Windows not booting after Winclone

Hi Guys,
I have a MBP and I have just installed a new 1TB HD. I successfully cloned the osx drive and restored it and all aplications are working fine. I then bought winclone. Cloned the boot camp and restored it. When I tried to boot into windows it said there is a boot failure. Hardware has changed. Im running windows & pro.
I have followed every thep outlined. I have gone from a 300 to 700gb partition from windows. As far as I understand thats what winclone does. Does anyone have any advice?
It will be greatly appreciated.
Thank you
Warren

Haviing the same processor socket would sortof help limit to differences in motherboard, but moving to a different motherboard is always (was) a disaster 95% of the time.
There are commercial programs to take a windows image, on a Windows system! and adjust the drivers when importing a new Windows image.
Tools for importing physical and virtual back and forth, but with Windows already present.
And with Macs by "same processor family" that is also likely to be safer.
Sounds like a lot of really good work went into WinClone in the end.
It was so slow, and during backup image creation unlike say Paragon and Acronis or Ghost, that is when you also scan for and detect system errors, bad sectors being read and insure you have and know you have a good image - and not when you go to restore. Though a sucessful restore is the best "test."
Would be nice if the backup was incremental.
If all you have is core Windows OS then it will be under 30GB so small (Blue-Ray would be nice here).
Now to see how soon WinClone supports Windows 8 RC which will be harder, based on changes in Windows system extra partitions and that even Paragon is not certified to work and listed as "incompatible."

Similar Messages

Windows not booting after install (iSCSI)

Hi all,
I am attempting to boot a host over iSCSI but have run into a brick wall trying to get my host to boot after successfull install of the OS.
Without changing the service profile I am able to install and boot VMWare ESX fine. Windows just does not seem to boot.
I can see the iSCSI subsystem is working ok when I connect to the adapter:
SUNINT0001PB-A# connect adapter 4/5/1
adapter 4/5/1 # connect
adapter 4/5/1 (top):1# at
attach-fls attach-mcp
adapter 4/5/1 (top):1# attach-mcp
adapter 4/5/1 (mcp):1# is
iscsi_get_config iscsi_ping
adapter 4/5/1 (mcp):1# iscsi_get_config
vnic iSCSI Configuration:
vnic_id: 6
          link_state: Up
       Initiator Cfg:
     initiator_state: ISCSI_INITIATOR_READY
initiator_error_code: ISCSI_BOOT_NIC_NO_ERROR
                vlan: 0
         dhcp status: false
                 IQN: iqn.1992-08.cisco.com:irfjmp0003pb
             IP Addr: 10.250.137.214
         Subnet Mask: 255.255.255.0
             Gateway: 0.0.0.0
          Target Cfg:
          Target Idx: 0
               State: ISCSI_TARGET_READY
          Prev State: ISCSI_TARGET_DISABLED
        Target Error: ISCSI_TARGET_NO_ERROR
                 IQN: iqn.1992-08.com.netapp:sn.1574897996
             IP Addr: 10.250.137.9
                Port: 3260
            Boot Lun: 0
          Ping Stats: Success (20.486ms)
        Session Info:
          session_id: 0
         host_number: 0
          bus_number: 0
           target_id: 0
Regards
Adam

Now it gets even stranger. As suspected the configuration is correct as I now have it booting into windows.
The strange part is, all was working ok until I applied all current updates, then it went into windows recovery mode and can't find my partition for recovery (only option I have is to reboot)
Have no idea what happened, so I re-installed. Re-installed ok, but the same problem as before, no boot volume found.
Re-installed again, but this time I released the windows boot media from the virtual CDROM drive while it was rebooting.
Windows booted sucessfully.
Very Strange.

Windows not booting after reinstalling Mavericks

I had some trouble with Mavericks after an update, so i had to reinstall. After doing so Bootcamp is no longer working.
I've used target disk mode to check that windows actually is there, and it is. The Bootcamp partition is also showing like
it should in startup disk. It just won't boot. I get a black screen with a message saying that there's no bootable device found.
Is there a way to fix it, or do i have to backup as much as possible and reinstall windows 7?
Please help!

Can you boot the Mac, with the Bootcamp issues, into OSX properly?
A. If yes, can you post the text output of the following Terminal commands.
diskutil list
diskutil cs list
sudo fdisk /dev/disk0
sudo gpt -vv -r show /dev/disk0
Please enter your password when prompted. Remove any personal information as you see fit.
B. If TDM is available, you can do the same set of commands from the functional Mac which can see the TDM disk with the malfunctioning BC installation.

HP Pavilion 15-n268sa will not boot after windows update (windows 8.1)

After a series of windows update (windows 8.1) my HP Pavilion 15-n268sa will not boot up, no fan noises, no lights no nothing.
I have tried a "hard reset" a number of times with no success.
When the battery is present the white LED flashes 3 times when the power button is pressed.
Please please help.

Hello Cuffy,
Welcome to the HP Forums!
I understand you notebook will not boot after a series of Windows updates.
Can you tell me if you are able to access the HP Recovery Manager by repeatedly tapping the F11 key while the notebook turns on? If you can access this, try doing a system restore to before you installed the updates. If not I would suggest you go through this document: Computer Does Not Start and the LEDs Blink or the Computer Beeps.
If it's the Caps Lock light that is blinking this document will tell you exactly what the error is (spoiler: 3 beeps is a memory failure). This could also explain the failed updates. The updates are stored in the RAM before being applied to the operating system.
You can try reseating the RAM, or using only 1 of the RAM cards, as you have 2x4GB cards. If it still doesn't work with 1 card, try the other card to confirm it has failed.
You can replace defective cards via HP Phone Support if covered under warranty or at the HP Part Store if not covered. You can contact HP Technical Support at 1-800-474-6836 in North America. For all other regions click here.
Hopefully this information helps!
Please click the "Kudos, Thumbs Up" at the bottom of this post if you want to say "Thanks" for helping!
Please click "Accept as Solution" if you feel my post solved your issue, it will help others find the solution.
The Great Deku Tree
I work on behalf of HP.

My Laptop B490 not booting after bios update

My laptop not booting after updating bios i used windows 8 OS.
I downloaded Bios from following link.
Bios Download Link
After updating bios, system restarted automaticaly, after that only power led is glowing, screen stays blank.
Help me solve it.
Solved!
Go to Solution.

hi sathish291
Welcome to the Forums.
Can you try the following:
1. Power down the machine, remove the AC adapter and battery.
2. Hold the power button for 30secs and reconnect the AC adapter only then turn the computer ON.
If the machine still doesn't power up normally and boot into WIndows then it's likely that something went wrong (could be a bad BIOS flash or an internal component might have gone defective during or after the BIOS update). In this case, you may need to contact lenovo on how to go about getting the unit serviced.
Support phone list
Regards
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Mac Mini will not boot after Security Update 2008-007

Hello,
A G4 Mac Mini machine I was asked to take a look at will not boot after the owner (succesfully) installed Security Update 2008-007 from Software Update. Booting always hangs at the blue screen after the Apple logo, and booting in verbose mode reveals that WindowServer is crashing repeatedly. Permissions and filesystems have been repaired, PRAM reset, etc. Safe boot also exhibits the same problem, but it is possible to boot to single user mode. Hardware checks out fine with diagnostic utilities.
Any suggestions on how to fix this? Unfortunately, backups are not available (it's not my machine =).

Hi Arkku , and a warm welcome to the forums!
I'd certainly give Sig's advice a try first.
If that should fail...
applesetupdone...
This was Posted by: JoseAranda at September 9, 2006 3:48 AM
"OK, restart your computer, hold down Command-s and type in the following:
/sbin/fsck -fy Enter
/sbin/mount -uaw Enter
rm /var/db/.applesetupdone Enter
# The rm command is the remove command which deletes the file.
# Robert: I'd rename the file via: mv /var/db/.applesetupdone /var/db/.applesetupdone.old
reboot Enter
Once you've done that the computer reboots and it's like the first time you used the machine. Your old accounts are all safe. From there you just change all other account passwords in the account preferences!!
end of posted by: JoseAranda"
Reset OS X Password Without an OS X CD...
http://theappleblog.com/2008/06/22/reset-os-x-password-without-an-os-x-cd/

MacBook Pro will not boot after software update

MacBook Pro will not boot after doing an Apple Software Update (of course they will not help you). MONEY, MONEY, MONEY is the name of the game. They can cause your computer to crash and still charge you!
Does anyone have an answer to why my computer is showing a little gear spinning for hours? I have tried several things with NO luck.
Thanks-

Run through the list of fixes here
Step by Step to fix your Mac

Not Booting after recent Security Patch/Java update

My wife has experienced what many have experienced with the recent update.
MacBook not booting after update (i.e. - "I have no name!")
I have tried everything posted on this topic since 2/13/09, but without any success. Does anyone have the fix for this yet?
Things I have tried:
* I can boot in safe mode (holding "Shift" while restarting)
* I cannot boot from an install disk(s) (holding C while restarting) - I have both a black one from purchase, and two gray ones with purchase from MiniMac
* Booting with verbose - gets stuck at same place as everyone else
Operating in safe mode:
* I can run DU and "repair" drive
* I can see and access the CD/DVD
* I cannot see drive in target drive mode (doesn't ever connect the 2 systems)
* I downloaded the update files from apple and reinstalled them individually (via USB ext Drive) with a reboot in between
* I attempted to update & archive, but I cannot run install CD from any systems disks (see above)
Has anyone figured out how to fix this yet?

Same problem than the other guy who is not mentioning the update in the title.
Powerbook 1.67.
System log said "No user defined computer name" and "using blah blah name" or so.
Mac Os X report (for apple) says:
Unresolved kernel trap(cpu 0): 0x300 - Data access DAR=0x000000003900FF1C PC=0x00000000008FC020
Latest crash info for cpu 0:
Exception state (sv=0x4299D280)
PC=0x008FC020; MSR=0x00009030; DAR=0x3900FF1C; DSISR=0x40000000; LR=0x008FE348; R1=0x2C47B9F0; XCP=0x0000000C (0x300 - Data access)
Backtrace:
0x008FE348 0x008E0014 0x002E9A80 0x002EB94C 0x0008C248 0x00029234
0x000233F8 0x000ABEAC 0xFF9BA29B
Kernel loadable modules in backtrace (with dependencies):
com.apple.ATIRadeon9700(4.1.8)@0x8d8000
dependency: com.apple.iokit.IOPCIFamily(1.7)@0x48d000
dependency: com.apple.iokit.IOGraphicsFamily(1.4.2)@0x85a000
dependency: com.apple.iokit.IONDRVSupport(1.4.2)@0x87e000
Proceeding back via exception chain:
Exception state (sv=0x4299D280)
previously dumped as "Latest" state. skipping...
Exception state (sv=0x43D0D000)
PC=0x9000AF48; MSR=0x0200F030; DAR=0x0ECA77FE; DSISR=0x42000000; LR=0x9000AE9C; R1=0xBFFFD6C0; XCP=0x00000030 (0xC00 - System call)
Kernel version:
Darwin Kernel Version 8.11.0: Wed Oct 10 18:26:00 PDT 2007; root:xnu-792.24.17~1/RELEASE_PPC
panic(cpu 0 caller 0xFFFF0003): 0x300 - Data access
Latest stack backtrace for cpu 0:
Backtrace:
0x000954F8 0x00095A10 0x00026898 0x000A8204 0x000ABB80
Proceeding back via exception chain:
Exception state (sv=0x4299D280)
PC=0x008FC020; MSR=0x00009030; DAR=0x3900FF1C; DSISR=0x40000000; LR=0x008FE348; R1=0x2C47B9F0; XCP=0x0000000C (0x300 - Data access)
Backtrace:
0x008FE348 0x008E0014 0x002E9A80 0x002EB94C 0x0008C248 0x00029234
0x000233F8 0x000ABEAC 0xFF9BA29B
Kernel loadable modules in backtrace (with dependencies):
com.apple.ATIRadeon9700(4.1.8)@0x8d8000
dependency: com.apple.iokit.IOPCIFamily(1.7)@0x48d000
dependency: com.apple.iokit.IOGraphicsFamily(1.4.2)@0x85a000
dependency: com.apple.iokit.IONDRVSupport(1.4.2)@0x87e000
Exception state (sv=0x43D0D000)
PC=0x9000AF48; MSR=0x0200F030; DAR=0x0ECA77FE; DSISR=0x42000000; LR=0x9000AE9C; R1=0xBFFFD6C0; XCP=0x00000030 (0xC00 - System call)
Kernel version:
Darwin Kernel Version 8.11.0: Wed Oct 10 18:26:00 PDT 2007; root:xnu-792.24.17~1/RELEASE_PPC

HT4623 iPhone 4s will not boot after trying to install ios7 beta 4. Stops at apple logo with progress line under it. how can I reset it or get it back up to do a restore then try the iOS 7 beta 4 install again. Issue was probably caused by disconnection

iPhone 4s will not boot after trying to install ios7 beta 4. Stops at apple logo with progress line under it. how can I reset it or get it back up to do a restore then try the iOS 7 beta 4 install again. Issue was probably caused by disconnection

Obviously since you have iOS 7 you're a developer. As a developer, you signed a NDA with Apple not to discuss the iOS on a public forum. Please log in to the Developer Forum using your credentials and ask for help there, lest you risk having your credentials terminated.
Thanks, and best of luck to you.
GDG

Macbook Pro Will Not Boot After Full Timemachine Restore

Hope someone can help. I upgraded my HD and attempted to restore from time machine. Everything appears to have worked well and the restoration was a success according to what the computer says. However, when I go to reboot I hear the startup sound then the apple pops up on the screen followed by a kernal panic error and the black box telling me that I need to hold down the start button and restart. I've tried resetting the pram, reinstalling from TM again and a couple of other things but it won't start up. I tried doing a clean install and it worked fine then I migrated files from my TM backup and that worked fine as well. However, that's not what I'm looking for, I wanted to get the machine exactly the way it looked before the upgrade and I thought TM was supposed to do that. I've read other forums were people have done it with no problems and am completely stumped at why it is not working. If anyone can shed some light I'd appreciate it.

I booted with the CD and after selecting the language, went to the utilities pane and used the partition feature.
Last night in desperation, I booted back to the CD and once again told it to do a full restore from TM. This was the third time that I had done it so far. The previous two times I had gone into the partition feature and partitioned the drive first. This time I skipped that step and just told it to restore from TM. It said if it did this it would erase everything on the drive. I agreed and let it do its work. This morning it once again, as in both previous times, said it had restored from TM successfully. I told it to restart and lo and behold, it booted and everything is just as I had it on the other drive.
Needless to say, I'm confused but happy. I just wish I knew why it would not boot after restoring the previous two times? Maybe it just wanted me to spend more money:) I tried booting today only after I had gone to frys electronics and bought a SATA to USB cable and cloning software.
Anyway, thanks for your help and if anyone knows why it wouldn't boot, let me know. It would be good to know for the future just in case. For anyone else having this trouble, keep trying. Third time was a charm for me.

My mac mini does not boot, after backing the enire system onto an external drive with Carbon Copy Clone

My Mac Mini does not boot, after backing the enire system onto an external drive with Carbon Copy Clone. I had switched the start-up disk back to the original of course. Now all I see is the Apple logo. What should I do? Thanks in advance.

Try disconnecting any external devices, especially hard drives
and try rebooting.
If that doesn't help, then :
If you are running Lion, boot to the Recovery HD and run a
Repair Disk on the OSX partition.
If Snow Leopard, boot to the installl DVD and run Repair Disk.
Also, you may want to bookmark this:
http://reviews.cnet.com/8301-13727_7-57345273-263/troubleshooting-the-boot-proce ss-for-intel-macs/?tag=txt;title
for future reference. It is a pretty good explanation of the
Mac boot process and how to identify where problems may be.

Power Book G 4 wil not boot after oz update Snow leapard os

Power book G4 did not boot after Lastesat Mozilla update, Runing snow leapard, message updatenis not compatable with computer tried to delete update, and will not boot from then on?

You can't run Snow Leopard on a PowerBook G4.
Please straighten your story out.

My mac book pro is not booting after sleep

My mac book pro is not booting after sleep...Pls anyone help me!!!

Hello adibah2731,
We've an article that proivdes a host of useful tips that can get your Mac booting up again.
Troubleshooting: My computer won't turn on
http://support.apple.com/kb/TS1367
Cheers,
Allen

Windows 8.1 Pro will not boot after installing iTunes 11.1.5.5

It's a little hard for me to accept that this is true, but the symptoms seem to be pointing the direction of the title of this thread. I have an all-in-one touch-screen Gateway computer that came with windows 7 (yeah, a win7 machine that came with touch, yeesh) and I put windows 8.1 pro 64-bit on it with a clean install (actually windows 8 was the clean install and then I did the free microsoft store upgrade to 8.1). It has 4GB of RAM and has a Pentium Dual Core cpu @ 2.2 Ghz. It was running fine with the previous version of iTunes, but as soon as I updated to iTunes 11.1.5.5 (and there may have been other apple things that updated too (ie quicktime of course), the computer prompted me for a reboot and froze during the reboot process (before it even shut down). Then it had trouble booting into windows. I ran startup repair to no avail and decided to do a sytem restore. My most recent restore point was from a few weeks back, before iTunes was even installed at all on the machine. I went back to that point and the machine worked fine again. Then I installed iTunes 11.1.5.5 and the same exact problem occurred - it froze while shutting down after the iTunes install and then would not boot into windows 8. I did another system restore and have not put iTunes back on. The system is working fine. I'm going to try to find out if there's a way to download older versions of iTunes, so that I can install it, but the bigger issue here is: Is this a legitimate bug/incompatibility with some hardware or software or driver that I have on this computer? I run a computer support business so I know my way around but I don't have time to troubleshoot this from scratch. Anyone else seeing this? Apple employees...a little help here? Any input?

let it sit for about 30 min and still got nothing
I then did a "hard shutdown(just pressed power button till it turned off the computer)"
That may not have been long enough. But a "hard shutdown" would definitely have been construed as a problem due to the update.
Asus apparently is a known problem case...
http://blogs.msdn.com/b/usbcoreblog/archive/2013/10/19/help-after-installing-windows-8-1-the-superspeed-ports-of-my-asus-system-don-t-work.aspx
Link courtesy Darrell Gorter [MSFT] found here
"Windows 8 Keyboard and mouse not working"
http://social.technet.microsoft.com/Forums/en-US/w8itprohardware/thread/06e9b341-0619-4085-acbf-e2f0133ca428?outputAs=rss
(RSS given to avoid overhead of opening long thread for IE users)
Note that there may be useful tips for you in both of those threads' comments.
Robert Aldwinckle

Windows 7 x64 Professional does not boot after install

Hello.
I created a Windows 7 VM in Windows Server 2012 R2 Standard Hyper-V, all the installation process done successfully, but after installation, it failed to boot and shows a black screen, and didn't boot after it.
Following is the event log occurs.
'Win-7_QA-Testing' was faulted because the guest executed an intercepting instruction not supported by Hyper-V instruction emulation. If the problem persists, contact Product Support. (Virtual machine ID 5B827557-7009-4D83-AA7C-26A45651EC3A)
VmName
Win-7_QA-Testing
VmId
5B827557-7009-4D83-AA7C-26A45651EC3A
FailureCategory
<not a known problem>
InstructionByteCount
0
InstructionBytes
Rax
0x10
Rbx
0x80
Rcx
0x0
Rdx
0x80
Rsp
0x200
Rbp
0x6e08
Rsi
0x25da4a
Rdi
0x7da4a
R8
0x0
R9
0x0
R10
0x0
R11
0x0
R12
0x0
R13
0x0
R14
0x0
R15
0x0
Rip
0x9d
Rflags
0x10002
FpControlStatus
7F030000000000000000000000000000
XmmControlStatus
0000000000000000801F0000FFFF0000
Cr0
0x10
Cr2
0x0
Cr3
0x0
Cr4
0x0
Cr8
0x0
Xfem
0x0
Dr0
0x0
Dr1
0x0
Dr2
0x0
Dr3
0x0
Dr6
0xffff0ff0
Dr7
0x400
Es
0002000000000000FFFF000020009300
Cs
00000B0000000000FFFF000000B09F00
Ss
0002000000000000FFFF000020009300
Ds
0002000000000000FFFF000020009300
Fs
0002000000000000FFFF000020009300
Gs
0002000000000000FFFF000020009300
Ldtr
0000000000000000FFFFFFFF00000000
Tr
0000000000000000FFFF000000008B00
Idtr
000000000000FFFF0000000000000000
Gdtr
000000000000270000002B0000000000
Tsc
0x3b48531f8c6
ApicBase
0xfee00900
SysenterCs
0x0
SysenterEip
0x0
SysenterEsp
0x0
PendingInterruption
0x0
Any help will be appreciated.
Thanks

How many vCPU and how much RAM have you given the VM?
Are you using alt +F10 and going into the shell to format the VHD and prior to the installation?
Are you using media that has SP1 slip streamed into it?
Have you tried forcing the vm off and then back on again?
Brian Ehlert
http://ITProctology.blogspot.com
Learn. Apply. Repeat.
vCPU = 1
RAM = 2048MB
No, I haven't try formatting the VHD between the window installation. This is the first time I'm facing the issue. It is a simple windows 7 pre activated iso file, not powered by SP1. I have tried forcing the VM off and ON again, but simply i can't get the
window screen back. Whenever the VM malfunctioning like this, then it cannot be shut down from the Hyper-V directly, but to make the VM Turn Off manually.

Windows not booting after Winclone

Similar Messages

Maybe you are looking for