Windows Server 2008 R2: Unable to add a subnet to Site and Services

Hi All,
I'm trying to add a new subnet to Site and Services to allow new server in that specific subnet to access the proper DC.
These are the actual subnet configured:
- 192.168.28.0/22
- 192.168.48.0/22
- 192.168.80.0/22
Now I want to add this subnet: 192.168.90.0/22
Why I cannot confirm this new subnet in the GUI?
Thanks

Hi,
Becasue the network prefix is improper.
If we use "/22" as the mask, the network prefix should be 192.168.4n.0/22 (n=0,1,2... ...).
Therefore the proper network prefix should be 192.168.88.0/22 or 192.168.92.0/22.
For detailed information about subnetting, please refer to the link below,
http://technet.microsoft.com/en-us/library/cc958834.aspx
Best Regards.
Steven Lee
TechNet Community Support

Similar Messages

Unable to install lan realtek rtl8101 and network controller driver on windows server 2008

Hi Guys,
i am trying to install realtek rtl 8101 f amily driver and network controller driver on windows server 2008 but unable to install.
Hp device Model.:- hp pavilion g4 1303au
Model no.:- 5c03213jsh
network controller Device ID: PCI\VEN_168C&DEV_0032&SUBSYS_1785103C&REV_01\4&211965BF&0&0020
Name: PCI Device
Device ID: PCI\VEN_10EC&DEV_5209&SUBSYS_3564103C&REV_01\4&34BC5A71&0&0030
Name: SM Bus Controller
Device ID: PCI\VEN_1022&DEV_780B&SUBSYS_3564103C&REV_13\3&2411E6FE&0&A0
thanks,
Amit Rai

Hi:
SMBus controller:
Here is what I have done...I have zipped up and attached below under Attachments, the raw smbus controller driver files for you to unzip and manually install.
Download and unzip the file.
Go to the device manager and click on the smbus controller needing drivers. Click on the driver tab. Click on Update Driver.
Select the Browse my computer for driver software option and browse to the driver folder that you unzipped.
Make sure the Include Subfolders box is checked and the driver should install. Then reboot.
Ethernet: Download and install the 1st driver on the list.
http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=14&PFid=7&Level=5&Conn=4&DownTy...
Card reader (PCI dev.): Download and install the first driver on the list.
http://www.realtek.com.tw/downloads/downloadsView.aspx?Langid=1&PNid=15&PFid=25&Level=4&Conn=3&DownT...
Wireless: You will have to try the Vista driver for the Atheros wireless card...
http://h20565.www2.hp.com/portal/site/hpsc/template.PAGE/public/psi/swdDetails/?sp4ts.oid=5060882&sp...
Attachments:
sp66185.zip ‏7 KB

Windows Server 2008 R2 problem

Hi there
I'm a newbie to Flash media server and I would like to explore its usage.
Does any one have experience with Flash Media Server 3.5.3 running on Windows Server 2008 R2? I installed FMS on my Windows Server 2008 R2, but the admin console cannot start.
By the way, I installed FMS on a Windows Server 2003 32-bit machine. And I'm able to use the admin console on Server 2003 to connect to the Server 2008 R2 installation.
Also, I have a separate disk that is used to hold the media content to be streamed via FMS. How can I configure FMS to use that disk as root for media file instead of using "c:\program files (x86)\...\webroot\vod"
Thanks very much in helping me to start the project.
Best Regards
Steve Yau

ForThanks very much for your prompt response.
For (1), if I start "Flash Media Administration Console" from the Start menu, an IE prompts up and it tries to open "c:\program files(x86)\Adobe\Flash Media Server 3.5\tools\fms_adminConsole.htm" with the following in the information bar:
"An add-on for this website failed to run. Check the security settings in Internet Options for potential conflicts"
I thought it was the problem of flash player that cannot be run on 64-bit IE, so i tried 32-bit IE, but still in vain. I also tried to install flash player using 32-bit IE on Windows server 2008 R2 but the installation cannot start.
The FMSAdmin service is surely running with firewall configured. I've also installed FMS on another Windows Server 2003 32-bit. There I can start the admin console and connect to the Windows Server 2008 R2 FMSAdmin service.
For (2), I've added the line as per your kind help. But my question will be: How can I test whether my FMS is correctly streaming the video? For Windows Media Service, I can easily open URL in WMP and the streaming can be verified easily. But I don't know how to test FMS setup from web client side. Any clues? For your information, I don't have Adobe Flash or Dreamweaver stuff.
Thanks again for your kind help
Regards
Steve Yau

Windows Server 2008 backups failing

I have a Windows Server 2008, fully patched that backups recently started to fail and now, we are unable to open the Windows Server Backup. Also unable to open Disk Management or any other applications requiring Virtual Disk.
Attempts to start VDS from service or command line result in the following errors:
1:
A timeout was reached (180000 milliseconds) while waiting for the Virtual Disk service to connect.
2:
The Virtual Disk service failed to start due to the following error: The service did not respond to the start or control request in a timely fashion.
I added the debuglog to registry and the $vds$.log only records the following:
(PID:8988,TID:10060,17:32:43) ERROR: CVdsLoader::LoadService, 3, hr=8007041D
I have also increased the timeout dramatically to no avail.
SFC /scannow returns:
Windows Resource Protection found corrupt files but was unable to fix some of them.
Nothing requiring Virtual Disk Service will operate making backups and imaging impossible.
Any thoughts?

Hi,
As SFC could find some issues (but fail to fix), please try to DISM could help as well:
DISM.exe /Online /Cleanup-image /Restorehealth
Fix Windows corruption errors by using the DISM or System Update Readiness tool
http://support.microsoft.com/kb/947821
Also though the following hotfix is not specific for this error, it helps updating VDS components. Please try it and see if issue persists after installing it.
Virtual Disk Service (VDS) crashes when you try to extend a dynamic volume in an NTFS file system on a computer that is running Windows Vista, Windows Server 2008, Windows Server 2008 R2, or Windows 7
http://support.microsoft.com/kb/975680
Please remember to mark the replies as answers if they help and un-mark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Windows server 2008 R2 and NFS mounted subdirectories.

I am mounting from a Windows Server 2008 R2 Box to a RHEL 6.3 machine and I am able see the folders; however, I am unable to see the sub-folders via the mapped NFS mount in windows. Any ideas as to why? Some additional facts are below.
1. We are using an NFS mount from Windows to RHEL (mount -o
\\RHELBOX\ops\resources R:) We NFS mount from RHEL to a Storage device - the fstab entry looks like this:
10.9.9.9:/vol/afpres1/psf_prod
/ops/resources/prod     nfs
_netdev,defaults
0 0
10.9.9.9:/vol/afpres1/psf_test
/ops/resources/test       nfs
_netdev,defaults
0 0
10.9.9.9:/vol/afpres1/baselib
/ops/resources/psf
nfs          _netdev,defaults
0 0
The RHEL export file looks like this.
/ops/resources 10.4.4.4(rw,sync,no_all_squash,insecure,nohide) (the 10.4.4.4 IP address is the of the 2008 r2 server
/ops/resources 10.4.4.5(rw,sync,no_all_squash,insecure,nohide)
/ops 10.4.11.66(rw,sync,no_all_squash,insecure,nohide)
#/ops/resources *(rw,sync,no_all_squash,insecure,nohide)
/opspool *(rw,sync)
2. We are not using Samba or CIFS

Hello,
The TechNet Sandbox forum is designed for users to try out the new forums functionality. Please be respectful of others, and do not expect replies to questions asked here.
As it's off-topic here, I am moving the question to the
Where is the forum for... forum.
Karl
When you see answers and helpful posts, please click Vote As Helpful, Propose As Answer, and/or Mark As Answer.
My Blog: Unlock PowerShell
My Book: Windows PowerShell 2.0 Bible
My E-mail: -join ('6F6C646B61726C40686F746D61696C2E636F6D'-split'(?<=\G.{2})'|%{if($_){[char][int]"0x$_"}})

Windows Server 2008 Ent to Windows server 2012 R2 std Migration

Dear All,
We have windows server 2008 x64 Ent with SP2 it's working fine and perfectly . Presently we implemented new data center also we installed windows server 2012R2 Std . we would like to migrate windows form old data center to new data center .
I would like to tell you my current setup :
we have Windows 2008 Ent SP2 server 3 number all are GC domain controller it's working perfectly .
IP Address : 192.168.33.121 , 192.168.33.122 , 192.168.33.123
we have more than 2000 domain users and PC's all clients PC's are using static IP with domain DNS
My new data center Server windows 2012R2 STD
Static IP : 192.168.200.115
Here my doubt :
1. How can we migrate
2. how can we assign new DNS address to all clients more than 2000 PC's
Please could you tell me best way to solve this issue ..
Best Regards
Subash

Hello
tip:
1 check all old application, server /like old Linux samba, exch2003/ to support 2012 dc
2 all firewall add same rule as old DC /if have domain trust open firewall./
3 prompt to dc and gc the new server
4 check DNS server /DNS forwarder if have/ and AD logs
5 run BPA for AD and DNS
6 create gpo or startup script to add/change dns settings on client.
sorry my english

Hp deskjet 2545 printer driver not supporting on windows server 2008 r2

I have purchased a 3 in 1 hp deskjet 2545 printer. I am trying to configure in on my home laptop (HCL) operating system: windows server 2008 R2, but unable to configure it. customer support executive told me hp deskjet 2545 printer driver is not compatible on windows server 2008 R2. but I have checked in my office and it is working fine on my office 2008 server. Please help.

Hello Arvindk,
Welcome to the HP Support Forums! I understand you are trying to use your HP Deskjet 2545 with your Windows Server 2008 R2. Because you are using a server your question will be best answered on the Commercial Forums: http://h30499.www3.hp.com/hpeb/
I was able to find this document for Installing the Printer Software on Windows Server 2003 or 2008, which may be helpful for you.
Thanks,
HevnLgh
I work on behalf of HP
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

Installation of Client Access role fails on Windows Server 2008 R2 (Execution of: "$error.Clear(); Install-ExchangeCertificate -services "IIS, POP, IMAP")

Hello
I am trying to install Exchange Server 2010 beta 1 onto a Windows Server 2008 R2 (build 7000) machine which has also been set up as a domain controller.
However when attempting to install the Client Access role, setup fails with the error below.
Does anyone know of a way to get around this please?
I have already searched for this error and not found any similar threads.
Also every time I press the code button on this forum it crashes the browser and I keep losing the message! (IE8 from within Server R2). Also the message box is very small, will not expand and keeps jumping to the top.
Thanks
Robin
[code]
Summary: 4 item(s). 1 succeeded, 1 failed.
Elapsed time: 00:00:01
Preparing Setup
Completed
Elapsed Time: 00:00:00
Client Access Role
Failed
Error:
The execution of: "$error.Clear(); Install-ExchangeCertificate -services "IIS, POP, IMAP" -DomainController $RoleDomainController", generated the following error: "Could not grant Network Service access to the certificate with thumbprint 2F320F5D5B5C6873E54C8AB57F604D8AFA31D18C because a cryptographic exception was thrown.".
Could not grant Network Service access to the certificate with thumbprint 2F320F5D5B5C6873E54C8AB57F604D8AFA31D18C because a cryptographic exception was thrown.
Access is denied.
Elapsed Time: 00:00:01
Mailbox Role
Cancelled
Finalizing Setup
Cancelled
[/code]
Robin Wilson

Hello
Thanks for all the replies.
I have since wiped the system and installed everything again and it all worked this time so not sure what was wrong last time. I did try to uninstall all Exchange components and then uninstall IIS and Application server, reboot and re-install but I received the same error still when it came to installing the client access role.
Walter: I just attempted the standard installation which should have used the default self-signed certificate. Everything was a fresh install done at the same time on a freshly formatted PC.
For info last time when it failed to work:
- Installed Windows Server 2008 R2
- Installed Domain Controller role using dcpromo. I set the forest and domain as Windows Server 2008 R2
- Added a forest trust between main domain and test Exchange domain (set up as ex2010.local)
- Installed IIS and Application Server role
- Installed Hyper-v role
- Installed Desktop Experience feature
- Installed Exchange and recieved the error
When it worked I set up the forest and domain in Windows Server 2008 mode (i.e. not R2), installed Exchange first and then set up the forest trust and then Hyper-v. It did say it failed to configure dns which was probably because it started trying to do automatic updates half way through the dcpromo! DNS seems to work ok though.
I did notice this time that Hyper-v gave a warning about the virtual network adapter not being set up correctly and the local network did not work correctly although I could access the internet. Not sure if this could have been related to the cause of the problem previously. For now I have disabled the virtual network until I get time to try and get it working and so the mail will work in the meantime.
I also noticed that Hyper-v added an extra 443 ssl binding to the default website so as it had 2 bindings on port 443 it refused to start. After deleting one it worked.
I decided to install Exchange onto a domain controller as it is only a test and I wouldn't do it in a live environment. I am also short of test machines! It didn't give me any warnings about this actually, I think previous versions warn you that it is not recommended.
Andreas and Chinthaka: I did not know about the requirement to run the domain at 2003 mode. The main domain is running in 2008 mode with Exchange 2007 so I assume this is just a temporary beta related requirement. It does seem to be working (second attempt) so far in a 2008 mode domain although I haven't had a chance to fully test it yet.
Thanks
Robin
P.S. Sorry it's taken me a while to reply!
Robin Wilson

Problem instaliing sun one LDAP server on windows server 2008 r2

Hi all ,
I am trying to install Ldap server (Sun ONE Directory Server) on windows server 2008
I am using apache-tomcat-7.0.28 and java jdk1.7.0_05
I am following this manual for installing :
https://blogs.oracle.com/marginNotes/entry/installing_directory_server_enterprise_edition1
I have a problem with the cacao agent and how to install it .
I've got this error message :
c:\Program Files\Sun\dsee7\bin>dsccsetup cacao-reg
Configuring Cacao...
## Failed to run "c:/Program Files/Sun/dsee7/ext/cacao_2/bin/cacaoadm.bat" set-
aram "jdmk-home=c:/Program Files/Sun/dsee7/lib/private"
#### Cannot create service for instance: [cacao.instance.name].
#### Cannot perform firstime inialisation and configuration.
## Exit code is 1
Failed to configure Cacao.
I stuck and with no other solutions . I hope if you could to help with this issue .
i will glad to know if there is any other ways to install this specific Ldap server ,
Thanks,
Alon

You most likely skipped the step of starting the installed server prior to trying to access admin URL. Please check this document:
http://docs.sun.com/source/817-1830-10/win.html
Relevant section is:
You can start the Administration Server in either of the following ways:
# Select Start Menu -> Programs -> Sun ONE Web Server, and choose Start Web Server Administration Server.
# From the Control Panel�s Services item.
HTH...

Windows Server 2008 R2 SP1 BSOD 0x1a with CLFS.sys

Hello,
I've got a BSOD on a Windows Server 2008 R2 with SP1 installed. Analyzed the dump and could
see a Bug-check of 0x1a which means "MEMORY_MANAGEMENT".
Further analysis on this dump shows me, that this probably is caused by the CLFS.sys, which
is the Common Log File System Driver. This CLFS.sys is installed with date:
Tue Jul 14 01:19:57 2009
I have now searched trough MS Support pages and resources and also the Internet, but I found no
information about an update for this or a newer version. It's nearby impossible to find newer versions
for specific files in i.e. Hot-fixes.
Do you know this issue with the 0x1a BSOD and CLFS.sys and/or do you know a newer version ?
Any help would be very appreciated!
Thanks and regards plus have a nice day !
Tino

Hi Tino,
Regarding to Bug Check 0x1A, please refer to following article.
Bug Check 0x1A: MEMORY_MANAGEMENT
Did you install any third-party application in this problematic server? Would you please let me know whether
the BSOD issue occurred regularly? Or just occurred suddenly? If the BSOD issue occurred regularly, please
perform a clean boot and check if this BSOD issue still exists.
In addition, please check if necessary updates need to be installed and drivers need to be updated. Please
run sfc /scannow command to scan all protected system files and check if find errors.
As you know, troubleshoot this kind of kernel crash issue, we need to analyze the crash dump file to narrow down the root cause of the issue. Actually, it is not effective
for us to debug the crash dump file here in the forum. If this issues is a state of emergency for you. Please contact Microsoft Customer Service and Support (CSS) via telephone so that a dedicated Support Professional can assist with your request.
To obtain the phone numbers for specific technology request, please refer to the web site listed below:
http://support.microsoft.com/default.aspx?scid=fh;EN-US;OfferProPhone#faq607
àThis CLFS.sys is installed with date: Tue Jul 14 01:19:57 2009
àor do you know a newer version?
By the way, I checked the CLFS.sys in a Windows Server 2008 R2 in my Lab environment. It also created in July
2009.
Hope this helps.
Best regards,
Justin Gu

Getting error while trying to install ADRMS role on Windows Server 2008 R2 SP1.

Hello,
I am trying to install ADRMS on Windows Server 2008 R2 SP1 (This machine also has domain controller and Exchange Server 2010 SP3 installed). But I am getting following error:
Install-ADRMS : The configuration object is read only, because it has been committed by a call to ServerManager.CommitChanges().
If write access is required, use ServerManager to get a new reference. at Microsoft.Web.Administration.Configuration.SetDirty()
Not sure what is causing this error. Any help to solve it would be appreciated.
Thanks.
Jigar Mehta

Hello,
I am trying to install ADRMS on Windows Server 2008 R2 SP1 (This machine also has domain controller and Exchange Server 2010 SP3 installed). But I am getting following error:
Install-ADRMS : The configuration object is read only, because it has been committed by a call to ServerManager.CommitChanges().
If write access is required, use ServerManager to get a new reference. at Microsoft.Web.Administration.Configuration.SetDirty()
Not sure what is causing this error. Any help to solve it would be appreciated.
Thanks.
Jigar Mehta

Blue screen when logging into windows server 2008 r2

when logging into windows server 2008 r2, all I have is a blue screen and the mouse.
I tried looking for solutions on the internet, then I found a microsoft hotfix "http://support.microsoft.com/kb/2590550" I run the hotfix in command line but it gave me nothing, no error or success messages.
I tried to reboot but I still have the same problem.
Is there any solution to this problem ??

Hi,
Thank you for posting in Windows Server Forum.
Did you face this issue during remote session or console session?
In addition, have you try to change or install any driver\software which cause this problem?
Have you use any debugging tools from Microsoft to find respective error cause?
You can refer following article for memory dump.
How to read the small memory dump file that is created by Windows if a crash occurs
http://support.microsoft.com/kb/315263/en-us
Hope it helps!
Thanks.
Dharmesh Solanki

Error when try to install exchange Server 2013 in windows server 2008 R2 Sp1

Hi
I'm getting these errors while trying to install Microsoft Exchange Server 2013 on my Windows Server 2008 R2 SP1 the user i'm using is the Administrator and it is already a member of "Enterprise
Admins" and "Schema Admins"
in my organization there is 6 Exchange server 2013 in 3 site windows server 2012 in this case
I have to install exchange 2013 in windows Server 2008 r2 sp1
the functional level 2008 R2 I getting these errors please help.
Errors:
This computer doesn't belong to a valid Active Directory site. Check the site and subnet definitions.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.InvalidADSite.aspx
Error:
A reboot from a previous installation is pending. Please restart the system and then rerun Setup.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.RebootPending.aspx
Error:
There is a pending reboot from a previous installation of a Windows Server role or feature. Please restart the computer and then run Setup again.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.PendingRebootWindowsComponents.aspx
Error:
You must be a member of the 'Organization Management' role group or a member of the 'Enterprise Admins' group to continue.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.GlobalServerInstall.aspx
Error:
You must use an account that's a member of the Organization Management role group to install or upgrade the first Mailbox server role in the topology.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.DelegatedBridgeheadFirstInstall.aspx
Error:
You must use an account that's a member of the Organization Management role group to install the first Client Access server role in the topology.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.DelegatedCafeFirstInstall.aspx
Error:
You must use an account that's a member of the Organization Management role group to install the first Client Access server role in the topology.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.DelegatedFrontendTransportFirstInstall.aspx
Error:
You must use an account that's a member of the Organization Management role group to install or upgrade the first Mailbox server role in the topology.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.DelegatedMailboxFirstInstall.aspx
Error:
You must use an account that's a member of the Organization Management role group to install or upgrade the first Client Access server role in the topology.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.DelegatedClientAccessFirstInstall.aspx
Error:
You must use an account that's a member of the Organization Management role group to install the first Mailbox server role in the topology.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.DelegatedUnifiedMessagingFirstInstall.aspx
Error:
Setup encountered a problem while validating the state of Active Directory: Could not find information about the local site. This can be caused by incorrect configuration of subnets or sites or by replication latency. See the Exchange setup log for more
information on this error.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.AdInitErrorRule.aspx
Error:
Either Active Directory doesn't exist, or it can't be contacted.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.CannotAccessAD.aspx

I think it's from subnet in site and services
have 3 site A,B,C and new site is "D"I have problem in "D" site
A subnet is 10.33.50.0/24 AD 2012 ,exchange 2013
B subnet is 10.35.50.0/24 AD 2012 ,exchange 2013
C subnet is 10.36.50.0/24 AD 2012 ,exchange 2013
D subnet is 10.100.100.0/25 AD 2008 ,exchange 2013 error when install it
find event error
The description for Event ID 6 from source MSExchange CmdletLogs cannot be found. Either the component that raises this event is not installed on your local computer or the installation is corrupted. You can install or repair
the component on the local computer.
If the event originated on another computer, the display information had to be saved with the event.
The following information was included with the event:
test-SetupPrerequisites
{Roles={LanguagePacks, Bridgehead, ClientAccess, UnifiedMessaging, Mailbox, FrontendTransport, Cafe}, LanguagesAvailableToInstall=True, DomainController=, CustomerFeedbackEnabled=True, ExchangeVersion=15.0.847.32, LanguagePackDir=D:\Exchange
Server Software, SufficientLanguagePackDiskSpace=True, ADInitError=Setup encountered a problem while validating the state of Active Directory: Could not find information about the local site. This can be caused by incorrect configuration of subnets or sites
or by rep, ScanType=PrecheckInstall, LanguagePackVersioning=True, HostingDeploymentEnabled=False, TargetDir=C:\Program Files\Microsoft\Exchange Server\V15, SetupRoles={LanguagePacks, AdminTools, Bridgehead, ClientAccess, UnifiedMessaging, Mailbox, FrontendTransport,
Cafe}}

Printing from OSX Lion Client to Windows Server 2008

I have tried these methods:
=============
via System Preferences
IP Printer (Line Printer Daemon - LPD)
Address (both Server Name and IP Address)
e.g. lpd://servername/queue
Queue
Print Using (HP LaserJet P4010 Series)
Result:
After a test print is sent, the print queue dialog reads:
Processing Job.
Copying Print Data.
Connecting to Printer.
Paused - "/usr/libexec/cups/backend/lpd failed"
**** I have also tried using the hostname in place of the IP address
I get something to the effect of:
D [10/Nov/2011:12:24:35 -0500] [Job 27] ------------------------------------------------------
D [10/Nov/2011:12:24:35 -0500] [Job 27] Pre-processing tasks:
D [10/Nov/2011:12:24:35 -0500] [Job 27] Line - %%BeginDocument     Processor - EmbeddedDocumentCounter     "Check for embedded document"     (pre, mandatory, substr)
D [10/Nov/2011:12:24:35 -0500] [Job 27] Line - %!PS-Adobe     Processor - EmbeddedDocumentCounter     "Check for embedded document"     (pre, mandatory, substr)
D [10/Nov/2011:12:24:35 -0500] [Job 27] Post-processing tasks:
D [10/Nov/2011:12:24:35 -0500] [Job 27] Line - %%Page:     Processor - PageAccounting     "Log page for accounting"     (post, mandatory, substr)
D [10/Nov/2011:12:24:35 -0500] [Job 27] ------------------------------------------------------
D [10/Nov/2011:12:24:35 -0500] [Job 27] Read 8170 bytes of print data...
D [10/Nov/2011:12:24:35 -0500] [Job 27] Wrote 8170 bytes of print data...
D [10/Nov/2011:12:24:35 -0500] [Job 27] Connecting to 10.157.32.92:515 for printer DOBL_24HR1
D [10/Nov/2011:12:24:35 -0500] [Job 27] Connecting to printer.
D [10/Nov/2011:12:24:35 -0500] [Job 27] Set job-printer-state-message to "Connecting to printer.", current level=INFO
D [10/Nov/2011:12:24:35 -0500] [Job 27] STATE: -connecting-to-device
D [10/Nov/2011:12:24:35 -0500] [Job 27] Connected to printer.
D [10/Nov/2011:12:24:35 -0500] [Job 27] Set job-printer-state-message to "Connected to printer.", current level=INFO
D [10/Nov/2011:12:24:35 -0500] [Job 27] Connected to 10.157.32.92:515 (local port 1009)...
D [10/Nov/2011:12:24:35 -0500] [Job 27] lpd_command 02 DOBL_24HR1
D [10/Nov/2011:12:24:35 -0500] [Job 27] Sending command string (12 bytes)...
D [10/Nov/2011:12:24:35 -0500] [Job 27] Reading command status...
D [10/Nov/2011:12:24:35 -0500] [Job 27] lpd_command returning 1
D [10/Nov/2011:12:24:35 -0500] [Job 27] Backend returned status 1 (failed)
D [10/Nov/2011:12:24:35 -0500] [Job 27] Printer stopped due to backend errors; please consult the error_log file for details.
D [10/Nov/2011:12:24:35 -0500] [Job 27] End of messages
D [10/Nov/2011:12:24:35 -0500] [Job 27] printer-state=5(stopped)
D [10/Nov/2011:12:24:35 -0500] [Job 27] printer-state-message="/usr/libexec/cups/backend/lpd failed"
D [10/Nov/2011:12:24:35 -0500] [Job 27] printer-state-reasons=paused
=============
via System PreferencesWindows *navigated to the server (e.g. smb://servername/printer/) with the browser.
Result:
After a test print is sent, i login to the dialog box with:
DOMAIN\USERNAME
PASSWORD
(*) Remember this password in my keychain
Status - On Hold (Authentication Required)
**** I have also tried various formats for the username here:
DOMAIN\USERNAME & password
USERNAME & password
SERVER\USERNAME & password
Here's the Log output:
D [10/Nov/2011:12:26:21 -0500] [Job 28] Queued on "DOBL_24HR1" by "lab".
D [10/Nov/2011:12:26:21 -0500] [Job 28] job-sheets=none,none
D [10/Nov/2011:12:26:21 -0500] [Job 28] argv[0]="DOBL_24HR1"
D [10/Nov/2011:12:26:21 -0500] [Job 28] argv[1]="28"
D [10/Nov/2011:12:26:21 -0500] [Job 28] argv[2]="lab"
D [10/Nov/2011:12:26:21 -0500] [Job 28] argv[3]="testprint"
D [10/Nov/2011:12:26:21 -0500] [Job 28] argv[4]="1"
D [10/Nov/2011:12:26:21 -0500] [Job 28] argv[5]="AP_ColorMatchingMode=AP_ApplicationColorMatching AP_D_InputSlot= collate com.apple.print.DocumentTicket.PMSpoolFormat=application/pdf com.apple.print.JobInfo.PMJobName=testprint com.apple.print.PrinterInfo.PMColorDeviceID..n.=3671 com.apple.print.PrintSettings.PMColorMatchingMode..n.=0 com.apple.print.PrintSettings.PMColorSyncProfileID..n.=1580 com.apple.print.PrintSettings.PMCopies..n.=1 com.apple.print.PrintSettings.PMCopyCollate..b. com.apple.print.PrintSettings.PMFirstPage..n.=1 com.apple.print.PrintSettings.PMLastPage..n.=2147483647 com.apple.print.PrintSettings.PMPageRange..a.0..n.=1 com.apple.print.PrintSettings.PMPageRange..a.1..n.=2147483647 fit-to-page media=Letter pserrorhandler-requested=standard job-uuid=urn:uuid:ad3091e2-399a-3964-4c78-b8a81bf25bdf job-originating-host-name=localhost time-at-creation=1320945980 time-at-processing=1320945980 PageSize=Letter"
D [10/Nov/2011:12:26:21 -0500] [Job 28] argv[6]="/private/var/spool/cups/d00028-001"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[0]="<CFProcessPath>"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[1]="CUPS_CACHEDIR=/private/var/spool/cups/cache"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[2]="CUPS_DATADIR=/usr/share/cups"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[3]="CUPS_DOCROOT=/usr/share/doc/cups"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[4]="CUPS_FONTPATH=/usr/share/cups/fonts"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[5]="CUPS_REQUESTROOT=/private/var/spool/cups"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[6]="CUPS_SERVERBIN=/usr/libexec/cups"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[7]="CUPS_SERVERROOT=/private/etc/cups"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[8]="CUPS_STATEDIR=/private/etc/cups"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[9]="HOME=/private/var/spool/cups/tmp"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[10]="PATH=/usr/libexec/cups/filter:/usr/bin:/usr/sbin:/bin:/usr/bin"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[11]="[email protected]"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[12]="SOFTWARE=CUPS/1.5.0"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[13]="TMPDIR=/private/var/spool/cups/tmp"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[14]="USER=root"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[15]="CUPS_SERVER=/private/var/run/cupsd"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[16]="CUPS_ENCRYPTION=IfRequested"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[17]="IPP_PORT=631"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[18]="CHARSET=utf-8"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[19]="LANG=en_US.UTF-8"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[20]="APPLE_LANGUAGE=en-US"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[21]="PPD=/private/etc/cups/ppd/DOBL_24HR1.ppd"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[22]="RIP_MAX_CACHE=128m"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[23]="CONTENT_TYPE=application/vnd.cups-banner"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[24]="DEVICE_URI=smb://utlab-prsrv-02/DOBL_24HR1"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[25]="PRINTER_INFO=DOBL_24HR1"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[26]="PRINTER_LOCATION="
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[27]="PRINTER=DOBL_24HR1"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[28]="PRINTER_STATE_REASONS=none"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[29]="CUPS_FILETYPE=document"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[30]="FINAL_CONTENT_TYPE=printer/DOBL_24HR1"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[31]="AUTH_I****"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[32]="AUTH_U****"
D [10/Nov/2011:12:26:21 -0500] [Job 28] envp[33]="AUTH_P****"
D [10/Nov/2011:12:26:21 -0500] [Job 28] Started filter /usr/libexec/cups/filter/cgbannertopdf (PID 7646)
D [10/Nov/2011:12:26:21 -0500] [Job 28] Started filter /usr/libexec/cups/filter/cgpdftops (PID 7647)
D [10/Nov/2011:12:26:21 -0500] [Job 28] Started filter /usr/libexec/cups/filter/pstops (PID 7648)
D [10/Nov/2011:12:26:21 -0500] [Job 28] Started filter /Library/Printers/hp/filter/hpPostProcessing.bundle/Contents/MacOS/hpPostProces sing (PID 7649)
D [10/Nov/2011:12:26:21 -0500] [Job 28] Started backend /usr/libexec/cups/backend/smb (PID 7650)
D [10/Nov/2011:12:26:21 -0500] [Job 28] Started smb backend (PID 7653)
D [10/Nov/2011:12:26:21 -0500] [Job 28] STATE: +connecting-to-device
D [10/Nov/2011:12:26:21 -0500] [Job 28] Connecting to printer...
D [10/Nov/2011:12:26:21 -0500] [Job 28] Set job-printer-state-message to "Connecting to printer...", current level=INFO
D [10/Nov/2011:12:26:21 -0500] [Job 28] Looking up "utlab-prsrv-02"...
D [10/Nov/2011:12:26:21 -0500] [Job 28] Failed to connect to "smb://<username>:<password>@utlab-prsrv-02/": STATUS_LOGON_FAILURE
D [10/Nov/2011:12:26:21 -0500] [Job 28] Set job-printer-state-message to "Authentication required", current level=ERROR
D [10/Nov/2011:12:26:21 -0500] [Job 28] smb backend (PID=7653) stopped with status 512
D [10/Nov/2011:12:26:21 -0500] [Job 28] smb backend will exit with status 2
D [10/Nov/2011:12:26:21 -0500] [Job 28] load_banner(filename="/private/var/spool/cups/d00028-001")
D [10/Nov/2011:12:26:21 -0500] [Job 28] hpPostProcessing launched
D [10/Nov/2011:12:26:21 -0500] [Job 28] Page = 612x792; 12,12 to 600,780
D [10/Nov/2011:12:26:21 -0500] [Job 28] cgpdftops - copying to temp print file "/private/var/spool/cups/tmp/01ddf4ecb23b2"
D [10/Nov/2011:12:26:21 -0500] [Job 28] Final document orientation - 0
D [10/Nov/2011:12:26:21 -0500] [Job 28] Setting language to en-US
D [10/Nov/2011:12:26:21 -0500] [Job 28] EWU support is absent for device.
D [10/Nov/2011:12:26:21 -0500] [Job 28] Pages per sheet - 1
D [10/Nov/2011:12:26:21 -0500] [Job 28] Orientation - portrait
D [10/Nov/2011:12:26:21 -0500] [Job 28] ------------------------------------------------------
D [10/Nov/2011:12:26:21 -0500] [Job 28] Pre-processing tasks:
D [10/Nov/2011:12:26:21 -0500] [Job 28] Line - %%BeginDocument     Processor - EmbeddedDocumentCounter     "Check for embedded document"     (pre, mandatory, substr)
D [10/Nov/2011:12:26:21 -0500] [Job 28] Line - %!PS-Adobe     Processor - EmbeddedDocumentCounter     "Check for embedded document"     (pre, mandatory, substr)
D [10/Nov/2011:12:26:21 -0500] [Job 28] Line - %%EndComments     Processor - DriverVersion     "Insert driver info"     (pre, mandatory, substr)
D [10/Nov/2011:12:26:21 -0500] [Job 28] Post-processing tasks:
D [10/Nov/2011:12:26:21 -0500] [Job 28] Line - %%Page:     Processor - PageAccounting     "Log page for accounting"     (post, mandatory, substr)
D [10/Nov/2011:12:26:21 -0500] [Job 28] ------------------------------------------------------
D [10/Nov/2011:12:26:21 -0500] [Job 28] Allowing document iterator to handle job termination...
D [10/Nov/2011:12:26:21 -0500] [Job 28] Using line-by-line file iteration...
D [10/Nov/2011:12:26:21 -0500] [Job 28] cgpdftops - using PPD file "/private/etc/cups/ppd/DOBL_24HR1.ppd"...
D [10/Nov/2011:12:26:21 -0500] [Job 28] PS Matching Mode = AP_ApplicationColorMatching
D [10/Nov/2011:12:26:21 -0500] [Job 28] cgpdftops - languageLevel = 3, mediaBox.size.width = 612, mediaBox.size.height = 792
D [10/Nov/2011:12:26:21 -0500] [Job 28] cgpdftops - documentMediaBox.size.width = 612, documentMediaBox.size.height = 792
D [10/Nov/2011:12:26:21 -0500] [Job 28] Page = 612x792; 12,12 to 600,780
D [10/Nov/2011:12:26:21 -0500] [Job 28] slow_collate=0, slow_duplex=0, slow_order=0
D [10/Nov/2011:12:26:21 -0500] [Job 28] Before copy_comments - %!PS-Adobe-3.0
D [10/Nov/2011:12:26:21 -0500] [Job 28] %!PS-Adobe-3.0
D [10/Nov/2011:12:26:21 -0500] [Job 28] %APL_DSC_Encoding: UTF8
D [10/Nov/2011:12:26:21 -0500] [Job 28] %APLProducer: (Version 10.7.2 (Build 11C74) Quartz PS Context)
D [10/Nov/2011:12:26:21 -0500] [Job 28] %%Title: (testprint)
D [10/Nov/2011:12:26:21 -0500] [Job 28] %%Creator: (cgpdftops CUPS filter)
D [10/Nov/2011:12:26:21 -0500] [Job 28] %%CreationDate: (Thursday, November 10 2011 12:26:21 EST)
D [10/Nov/2011:12:26:21 -0500] [Job 28] %%For: (lab)
D [10/Nov/2011:12:26:21 -0500] [Job 28] %%DocumentData: Clean7Bit
D [10/Nov/2011:12:26:21 -0500] [Job 28] %%LanguageLevel: 3
D [10/Nov/2011:12:26:21 -0500] [Job 28] %%Pages: 1
D [10/Nov/2011:12:26:21 -0500] [Job 28] %%BoundingBox: (atend)
D [10/Nov/2011:12:26:21 -0500] [Job 28] %%PageOrder: Ascend
D [10/Nov/2011:12:26:21 -0500] [Job 28] %%EndComments
D [10/Nov/2011:12:26:21 -0500] [Job 28] Before copy_prolog - userdict/dscInfo 5 dict dup begin
D [10/Nov/2011:12:26:21 -0500] [Job 28] Before copy_setup - %%BeginSetup
D [10/Nov/2011:12:26:21 -0500] [Job 28] Before page loop - %%Page: 1 1
D [10/Nov/2011:12:26:21 -0500] [Job 28] Copying page 1...
D [10/Nov/2011:12:26:21 -0500] [Job 28] pagew = 588.0, pagel = 768.0
D [10/Nov/2011:12:26:21 -0500] [Job 28] bboxx = 0, bboxy = 0, bboxw = 612, bboxl = 792
D [10/Nov/2011:12:26:21 -0500] [Job 28] PageLeft = 12.0, PageRight = 600.0
D [10/Nov/2011:12:26:21 -0500] [Job 28] PageTop = 780.0, PageBottom = 12.0
D [10/Nov/2011:12:26:21 -0500] [Job 28] PageWidth = 612.0, PageLength = 792.0
D [10/Nov/2011:12:26:21 -0500] [Job 28] Calling processor EmbeddedDocumentCounter before line %!PS-Adobe-3.0
D [10/Nov/2011:12:26:21 -0500] [Job 28] Calling processor DriverVersion before line %%EndComments
D [10/Nov/2011:12:26:21 -0500] [Job 28] Task "Insert driver info" complete. Processor - DriverVersion. Line - %%EndComments
D [10/Nov/2011:12:26:21 -0500] [Job 28] Received SIGPIPE
D [10/Nov/2011:12:26:21 -0500] [Job 28] Wrote 1 pages...
D [10/Nov/2011:12:26:21 -0500] [Job 28] Backend returned status 2 (authentication required)
D [10/Nov/2011:12:26:21 -0500] [Job 28] Job held for authentication.
D [10/Nov/2011:12:26:21 -0500] [Job 28] End of messages
D [10/Nov/2011:12:26:21 -0500] [Job 28] printer-state=3(idle)
D [10/Nov/2011:12:26:21 -0500] [Job 28] printer-state-message="Authentication required"
D [10/Nov/2011:12:26:21 -0500] [Job 28] printer-state-reasons=none
==============
via CUPS (localhost:631)here is the syntax of my printer addresses:
SAMBA--
smb://username:password@serverhost/printer
smb://username:password@serverip/printer
smb://serverhost/printer
smb://serverip/printer
I get something like...
"/usr/libexec/cups/backend/smb failed"
D [10/Nov/2011:12:39:00 -0500] [Job 29] Before copy_comments - %!PS-Adobe-3.0
D [10/Nov/2011:12:39:00 -0500] [Job 29] %!PS-Adobe-3.0
D [10/Nov/2011:12:39:00 -0500] [Job 29] %APL_DSC_Encoding: UTF8
D [10/Nov/2011:12:39:00 -0500] [Job 29] %APLProducer: (Version 10.7.2 (Build 11C74) Quartz PS Context)
D [10/Nov/2011:12:39:00 -0500] [Job 29] %%Title: (testprint)
D [10/Nov/2011:12:39:00 -0500] [Job 29] %%Creator: (cgpdftops CUPS filter)
D [10/Nov/2011:12:39:00 -0500] [Job 29] %%CreationDate: (Thursday, November 10 2011 12:39:00 EST)
D [10/Nov/2011:12:39:00 -0500] [Job 29] %%For: (lab)
D [10/Nov/2011:12:39:00 -0500] [Job 29] %%DocumentData: Clean7Bit
D [10/Nov/2011:12:39:00 -0500] [Job 29] %%LanguageLevel: 3
D [10/Nov/2011:12:39:00 -0500] [Job 29] %%Pages: 1
D [10/Nov/2011:12:39:00 -0500] [Job 29] %%BoundingBox: (atend)
D [10/Nov/2011:12:39:00 -0500] [Job 29] %%PageOrder: Ascend
D [10/Nov/2011:12:39:00 -0500] [Job 29] %%EndComments
D [10/Nov/2011:12:39:00 -0500] [Job 29] Before copy_prolog - userdict/dscInfo 5 dict dup begin
D [10/Nov/2011:12:39:00 -0500] [Job 29] Before copy_setup - %%BeginSetup
D [10/Nov/2011:12:39:00 -0500] [Job 29] Before page loop - %%Page: 1 1
D [10/Nov/2011:12:39:00 -0500] [Job 29] Copying page 1...
D [10/Nov/2011:12:39:00 -0500] [Job 29] pagew = 588.0, pagel = 768.0
D [10/Nov/2011:12:39:00 -0500] [Job 29] bboxx = 0, bboxy = 0, bboxw = 612, bboxl = 792
D [10/Nov/2011:12:39:00 -0500] [Job 29] PageLeft = 12.0, PageRight = 600.0
D [10/Nov/2011:12:39:00 -0500] [Job 29] PageTop = 780.0, PageBottom = 12.0
D [10/Nov/2011:12:39:00 -0500] [Job 29] PageWidth = 612.0, PageLength = 792.0
D [10/Nov/2011:12:39:00 -0500] [Job 29] Calling processor EmbeddedDocumentCounter before line %!PS-Adobe-3.0
D [10/Nov/2011:12:39:00 -0500] [Job 29] Calling processor DriverVersion before line %%EndComments
D [10/Nov/2011:12:39:00 -0500] [Job 29] Task "Insert driver info" complete. Processor - DriverVersion. Line - %%EndComments
D [10/Nov/2011:12:39:00 -0500] [Job 29] Current page number is 0
D [10/Nov/2011:12:39:00 -0500] [Job 29] Calling processor PageAccounting after line %%Page: 1 1
D [10/Nov/2011:12:39:00 -0500] [Job 29] PAGE: 1 1
D [10/Nov/2011:12:39:00 -0500] [Job 29] Failed to connect to "smb://<username>:<password>@utlab-prsrv-02/": STATUS_LOGON_FAILURE
D [10/Nov/2011:12:39:00 -0500] [Job 29] ATTR: auth-info-required=username,password
D [10/Nov/2011:12:39:00 -0500] [Job 29] smb backend (PID=8517) stopped with status 512
D [10/Nov/2011:12:39:00 -0500] [Job 29] smb backend will exit with status 2
D [10/Nov/2011:12:39:00 -0500] [Job 29] Received SIGPIPE
D [10/Nov/2011:12:39:00 -0500] [Job 29] Wrote 1 pages...
D [10/Nov/2011:12:39:00 -0500] [Job 29] Backend returned status 2 (authentication required)
D [10/Nov/2011:12:39:00 -0500] [Job 29] Job held for authentication.
D [10/Nov/2011:12:39:00 -0500] [Job 29] End of messages
D [10/Nov/2011:12:39:00 -0500] [Job 29] printer-state=3(idle)
D [10/Nov/2011:12:39:00 -0500] [Job 29] printer-state-message="Authentication required"
D [10/Nov/2011:12:39:00 -0500] [Job 29] printer-state-reasons=none
=================
So yeah...
I'm totally stumped now.
I feel like I've tried every method imaginable, but still no luck.
Printing from OSX 10.6.8 works just FINE.
On the server side, I'm running Windows Server 2008... there's only a local admin and a local user account.
Clients running OSX Lion 10.7.2 -- All updated.
Printer is an HP LaserJet P4010-4510 series.
Workstation is an iMac 21.5-inch, Late 2009
3.06 Ghz Intel Core 2 Duo
Please help!!!
--- Richard

LPD print service is not enabled by default in Server 2008. It can be enabled via the Print Serveer role, but I am remote and cannot confirm the exact setting.
As for SMB, the error log is showing;
Failed to connect to "smb://<username>:<password>@utlab-prsrv-02/"
So it would suggest that there is still an issue with the account detail you are using as you show you have tried this syntax at one stage. If you want to continue to create the queue using SMB rather than LPD then I recommend using the CUPS web page (http://127.0.01:631) to create the queue. This will allow you to enter the syntax exactly as the error message shows. From previous testing I found it was okay to just use the account name rather than domain/account name on a domain bound server.

Issues on Installing Oracle on Windows Server 2008 Guested on VMware Workstation 10

I am trying to install Oracle 11g R2 on Windows Server 2008 Guested on VMware Workstation 10 but I am getting this Warning on Enterprise Manager Configuration at the end of installation.
Besides, when I tried to connect to hr database through Oracle SQL Developer I am getting following error:
Can you please let me know what I have done wrong? and how can I fix This? Thanks

Farzanx1 wrote:
I need to install and configure Active Directory and DNS service on a
remote Windows Server 2008 R2 which has a public facing IP, gateway
and DNS. I don't really understand such network structure:
IP Address: xx.xx.93.158
Subnet Mask: 255.255.255.252
Default Gateway: xx.xx.93.157
DNS: xx.xx.64.10
I have experience on installing AD and DC, DNS services on local
servers (which then the server becomes the DC for the local network)
but I hesitate to do this on a publicly facing production server.
Unfortunately I wasn't able to find a proper guide for my case.
Would appreciate if someone could guide me on the steps I need to
take so that I will not disturb the current network settings. (A
little down time for installing the services and features is ok as
long as I don't lose connectivity)
Thanks
You want to install AD on an Internet Server?
According to your description your server has one public IP-address and
no internal IP-address and you want to install AD on this Internet
server?? Is that correct??
Can you tell us the intended use of this server. Do you want to host
services on this server, which need AD authentication?
If you have a second NIC and your DC is on another local machine I
would not expose your local AD on an public accessible server. If this
server shall become a DC it should not have more than one IP-address.
If you want to access data on this server via Internet securely I would
recommend a VPN solution - preferably not running on the server itself
but on a separate firewall between the server and the internet. In this
case I would have no see a big security problem running AD on this
server.
Wolfgang

Windows Server 2008 R2: Unable to add a subnet to Site and Services

Similar Messages

Maybe you are looking for