the music & videos...we found the backed up data in the pc(windows 7)after entering %appdata%..pls help how to restore..thanks!God

please help...we updated ipod2 4.1 to IOS 5.1 at itunes...after it was finished only the contacts were restored...not the music & videos...iwe found the backed up data in the pc(windows 7)after entering %appdata%..pls help on how to restore...we will appreciate it very much....thanks! God bless!

The iPod backup that iTunes makes does not include synced media like app, music and videos. Thus, you wll have to resync those back to your iPod.
If necessary you can redownload iTunes purchases by:
Downloading past purchases from the App Store, iBookstore, and iTunes Store

The webpage does not load after pressing enter or CTRL+ENTER. My OS is Windows 7 Ultimate

I have tried installing the older version Firefox 3.6. After entering the URL on address bar it does not load after pressing enter or CTRL+ENTER

This issue can be caused by an extension (AVG Safe Search can cause this) that isn't working properly.
Start Firefox in [[Safe Mode]] to check if one of the extensions is causing the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > Appearance/Themes).
* Don't make any changes on the Safe mode start window.
* https://support.mozilla.com/kb/Safe+Mode
* [[Troubleshooting extensions and themes]]
In Firefox 4 you can use one of these to start in [[Safe mode]]:
* Help > Restart with Add-ons Disabled
* Hold down the Shift key while double clicking the Firefox desktop shortcut (Windows)

I want all new windows to open in tabs but they dont, even after I have selected the option " Open new windows in new tab instead"

Al the details are in the question: I want all new windows to open in tabs but they dont, even after I have selected the option " Open new windows in new tab instead"

Start Firefox in [[Safe Mode]] to check if one of the add-ons is causing the problem (switch to the DEFAULT theme: Tools > Add-ons > Appearance/Themes).
* Don't make any changes on the Safe mode start window.
See:
* [[Troubleshooting extensions and themes]]

Windows does not start after recovery

Hi, my son's sattelite 1800 started getting slower and slower to the point where it took almost an hour to boot into Windows. It got to the stage where it looked like recovery from the CD's was the only route - so we did. All looked successful from the recovery point of view but Windows XP Setup displays 'Please wait...' with normal looking disk activity for 20-30 seconds and then hangs - no disk activity, mouse stops responding. I've gone through the recovery in 'expert' mode and don't see any issues with the recovery process. Questions:
1. Has anyone else seen this?
2. What else can I do diagnostic-wise?
3. What, fundamentally, does the recovery process do/ (does it re-format partitions, might it have left a virus?)
4. Am I best following h/w or s/w diags?
Bitshifter

Hello
On this way it is not easy to give you a proper explanation why this happen. If you use the recovery CD for OS installation the HDD will be formatted and the OS will be clean installed. IF you use standard mode the whole HDD capacity will be used for just one partition. Using expert mode you can create two partitions or you can install OS on persisting partition.
Usually after recovery reinstallation there should not be any problem except for HDD malfunction.
Please wait message occur after first start and you can not compare it with usual boot up process. That first start after recovery procedure takes much longer time because the OS must detects all hardware components, install drivers and prepare the OS for the usage.
For further start the OS doesnt need so much time for boot up process.
Bye

Windows 8 start up after recovery media disk problem?

My laptop has the Recovery blue screen with error code 0xc0000001 so I use the System Recovery DVD Media for Windows 8. After the process, it log onto Admin then the message "Windows could not complete the installation. To install Windows on this computer, restart the installation." I restart it several times, but that message keep popping up. What should I do?

Hello "ItsThatHim,
Take a look at this document, and let me know if the troubleshooting steps help resolve your issue.
Good luck!
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

Windows dont loading after recovery is finished - SP M30

Similar Messages

Maybe you are looking for