Windows iso to a partition of a hard drive

Hi guys.
I have the iso of Windows 7 and i would lik eto burn it into a partition of an external hard drive. I tried with disk utility, but it will give me an error as the partition is in fat32, so i tried the bootcamp assistnat feature. The problem of that is that it wont recognize the single partition, only the whole drive.
Is there any other way I can burn that iso ?

Hi 
Welcome to the Forum please try these steps given below this might help you to fix your issue.
Disclaimer
You are using this guide at your own risk. I don't take any responsibility for any problems.
Important information
Please create a set of recovery discs, Windows Vista or Linux System Repair Disc and back up all important data before you will do anything.These steps will save you a lot of troubles if something will go wrong.
Table of Contents:
A How to use the guide
B Basic information which you need to know
C Our problem
D Possible solutions to the problem
E Pros and cons
F Convert the C partition
G Remove the HP_TOOLS partition
H Remove the RECOVERY partition
 I  Remove the SYSTEM partition
J  FAQ
Let us know how it goes!
"I work for HP."
****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
****Please mark Accept As Solution if it solves your problem****
Regards
Manjunath

Similar Messages

  • I guess I didn't explaine that I have a healthy operating Windows 8 Boot camp partition on my hard drive. When I upgraded to Mavericks I am no long able to access the bootcamp partition from the disk icon in system preferences; the Windows 8 works fine.

    On both Mini Mac and iMac 27" I am no longer able to utalize the Startup Disk icon in System Preferences; the Windows 8 on Bootcamp partition works fine if I close the Mavericks OX and select the Windows partition at bootup from the hard drive. My question is why don't the icon in System Prederences work anymore since I upgraded to Mavericks. Also, Users & Groups, Printers & Scanners icons no longer work either.

    On both Mini Mac and iMac 27" I am no longer able to utalize the Startup Disk icon in System Preferences; the Windows 8 on Bootcamp partition works fine if I close the Mavericks OX and select the Windows partition at bootup from the hard drive. My question is why don't the icon in System Prederences work anymore since I upgraded to Mavericks. Also, Users & Groups, Printers & Scanners icons no longer work either.

  • Can I partition an external hard drive to run windows games on my Macbook Pro

    I want to play windows games on steam but I am not sure if I want to partition my Macbooks hard drive. I heard you could partition external hard drives but didn't know if you could run games on that external hard drive. I have a lot of files on my computer and don't want to take time to move my files to the external hard drive, so can I buy the external hard drive and then partition it to run window games or do I have to partition my actual default hard drive?

    Hi! If your macbook doesn't have a cd drive you need to have Windows 7 but an ISO image, you can't just copy the contents of the copy into a USB and expect it to work. There are many tutorials on internet on how to obtain an ISO image from an installation disc, for example: http://pcsupport.about.com/od/software-tools/a/create-iso-image-file.htm As for "just download Windows 7" (i suppose you mean free download) this is not the right place to ask, believe me. Try searching Windows 7 ISO on google, but be careful with what you download and form where, also you are going to download the Windows drivers from the Bootcamp program, try reading this manual to give yourself a better idea: http://manuals.info.apple.com/MANUALS/1000/MA1636/en_US/boot_camp_install-setup_ 10.8.pdf

  • Is it possible to use Boot Camp to partition an external hard drive so there is a OSX partition and a Windows partiton?  I want to use the external drive for backup only, NOT to load Windows and NOT to use as a boot drive.

    I have partitioned the internal hard drive and am running Lion and Win7 Pro on my iMac i5 2.7GHz with 16GB RAM.  Can I use Boot Camp to create a Windows partition on an OSX external hard drive to use for backing up both systems to the same HDD?  I do NOT want to install OSX Lion or Windows 7 Professional on the external drive.  I do NOT want to boot either system from the external drive.  The 3TB external drive is for backup only.

    Use NTFS for Windows and buy Paragon NTFS for OS X
    You can also try Paragon HFS for Windows
    As long as you are using for data and backups, you can leave the drive as GPT too.
    I would recommend strongly to always have a 2nd bootable Mac OS drive, only need 30GB partition. System maintenance. Though LIon Recovery Mode finally makes it less but not totally unneeded.
    And yes you can use Windows to create a partition.
    Boot Camp is too broad. Do you want or mean BC Assistant? not needed but probably possible.
    MBR has trouble with 3TB drives.

  • How can I partition my external hard drive supporting mac OS in one partition and windows OS in another?

    Hello everyone, how can I partition my external hard drive supporting mac OS in one partition and windows OS in another?

    OK. Start with:
    1. Open Disk Utility in your Utilities folder.
    2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
    3. Under the Volume Scheme heading set the number of partitions from the drop down menu to two (2). Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the process has completed.
    4. Click on the Erase tab in DU's main window. Select one of the two partitions, preferably the first one, change the Format type: to MSDOS then click on the Erase button.

  • HT201250 What does it mean to "partition" an external hard drive? Is it something that I want to do?

    What does it mean to "partition" the external hard drive?  Is it something I want to do?  How do I save files from another hard drive to the new one?  I have to reformat the old one as it was not set up correctly.  The drive I have is Seagate but not specifically for MAC, so I have to format it.. never have done this before. Don't know the jargon.  I read that Time Machine will back up automatically but I want to take files from the old drive to the new one.  Do I have to take them to the computer first and then to the new drive?  I need more memory on my computer. It's way too cluttered and congested.  HELP!

    Whoa! Slow donw. TRhere's a lot here. I would suggest you buy a good book on computers in general or macs in particular, one is "OSX the missing manual".
    What does it mean to "partition" the external hard drive?
    It means you take one large drive and make it into more than one volume. This means that it might show up as 2,3 or 4 inde[pendenmt drives. Each one could have, for example, a different operating system on it. Its  a good thing to do if you want to use a drive for several purposes
    Is it something I want to do?
    beats me, you didnt way what you're trying to accomplish. Sorta like sking "should i turn left?"  Depends on where you want to go.
    How do I save files from another hard drive to the new one?
    See advice n book above. Copy them in finder. Copy them in unix. Use a backup or sync utility. No different from Windows in that respect.
    I have to reformat the old one as it was not set up correctly.  The drive I have is Seagate but not specifically for MAC, so I have to format it.. never have done this before. Don't know the jargon.
    Hook it up. Run disk utility. Partition 1 or more partions. GUID map.  Format each partition Mac OS extended, Journaled.  for more, read book, above.  Seriously - we could give you more tips, but you really should learn enough to be comnfident.
    I read that Time Machine will back up automatically but I want to take files from the old drive to the new one.  Do I have to take them to the computer first and then to the new drive?
    I have no idea what you are asking.
    I need more memory on my computer. It's way too cluttered and congested.  HELP!
    What kind of memory and why?  RTAM? Hard drive space? Explain. By the time you are done explaining, i suspect you will have ansered your own question.
    Good luck,
    Have you read the PDF manual for your cmputer?
    Have you used a search engine to look for info, for example, in two seconds i got this from google and wikipedia:
    http://en.wikipedia.org/wiki/Disk_partitioning
    Grant

  • Installing windows xp pro on a separate internal hard drive in ntfs

    Does anyone here know how to install windows xp professional on a separate internal hard drive in NTFS with bootcamp. In the bootcamp manual it says I can ,but when I reach the list of partitions in xp setup, C: Partition3<BOOTCAMP> {FAT32} Is not on the list. I called support and they told me Apple doesnt support BOOTCAMP on a separate drive and to check the forum though the manual says It can be done.

    Rather easy enough to do. People install XP and Vista all the time on 2, 3rd or 4th drive in Mac Pro. I know Vista 64-bit on Mac Pro has best support for addressing RAM and drivers.
    http://discussions.apple.com/thread.jspa?threadID=1511099
    http://discussions.apple.com/thread.jspa?threadID=1510044
    http://forums.macrumors.com/forumdisplay.php?f=86

  • Partitioning an external hard drive for Mac and PC

    I want to partition an external hard drive (3TB) into 3 even partitions. I want to use one for PC storage, one for Mac storage and the last for Mac backup. Is this possible and how do I do it?

    Drive Partition and Format
    1. Open Disk Utility in your Utilities folder.
    2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
    3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Apply button and wait until the process has completed.
    4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
    5. Set the format type to Mac OS Extended (Journaled.) Click on the Security button, check the button for Zero Data and click on OK to return to the Erase window.
    6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
    7. Re-partition the drive to create the three partitions. The one you wish to use on a PC you should format MSDOS (FAT).
    When you connect the drive to your PC it should have no problem reading the partition set up for a PC. Now while on the PC you may wish to consider reformatting that partition using ExFAT (if supported on your PC.) This format is more compatible with both OS X and NTSF supporting long file names and other FAT filesystem irregularities.

  • How to put a recovery partition on the hard drive

    How can I create a recovery partition on the hard drive of my laptop. I had to reinstall the whole system, and tried to use the HP recovery software they sent me but it quit when it was about three quarters the way finished. I had to use a copy of windows 8 to put the system back on my laptop. After I got it all straighten out, I updated it to windows 8.1 and it seems like the computer runs a lot faster with windows 8.1 on it. Now I need to find away to install a recovery partition on my hard drive.
    Thank You
    Garry Crist

    When requesting assistance, please provide the complete model name and/or product number of the HP computer in question. HP/Compaq makes thousands of models of computers. Without this information it may be difficult or impossible to assist you in resolving your issue.
    The above requested information can be found on the bottom of the computer or inside the battery compartment. Please do not include the serial number. Please enter the model/product information into HP's Online Consumer Support page and/or post it here for our review.
    A Recover partition is something the factory places on the computer. It is an image of the factory installation and the software required to restore the computer to a factory like state using that image. You will not be able to create a Recovery partition on your computer unless you use the HP Recovery Discs to return the computer to a factory like state. Please note the HP Recovery Discs and the resulting HP Recovery partition will only contain an image of Windows 8 that cannot be updated to reflect the installation of Window 8.1.
    My suggestion is to use the Windows "System Image Backup" utility to create an exact image of the Windows 8.1 partition as it currently is. If your computer developes an issue or you need to replace the hard drive, all you have to do is "restore" the image to the computer. You will need to use an external USB hard drive or other media to store the image. Please see Windows 8.1 Tip: Use System Image Backup for instructions on creating and storing a "Windows - System Image Backup."
    If you have any further questions, please don't hesitate to ask.
    Please click the white KUDOS star to show your appreciation
    Frank
    {------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
    Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
    This is a user supported forum. I am a volunteer and I don't work for HP.
    HP 15t-j100 (on loan from HP)
    HP 13 Split x2 (on loan from HP)
    HP Slate8 Pro (on loan from HP)
    HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
    HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
    HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
    HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
    HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

  • I just purchased the Mac Mini Server with the intention of replacing Lion Server with Lion for the first hard drive while installing Windows 7 thru Bootcamp on the second hard drive. Is it possible for me to do this? Thanks.

    I just purchased the Mac Mini Server with the intention of replacing Lion Server with Lion for the first hard drive while installing Windows 7 thru Bootcamp on the second hard drive. Is it possible for me to do this? Thanks.

    I would use Parallels or VMWare and use the second drive to hold the virtual machine. That way the VM only uses the space that it needs and you can still use the remainder of the drive for other things, not to mention that you would not need to reboot to run windows.
    Also Time Machine does not back up a boot camp partition.

  • Partition of External Hard Drive

    I am trying to partition an external hard drive into three partitions - one for the time machine backups, one for miscellaneous storage and one for storage of files that I can share with a PC. I was able to partition the drive successfully but all three partitions are in the Mac OS Extended (journaled) format. I understand that I need to change the format of the part I want to share with the PC into FAT but when I click on that drive, I don't have the option. I tried looking under the "erase" tab but the only options are: Mac OS Extended (journaled); Mac OS Extended; Mac OS Extended (case sensitive journaled) and Mac OS Extended (case sensitive). Now, if I look at the entire hard drive (not clicking on one of the partitions), the option is there. I could erase the entire thing using the MS DOS (FAT) option, but I don't want to do that. How can I format only one of the partitions in the MS DOS (FAT) format?

    I think it's because of the drive's Partition Map Scheme. In Disk Utility, select the drive in the left side bar. Look at the bottom of the window, and find Partition Map Scheme. If it is Apple Partition Map, you will not be able to format it as MS-DOS (FAT).
    The way to fix this is to go to the Partition tab. For Volume Scheme, select 3 Partitions (even if it already is 3 partitions). Click on the Options... button. In the window that opens, select either GUID Partition Table or Master Boot Record. GUID Partition Table would be best for use on the Mac, as long as the PC is OK with it (I'm not sure). Now, when you return to the Partition tab, you should be able to select MS-DOS (FAT) for one partition while keeping the others formatted for Mac.

  • Partitioning a single hard drive?

    Before anybody gives me a hard time about asking a repetitive question about partitioning let me explain. I know their are several threads on the forum that say this or that about partitioning but I would like to know some definite opinions. I've just got one Western digital 300gb hard drive on ide 1 (maybe I'll add another hard drive later) with windows XP loaded as the operating system.
         1.Do you guys think it is good idea to partition this hard drive?
         2. When would you partition?
         3. How would you seperate the partitions for example would you make a 10 gig partition for the hard drive, etc.
         4. What are the advantages of partitioning?
    Thanks for any feedback.

    :Don't worry! I will never hammer someone for asking a question .First of all, Yes I think you should PARTITION a HDD that is as BIG as yours!!. But keep in mind the BEST time to do it is BEFORE OS installation. That does not mean that it is BAD to do it after with a 3'RD party program ie. PARTITION MAGIC..ect... How big,and how many partitions is totally up to you,(as long as you are within space paramaters)..I myself would CUT that size drive into at least 2 150GB partitions.But it also depends on what you are going to put on it ...You can have 100GB for the WIFE, 100GB for PICS or DVDS, AND 50GB for the OS and the rest for GAMES!!! This is what you have to decide....Sean REILLY875

  • When trying to remove a partition on my hard drive I couldn't

    when trying to remove a partition on my hard drive I got an error and the option was grayed out in boot camp assistant. error message:  "The startup disk cannot be partitioned or restored to a single partition.  startup disk must be formatted as a single Mac OS Extended (Journaled) volume or already partitioned by Boot Camp Assistant for installing Window".

    I am going to revise my question to this.  If I compress my itunes folder which would save me a considerable amount of space will this make the music and apps information stored in there unsyncable? 

  • Create two partitions on one hard drive?

    Hi
    I have an external hard drive I want to use for both PC and Mac.
    Can somebody please help me on how to create two partitions on the hard drive, one with Mac extended format and one with NTFS format.
    Many thanks

    pbmarcano wrote:
    Alternatively (my usual approach): Format the Windows partition to FAT then when you bring it to a windows machine, format the partition to NTFS.
    No need to format to NTFS, you can convert to NTFS with no destruction of data.
    Just format to FAT in Disk Utility, then when accessing the FAT drive in WIndows:
    *To convert a volume to NTFS from the command prompt*
    http://technet.microsoft.com/en-us/library/bb456984.aspx
    Open Command Prompt. Click Start, point to All Programs, point to Accessories, and then click Command Prompt.
    *In the command prompt window, type: convert drive_letter: /fs:ntfs*
    For example, typing convert D: /fs:ntfs would format drive D: with the ntfs format. You can convert FAT or FAT32 volumes to NTFS with this command.

  • Windows xp inst disk can't find hard drive. got recovery disks and loads files and starts windows

    I have a compaq 110C-1100DX  I believe has a virus I can't find. If I try to reinstall windows XP it can't find the hard drive. I have downloaded the drivers from intel for the controller  ICH7M/MDH SATA AHCI controller ( could not find on hp's site ) and slip streamed onto the inst disk, still no good. ordered a restore disk  from HP ( both ways I am using an external cd/dvd drive )
    . It copies files like it is going to install and then just continues to boot windows. The hard drive shows up in the bios and my computer, but not in device manager or disk management. all I can see are removable storage. I have run the diagnostics in the bios and they passed. I have lost use of the keyboard in windows, but it works to F key @ boot and works when needed during the installation process.
    thanks for any help you can give me. I have installed, upgraded and reinstalled operaring systems many times and never been stymied like this.

    If the drive is listed in Disk Utility do the following:
    Extended Hard Drive Preparation
    1. Boot from your OS X Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger or Leopard.)
    2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
    3. Set the number of partitions from the drop down menu (use 1 partition unless you wish to make more.) Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the partition scheme to GUID (only required for Intel Macs) then click on the OK button. Click on the Partition button and wait until the process has completed.
    4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
    5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
    6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
    After formatting has completed quit DU and return to the installer. Complete the OS X installation.
    When you are installing Windows via Boot Camp the Windows installer needs to format the Boot Camp partition. Be extra careful to select only the partition you created with Boot Camp. The XP installer should label the partition "C:", and you should recognize it by its stated size.

Maybe you are looking for