Windows messenger & parallels need access to port 1503

windows messenger and parallels need access to port 1503 I have set my firewall settings to allow access to port 1503 but messenger still can not get access

Which firewall - OS X or Windows?
What networking model are you using - NAT; bridged; host only?
Do you have a hardware firewall that could be blocking it?

Similar Messages

How do I set up Airport Extreme Airport Disk as Central Media Storage when I have Directv, Windows and Mac needing access?

I have an always on PC in my living room, but I want the macbook pro to have the same media without taking up the space. iTunes Shared lacks the sorting features of having the library directly associated. What I want to do is setup a hard drive on my AEBS to house all my media.
I have a 120GB SSD on my PC in the LR. (with an 80GB drive I may put with it for extra space if needed)
A 250GB MBP
A 2TB drive (installed in a USB/eSATA enclosure)
A 1TB drive
A 500GB usb WD Passport
I use iTunes for Movies, Music, Podcasts
I use Picasa for Pictures
I want to house these large libraries on the AEBS Airport Disk and have the MBP and PC access the media. I ideally want iTunes to identify that as the iTunes Media Library for both the MBP and PC. I haven't found a good run down of how this would work. Especially since I want to make sure Directv can access the media as well as the PC and MBP.
I will store all my media on the 2TB, I will use the 1TB to backup all the media in a safe, and the 500GB I want to split for Time Machine and Windows backup. With all my media off those drives, 500GB should be enough space to keep backups for a while to restore programs and what not from.
Thanks for any help.

I want to house these large libraries on the AEBS Airport Disk and have the MBP and PC access the media. I ideally want iTunes to identify that as the iTunes Media Library for both the MBP and PC. I haven't found a good run down of how this would work.
Please check out the following TUAW article to see if it will help provide some additional details.
I will store all my media on the 2TB, I will use the 1TB to backup all the media in a safe, and the 500GB I want to split for Time Machine and Windows backup.
You may want to revisit your strategy to using an AirPort Disk for Time Machine backups and that is because Apple does not support this. If your backups are critical to you, then I would strongly recommend that you reconsider using another destination source option.

ISight stopped working with windows messenger (bootcamp/parallels)

A few days ago I installed windows xp pro via bootcamp. After installing the drivers and everything, windows messenger was great with the iSight and everything. Just today I installed parallels, and after opening windows i no longer have a "webcam" installed, and i noticed that even my "speaker" and "Microphone" settings have gone back to "Intel(r) Integrated Audio"
Any ideas how i could get this working again? The audio actually works, but I just need windows to find my iSight again...

Hi,
Parallels is not an application I have so I can not test this further.
I would think the answer may lie in the BootCamp forum where people may have tried the same thing as you or at any Parallels Forum you can find.
(Start here as there are links to the unintegrated ones).
7:32 PM Saturday; March 28, 2009

Need drivers for built in iSight for Windows XP Parallel Desktop

I'm trying to get my iSight built into my MacBook Pro to work in my virtual computer run on my Mac using Parallels Desktop 4 on and the virtual operating system is Windows XP. So the drivers need to be Windows compatible. I don't want to have to use a third party external camera when I have a built in one. The iSight will not work on Windows Messenger for Mac so I have to use my Windows operating system to make it work. I have not seen any downloadable drivers for the iSight on the Apple sight that would work for Windows. I would appreciate someone directing me to some if they exist.

Thank you so much for the help. I'm running Snow Leopard, so the specific references did not match exactly, but I was able to find my way. I had to finagle trying to get the drivers to load and be recognized by Windows XP, but it eventually did after a couple restarts and a few choice cuss words! Thanks again.

How do I set up original windows 8 DVD on a Macbook air when my external drive needs both usb ports?

got a brand new macbook air and want to set up an original Windows 8 DVD via bootcamp. Probleme: my external DVD needs 2 usb port connection so I want have a chance to plug in an usb drive at the same time.
Any other choice to get along?

ok I'll try this - why didn't I have this problem with my previous Macbook air - I cannot remember how I managed setting up an original Win 7 with exact.the same equipement. Has the bootcamp Software changed? I remember burning a cd with the Windows Driver.

Pse help. K7T66Pro2 cannot access serial ports in DOS window

My K7T266Pro2 won't access serial ports in a DOS window under Windows 98SE.
Windows programs can access the ports but no DOS programs - including my modem program, banking program, Tapcis Compuserve program and MDMDR a serial port diagnostic program.
I have tried both setting the ports in BIOS to AUTO
and forcing the standard values for com1 and 2
and I have verified that the serial ports are set for:
com1 irq 4 i/o 3f8
com2 irq 3 i/o 2f8
I know my way around serial ports.
Every other motherboard I have used under Windows 98SE has had no problems accessing the serial ports
under DOS.
I asked my dealer to try another K7T motherboard. He loaded Windows 98SE and could not access the serial
port in a DOS window either.
Is this something funny about K7T boards?
Do others have this problem?
This is a quite urgent problem. Please help.
Larry Alkoff

Larry,
You posted in the nVidia/AMD/SiS Forum instead of the Via Forum. I have moved you to the correct forum.
Good Luck,
Richard

Videocard to boot windows giving priority to the hdmi port, i need to DispayPort

Hello!
Yesterday bought a video card (N660 TF 2GD5/OC) and found such problem:
Go to the video card connected:
My TV: Samsung is connected via HDMI and my monitor: Dell is connected via DisplayPort
Video card to boot windows giving priority to the hdmi port. My tv I have to constantly keep it turned on to use the BIOS of the motherboard.
After loading windows become a priority monitor - as it should be. And to boot the operating system - my TV and I constantly have to turn it on in order to see the download PC.
Need a priority on my monitor. What do I do? Thank you very much for your earlier for the help!

Yes, IF you picked the right partition, as in the Boot Camp partition. If everything is done right you should be able to boot into the Mac side.
If you already booted into Windows and are at the point of installing the Boot Camp Drivers your already done installing Windows! Yea! All you need to do is just install the drivers and everything should work normal.
The Windows partition and the Mac partition are seen as two different HD's now as far as the computer knows.
You can use the Boot Camp control panel in Windows to boot into the Mac side and the Startup Disk in System Preferences on the Mac to switch to Windows. If you can't then press and hold down the Option key untill you get the boot screen.

Help - K7T266Pro2 won't access serial ports in DOS window

My K7T266Pro2 won't access serial ports in a DOS window under Windows 98SE.
Windows programs can access the ports but no DOS programs - including my modem program, banking program, Tapcis Compuserve program and MDMDR a serial port diagnostic program.
I have tried both setting the ports in BIOS to AUTO
and forcing the standard values for com1 and 2
and I have verified that the serial ports are set for:
com1 irq 4 i/o 3f8
com2 irq 3 i/o 2f8
I know my way around serial ports.
Every other motherboard I have used under Windows 98SE has had no problems accessing the serial ports
under DOS.
I asked my dealer to try another K7T motherboard. He loaded Windows 98SE and could not access the serial
port in a DOS window either.
Is this something funny about K7T boards?
Do others have this problem?
This is a quite urgent problem. Please help.
Larry Alkoff

Larry,
You posted in the nVidia/AMD/SiS Forum instead of the Via Forum. I have moved you to the correct forum.
Good Luck,
Richard

Need to remove Windows 7 parallels but on an OSX 10.8.5 environment

I purchased parallels for windows on the mac and it was a bad decision given that I did not end up using it much and want to get rid off it but now i have upgraded my OS to OSX 10.8.5 and that is not compatible with Windows 7 - how do i remove the parallels software. Can someone please advise?

You are mistaken with respect to your statement "...now i have upgraded my OS to OSX 10.8.5 and that is not compatible with Windows 7". Running Windows in Parallels is independent of OSx version. There is no "incompatibility" between Windows 7 and OSx 10.8.5. Depending on your Parallels version there may be an incompatibility between Parallels and your OSx version. If so, just upgrade Parallels.
Parallels stores its guest operating system as a file. Just remove the virtual mahine file by moving it to trash.

RV016 with 3 WAN Connections - Windows Messenger Intermittent problems.

I have a RV016 Router with 3 internet DSL conections.
Firmware version : 3.0.0.1-tm (Jun 6 2008 20:17:06)
LAN IP : 192.168.11.254 /24
WAN1 IP : 192.168.1.253 /24
WAN2 IP : 192.168.2.253 /24
WAN3 IP : 192.168.3.253 /24
MODE: Gateway.
Windows Messenger continually connects and disconnects. This behavior is permanent
I only have problems with Messengers (all releases), web page access is correct.
I check bandwith saturation and It's ok, I use less than 50% of each DSL.
I configured the correct size of MTU for each DSL and the problem continues.
Is there any way to set priority to this service?
Is there any way to check if the "load balance mode" affect this kind of connections?
I appreciate any idea.

Changing the DSL connections to bridge mode is part one of the solution. When they weren't in bridge mode, they were also acting as gateways/routers, probably also doing NAT.
Now that they are in bridge mode, the rv016 has control of the connections and the routing. Now that it has control, you can make the appropriate changes.
I ran into a similar issue as yours when I had an rv082 at one of my businesses. I had to access the state's web site to file sales taxes online. But their system detected when my router used a different WAN connection than the one I logged in on, so it would kick me off each time the router used both WAN connections. I could enable only one WAN connection each time I used their system (which would also work in your case with messenger), but that wasn't a real solution.
For you the solution will be a port trigger range. (For me the solution was to bind that destination site to a WAN connection.) Go to Setup-->Forwarding in the rv016 web management. You will see a section for port triggering at the bottom. Here's a link to a site that goes more into detail on the ports that need to have triggers on them:
http://www.electrictoolbox.com/article/networking/open-firewall-msn-icq/
I don't have messenger setup, so I don't know the ports off-hand. This setup should allow any system connected (just as they are now) to properly use messenger.
Let me know if you need any more help.

Bootcamp -Must Data for be loaded twice for windows and Mac to access it ?

f i use Bootcamp and Parallels on my iMAc, do i need to copy my Data (All documenst,music,video,s pictures, Applications and Programs ) Twice on my Hard Disk ? My Windows Data amounts to around170 GB - so does this mean I will have to Copy the 170 Gb Data Twice on my iMac which makes it Double ? (340 gb ) ? or can i access my Widnows data files from my Mac OS and Widnows without copying it twice ?.

cyrusdubash wrote:
f i use Bootcamp and Parallels on my iMAc, do i need to copy my Data (All documenst,music,video,s pictures, Applications and Programs ) Twice on my Hard Disk ? My Windows Data amounts to around170 GB - so does this mean I will have to Copy the 170 Gb Data Twice on my iMac which makes it Double ? (340 gb ) ? or can i access my Widnows data files from my Mac OS and Widnows without copying it twice ?.
If you have a Boot camp partition that you are accessing from within Parallels (you told Parallels to use your Boot camp partition as the virtual machine) then all your Windows programs and data reside in your Boot camp partition. So whether you access your Windows files from Boot camp or from within Parallels you are accessing the same files. For example, if you booted into Boot camp and edited a picture using a Windows program then saved the picture, and later you opened Parallels and accessed the same picture, you would open the same edited picture you saved when booted into Boot camp.
I'm sorry if I did not understand your question.
the hatter is always one step ahead of me. I'm sorry I was composing my reply while you posted. I did not see your post otherwise I would not have jumped in. I'll need to learn to post faster.
Message was edited by: BobTheFisherman

Windows server 2008 R2 Access files from anywhere

I want to make windows server 2008 R2 access from anywhere. I will install window server. It will basically be a file server and I want to access it from anywhere. Can you provide some steps that should be done . there is need to have a public IP or without
public IP it can be done?
Thanks in advance.

Hi
You will need to have a public IP Natted to your internal IP. be aware you dont want to expose this server too much to the internet, make sure you only have your ISP open certain ports on the firewall or if you are hosting your own TMG server for example
publish it through there.
Hope this helps. Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

Hello Forum, you need a serial ports for software icprog to program EPROM and Pic

Hello Forum, you need a serial ports for software icprog to program EPROM and Pic.I was wondering if this or a similar card is compatible with my Lenovo Desktop h50-50 --> -> PCI-E 2 serial ports and 1 parallel port PCI-Controller Card 3 Port ► http://fli.zz.mu/cut/scheda-pci-e-2-porte-seriali-1-porta-parallela .
My my Lenovo Desktop h50-50 upgrade to win 10, If it is not compatible to win 10. I could use it too virtualizing win Xp? Thank since TIME FOR ANSWERS, I apologize for my bad English.
THANK Joe

Unfortunately, no Sanyo phones are iSync compatible so you will not be able to synchronize your Contacts and Calendars with the phone.
Also, you may have problems with the Bluetooth adapter you purchased, as the only one officially supported by Apple for use with Macs is the D-Link DBT-120.
The Official Apple list of iSync compatible devices is here:
http://www.apple.com/macosx/features/isync/devices.html
It's always a good idea to check this list before purchasing a new phone.
Other phones are supported by third party plugins from here and here. But still no Samsung, Sanyo, LG etc. who all use thier own proprietary syncing protocols rather than the industry standard SyncML. These manufacturers also don't provide Mac software with their phones like the do for Windows users.
I'm afraid you're not going to have much luck if you stick with the Sanyo. I would seriously consider taking it back and swapping it for one of the handsets on the above linked pages. Personally I would recommend a Sony Ericsson model. I've always had excellent Mac compatibility with those.

Is there ANY way to install windows (for parallels) WITHOUT a superdrive?

I have Parallels (build 5600) and Win XP running fine on my iMac.
I want to run it on my MBA, too.
I have successfully installed Parallels (on a new trial license for now), and when I went to install Windows, learned that it can't be done via Remote Disk.
I'd really rather not spend $100 on an external drive JUST for this purpose.
Can I make a disk image of the windows disk?
Or connect to the imac in target disk mode (or something?!) to use THAT drive?
Or... can I somehow just copy my "virtual machine" from the imac to the MBA? Not sure if that will cause windows serial number police to freak, though...
Glancing through a quick search here, it seems it's possible to migrate the virtual machine. But what files, exactly, do I need to migrate? Just the .hdd file?
I'd prefer to do a nice clean install from the CD, but I don't know if that's possible.
Any help is appreciated!
Thanks!

Ok, I may have answered my own question.
I am copying my Virtual Machine from my imac, but it will take a long time to copy, and takes 10gb of space, so trying that is a last resort.
in the meantime I found this on the parallels site. Looks like you CAN use a disk image. I'm going to try it now- fingers crossed!
http://kb.parallels.com/en/4826
I'm using Macbook Air and cannot install Windows to Parallels Virtual Machine by means of CD/DVD drive “borrowing” feature. What should I do?
RESOLUTION
Unfortunately Macbook Air CD/DVD drive “borrowing” feature doesn’t support direct media streaming and thus cannot be used to install Windows (or any other Guest OS ) to Parallels Virtual Machine. To install a Windows VM on Macbook Air you can either create an .iso image of Windows installation disk on some other computer with CD/DVD drive and copy it to Mac or use an external CD/DVD drive that Apple offers for Macbook Air.
Please refer to this article for the instructions on how to create an .iso image for Parallels VM on Mac - http://kb.parallels.com/entry/32/458/

How can I obtain a complete Time Machine backup (about 300 GB), with Windows 7-Parallels Desktop, without the system re-booting automatically?

I have been operating my MacBook Pro 15" (Mac OS 10.7.5), with Windows 7 - Parallels Desktop, for about one and one-half years. However, whenever I execute a Time Machine back-up, and leave the system to complete the process, I return only to find that my system has re-booted, long before the back-up is completed. I do not use the auto-backup feature because I do not see how to change the shedule for backups away from the default schedule of hourly backups (too my stain on performance). Is there something that I am missing in setting up for such a back-up? I am currently operating away from home, using wi-fi for Internet access.
Appreciatively, Arbyem

I have been operating my MacBook Pro 15" (Mac OS 10.7.5), with Windows 7 - Parallels Desktop, for about one and one-half years. However, whenever I execute a Time Machine back-up, and leave the system to complete the process, I return only to find that my system has re-booted, long before the back-up is completed. I do not use the auto-backup feature because I do not see how to change the shedule for backups away from the default schedule of hourly backups (too my stain on performance). Is there something that I am missing in setting up for such a back-up? I am currently operating away from home, using wi-fi for Internet access.
Appreciatively, Arbyem

Windows messenger & parallels need access to port 1503

Similar Messages

Maybe you are looking for