Windows Vista start-up problem

Please help!!! I have hp pavilion p6152f with vista 64-bit. I used windows 7 upgrade program to upgrade to windows 7. After several OS freezing i decided to recover to Vista using hard drive partition. So i did it but vista never started. I am unable to run it. I haven't any access to safe mode. It redirects me to startup repair but it is unable to repair computer automatically ant it give me that:
Problem Event Name: StartupRepairV2
Problem Signature 01: AutoFailover
Problem Signature 02: 6.0.6001.18000.6.0.6001.18000
Problem Signature 03: 5
Problem Signature 04: 196611
Problem Signature 05: CorruptRegistry
Problem Signature 06: CorruptRegistry
Problem Signature 07: 2
Problem Signature 08: 3
Problem Signature 09: RollbackRegistry
Problem Signature 10: 0
OS Version: 6.0.6001.2.1.0.256.1
locale ID: 1033
so please help

Hi,
This process will allow you to make a Vista Repair Disc. This is not an installation disc but will allow you to use the Vista Recovery Console that is available on retail versions of Vista.
Download the file on the link below.
Vista 64 bit
This is a zipped file. If you don't have an extraction utility installed, download and install 7-Zip which can be used to open this file. Simply right click the zipped file, select 7-Zip, select Extract Files and then click Ok. You should now see another folder containing the ISO file.
You will need software to burn the ISO to a CD. If you don't have this type on software installed, download and install ImgBurn and use this to burn the ISO to a CD.
Once you have created the Vista Repair Disc, follow the guide on the link below to see if this will repair your installation. If the initial startup repair doesn't work, try running windows System Restore from the Advanced Options as this may correct the registry corruption.
http://www.bleepingcomputer.com/tutorials/tutorial148.html#
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

Similar Messages

Trying to connect my replacement Iphone 3GS to my windows 7 laptop but it is not recognised at all, my ipod can connect no problem, my iphone can connect to my windows vista computer no problem. Any ideas?

Trying to connect my replacement Iphone 3GS to my windows 7 laptop but it is not recognised at all, my ipod can connect no problem, my iphone can connect to my windows vista computer no problem. Any ideas?

More info,
I have bootcamp with Windows 7 installed, do I need to run some "Driver compatibility checker" after the Windows 7install?
if so what is the name of it?
thanks

Desktop Software for my BB8320 using Windows Vista Starter OS

Can anyone help me on what desktop software to download for my BB8320 using a Windows Vista Starter OS?
Please help me>>>>
Thanks

I would recommend Desktop Manager version 4.7
Download Desktop Manager from here:
https://www.blackberry.com/Downloads/entry.do?code=A8BAA56554F96369AB93E4F3BB068C22
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Windows Vista Audio Driver Problem

My Windows Vista Drivers that I got for my MacBook Pro from the installation disk have bad audio drivers. The sound on the speakers is too low, and the microphone won't even work. When I talk into the microphone while under Sound Properties in the Recording tab, it shows that the microphone is picking up sound. However, in Ventrilo, and Windows Sound Recorder, there is no sound from my microphone.
I'm using Bootcamp 2.1. When will this problem be fixed? Will Apple release a new bootcamp version to fix this problem?? This is very important to me.
If anyone has fixed this problem, please tell me how you did it.
BTW, the audio device is called "Cirrus Logic CS4206A (AB75)"

Welcome. Make yourself at home.
http://discussions.apple.com/thread.jspa?threadID=2037093&tstart=30

Saound blaster audigy value windows vista 32 bit problem in driver compatibility!!!

i have installed the sb audigy value latest drivers july 9 2007?and it installed clean and then after a few restart it will detect again the standard?pci to pci bridge and sound devices... when i am using?xp this does not happenwhat is wrong with your drivers? i am installing the?drivers?again and again and same thing happen and my settings reverting always to 6 bit 48khz my card is 24 bit 96khz in the first install... and after a few restart?the setting for 24 bit and 96khz?will dissapear and the only available is 6 bit 48khz somtimes not working? kindly help me... plz... all my problem in windows vista 32 bit has been resolve this is the only one remaining...

Graphic drivers for the iMac is a regular question, and there are some tips and answers. I'd have skipped Vista, too much like beta and gone for 7, but you have it now....
Check the end of this thread with tips:
http://discussions.apple.com/thread.jspa?threadID=1866970&tstart=0&messageID=112 87449#11287449
And take a look for other similar threads.

Installing windows vista load driver problem

I am trying to load Windows Vista Ultimate SP1 32. I follow the bootcamp assistant instructions. I select "Disk 0 Partition 3 BOOTCAMP" as instructed but the "Next" button will not function. I can tab or select between drives, Refresh and Load Driver but cannot get to Next. The Bootcamp instructions say to load drivers after Windows is installed but I can't get Windows installed?? What am I doing wrong?
Thanks,
Bill

Found my own problem. Had to click on drive options advanced and format. That still didn't work because the disk was too small. Increased disk size and successfully completed install.

8520 Windows Vista Contact Sync problem

I recently added all my contacts from windows vista contacts and for some reason it assigned picutres to people who had no picture assigned from other pictures of people in my contacts, any suggestions.
Is there a way to do a mass removal of all contacts on device?
Thanks!

I have the same problem, when I sync the contacts they pass well from outlook to my iphone, but not the way around, indeed it changes my iphone contacts information and dismisses all the inputs that I already made in the iphone.

Upgrading to iTunes 9 on Windows Vista...PROBLEMS!

I recently upgraded to iTunes 9 on my computer, and it is Windows Vista. The computer and iTunes was perfectly fine before, but now iTunes doesn't come up when I open it and my iPod does not show up under "My Computer". I went to apple.com and reinstalled iTunes 9, hitting the "Repair" option when a choice came up, and iTunes popped up and it came up fine but I couldnt click on anything in the iTunes window because the computer became suddenly slow. After quitting out of the iTunes program using Task Manager, iTunes wouldnt come up again. I need help on what to do to have iTunes work again properly without losing the music already on my library. Thank you.

Yes
http://www.apple.com/itunes/download/

Windows Vista Bootcamp Driver Problems

Hello,
I have installed Windows Vista 32bit through Bootcamp, and the installation went through fine. I inserted my iMac "Mac OS X Install DVD" that came with my imac i bought in august. I tryed to run the program, but it said it was only availible for Windows 7. I could not acsess the internet through Wifi on Windows.
Could anyone give me instructions on how i can get the Windows Vista Drivers without the disk? the drivers, that bootcamp prompts me to install onto a usb, are also for windows 7 only. (ive already tryed this)
Thanks!

The hatter,
While running Vista, I navigate to Bootcamp setup.exe (my 10.6.6 disc is in the drive), it quits mid-launch and tells me Windows 7 is required. But Bootcamp user's manual says Vista is ok.
I'm using an 21.5" iMac with 10.6.8. I installed Windows Vista Home Basic 32 bit via bootcamp assistant. Vista is running fine but i can't surf the net. Error msgs say "network adaptor not found." Other forums lead me to believe it is a matter of bootcamp installing the proper drivers so vista can recognize my network hardware. But I can't even run bootcamp in Vista from my snow leopard CD b/c it quits and requires Windows 7.
My firmware is up to date as I checked it manually. According to my boot rom version, I need firmware update 1.9. After downloading and launching, msg tells me it is not compatible with my system. Please advise.

ThinkPad T60 8741-4SU + windows vista 64bit // temperature problems

ThinkPad T60 8741-4SU - High temperatures
Hi i recently upgraded my pc, bought set of 4gb ram (2x2gb of kingston ram), at that time i was running on windows xp prof sp2 and everything was fine, temperature was ok, idle at ~45C, burn ~70C.. Since i changed my os to windows vista ultimate 64 bit, temperatures are extremely high, idle is around ~60C and if i try to run some stability test that uses both cores at 100%, the temperature gets to ~95C and then i rather quickly stop it, because i dont want it to raise more and do some serious damage..
I dont have any lenovo software installed, i rather use the default stuff in windows - seems more user friendly so far.. So far i downloaded tpfancontrol to see if the fan is working properly and it seems it is, if i manually set it to max RPM, i can hear it, but the temperature is still about the same..
The other thing i am worried about it is that my intel t7400 is supposed to have max voltage at 1.3V, but i often see in Everest monitoring software, 1.36, CPUID shows 1.363, which is more than is supposed to be there, i was trying to see, if something is messed up in BIOS, but there is nothing about voltage - nothing that i can found..
My bios version is 1.03, windows vista ultimate 64bit - fully updated, outside temperature - the same, maybe even lower, laptop is sitting on the wodden desk.. Power setting at windows is set to Balanced, if i set the power saver- system is slow and with high performance the temperatures are running very high in the iddle.. I have the laptop for like 8months..
Other temperatures - idle
1 cpu 58°C (0x78)
2 aps 46°C (0x79)
3 crd 42°C (0x7a)
4 gpu 61°C (0x7b)
5 no5 50°C (0x7c)
7 bat 36°C (0x7e)
9 bus 44°C (0xc0)
10 pci 54°C (0xc1)
11 pwr 54°C (0xc2)
I think i havent forgotten anything, please and thanks for help and helpfull comments!
Thanks
Message Edited by whiller on 06-09-2008 01:13 AM

make sure your ventilation ducts are clean from dirt, Vista put lot more strain on every component of your laptop, so the temperature increase should be normal. Xp is lot less demanding on computer compoents, however it does sound like your heat ventilation fan and fins are clogged with dusts. So open up the laptop to clean away any dusts that maybe there.

ISO: solution for these itunes vs windows vista home premium problems?

1.Every time I start itunes, it tells me that there are registry entries missing for burning a disk and something else that escapes my immediate memory. However, it suggests reinstalling itunes and I've done that many times without the problem going away.
2. I use a sony laptop with vista and the latest itunes. The itunes task bar is not showing up.
3. When I go to those apple.com/itunes ads for free music, movie trailers, etc and then the itunes store redirector pops up, it always tells me that it can't find itunes, even when it is running.
4. Recently, itunes began to display the phrase "Disc Recording not found..."

Have you worked through the following document in the course of your troubleshooting to date?
[iTunes for Windows: "Registry settings" warning when opening iTunes|http://support.apple.com/kb/TS3299]

Idea Centre A600 Window 7 start up problem

I am using A600 all-in-one desktop.
Recently when i switch on my computer, after loading the lenovo screen, the machine automatically switch off by itself.
I don't know what is wrong about my computer
Is the programme in my computer causing the issue?

Try to start in safety mode, if it still doesn't start your pc could be faulty.
You can try to start from windows disc to fix os problems.

ASA 5510 and Windows Vista/7 VPN problems

Hi, I'm a programmer that's had to take over the sysadmin position (thank you economy) and our boss can't get access to the VPN with his new Windows 7 laptop. I've been banging my head trying to figure this out but I can't.
I think it gets past the phase 1 stuff, because windows stops the connection process when it hits "Authenticating username/password."
It works on our old XP systems and on OSX. It just doesn't seem to work on Windows 7.
Can anybody help? What do I have to add or change to get it to work?
Thanks so much in advance!
ciscoasa# sh run crypto
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA mode transport
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 mode transport
crypto ipsec ikev1 transform-set TRANS_ESP_AES128_SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_AES128_SHA mode transport
crypto ipsec ikev1 transform-set TRANS_ESP_AES256_SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_AES256_SHA mode transport
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 1 set ikev1 transform-set TRANS_ESP_AES128_SHA TRANS_ESP_AES256_SHA TRANS_ESP_3DES_SHA
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set TRANS_ESP_3DES_MD5 TRANS_ESP_AES128_SHA TRANS_ESP_AES256_SHA ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5
crypto map outside_map 1 match address outside_cryptomap
crypto map outside_map 1 set pfs group5
crypto map outside_map 1 set peer 11.22.33.44
crypto map outside_map 1 set ikev1 transform-set ESP-AES-192-SHA
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ikev1 enable outside
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 65535
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
ciscoasa# sh run tunnel-group
tunnel-group DefaultRAGroup general-attributes
address-pool l2tp_iprange
default-group-policy DefaultRAGroup
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group 11.22.33.44 type ipsec-l2l
tunnel-group 11.22.33.44 ipsec-attributes
ikev1 pre-shared-key *****

> What can we do?
Let your Cisco rep know that this is an important feature. The word I have is that stateful firewall is not in the Vista feature set for Cisco.
The readme for the Cisco VPN client 5.0 bears this out:
Known Issues:
CSCsh02887 Vista: Stateful firewall does not start.
CSCse44616 Vista: VPN Client should not install Zone Lab Firewall on Vista platform
CSCsf07334 Vista: Stateful Firewall Not Supported on Vista VPN Client

Windows 7 Starter share problems

I have a simple home network, has MYW7 (Starter), MYVISTA, MYXP and MYSAMBA(Linux) systems. No domain controller. I did the LmCompatibilityLevel registry hack to make Samba work.
Same user/pswd accounts on all systems.
MYW7 firewall is a 'Home' network.
MYVISTA, MYXP, MYSAMBA all can see each others shared disks, C, D, E(dvd), I've shared everything.
MYW7 can see drive C, D, E(DVD) on MYVISTA, C and D on MYXP, and all files on MYSAMBA. That works fine.
When I try to access anything from MYXP or MYVISTA to MYW7, I get a user/pswd request but there's nothing that I can type to satisfy it. When I type a valid user/pswd, it comes back with 'unable to log in' and suggests a user name of 'MYVISTA\mylogin' instead
of what I typed which was 'mylogin'.
I've turned on:
File and printer sharing
turn on sharing so anyone with network access can read and write files in the Public folders
Enable file sharing for devices that use 40- or 56-bit encryptino
password protected sharing
allow Windows to manage homegroup connections
I'd like to be able to see MYW7 files from MYXP and MYVISTA, and I'd like to be able to look at drive D from MYW7 to MYVISTA.
Also, when browsing the network using Windows Explorer, I often cannot see *some* systems, but I can get to them by doing a search for \\MYXP. This has been an ongoing problem. Is there some way I can cause the network browser to refresh the display and
find the missing nodes so it can display them in the tree of available nodes?
Thanks!

Please try the following steps in your Windows 7:
1. Launch regedit from Start Search box.
2. Find the following branch.
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Lsa
3. Create a DWORD key under Lsa and set:
Name: LmCompatibilityLevel
Value: 1
4. Restart.
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread. ”

PXE E53 error, and windows 7 start up problem error

recently, i have been getting an error called PXE E53 - no boot filename recieved. is the problem the hard drive? sometimes i get "windows 7 has failed to start. a recent hardware or software change might be the cause" and i choose start up repair, but then its just a black screen. any ideas of the problems im having?

Hi
This error comes if the OS or any boot device is not found in network boot, where the system tries to boot from Network or Boot Rom. Seems that teh BIOS setting is lost. To resolve teh issue. Enter BIOS by pressing F10 or F1 and reach the Boot tab (on the top with right arrow key). In the Boot tab there should be an option related to boot device priority, Select First Boot as HDD and then save settigs by pressing F10, select Yes for confirmation.
Now PC PC will reboot and hope the windows will boot.
Checkurtech
****Click the White Kudos star to say thanks****
****Please mark Accept As Solution if it solves your problem****

Windows Vista start-up problem

Similar Messages

Maybe you are looking for