Windows OS Provioning Isuue w/ Cisco IAC SE 3.0.1

Hi All,
I have a pretty sharp Partner in Brazil who is having an issue provioning Windows with IAC SE 3.0.1.
They can provision Linux and ESX hosts via CSP. Has anyone encoutered this issue before? Is it a known bug?
Here is the issue;
Drew,
We tried to install Windows using CSP or templates, but we had problems with both.
Because CSP is an OEM, maybe we could work with templates only. This type of provisioning is important for us.
Using templates we were able to deploy VMs with Windows 2008 R2. The CPO informs "succesful" status, but the OS is not customized with the IP address (plus mask and gateway) or the password for admin account that we choose on portal.
We observed the whole process at the orchestrator and noticed a weird behavior at the end: right after the NIC installation, the next step should be the NIC configuration. That step is OS dependent and there are 3 possible Branches in the flow: windows,linux and unknown. For some reason the orchestrator takes us to the unknown branch where no NIC configuration does not happen.
Regards,
Pedro Morgado

This sounds almost like http://www.cisco.com/en/US/customer/products/ps11869/products_tech_note09186a0080bcb900.shtml
However, we'd need to see the XML sent from CP to PO to be sure that it's the same case

Similar Messages

Ethernet controller driver not installing after Windows Server 2008 installation on Cisco UCS blade

I am using MDT 2010 to deploy Windows Server 2008 to a Cisco UCS B200 blade. The OS and hotfixes install with no problem. The system reboots and attempts to connect to the deployment share to continue with the task sequence and I receive an error stating
"A connection to the deployment share could not be made. The following networking device did not have a driver installed. PCI\VEN_1137&DEV_0043&SUBSYS_00481137&REV_A2"
The driver in question is the driver for the Ethernet controller for the UCS blade. More specifically, it is the network driver for the Palo card in the UCS Chassis. When I Ignore or Abort the install, I am able to manually install the driver and restart the
task sequence. The build then completes successfully with no further issue. I just cannot seem to automate the driver install. Has anyone dealt with this type of issue?

Vik and stealthfield - thank you for your responses.
I was preparing a script to manually move the driver into the c:\windows\inf location when I had to stop to create a new task sequence for a different build. It was while building this task sequence that I found the soulution to the problem.
In the Post Install -> Inject Drivers step of the Task Sequence, I noticed that it was executing a command of type "Inject Drivers" with a selection profile of "All Drivers" and "Install only matching drivers
from the selection profile" selected.
I changed this to run a command of type "Run Command Line" and specified that it execute "%Scriptroot%\ZTIdrivers.wsf". I noticed that this was selected in one of my other builds that was working properly, so I thought I'd
give it a try. - IT WORKED.
So to sum up, the solution was to change the type of command being executed in the "Post Install -> Inject Drivers" step of the task sequence. After this change, the machine came up and continued the task sequence with no further issues.
Thanks again for the responses - They were helpful and I do appreciate it.

Cisco IAC 3.1 - problems running Conf Wizard

Hi all
Following the configuration guide for Cisco IAC 3.1, I have all steps required for executing the configuration wizard in place but, for some reason, it fails to discover the infrastructure items through the wizard. I could discover and register the infrastructure items through the Manage Cloud Infrastructure portlet.
During the discovery process, I should expect communications between CP and CO, right? I see no new process starting at PO during the discovery process.
Any hints on what might be happening ?
Thanks in advance

Yes. The documentation actually indicates that PowerCli is a requirement. It is installed along with all the other requirements.
I believe this conf wizard issue comes from the SE 3.0.1 release. It was know that one had to log out, close the browser and then log back in so that the next wizard step could be performed. Terrible for a UI experience but hope it will be fixed soon.
Thanks for your support.

Seeing continous "Windows Account Locked" alert in Cisco IPS

Hi,
Can any one have any idea on why we are seeing huge number of "Windows Account Locked" alert in Cisco IPS device towards only one Windows server.
We checked whether Windows server is generating any malicious traffic by scanning the server but nothing is found
Feb 23 2011 20:05:47
Windows Account Locked
Cisco Intrusion Prevention System
Feb 23 2011 20:05:32
Windows Account Locked
Cisco Intrusion Prevention System
Feb 23 2011 20:04:47
Windows Account Locked
Cisco Intrusion Prevention System
Feb 23 2011 20:04:32
Windows Account Locked
Cisco Intrusion Prevention System
Feb 23 2011 20:03:47
Windows Account Locked
Cisco Intrusion Prevention System
Feb 23 2011 20:03:32
Windows Account Locked
Cisco Intrusion Prevention System
Feb 23 2011 20:02:47
Windows Account Locked
Cisco Intrusion Prevention System
Feb 23 2011 20:02:32
Windows Account Locked
Cisco Intrusion Prevention System

Mustafa,
Here are the signature details:
http://tools.cisco.com/security/center/viewIpsSignature.x?signatureId=5605&signatureSubId=0&softwareVersion=6.0&releaseVersion=S262
This signature detects a Windows SMB user account that has been locked on the Windows server due to multiple failed logon attempts, via the "STATUS_ACCOUNT_LOCKED_OUT" message returned to the client.
This signature severity is set by default to 'informational'
Hence all the signature is doing is leeting you know some users were locked out due to multiple logon attempts.
The event details will also reveal victim ip which might be the machine on which the logon attempts were tried.
Let me know if this addresses your concern.
- Sid

Windows 2k8 Radius Server with Cisco Wireless Controllers

We currently are using a Cisco 4400 wireless controller with an older Cisco Secure ACS appliance that is going EOL. My hope was to just connect our 4400 Wireless Controller to a Windows Server 2008 Radius Server (Just using Microsoft's Network Policy Server) but have not had any luck in getting this to work. Does anyone have an easy to follow set of instructions on configuration of Microsoft Windows Server 2008 NPS for use with Cisco Wireless Controllers? Any advise would be greatly appreciated.
Thank You,
Jim

Hi NPT,
Here is the post which may help you!!
https://supportforums.cisco.com/message/3073519
Regards
Surendra

Window 8 WiFi problem with Cisco wireless network

Anyone encounter a Windows 8 WiFi authentication problem with Cisco wireless network?
We are using WLC 5508, 7.2.111, and AP 3602i with WPA2.
Sent from Cisco Technical Support iPad App

This problem occurred with Soney, and Dell models. Lenovo with Windows 8 factory installed is working fine.
Won't make any difference as these laptop's wireless NIC cards are different.
Can you try with OPEN authentication. If the Sony and/or Dell laptop works, then you start cranking up the security and/or encryption settings until you break them.
I'm with Scott here: It's got to be a wireless NIC card driver.
As what George has stated, post the debug of the failed attempts.

SMTP for Cisco IAC 3.1

Hi all
Where do I change the smtp server information in a portal which is already installed and running?
Regards
/O
Otavio Augusto

Locate the file
C:\jboss-as-7.1.1.Final\standalone\deployments\RequestCenter.war\WEB-INF\classes\config\newscale.properties
Change the value for
ObjectCache.email.host
From M. Dupont:
It is also critical to set the actual return email address. In 3.1 this is done in the System Setup portal page in the System Settings tab. There is a task named Set System Email Account.

Cisco IP Communicator not working in Windows 7

Hi,
We upgraded our windows OS from XP to Windows 7. Since then Cisco IP Communicator is not working through VPN. With in office it works fine.
The IP Communicator get registered and we are able to hear the dial tone, but when the call connects no Voice.
Pls suggest.
Regards
Jagadish

Yes, i have tried that also and also audio port range. Strange is call shows connected but no voice from both ends.
This works perfectly fine with XP Machine. Only with Windows 7 machine it doesn't work. Disabled the windows firewall also and check. But no luck.

Cisco vpn client issue on windows 8.1 pro

I am using Cisco RV325-k9 router, I am configure "Easy vpn" in this router.
Our some users use Windows 7 pro and others users use Windows 8.1 pro with Cisco vpn client version 5.0.070290.
Issue is VPN client connected but not access remote machine and ping on windows 8.1 pro machines. but Working fine on windows 7 pro.
But When i am using wifi through MTS wifi usb device then working fine.
Please find the attached screenshot of VPN Client Statistics.
Please give me a solution.
Regards
Sanjib

Hi Sanjib,
Cisco VPN clinet is not supported for the windows version 8.1. And also it is EOL announced. Might be the below mentioned work around might help you. Try this.
http://www.vmwareandme.com/2013/12/solved-windows-8-and-windows-81-cisco.html#.U9tCdxCrOxo
Regards
Karthik

Window size of MSS Reporting IAC's

Hi experts,
Is there any way to control the window size of the MSS reporting IAC's? I'm implementing Webdynpro on EP 7.0, ECC 6.0. Right now I choose a report from the list, click Define Selection Criteria, select employees, then Report Result. The resulting window is considerable smaller, and when I maximize it, my report stays the smaller size, with scroll bars. If I click print preview it expands to full screen, but how can I get it that way to start with??
Any help is appreciated!
Brenda

Hi Brenda,
Check the parameters for service HRWPC_FC_EXEC in transaction SICF to ensure you have at least those specified in note 969401.
We have the parameters set as follows:
~TRANSACTION                                HRWPC_FC_EXEC
~WEBGUI_SHOW_SYSTEM_MODAL   0
~WEBGUI                                                1
~NOHEADEROKCODE                1
~SINGLETRANSACTION                1
~WEBGUI_THEME                                SL
We had the same problem with the old MSS report launchpad in 4.6C, but since upgrading to ECC 6.0 we now use the newer webdynpro report launchpad, and although I haven't found a way to control the size of the new window, maximising the window seems to also expand the report contents.
Regards,
John

Cisco ISE AD (Windows Server 2013) Authentication Problem

Background:
Deployed two Cisco ISE 1.1.3. ISE will be used to authenticate wireless users, admin access to WLC and switches. Backend database is Microsoft AD running on Windows Server 2012. Existing Cisco ACS 4.2 still running and authenticating users. There are two Cisco WLCs version 7.2.111.3.
Wireless users authenticates to AD through ACS 4.2 works. Admin access to WLC and switches to AD through ISE works. Wireless authentication using PEAP-MSCHAPv2 and admin access wtih PAP/ASCII.
Problem:
Wireless users cannot authenticate to AD through ISE. The below is the error message "11051 RADIUS packet contains invalid state attribute" & "24444 Active Directory operation has failed because of an unspecified error in the ISE".
Conducted a detailed test of AD from ISE. The test was successful and the output seems all right except for the below:
xxdc01.xx.com (10.21.3.1)
Pinged:0 Mins Ago
State:down
xxdc02.xx.com (10.21.3.2)
Pinged:0 Mins Ago
State:down
xxdc01.xx.com
Last Success:Thu Jan 1 10:00:00 1970
Last Failure:Mon Mar 11 11:18:04 2013
Successes:0
Failures:11006
xxdc02.xx.com
Last Success:Mon Mar 11 09:43:31 2013
Last Failure:Mon Mar 11 11:18:04 2013
Successes:25
Failures:11006
Domain Controller: xxdc02.xx.com:389
    Domain Controller Type: Unknown DC Functional Level: 5
    Domain Name:            xx.COM
    IsGlobalCatalogReady:   TRUE
    DomainFunctionality:           2 = (DS_BEHAVIOR_WIN2003)
    ForestFunctionality:           2 = (DS_BEHAVIOR_WIN2003)
Action Taken:
Log on to Cisco ISE and WLC using AD credentials. This rules out AD connection, clock and AAA shared secret as the problem.
2)     Tested wireless authentication using EAP-FAST but same problem occurs.
3)     Detailed error message shows the below. This rules out any authentication and authorization polices. Before even hitting the authentication policy, the AD lookup fails.
12304 Extracted EAP-Response containing PEAP challenge-response
11808 Extracted EAP-Response containing EAP-MSCHAP challenge-response for inner method and accepting EAP-MSCHAP as negotiated
Evaluating Identity Policy
15006 Matched Default Rule
15013 Selected Identity Store - AD1
24430 Authenticating user against Active Directory
24444 Active Directory operation has failed because of an unspecified error in the ISE
4)     Enabled AD debugging logging and had a look at the logging. Nothing significant and no clues to the problem.
5)     Tested wireless on different laptos and mobile phones with same error
6)     Delete and add again AAA Client/Devices on both Cisco ISE and WLC
7)     Restarted ISE services
8)     Rejoin domain on Cisco ISE
9)     Checked release notes of ISE 1.1.3 and WLC 7.2.111.3 for any open caveats. Nothing found related to this problem.
10)    There are two ISE and two WLC deployed. Tested different combination of ISE1 to WLC1, ISE1 to WLC2 etc. This rules out hardware issue of WLC.
Other possibilities/action:
1)     Test it out on a different WLC version. Will have to wait outage approval to upgrade WLC software.
2)     Incompatibility of Cisco ISE and AD running on Microsoft Windows Server 2012
Anyone out there experienced something similar of have any ideas on why this is happening?
Thanks.
Update:
1) Built another Cisco ISE 1.1.3 sever in another datacentre that uses the same domain but different domain controller. Thais domain controller is running Windows Server 2008. This works and authentication successful.
2) My colleague tested out in a lab environment of Cisco ISE 1.1.2 with Windows Server 2012. He got the same problem as described.
This leads me to think there is a compatibility issue of Cisco ISE with Windows Server 2012.

Does anyone know if ISE 1.1.3 p1 supports AD DCs running 2012, if not which patch is required ot version?
Worryingly when ISE joins a 2012 DC it states it's connected successfully, and if another 2003 DC is available in that datacentre it will perform the auths against that DC whilst actually advertising (Connections in the GUI) that it's connected to the 2012 DC. We ended up mapping 8 PSN IP’s to another datacentre which has one Win2003 servers whilst the old 2003 DC is being promoted back, the 8 ISE servers started working, even though they still advertised they were connected to the 2012 DCs in the original datacentre - I performed a leave and join on one PSN and only then did it advertise that the node was connected to a DC in a different datacentre

Windows 8 clients can't associate to Cisco 2125 controller

HI All,
I have 2125 controller with running IOS 7.0.230.0, now unable to connect windows 8.1 laptops.
It is support Windows OS 8.1 wireless clients, you need to upgrade the firmware to 7.0.250.X.. I think windows is latest version are supported or not. kindly confirm.
Thanks & Regards,
Johnson.

Hi Johnson,
Yes, You have to upgrade to your WLC code at least 7.0.235.0 or above if you are hitting this bug CSCua29504.
https://supportforums.cisco.com/document/113836/windows-8-clients-cant-associate-cisco-unified-wireless
HTH
Rasika
**** Pls rate all useful responses ****

Cisco DCNM 5.1(3u) - any particular version of Windows 2008?

The documentation does not specify any particular version beyond Windows 2008. 32bit vs 64bit, R1 or no R1?
Server System Requirements
Cisco DCNM Release 5.1(x) supports running the Cisco DCNM server on these operating systems:
•Microsoft Windows 2008 is supported in Cisco DCNM Release 5.1(3u)
http://www.cisco.com/en/US/docs/switches/datacenter/sw/5_x/dcnm/release/notes/dcnm_5_1_relnotes.html#wp61633
I have to get the thing buit for me by another team and I don't want to have to go back to them to get it "fixed" etc.

Hi,
DCNM is supported in all versions of Windows 2008 (both 32 and 64 bit) and also R1.
The latest version DCNM 5.2(1) is available for download now. It supports Catalyst 6500 switches and many more new features.

Cisco USB Driver for Microsoft Windows 7 PC?

Hello All,
I want a USB Driver for the USB Console cable which came up with Cisco Router.
Note that this USB Console cable has both the sides USB ports ( 1 side of the port goes to USB Console Port of Router and other side goes to USB port of your Laptop)
I searched on cisco.com.
Found the below link:
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst6880_x/hardware/installation/guide/b_c6880-X_hig/b_c6880-X_hig_appendix_01001.pdf
However, when I go to download link, it appears as "Page Not Found"
I want to try this option and connect my Laptop's HyperTerminal to Router's USB Console.
Does anyone know the USB driver for this?
Thanks
Chinar

Hi Chinar-
It looks like this will work with Windows 7.
http://software.cisco.com/download/release.html?mdfid=282867574&softwareid=282855122&release=3.1
DJ

Cisco CallManager Attendant compatible v1.3 with Windows 7?

I'm currently reviewing all software within my company to see if it is compatible with Windows 7 due t
o future upgrade of the OS we use.
I can not seem to find any info on this software, can someone please help with my question.
If this is not compatible then suggesting a compatible version or alternative would be of great help.
many thanks.

Hi
This document lists Windows 7 Compatibility:
http://www.cisco.com/en/US/prod/collateral/voicesw/ps6789/ps7046/ps7282/product_bulletin_c25-563280_ps5905_Products_Bulletin.html
Note that the consoles listed are no the standard CCM Attendant Console - as I understand it development of that has pretty much stopped (it's not supported for new installations) so whether or not Windows 7 official support materializes for that.. I wouldn't like to say.
Perhaps someone else can comment on whether the app actually works well on 7 or not?
Aaron

Windows OS Provioning Isuue w/ Cisco IAC SE 3.0.1

Similar Messages

Maybe you are looking for