Windows server for doucment storage

Is it possible to use windows server for repository of document? we are using unix server for sap system and wants to use windows server for storing documents and fetch the documets from windows serevr to unix server, Is it possible?

Hi,
You can install Content server on Windows server and then create a content repository on this Server.
Use this to store the DMS documents.
Regards
Abhishek

Similar Messages

VirtualDisk on Windows Server 2012 R2 Storage Pool stuck in "Warning: In Service" state and all file transfers to and from is awfully slow

Greetings,
I'm having some trouble with my Windows Storage Pool and my VirtualDisk running on a Windows Server 2012 R2 installation. It consists of 8x Western Digital RE-4 2TB drives + 2x Western Digital Black Edition 2TB drives and have been configured in a single-disk
parity setup and the virtual disk is running fixed provisioning (max size) and is formatted with ReFS.
It's been running solid for months besides some awful write-speeds at times, it seems like the write performance running ReFS compared to NTFS is not that good.
I was recommended to add SSD's for journalling in order to boost write-performance. Sadly I seemed to screw up this part, you need to due this through PowerShell and it needs to be done before creating the virtualdisk. I managed to add my SSD to the Storage
Pool and then remove it.
This seem to have caused some awkward issues, I'm not quite sure of why as the virtualdisk is "fixed" so adding the SSD to the Storage Pool shouldn't really do anything, right? But after I did this my virtual disk have been stuck in "Warning:
In Service" and it seems to be stuck? It's been 4-5 days and it's still the same and the performance is currently horrible. Moving 40GB of data off the virtual disk took me about 20 hours or so. Launching files under 1mb of the virtual disk takes several
minutes etc.. It's pretty much useless.
The GUI is not providing any useful information about what's going on. What does "Warning: In Service" actually imply? How am I supposed to know how long this is supposed to take? Running Get-Virtualdisk in PowerShell does not provide any useful
information either. I did try to do a repair through the Server Manager GUI but it goes to about 21% within 2-3 hours but drops back down to 10%. I have had the repair running for days but it wont go past 21% without dropping back down again.
Running repair through PowerShell yields the same results, but if I detach the virtual disk and then try to repair through PowerShell (the GUI wont let me do repair on detached virtual disks) it will just run for a split second and then close.
After doing some "Googeling" I've seen people mentioning that the repair is not able to finish unless I have at least the same amount of free space in the Storage Pool as the largest drive in my Storage Pool is housing so I added a 4TB drive as
due to me running fixed provisioning I had used all the space in the pool but the repair is still not able to go past 21%.
As am running "fixed provisioning" I guess adding a extra drive to the pool doesn't do much difference as it's not available for the virtual disk? So I went ahead and deleted 3 TB of data on the virtual disk so now I've got about 4 TB free space
on the virtual disk so there should be plenty of room for Windows Server 2012 R2 to re-build the parity or whatever it's trying to do but it's still the same, the repair wont move past 21% and the virtual disk is still stuck in "Warning: In Service"
mode and the performance keeps being horrible so taking a backup will take forever at these speeds...
Am I missing something here? All the drives in the pool is working fine. I have verified using various bootable tools so why is this happening and what can I do to get the virtual disk running at full state again? Why doesn't the GUI prompt you with any
kind of usable information?
Best regards, Thomas Andre

Hi,
Please run chkdsk /f /r command on the virtual disk to have a try. In the meantime, run the following commands in PowerShell to share the output.
get-virtualdisk -friendlyname <name> | get-physicaldisk | fl
get-virtualdisk -friendlyname <name> |fl
Best Regards,
Mandy
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Subscriber Support, contact [email protected]

Ia there a good alternative to Microsoft windows server for enterprise?

Hi Guys, I work at a small (22 FTE's) public(not-for-profit) art galley. We are currently a mixed pc/mac office with various departments, all with different needs. Communications/Design are Mac. 2/3rds of the Curatorial is Mac, 1/3rd PC. Public Programs is mostly Mac with one PC. The accounting, giftshop, and Databases are all PC. The giftshop and accounting use ACCPAC. The collections (artwork collection that is) department uses FileMaker Pro backend, with a frontend called "Virtual Collections". We very much dislike Virtual Collections BTW. Our other database, which handles membership, and financial donation tracking, is @EASE. Because we are not-for-profit our overall budget for IT is relatively small, and the system is the way it is because of years of neglect, and stop-gap purchases. We use a Microsoft Server with Exchange. We are in the process of building a new gallery, and with it the ability to start fresh on a number of levels. One of which is our Server. Personally I'd like to see us move away from the Microsoft server ecosystem. It is cumbersome, requiring lots of IT support (which we contract out by the way, and costs us a tidy little sum yearly on top of MS Server licensing etc.) Our Management team is considering going to an all PC environment with the (I feel mistaken) attitude that "if all computers are the same flavour, the whole system will run more smoothly and thus be less expensive to manage". As on of the Mac users within this system, who knows a little about, but is no expert in, computers and networks in general, I'd like to be able to open a dialogue with management at this crucial juncture on alternatives to the system we now use. I had run across a website some time ago that outlined the "real cost of owning and operating Microsoft Servers" but can not seem to locate it anymore. It basically broke down all costs of running a Microsoft environment, and concluded that, over time, it is not very cost efficient, especially for small enterprise. Has anybody run across any really good server alternatives to Microsoft Exchange, and Microsoft Windows Server (I think ours is 2008)? We are a relatively small city, and the IT/Networking companies here all seem to push Microsoft as a be-all-end-all. I'm not so sure. I'd like to present viable alternatives with sound arguments to back them up. Can you guys help? Or, an you point me toward someone who can? Thanks guys, keep up the good work, Tmamer

Have you ever got this resolved?
I noticed your VIP and Public IP are not on the same subnet, i thought they had to be?
like both 10.x.x.x and subnet 255.0.0.0 or something like that?
Could this be your problem?
I am trying to setup a two node cluster Oracle Rac 10g on IBM Blade Center H with HS21 XM blades.
My problem is trying to setup HA and not have a single point of failure and in order to do this, it almost seems as if i need 4 network interfaces in the HS21 blade so i can team 2 together.
Did you guys purchase any addition expansion cards for these servers for that reason?
My understanding is that each HS21 have by default 2 nics, and they each go to one of the two internal cisco switches (within the entire bladecenter).
So if for instance we have one of the cisco switch die, like the one that has the public interface plugged into it, then we could not longer access the rac and that would be a single point of failure. So unless we can have 4 interfaces on the blade, and have them 2 teamed with each nic going to one of the cisco internal switches. So if any one cisco switch die's it just uses the other one.
Any thoughts, suggestions?

Windows server for home user

hi
i have windows 7 on my desktop and a home network included cellphones, laptops and TV. i want to manage my network with active directory. i'm going to install windows server on my PC and my questions is:
does the windows server at home is good?
of course i'm a .NET programmer and i think programming in windows server better than in windows 7, am i right?
regards

Hi,
Most of PC level computer not certificated by Windows, so it can’t supported by Microsoft. But personal experience is you can run the server system on it, you can try to install
the Server 2012r2 then install all the role in the Hyper-V guest vm, it will give you more flexible.
And consider there often have more heterogenous operating systems in the home device, you can consider setup the Windows System Center Configuration Manager it have the heterogenous
system manage ability.
The related information:
Download Microsoft Hyper-V Server 2012 R2
http://technet.microsoft.com/en-us/evalcenter/dn205299.aspx
Device Management with Microsoft System Center 2012 Configuration Manage
http://download.microsoft.com/download/6/C/2/6C21A56F-B225-4BBA-99F4-877E6285AD5A/ConfigMgr_DeviceManagement.pdf
Hope this helps.
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Apache or Windows server for HTTP streaming

Does is matter what HTTP server I use?
In the process of upgrading from FMS 3.0 on Windows using IIS 5 to FMS 4.0. Will dynamic HTTP Streaming work from a Windows server?

Hi,
Thanks for your interest in HDS.
HTTP Dynamic Streaming only works with Apache web server. The basic Apache web server is already bundled along with FMS from the 4.0 versions where the HTTP Dynamic streaming modules are loaded by default. Alternatively, any external apache installation also can be used, by copying the required module files and changing the configuration apache files to enable them..

Deploying Windows Server for a class Project

I have downloaded Windows Server 2008 with no difficulty, however when I go to install it I run into issues. It loads into either one of two locations, 'C' Drive, disc 0 which it says is not compatible, GTP format or Disc 4 on my external HD. It
will not load from this second location because it says program is not bootable from a USB port. Is there a work-a-round?
LEO

Hello,
please see
http://www.disk-partition.com/articles/selected-disk-is-gpt-partition-style.html
Best regards
Meinolf Weber
MVP, MCP, MCTS
Microsoft MVP - Directory Services
My Blog: http://blogs.msmvps.com/MWeber
Disclaimer: This posting is provided AS IS with no warranties or guarantees and confers no rights.
Twitter:

How do I set access to the same network share on a Windows server for multiple users on an iMac (school set-up) in Lion 10.7.3?

We've got them authenticating/binding with AD (after hours of troubleshooting to get working), and their Home drive on the Windows 2003 server loads in the dock, but they also want to be able to load the same network shares on the server e.g. "Students$" for every student that logs onto the iMac. I realise without Lion server we can't control it by group, but if we could at least set it up consistently for the students that would be a great start.
Thanks.

When you install you get the opportunity to install it for "All Users".
It sounds like you have a demo version on your Mac however, you need to delete it:
http://www.freeforum101.com/iworktipsntrick/viewtopic.php?t=105&mforum=iworktips ntrick
Peter

Disk replication for Shared Storage in Weblogic server

Hi,
Why we need a disk replication in web-logic server for shared storage systems? What is the advantage of it and how this disk replication can be achieved in web-logic for the shared storage which contains the common configurations and software's which will be used by a pool of client machines? Please clarify.
Thanks.

Hi,
I am not the middleware expert. However ACFS (Oracle Cloud File System) is a clustering filesystem, which also has the functionality for replication:
http://www.oracle.com/technetwork/database/index-100339.html
Maybe you also finde information on what you need on the MAA website: www.oracle.com/goto/maa
Regards
Sebastian

Upload any file format to server for storage

hello,can anybody solve my doubt here in java . i wish to upload the file of any extension(any format) in to server for further storage in database.what will be the best server components and API used at the application logic leve?

Check out MultiPartRequest and MultiPartParser at O'Reilly's servlets site:
http://www.servlets.com/cos/index.html

Can I set 10 GB memory to NTFS read cache like CSV cache, or Stroage Space SSD Tier on Windows Server 2012 R2 ?

Can I set 10 GB memory to NTFS read cache like CSV cache, or Stroage Space SSD Tier on Windows Server 2012 R2 ?
I want to use 10 GB memory to NTFS file system read cache for random read speed up.
CSV Volume have CSV Cache function,
Windows Server 2012 R2 Storage Space have SSD Tier function.
Regards,
Yoshihiro Kawabata

Hi Yoshihiro,
There is no build-in system function which support to setup memory as disk cache. I know some third party software support this so you could have a search with related keywords (memory, hard disk cache).
If you have any feedback on our support, please send to [email protected]

After I reinstalled Windows Server 2012 R2, I cannot attach my virtual disk

Hello,
After I reinstalled Windows Server 2012 R2, I cannot attach manually my virtual disk "MOVIES" :
http://windowsitpro.com/systems-management/q-after-i-reinstalled-windows-server-2012-my-storage-spaces-are-no-longer-writabl
When i try this command : (http://technet.microsoft.com/fr-fr/Library/hh848641.aspx)
PS C:\>Connect-VirtualDisk –FriendlyName "MOVIES"I'have this error :PS C:\Windows\system32> Connect-VirtualDisk -FriendlyName "MOVIES"
Connect-VirtualDisk : Failed
Au caractère Ligne:1 : 1
+ Connect-VirtualDisk -FriendlyName "MOVIES"
+ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
    + CategoryInfo          : NotSpecified: (StorageWMI:ROOT/Microsoft/...SFT_VirtualDisk) [Connect-VirtualDisk], CimE
   xception
    + FullyQualifiedErrorId : StorageWMI 4,Connect-VirtualDiskI have the same problem with right clic attach on the manage interfaceAll my disks are OKI d'ont understand why i have a problemCould' you help me Tanks in advance for your helpRegards,Nicolas

Hello Elton,
I tried
numerous powershell
command to do anything
but I'm
lack of ideas.
All my disk are OK :
but
how can I do to make a
CheckDisk on a virtual disk because
there is no letter corresponding to the volume
It's only when i try to connect VirtualDisk to my Server
the problem happens ...
I try to repair the virtualDisk with powershell command :
PS C:\Windows\system32> Repair-VirtualDisk -FriendlyName MOVIESIt's works but it takes less than 2 seconds ...There is no solution?
I lost all my data? Can i try to delete virtual disk and recovery data with a recovery program,
is
that it might work?
Thanks you in advance for your help
Regards,
Nicolas

Install Windows server 2012 using powershell

Hi Folks,
How to Install Windows server 2012 using powershell.
Thanks,

Hi,
According to your post, my understanding is that you want to install Windows server 2012 via PowerShell.
Per the previous thread, we could not install Windows server 2012 directly via PowerShell.
https://social.technet.microsoft.com/Forums/en-US/53f82989-4b9c-4197-9ff1-03e96c852eb7/how-to-install-windows-server-2012-directly-in-vhd-file-using-powershell?forum=winserver8setup
As this is the forum for SharePoint server on-premise, I’m not familiar with the Windows server, for this issue, I recommend you can post a new question in the forum for Windows server.
https://social.technet.microsoft.com/Forums/en-US/home?forum=winserver8setup
More experts will assist you, then you will get more information relation to Windows server.
Thank you for your understanding and support.
More reference:
http://vegibit.com/install-and-configure-windows-server-2012-with-windows-powershell/
Thanks & Regards,
Jason
Jason Guo
TechNet Community Support

How Configure background update on windows Server

Hi,
I read Admin guide from http://www.adobe.com/devnet/flashplayer/articles/flash_player_admin_guide.html page 17-19 for background update installation and configuration but Document ask to create directory structure in Linux style and i want to configure it on my windows server please advice me how i create directory structure on windows server for background updates.
Your kind response much appreciated.
Regards,
Ahmed

On the Server where you want to share \usr\sap\trans for the landscape( I assume Server1 or PC1 in your terms), login as windows domain admin ( or with admin rights) --> right click my computer --> Manage --> click on Local Users and Groups --> Double click on administrators --> and add users of SAPService<SID> of the other server ( your Server 2 or PC2) and clock pk Ok.
This should resolve the problem.
Concept is, giving other server to read and write access to shared drive of Transport directory. There can be no. of days do implement it depending on in House Windows Skills and Secuirty audits, but the above method works.
Thanks,
Krishna

Windows Server Disconnecting Mac SMB Shares Randomly

The basic plot is I have a Mac Server sharing out files on AFP and SMB. I'm mounting one of those files shares on a Windows 2008 R2 server. Randomly the volume disconnects from the Windows server for a short period, somewhere around 20-30 minutes, and then reconnects. This happens 1-2 times a week.
I'm authentacation to the file share with user account 'Newforma". I have this same user account authentacating for files on other servers as well. At times one server will drop the authentacation while there is no issue with the other server. See the link below for a screenshot.
screenshot: http://redlinetech.files.wordpress.com/2013/04/smb_disconnect_01.jpeg?w=960
The Specs on machines:
Mac Server (dcfiles)
     Xserve2,1
     10.6.6
     Open Directory Master
     Services running: Open Directory, AFP, and SMB
Windows Server (STUDIOSDC10)
     HP ProLiant DL380 G6
     Windows Server 2008 R2 Standard
     Service pack 1 x 64
     Services running: setup as a Newforma Project Center Server, 9th edition.
My Windows server authenticates to our AD server for login, then files are mounted with authentication from our OD server. This does not cause any problems on the other windows servers and it's the same process that my desktop users have. They authenticate to AD for login, and OD for files. We do not bind AD or OD in any way.
Randomly though when I log into my Windows Server (DC10), There is a red 'X' on my mounted file share. If I double click I get an error message that the network volume doesn't exist. Nothing in the Windows Server Logs that I can find that point to an issue.
I believe the issue is the smb service running on my Mac 10.6 server (dcfiles). I think this because when my files are disconnected from the windows sesrver, I can try to authentacate to the Mac server from my mac desktop with AFP and everything works fine. But If I try to connect to the same file share with smb it doesn't connect. No error messages about wrong passwords or such, it never presents me with a login window. Just says the volume doesn't exist.
When I check the smb logs on the Mac server, I find this repeating over and over, it's pretty standard and in there all the time, even when I"m not having issues.
studiosdc10 (192.168.10.21) connect to service dcfiles initially as user Newforma (uid=1033, gid=20) (pid 69112)
[2013/04/08 09:30:16, 1, pid=69112] /SourceCache/samba/samba-235.5/samba/source/smbd/service.c:close_cnum(1289)
studiosdc10 (192.168.10.21) closed connection to service dcfiles
[2013/04/08 09:30:21, 0, pid=69112] /SourceCache/samba/samba-235.5/samba/source/lib/opendirectory.c:get_opendirector y_authenticator(247)
failed to read DomainAdmin credentials, err=67 fd=172 errno=34
[2013/04/08 09:30:21, 1, pid=69112] /SourceCache/samba/samba-235.5/samba/source/smbd/service.c:make_connection_snum( 1092)
studiosdc10 (192.168.10.21) connect to service dcfiles initially as user Newforma (uid=1033, gid=20) (pid 69112)
My concern is the line that says "failed to read DomainAdmin credentials, err=67 fd=172 errno=34". Though nothing seems to be actually be wrong. I can still authentcate to dcfiles with user 'Newforma' from my Windows server. Just worried that might point to something bigger.
I also run across these errors that have me a little more worried:
[2013/04/08 09:03:14, 0, pid=69112] /SourceCache/samba/samba-235.5/samba/source/lib/opendirectory.c:get_opendirecto ry_authenticator(247)
failed to read DomainAdmin credentials, err=67 fd=137 errno=34
[2013/04/08 09:03:17, 0, pid=231] /SourceCache/samba/samba-235.5/samba/source/lib/util_sock.c:get_peer_addr(1224)
getpeername failed. Error was Invalid argument
[2013/04/08 09:03:17, 0, pid=72621] /SourceCache/samba/samba-235.5/samba/source/lib/util_sock.c:set_socket_options( 261)
Failed to set socket option SO_KEEPALIVE (Error Invalid argument)
[2013/04/08 09:03:17, 0, pid=72621] /SourceCache/samba/samba-235.5/samba/source/lib/util_sock.c:set_socket_options( 261)
Failed to set socket option TCP_NODELAY (Error Invalid argument)
[2013/04/08 09:03:17, 0, pid=72621] /SourceCache/samba/samba-235.5/samba/source/lib/util_sock.c:get_peer_addr(1224)
getpeername failed. Error was Invalid argument
[2013/04/08 09:03:17, 0, pid=72621] /SourceCache/samba/samba-235.5/samba/source/lib/util_sock.c:write_data(562)
write_data: write failure in writing to client 0.0.0.0. Error Broken pipe
[2013/04/08 09:03:17, 0, pid=72621] /SourceCache/samba/samba-235.5/samba/source/lib/util_sock.c:send_smb(761)
Error writing 4 bytes to client. -1. (Broken pipe)
[2013/04/08 09:03:17, 0, pid=72622] /SourceCache/samba/samba-235.5/samba/source/lib/opendirectory.c:get_opendirector y_authenticator(247)
failed to read DomainAdmin credentials, err=67 fd=19 errno=2
[2013/04/08 09:03:42, 0, pid=69112] /SourceCache/samba/samba-235.5/samba/source/lib/opendirectory.c:get_opendirector y_authenticator(247)
failed to read DomainAdmin credentials, err=67 fd=143 errno=34
[2013/04/08 09:05:20, 0, pid=71861] /SourceCache/samba/samba-235.5/samba/source/smbd/nttrans.c:call_nt_transact_ioct l(2537)
call_nt_transact_ioctl(0x1401c4): Currently not implemented.
What I've Already Tried:
     - Stopping and restarting the SMB service
     - Adding "smb ports = 139” to the smb.conf file on the Mac server
What I'm Considering Trying:
     - Deleting and recreating the the 'Newforma' user account from Workgroup Manager on the Mac server
     - Making the 'Newforma' user account an admin
     - Fearing I might have bigger authentacation issues, demoting my OD master to Stand Alone and re-pormoting to Master.
While I continue to research, document, and monitor the issue ..... any thoughts or ideas would be appreaciated.

The basic plot is I have a Mac Server sharing out files on AFP and SMB. I'm mounting one of those files shares on a Windows 2008 R2 server. Randomly the volume disconnects from the Windows server for a short period, somewhere around 20-30 minutes, and then reconnects. This happens 1-2 times a week.
I'm authentacation to the file share with user account 'Newforma". I have this same user account authentacating for files on other servers as well. At times one server will drop the authentacation while there is no issue with the other server. See the link below for a screenshot.
screenshot: http://redlinetech.files.wordpress.com/2013/04/smb_disconnect_01.jpeg?w=960
The Specs on machines:
Mac Server (dcfiles)
     Xserve2,1
     10.6.6
     Open Directory Master
     Services running: Open Directory, AFP, and SMB
Windows Server (STUDIOSDC10)
     HP ProLiant DL380 G6
     Windows Server 2008 R2 Standard
     Service pack 1 x 64
     Services running: setup as a Newforma Project Center Server, 9th edition.
My Windows server authenticates to our AD server for login, then files are mounted with authentication from our OD server. This does not cause any problems on the other windows servers and it's the same process that my desktop users have. They authenticate to AD for login, and OD for files. We do not bind AD or OD in any way.
Randomly though when I log into my Windows Server (DC10), There is a red 'X' on my mounted file share. If I double click I get an error message that the network volume doesn't exist. Nothing in the Windows Server Logs that I can find that point to an issue.
I believe the issue is the smb service running on my Mac 10.6 server (dcfiles). I think this because when my files are disconnected from the windows sesrver, I can try to authentacate to the Mac server from my mac desktop with AFP and everything works fine. But If I try to connect to the same file share with smb it doesn't connect. No error messages about wrong passwords or such, it never presents me with a login window. Just says the volume doesn't exist.
When I check the smb logs on the Mac server, I find this repeating over and over, it's pretty standard and in there all the time, even when I"m not having issues.
studiosdc10 (192.168.10.21) connect to service dcfiles initially as user Newforma (uid=1033, gid=20) (pid 69112)
[2013/04/08 09:30:16, 1, pid=69112] /SourceCache/samba/samba-235.5/samba/source/smbd/service.c:close_cnum(1289)
studiosdc10 (192.168.10.21) closed connection to service dcfiles
[2013/04/08 09:30:21, 0, pid=69112] /SourceCache/samba/samba-235.5/samba/source/lib/opendirectory.c:get_opendirector y_authenticator(247)
failed to read DomainAdmin credentials, err=67 fd=172 errno=34
[2013/04/08 09:30:21, 1, pid=69112] /SourceCache/samba/samba-235.5/samba/source/smbd/service.c:make_connection_snum( 1092)
studiosdc10 (192.168.10.21) connect to service dcfiles initially as user Newforma (uid=1033, gid=20) (pid 69112)
My concern is the line that says "failed to read DomainAdmin credentials, err=67 fd=172 errno=34". Though nothing seems to be actually be wrong. I can still authentcate to dcfiles with user 'Newforma' from my Windows server. Just worried that might point to something bigger.
I also run across these errors that have me a little more worried:
[2013/04/08 09:03:14, 0, pid=69112] /SourceCache/samba/samba-235.5/samba/source/lib/opendirectory.c:get_opendirecto ry_authenticator(247)
failed to read DomainAdmin credentials, err=67 fd=137 errno=34
[2013/04/08 09:03:17, 0, pid=231] /SourceCache/samba/samba-235.5/samba/source/lib/util_sock.c:get_peer_addr(1224)
getpeername failed. Error was Invalid argument
[2013/04/08 09:03:17, 0, pid=72621] /SourceCache/samba/samba-235.5/samba/source/lib/util_sock.c:set_socket_options( 261)
Failed to set socket option SO_KEEPALIVE (Error Invalid argument)
[2013/04/08 09:03:17, 0, pid=72621] /SourceCache/samba/samba-235.5/samba/source/lib/util_sock.c:set_socket_options( 261)
Failed to set socket option TCP_NODELAY (Error Invalid argument)
[2013/04/08 09:03:17, 0, pid=72621] /SourceCache/samba/samba-235.5/samba/source/lib/util_sock.c:get_peer_addr(1224)
getpeername failed. Error was Invalid argument
[2013/04/08 09:03:17, 0, pid=72621] /SourceCache/samba/samba-235.5/samba/source/lib/util_sock.c:write_data(562)
write_data: write failure in writing to client 0.0.0.0. Error Broken pipe
[2013/04/08 09:03:17, 0, pid=72621] /SourceCache/samba/samba-235.5/samba/source/lib/util_sock.c:send_smb(761)
Error writing 4 bytes to client. -1. (Broken pipe)
[2013/04/08 09:03:17, 0, pid=72622] /SourceCache/samba/samba-235.5/samba/source/lib/opendirectory.c:get_opendirector y_authenticator(247)
failed to read DomainAdmin credentials, err=67 fd=19 errno=2
[2013/04/08 09:03:42, 0, pid=69112] /SourceCache/samba/samba-235.5/samba/source/lib/opendirectory.c:get_opendirector y_authenticator(247)
failed to read DomainAdmin credentials, err=67 fd=143 errno=34
[2013/04/08 09:05:20, 0, pid=71861] /SourceCache/samba/samba-235.5/samba/source/smbd/nttrans.c:call_nt_transact_ioct l(2537)
call_nt_transact_ioctl(0x1401c4): Currently not implemented.
What I've Already Tried:
     - Stopping and restarting the SMB service
     - Adding "smb ports = 139” to the smb.conf file on the Mac server
What I'm Considering Trying:
     - Deleting and recreating the the 'Newforma' user account from Workgroup Manager on the Mac server
     - Making the 'Newforma' user account an admin
     - Fearing I might have bigger authentacation issues, demoting my OD master to Stand Alone and re-pormoting to Master.
While I continue to research, document, and monitor the issue ..... any thoughts or ideas would be appreaciated.

Precalculation server on virtual windows server

Hi Friends,
Is it possible to use virtual windows server for workbook precalculation. If possible how we can configure precalculation server in it?
Thanks & Regards
Prasanth

Friends,
Kindly answer to my question.
Regards
Prasanth

Windows server for doucment storage

Similar Messages

Maybe you are looking for