Windows Shares Not Showing Up In Finder (Master Browser Problem)

Hi, on leopard I had no problems with Windows shares showing up in finder. However, having upgraded to Snow Leopard, I've now lost that ability.
Before I had my Leopard computer set as the master browser. I did this by specifying domain master = yes and preferred master = yes in my smb.conf. However despite importing these settings into Snow Leopard's smb.conf, it is not acting as a master browser.
When I run the command "nmblookup -M -- -" which in Leopard returned my Mac as the master browser, now it says "failed to find name _MSBROWSE_#01".
I'm sure this is why the Windows PC is not showing up in finder, but I don't know why the smb-conf isn't taking effect in Snow Leopard, and setting it as the master browser?
Also, I can use Go -> Connect to access my Windows shares, and Mac shares show up in Vista okay.
Any help appreciated.

Problem fixed upon updating to 10.6.2.

Similar Messages

  • Windows partition not showing up in finder OR disk utility

    doesn't snow leopard have ntfs support out of the box? Well I have windows 7 x64 installed via bootcamp, yet the windows partition will not show up in finder. I checked in disk utility and there is my macintosh HD, and a greyed out partition named disk0s4. It's 120gb, same size as the windows partion, but it says that it is FAT, which I know is not right. I even went so far as to to reformat the whole drive and reinstall both windows 7 and os x, and I am 100% sure it is a NTFS drive, even though it still will not mount in osx and it still says it's FAT in disk utility. What is going on??

    Go to Finder > Preferences > General
    Make sure External disks is selected.
    Restart your Mac then connect the external drive.

  • Solution for Windows PCs not showing up in Finder

    Hello guys,
    after fiddling around with the networking between Windows and Leopard I just wanted to share my solution with you.
    In my home network, there are three computers: One Vista machine, one XP machine and my MacBook. I found out that the Windows PCs only did show up in my finder if the Vista computer was turned on AFTER the MacBook (the XP computer didn't matter). This is apparently has something to do with Vista becoming the "master browser" in the SMB network. So you just have to prevent that this happens.
    And here's what you can do about it:
    On the Vista computer, go to Start->Run and type 'regedit'. Then browse to 'HKEYLOCALMACHINE\SYSTEM\CurrentControlSet\Services\Browser\Parameters' and change the Value of 'MaintainServerList' from 'Auto' to 'No'. Then reboot the PC.
    Now it shouldn't matter which computer is turned on first or last.
    NOTE: It still can take up to 15 minutes until the Windows PC show up in Finder.

    Thanks for posting this solution. I have 2 PC's plus BootCamp and this did the trick.

  • Windows computer not showing up in finder

    Hi,
    at the office we have a network of 4 windows computers and one mac which I use. In the finder I can see only 3 of the 4 windows machines. I checked the settings for the Windows computer that isn't showing up and it seems to be the same as the other three. What am I missing?
    Thank you in advance

    Assuming that the missing machine is part of the same Workgroup/Domain:
    Open Terminal and enter "nmblookup -M workgroupname" (without the quotes, and replacing workgroupname with the name of your workgroup or domain.
    This will list the IP address of the machine that is the "master browser" of your network. If you are on a domain, the address should be that of your domain controller. There should only be one ip address listed.
    You can then get that machine to list the shares that it see on the network by entering:
    "smbclient -L ipaddressofmasterbrowser"
    You should be able to just press enter when it asks for a password.
    This will list available shares and servers.
    Regards,
    Rodney

  • Network shares not showing up in finder osx Lion

    The shares on my network are not showing after I tried this SMBup. I tried to follow this guide but things didn't turn up as I was expecting them to work.http://knowledgebase.hsti.com/re-installing-smb-on-mac-os-x-lion-10-7-x
    This is the official website where in the middle of the page there is a note stating that "SMBUp installs Samba, which in turn replaces Apple’s OS X’s native netbios and SMB services. This means that while connecting to servers from the Finder remains functional, the Finder won’t be able to “browse” network services and servers from the network won’t show up in the Finder’s sidebar. Be advised."http://eduo.info/apps/smbup
    So i uninstall the samba restart the machine and now my shares don't show in the left side pane of finder. How can I get them back. Is the netbios service disabled

    Open Terminal and issue the following command
    ps aux | grep netbios[d]
    if you get a line similar to this
    _netbios          45   0,0  0,0  2477156   2456   ??  SNs   9:14am   0:02.44 /usr/sbin/netbiosd
    then the daemon is running, otherwise issue the following command to start netbiosd permanently
    sudo launchctl load -w /System/Library/LaunchDaemons/com.apple.netbiosd.plist

  • Recent hardware change - Windows 7 not showing up in finder

    Hi all
    First of all heres a quick overview of my current set-up
    13" macbook pro with OSX 10.6.4 / windows 7 bootcamped
    Desktop with Windows 7 / Ubuntu 10.04 LTS dual boot
    Desktop with Windows 7
    Routed through AEBS with another TB external drive attached as NAS
    (i just like to play with different os')
    so here's the problem, I have 4 hard drives in my windows 7/ubuntu box all of which are shared (its my server and i dont know enough about raid drives to sort that out without losing all my datas)
    I have these drives shared in ubuntu as well as windows 7 and can access everything fine from the other windows 7 box when the server is in either win 7 or ubuntu (ie drives C,D,E & F are all accessible with no problems)
    When the server is in ubuntu the mac can connect to all drives no problems
    when the mac is in Win7 I can connect to all drives on the server no problems
    when the server is in win 7 the mac wont connect to drives C and E fine as well as other folders such as the public ones
    HOWEVER the mac will not connect to drives D and F (these are not system files on either drive)
    but its all ok cus i just figured it out .... **** permissions on win 7 side... just weird that osx was the only system to throw up the issues
    SSSoooo for anyone having issues with accessing shares on your windows 7 pc (i have an open network in my house so not really good if its a share house type place)
    Add the guest account in the security section of your windows drives properties as well as your sharing section (or for that matter any account you see fit if your more security conscious)
    which after figuring that out i might just do hehe
    Ben

    Problem fixed upon updating to 10.6.2.

  • Network shares not showing up in finder

    This one has me stumped. I have a 3 computer set up, macbook 10.5.8, imac 10.6.6 and a macbook pro 10.5.8. From both the macbook and iMac I am able to see all other machines on the network and connect with no problem. On the pro I cannot see any of the other machines on the network. I can connect to them using command K and typing in that information, but under shared in the finder it doesn't list anything. I've poured through everything I can think of and every machine is identical in setup. Same workgroup, same firewall setup, same share set up, same everything. Can't figure this one out. I've also had issues with the pro disappearing from the other machine's shared section after time has gone by with no activity. The pro is not in a sleep state at these times and even if I go back to the machine and get it fully running again the connection is lost until I do a restart. FYI all of the machines are in the same vicinity and connecting to the same router so I don't think connectivity is an issue. I don't know if it's related because I haven't had this problem in about 2 weeks and I think I figured it out but the pro was having connection problems a few weeks ago every so often. When I would turn it on it would self assign an ip address. I tracked that problem down to a router security issue and believe I have fixed it but thought I would include that information. Before I figured out how to fix the problem a short term fix was to take the file from Library/Preferences/System Configuration and trash it and then do a restart. The system would rebuild the file and the issue would be taken care of temporarily. Don't think this has anything to do with my current problem either but thought I would include it just in case. What did I miss?

    Open Terminal and issue the following command
    ps aux | grep netbios[d]
    if you get a line similar to this
    _netbios          45   0,0  0,0  2477156   2456   ??  SNs   9:14am   0:02.44 /usr/sbin/netbiosd
    then the daemon is running, otherwise issue the following command to start netbiosd permanently
    sudo launchctl load -w /System/Library/LaunchDaemons/com.apple.netbiosd.plist

  • Windows Vista Computer not showing up in finder

    Hi, my WIndows Vista computer is not showing up in finder under Shared. I can connect to my PC from my mac by clicking on finder, go, connect to server and typing in the PC's IP Address, Username and Password. I can also see my Mac computer from my PC running Windows Vista.
    What's weird is that it was showing up for awhile but I recently changed my network key and unchecked file sharing on both my Mac and PC.
    Afterwards I re-enabled file sharing on both my mac and Vista computer but my PC won't show up in finder.
    I can connect to my PC and see the computer in finder but when I click eject, it disappears. I would like it to remain in finder. Is there some setting that I need to enable? Please help

    Assuming that the missing machine is part of the same Workgroup/Domain:
    Open Terminal and enter "nmblookup -M workgroupname" (without the quotes, and replacing workgroupname with the name of your workgroup or domain.
    This will list the IP address of the machine that is the "master browser" of your network. If you are on a domain, the address should be that of your domain controller. There should only be one ip address listed.
    You can then get that machine to list the shares that it see on the network by entering:
    "smbclient -L ipaddressofmasterbrowser"
    You should be able to just press enter when it asks for a password.
    This will list available shares and servers.
    Regards,
    Rodney

  • Shared devices not showing up in finder

    Shared devices on my network are not showing up in Finder on my MacBook Air. Problem just began in the last 24 hours, and is limited to just this computer. Have done usual things -- checking, unchecking shared devices in Finder; relaunching Finder; restarting computer. Any ideas?

    Your problem is very common under Snow. At first my shares did not show up under shared in finder windows. I, then, of course, used "Connect to Server" to connect to the shares--both Mac and PC. I found that the more I kept the shares active the more likely they were show up under shared. Then, I discovered that if I kept the computers from sleeping during the period of needed access they would tend to stay in shared without nearly so much keeping the connections active.
    If you do not like the above work around, then there are two other possibilities. You can elect to show mounted items on your desktop. Do that and connect to each share. Then, go > users > unlock > + login options > try dragging the mounted shares to the login item window. If successful, then the shares should be available at login.
    Another approach is to mount and connect as indicated above. Then, making an alias to the share should at least make things faster.

  • Want to upgrade to lastest version - help/about Firefox window does not show "upgrade" as in instructions.

    I want to upgrade to latest version but -Help/About Firefox- window does not show "upgrade" as in the instructions. I cannot find an "upgrade" function anywhere else. How do I upgrade? The version I have is -18.0.1- it came with this used computer.
    I believe this computer was hacked. Word started doing very strange things. We wiped the hard drive and reloaded everything as it was originally when I bought it. I am now getting hacked online.
    They originally got into one of my credit cards last fall. That is when this all started. They got my AOL email address. They also got the credit card current balance, minimum payment, due date and then even the payment amount. They got into my Barnes & Noble account and now checkout does not work. Now I believe they have gotten into my AOL account - one thing after another has started going wrong. I cannot change that AOL user id/email address since it is the master and I would lose about 15 years of "stuff".
    The folks that sold me this computer told me to use a free version of an antivirus. I am very unhappy with it. I never had ANY trouble when I used TrendMicro's expense products. Those folks also told me to use Firefox, since AOL uses Internet Explorer - which I already knew is like Swiss cheese.
    Now, I cannot seem to get an upgrade of Firefox. Is this also a hack?
    Please help any way you can. Thank you for your time.

    It's probably just the Firefox updater having some problems. go to www.getfirefox.com and download Firefox 20.0.1

  • A USB thumb drive with data created in Windows is not showing up on my desktop. Do I need a different driver or something?

    A USB thumb drive with data created in Windows is not showing up on my desktop. Do I need a different driver or something?

    OK in order to read those files you will need MS Office for Mac or install MS Windows on your Mac. You can get MS Office for Mac from anyone that sells Apple products. I would suggest the Apple Store, Best Buy, Amazon etc...For help getting the data from the memory stick I'd recommend visiting your local Apple Store or AASP and they can help you move it. It should be as simple as plugging the USB drive into your USB port and then open a Finder Window where you will see the drive on the left  pane. If you don't know what Finder is or how to open a new Finder window you need the sites I've noted below!!!
    Because you are new to OS X I would strongly recommend you bookmark and frequently visit the following web sites:
    Switch 101
    Mac 101
    Find Out How Video tutorials

  • TS3376 My phone is not showing up on find my iPhone.

    We've added another phone on to our iCloud and now our new phone is not showing up on find my iphone even though everything is turned on in the settings. 

    That article above, the one that has you disable the function, is to stop the little window from popping up whenever you connect a camera or iPhone with pictures.
    Try taking a look at this Apple doc -> iOS: Unable to import photos to computer

  • Updated and now tool windows are not showing up.

    I just updated my Muse and the pop open tool windows are not showing up. For example when I click on some text and then click on the list of typfaces the typeface window shutters and won't show up. This window keeps blinking from gray to black. I have uninstalled and re-installed the program. Also the tool window on the left side also cuts off the all of the tools. Also on my planning mode the A-master isn't showing up and I can't scroll to get to the A-master.

    The A-master not showing up at the bottom of the screen sounds like you must be running on a Windows machine with your screen resolution set to 125%. Try setting your resolution back to 100% (or if need be increase to 150%) and see if that helps.
    We don't support UI scaling in this release, but at the 125% setting Windows tries to scale us anyway and the result is not usable. We're working on a fix to avoid being scaled in this case.
    If it still behaves badly at 100%, would it be possible to post a screenshot?

  • Site Window does not show any item

    Hi,
    My site window does not show any items/folders to modify after I open my site.  I was wondering if there is anyone who can point out what I did wrong.  Usually the site window shows all the contents as soon as the site is opened.  Please help.  Thank you.
    coskinas

    If you look inside the webcontent folder, in Finder view (or Explorer???? if you're using Windows) - anyway, are there in fact files in there?
    Try Site > Update > Refresh all.
    If that doesn't work, try making a new site from existing content, which should give you a new site file (call it something slightly different) sitting beside your old one. I'm guessing here, but it can't hurt.

  • External Hard Drive does not show up in Finder

    My external hard drive is not showing up in Finder.
    It shows up in Disc Utility, but I do not have access to it. I have tried the following:
    command-shift c, nothing happens
    confirmed in Preferences/General that external hard drive was checked
    tried another cable
    tried another port on the back of the external drive
    tried to connect through the USB port
    re-started, etc.

    zone-5 wrote:
    I have same problem after installing OS 10.5.8. Disk utility sees the hard drive, the computer does not. Disk utility says invalid node structure. Volume check failed. Filesystem verify or repair failed.
    That means the directory is corrupt. If you have a heavy-duty 3rd-party disk repair app, such as +Disk Warrior,+ it may be able to fix it. Otherwise, your only option is to erase and reformat the disk. They're not cheap -- Disk Warrior is about $100. And for Leopard, you need version 4.1.1 or 4.2.
    I have not been able to figure out how to start a new topic here, but did find this discussion, which fits me fairly close.
    Just above the list of topics, on the left, is a +Post New Topic+ option.

Maybe you are looking for

  • EHP installing. Error in phase MAIN_SHDRUN/JOB_MSSSPEXE_SHD

    Hello all, Dealing with ECC's EHP4 installation and having problem with step JOB_MSSSPEXE_SHD. Firstly, want to give some system overview. System was migrated from x32 non-Unicode to x64 Unicode through SystemCopy OS: Windows Server 2008 SP2 DB: MS S

  • How to use the UME api in order to search the LDAP?

    Hello, I have an application which connects to the LDAP the portal is connecting to and search users according to a certain search criteria. Here is the relevant piece of code: Hashtable env = new Hashtable(); DirContext ctx = new InitialDirContext(e

  • New Hire Data Transfer from E-Rec to ECC via PA48

    Hi, We have requirement where we need to use the basic new hire data transfer from erec to ecc using PA48. Could someone help me by listing the step by step process that is required to configure in both EREC & ECC? I know there is pdf document availa

  • How to execute My Javascript code from command line or through perl or VB

    Hi Forum, I am a new bie, just 2 days old to acrobat and javascript, and I am basically a perl developer Here with I have created a small script to merge two pdf // Create a new PDF document: var newDoc = app.newDoc(); // Insert doc1.pdf: newDoc.inse

  • Replace downpayment from SD reporting with GL Indicator

    We have created a query for Billing report for SD(Gross Margin). We have excluded the downpayment hoping it will exclude. Downpayments are not revenue. My question is how we can bring in GL indicator and eliminate all records that have an entry of 'F