Windows not seeing Mac drive

I did a straight Finder copy of my entire iTunes folder to a FAT drive.
Then, I plugged in the FAT drive to XP. I went to the prefs and I told iTunes where to find the iTunes folder.
So far, so good, except: the songs are not showing in iunes. In fact, it is still using the iTunes folder on the C drive.
What am I doing wrong?

Hey Chris,
Thanks! I opened iTunes holding the shift key and received a special window asking me to choose existing library or create a library...I selected create a library because the existing lib was not available. I then selected create from a folder and then selected the correct folder in the E drive.
So basically what happened is this: iTunes imported all of the music to a new itunes folder on E:; not really a problem since there is room, but still probably not right.
Done! except now I cannot get the iPhone to see the music; can play it, can see the iPhone as normal. Arg.
Michael

Similar Messages

Windows 8 does not see hard drive on Satellite A200

Windows 8 does not see hard drive on A200.
How to install?

> with Vista works fine,
Does this mean that Vista is still installed or is HDD visible while Vista installation setup?
Some notebooks HDD controller needs SATA driver in order to be able to install system.
Sat A200 is a little bit older but I dont think the SATA driver is needed here to install Win 8.
I guess you didnt any SATA drivers to install the Vista right?
Set the BIOS to default and try to boot again using Win 8.

My new mac mini does not see usb drives, but in hardware info the usb is visible

my new mac mini does not see usb drives, but in hardware info the usb is visible
i'tried several usb flash drives even brand new ones, they are visible onder hardware info but they are not on the desktop nor in the finder.
what is wrong and doe anyone has a solution ?

It does not show up in disk utility, its only visible through systeminformation.
When you plug in the USB flash drive and then refresh systeminformation it becomes visible.
To remove it I shut down the computer because I cannot eject the USB device anywhere.
After starting up again when I have removed the flash drive it has gone from the systeminfo USB list.
By the way my USB mouse and keyboard are working fine, I also changed ports of these and they still keep on working so I don't think the USB ports are defect.
I guess it some kind software problem, and because I'm new to Apple I do not know much about it how to solve this.

HP DJ4645 scanner does not see Mac OS 10 Maverick and computer does not see scanner

HP DJ4645 scanner does not see Mac OS 10 Maverick and computer does not see scanner.
I installed drivers and software from the HP website. Printer works fine but scaner does not work over WiFi. I did not try over USB because printer and computer are not in same room.

Hi @mamedina ,
I see that you are not able to scan over the wireless network. I would like to help you resolve this issue.
Check the driver name that is installed for the printer. Make sure it shows just the printer's name.
Click the Apple menu and then click System Preferences. Click Printers & Scanners, highlight the printer name on the left side and on the right side of the screen it should show the printer's name. (Deskjet 4645)
If the full printer name isn't listed correctly, delete it and add the printer name back in from the list. Click the - sign to delete the driver and then click the + sign to add the driver, might have to click the drop down to select the printer's name to add it in.
I have provided a document to make sure the Scan to Computer is enabled. You will have to select 10.8, then Network Connection. A 'No Computer Detected' or 'Connection Error' Message Displays When Scanning for HP Officejet 4610 ...
If you are still not able to scan, then I would connect the printer to the computer by a USB cable to see if it is a network issue or the scan port might be blocked on the router. Unfortunately the printer isn't accessible in the same room, but this will rule out a software issue or a network issue. You can contact the router company to check and open these ports 9220/9500/427 on the router for scanning.
Please let me know the outcome.
Have a nice day!
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

I installed windows 7 in macbook pro. but its booting only by windows not by mac. how to enter in mac?i installed windows 7 in macbook pro. but its booting only by windows not by mac. how to enter in mac?

i installed windows 7 in macbook pro. but its booting only by windows not by mac. how to enter in mac?

Hold Option key when starting - that gives you the option to choose between startup disks.

My CD reader do not see mac applications, but only windows applications.

On the adobe CS CD is a windows application aswel a Mac application.
There is no automatic startup on my mac.
And I do not see any file for a setup (.dmg) or other file to install Adobe CS.
It looks my drive only sees the Windows files.
Who can help me to solve this problem?

Welcome to the Apple Support Communities
Do you see a pkg file in the disc? Open the pkg if you don't see the dmg package

I'm attempting to transfer files, address book, etc from an external hard drive to my new Mac-mini using migration assistant. The external drive is showing up on my desktop but Migration Assistant is not seeing the drive when searching for devices

I'm attempting to migrate files, address book, maile, etc to my new Mac Mini using an external hard drive and Migration assistant. I followed the instructions on using Migration Assistant to do this but Migration Assistant is not seeing the external drive, which is displayed on my desktop

I've been chasing this problem all afternoon. I had to reformat my internal drive on my MBP and reinstall Mountain Lion Start up assistant wouldn't see my extrnal drive with the Time Machine files on it. After many tries, I skipped the restore there and let the system boot. I could see my external drive from Finder and the files looked OK. I was told to use Migration Assistant and it had the same problem.
I saw a hint on one of these posts that the icon that you see and is label Macintosh HD is actually your backup disk and it is telling you that it has a copy of your internal Macintosh HD. I went ahead and told it to continue and it started to restore my apps, settings, and documents. It's been going for a couple of hours, and is close to being done. I expect to see my old system restored when it is finished.
Wish that Apple would put some type of note that it is seeing the backup. That is most confusing and seems to be a problem for lots of users.
It's been a month or so since your post Did your get it to work?

Windows xp not seeing mac mini during migration

Hi all,
I just set up a new mac mini for my in-laws, fast-forwarding them through 15 years of technology. However, the migration from Win XP is not as seamless as Apple promises. After all the installation, the mini saw the PC, but the Migration Assistant on the PC does not see the mini. What is there to do?
Some details:
--- I verified on my router that both computers are on my LAN.
--- If it matters, the Win XP and thus the Migration Assistant is in Hungarian, as is the Lion installation. Everything is up-to-date.
--- I tried a reboot on both machines.
--- I shut down on all firewalls for the migration.
--- There is no apparent security lockdown on my router that would cause the trouble. Apart from uPNP being turned off. Is that a problem? The mac saw the PC twice...
--- Actually, after the reboot, the mini did not see the PC anymore, and before the reboot, it could see two instances of the PC, but picking either did not help as the PC was still only "looking for the mac", with an endless progress bar.
I am happy to try any networking or Windows setup, I'm just out of ideas.
Thanks!
Laszlo

Thanks I figured it out.

New Airport Extreme (2014) does not see USB Drive

Just fired up my new 2014 Airport Extreme and attached a Toshiba 3 TB USB Drive. My new (late 2013 iMac) does not see the new drive in Disk Utility.
The Extreme works in all other ways; ie, as a router, as a wireless node.
It came to me formated as a Windows drive, so I attached it directly to my MacBook Pro (which saw the drive) and reformated it as a Mac Drive (Journaled, GUILD). It showed up just fine on the MacBook Pro desktop.
When I reattach it to the Airport Extreme, it still does NOT show up in Disk Utility on the iMac.
Help Please

When I reattach it to the Airport Extreme, it still does NOT show up in Disk Utility on the iMac.
That drive will not show up in Disk Utility on the Mac.....since the Toshiba hard drive becomes a network drive when it is attached the AirPort Extreme.
Disk Utility will not display a network drive. It will only display drives that are connected directly to your iMac via USB, FireWire, etc.
Check using AirPort Utility to see if the AirPort Exteme recognizes the drive.
Open AirPort Utility, click the AirPort Extreme icon, then click Edit
Click the Disks tab at the top of the next window that appears
The drive will appear here if it is recognized by the AirPort Extreme.
In the example below, my WD Drive is connected to the USB port on the AirPort Extreme.

Installer does not see hard drive, how do I mount

Initialized Hard Drive with current volume and as mac extended and zero'd out memory. This drive came out of a PC that had been out of whack and drive was partitioned wrong in the PC. It worked fine to load mac OS 9.2.2 and has 18 gigs free. When I boot off of the Tiger disc it does not see the hard drive at all. Neither does the disc utility function. I checked the firm ware and it is up to date. Ran disk warrior and it says all is ok. Is it something simple?
I can't figure out what it is I have over looked. Thanks

Try this instead:
1a (If this is the startup drive.) Boot from your OS X Installer Disk. After the installer loads select Disk Utility from the Installer menu (Utilities menu if using Tiger.) Be sure to use the installer disk for the version of OS X you intend to install.
1b (If this is a non-startup volume or external drive.) Open Disk Utility in the Utilities folder of your Applications folder.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
3. Set the number of partitions from the dropdown menu (use 1 partition unless you wish to make more.) Set the format type to Mac OS Extended (Journaled, if supported.) Click on the Partition button and wait until the volume(s) mount on the Desktop.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled, if supported.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process will take 30 minutes to an hour or more depending upon the drive size.
If this is the second drive in your computer, be sure you have jumpered the drive as SLAVE (assuming the original hard drive is jumpered as MASTER.)

Does not see optical drive

My IMac does not see the optical drive, however, it is visibable in windows 7. I'm running Parallels

Exactly. It can only be connected to one at a time. You have to eject it from Parallels for it to be used by the Mac.
I initially thought you were using Boot Camp.

Time Machine will not see USB drive attaced to AEBS

I am having some difficulty getting Time Machine to see a USB attached Lacie drive. I can get it to mount through the finder, but Time Machine will not see it. It also works fine through a direct firewire connection. I have all of the current updates. Any help is appreciated.

have you tried formatting the drive, by selecting the disk or volume and using extended (journal). If the drive use to be a PC drive, you need to also give it a new index table. To give it a new table, you got to go to the partition section and use the option button. There will be 3 types, the GUID table is for intel macs, the 2nd selection is for PPC macs, and the third is for Window/Dos. You want to use to GUID table. After the table is set, format the disk using extended (journal).

Bridge CS4 Does Not See External Drive

Very suddenly, Bridge is not seeing the external USB connected driver I use to store recent photos. I read a similar message here and the writer was told to add the drive to favorites. That appeared to work for him, but I could not do that since the folder doesn't appear under Computer in the favorites section either. The drive appears in Windows Explorer. I am using Vista 32. Any suggestions?
Fran

Did you power up or connect the external drive after Bridge had been started? I've observed that Bridge only includes drives that were attached and active when Bridge was launched; it does not add a drive to its folders list if that drive is started after Bridge is active. With your external drive on (and appearing in explorer) try exiting and relauching Bridge.

PowerBook G4 does not see optical drive in System Profiler

I have a very strange situation in a powerbook G4 (1.67ghz, hi-res 15" screen).
I bought the laptop non-working, installed a new power board (plug on old one was fried!) Installed a 250gb HD which I had installed OSX on in another G4 laptop, and it booted up fine, or so I thought.
When I put in my Leopard install DVD to install over the existing 10.4 Tiger, the disc spun up, but would not mount - would not eject - and when I checked the System Profiler the superdrive was not recognized by the powerbook as being present on the ATA bus. The hard drive, of course, was seen on the ATA bus.
I thought the superdrive was bum, so I installed a known-working combo drive I had around from a previously parted laptop (Apple branded) and experienced EXACTLY the same situation.
Other things I have tried included using jumpers to manually set the hard drive to slave and cable select (from the factory, with no jumpers, it is set to master), thinking that perhaps the optical drive was somehow seen as master or cable select. All possible jumper settings I tried made no difference.
Booting from external firewire hard drive shows exactly the same situation on the ATA bus, EXCEPT (and this is where it gets just weird enough to pique my curiosity and keep me trying to fix it) - When I boot from the external drive WITHOUT AN INTERNAL DRIVE installed, the SUPERDRIVE SHOWS UP ON THE ATA BUS of the System Profiler! I have not yet seen both at the same time, but I can get one or the other to show, depending on, apparently, the presence of the internal hard drive.
Am I missing something here, or am I to assume a fault in the IDE controller of the logic board?
I have never seen this laptop working properly, but the seller I acquired it from stated that the optical drive worked fine until he fried the DC in-board, presumably with a faulty power supply. He had removed his hard drive to save the data on it.
Thanks for any help or clues that anyone might provide.
See another post with similar situation (archived, or I would have jumped on that thread):
http://discussions.apple.com/thread.jspa?threadID=1862129&tstart=0
Ray

Well, I am happy to report that the situation is resolved with my powerbook not seeing the superdrive, but I still do not really understand exactly why it was unavailable in the system profiler as I originally posted.
My particular solution was to wipe out (erase) the hard drive, zapped PMU, zapped PRAM, did the reset-nvram in open firmware, rechecked to make CERTAIN the proper cables were installed properly, and Now I just completed a fresh install of Leopard from the previously recalcitrant superdrive, to the now-clean hard drive.
My BEST GUESS as to what was wrong with the situation from the outset may have had something to do with where the hard drive came from and how that operating system was installed. (the OS was on the HD when I installed it) In hindsight, perhaps doing all the resets, as well as repairing permissions MIGHT have done it, but I got caught up in thinking it might be cables or something.
So, I would advise others with a similar problem to:
repair the hard drive
repair permissions on the hard drive
reset PMU
reset PRAM
boot to open firmware (hold command-option-o-f at boot) and type "reset-nvram" (without quotes) enter, the type "set-default" enter, then type "reset-all" enter
cross your fingers, knock on wood, and boot! See what happens....
if no glory, THEN look at cables (make certain they are the CORRECT cables and that they are seated properly) I bought a hard drive cable and an optical cable from ebay sellers with assurance that they were the proper cables, and NEITHER had the same part number as the original cable which I suspected faulty, and that in the end are actually GOOD! GO BY PART NUMBERS! do not accept someone elses assurance that their cable is the proper one!
then suspect faulty optical drive - if possible swap another drive in and check.
if a second optical fails, then SUSPECT logicboard, but before you invest in a new logic board ($$$$$) try putting a freshly erased HD in and just see if that helps.
good luck to you all with your mac troubleshooting!
and thanks to all who read and pondered....
I will mark this case "answered" though it is more closed than truly answered.
I am very relieved that the fault did not lie in any of the major components (or even the minor ones for that matter)
It turned out to be only software/installation/settings, even though the symptoms certainly seemed to point to a hardware issue. It pays to try the resets and repairs!
Ray

PRESARIO V2000T WINDOWS NOT RECOGNIZING DVD DRIVE

I HAVE COMPAQ PRESARIO V2000 (XP) (DZ 667AV) WITH A PIONEER DVDRW-DVRK15 AND WINDOWS NO LONGER RECOGNIZES DRIVE. DEVICE MGR MESSAGE=Windows cannot load the device driver for this hardware. The driver may be corrupted or missing. (Code 39). USED DRIVER DETECTIVE FOLLOWING IS A PARTIAL MESSAGE: (1327)This error has several causes. One cause is that the installation was created with a hard-coded path to a drive letter that does not exist on the machine. If this is the case then there is no way to make the installation install to a different drive letter. The software vendor must be contacted. SUPPORT FROM HP IS EXPIRED FOR MY LAPTOP. WILL A DRIVER DOWNLOAD WORK AND WHERE DO YOU SUGGEST I FIND THE WINDOWS DRIVER?
RBSTL

Ho boy! We have had several problems in recent threads with this dvd drive that I call the drive from the twilight zone. As I recall, it usually ended up a drive replacement, which is very painless and only costs $31. See:
Install video: http://eshop.macsales.com/tech_center/installation.cfm
Drive selection: http://eshop.macsales.com/shop/optical-drives/superdrives/powermac/
If you check previous threads and then decide to change drives, there it is.

Windows not seeing Mac drive

Similar Messages

Maybe you are looking for