WINS traffic not being forwarded

Hi folks,
For some reason, it seems that my WINS traffic isn't being forwarded across subnets over our 3750's. This is causing the workstations to have a "hit and miss" with authentication. I have enable "ip helper-address", "ip forward-protocol udp 137/138", even tried "ip directed-broadcast".
If I create create an LMHOST file, it works everytime. "Enable NetBIOS over TCP/IP" is enable on WinXP Clients. On Win98 clients receives it's setting from dhcp.
PCa---Vlan1 --<>-- Vlan2 ---- WINS Server / Authentication
Thanks..
-- Dominique

Hi Everyone,
This is how I have the device currently configured:
<..snip..>
ip dhcp excluded-address 10.203.8.1 10.203.8.29
ip dhcp pool 10.203.8.0/24
network 10.203.8.0 255.255.255.0
default-router 10.203.8.1
dns-server 10.70.0.9 10.70.0.6
domain-name rainbowschools.ca
netbios-name-server 10.203.0.7
netbios-node-type h-node
<..snip..>
!! Example Interface Configuration !!
interface FastEthernet1/0/23
description Academic
switchport access vlan 108
switchport mode access
no cdp enable
spanning-tree portfast
!! Server VLAN interface !!
interface Vlan100
ip address 10.203.0.1 255.255.255.0
!! Academic VLAN interface !!
interface Vlan108
ip address 10.203.8.1 255.255.255.0
ip helper-address 10.203.0.7
ip directed-broadcast
!! IP Forward Protocol !!
ip forward-protocol udp netbios-ss
ip forward-protocol udp bootps
ip forward-protocol udp bootpc
--> Even when I enter "ip forward-protocol udp 137/138", it doesn't appear. So I am assuming it is on by default.
Thanks.
-- Dominique

Similar Messages

VOIP calls not being forwarded from GW to GK and visa versa

I have a VOIP network setup in place using 2691 routers. i have a siemens PBX connected to the 2691 routers using an E1 controller (running QSIG), my WAN interface between the two sides is an ATM interface. when i do a csim start from one router to the extension on the other side the call goes through and the phone rings. However, when i actually dial from one extension to the other, the call is not being forwarded. and what happens is that i hear the dial tone again on the phone im dialing from.
I have taken some debugs but still could pin point the problem, even though in the ccapi inout debug i found that when it tries to look for a node, it doesnt find it.
I have attached the configuration for both sides. Along with the debug from one of the sites.
There are a couple of GW's associated with the GK.
The ones im concerned about are Mussalla_GW & GK-HO.
Thank You in advance
Mouhannad

Try this:
dial-peer voice 2 pots
direct-inward-dial
Without this command the router will not collect the digits coming across the PRI.
Please rate helpful posts.

Calls not being forwarded to skype number

Hello, I have had my Skype number for 2 years now and never had a problem.However since end of November 2012 calls from the USA are no longer being forwarded to my cellphone in Germany.No , I have not changed my settings , why should I , since it has been working perfectly all these years.There is no way to get help from Skype and I am extremely frustrated with their service.It sucks to pay for a product that won´t work.I am a dissatisfied customer and will leave them if they do not straighten out their stuff.

watsource wrote:
Hello, I have been a SKYPE user for the past 5 years and everything has been working fine. Recently, calls from telephones to my skype number are not being forwarded to my designated number. I've tried to turn off and on forwarding feature but still not working. Calls from other skype contacts using skype calling me are forwarded but not from any landline or mobile contacts calling my skype number.
What happens when you call your Online Number?
If calls directly from other Skype users are being forwarded to your designated number, but not the calls made to your Online Number, call-forwarding appears to be working. You may have a different issue related to your Online Number. Has it expired? If you click on "Account" at the top of this page, you can verify that your Online Number is still in effect by clicking on "Online Number" once you log into your Skype account through that link.
If your Online Number is still in effect, here's something else to check. From a computer (not the Skype app on a mobile phone or other device), can you verify the Privacy setting for Online Numbers? It should be set to allow calls from anywhere. If not, it is possible that this setting was changed, preventing you from getting calls on the Online Number.
Patrick
Location/Ubicacion: Arizona USA
Time Zone/Hora Local: UTC/GMT -7
If this message has adequately addressed your issue, please click on the “Accept as Solution” button. If you found a post useful then please "Give Kudos" at the bottom of my post, so that this information can benefit others.
Si esto mensaje le ha ayudado, por favor haga clic en "Aceptar como solución". Si encuentra un mensaje útil, por favor "Da Kudos" al final del mensaje, por lo que esta información puede beneficiar a otros.
I am not a Skype employee. No soy un empleado de Skype.

[svn:osmf:] 14982: Fixing some event parameters not being forwarded.

Revision: 14982
Revision: 14982
Author:   [email protected]
Date:     2010-03-24 02:15:50 -0700 (Wed, 24 Mar 2010)
Log Message:
Fixing some event parameters not being forwarded.
Modified Paths:
    osmf/trunk/apps/samples/framework/OSMFPlayer/src/DebuggerElementProxy.as

Hi,
Thanks for posting in Microsoft TechNet forums.
I will try to involve someone familiar with this topic to further look at this issue. There might be some time delay. Appreciate your patience.
Thank you for your understanding and support.
Kate Li
TechNet Community Support

WAAS VLAN - not all traffic is being forwarded to WAE

Hi, I've configured a WAAS topology based on this Cisco document
(http://www.cisco.com/application/pdf/en/us/guest/netsol/ns377/c649/ccmigration_09186a008081c7da.pdf)
where the WAE's are in their own VLAN and there is a trunk between the 2 edge routers and 2 6509 switches (the WAE's connect to this switch). Both the "data" vlan and the WAAS vlan is participating in EIGRP which means that traffic is being routed over both sub-interfaces. The problems is that one of the sub-interfaces has the "ip wccp redirect exclude in" command configured so only half the traffic will be passed to the WAE's. Has anyone come across this before? Should I be removing the WAAS vlan from EIGRP and using the second interface on the WAE for management in a seperate subnet?
interface GigabitEthernet0/0
description Trunk link to 6500
no ip address
interface GigabitEthernet0/0.901
description WAN Edge VLAN
encapsulation dot1Q 901 native
ip address 10.7.7.2 255.255.255.224
ip wccp 61 redirect in
ip wccp 62 redirect out
interface GigabitEthernet0/0.902
description WAAS VLAN
encapsulation dot1Q 902
ip address 10.7.9.1 255.255.255.240
ip wccp redirect exclude in
standby 1 ip 10.7.9.3
standby 1 timers 1 3
standby 1 priority 110
standby 1 preempt delay minimum 1
standby 2 ip 10.7.9.4
standby 2 timers 1 3
standby 2 priority 120
standby 2 preempt delay minimum 1
Edge_Router#sh ip ro 10.6.1.181
Routing entry for 10.6.1.0/21
Known via "eigrp 1", distance 90, metric 28928, type internal
Redistributing via eigrp 9
Last update from 10.7.7.1 on GigabitEthernet0/0.901, 08:18:01 ago
Routing Descriptor Blocks:
10.7.7.1, from 10.7.7.1, 08:18:01 ago, via GigabitEthernet0/0.902
Route metric is 28928, traffic share count is 1
Total delay is 130 microseconds, minimum bandwidth is 100000 Kbit
Reliability 245/255, minimum MTU 1500 bytes
Loading 12/255, Hops 3
* 10.7.9.1.2, from 10.7.9.1.2, 08:18:01 ago, via GigabitEthernet0/0.901
Route metric is 28928, traffic share count is 1
Total delay is 130 microseconds, minimum bandwidth is 100000 Kbit
Reliability 245/255, minimum MTU 1500 bytes
Loading 12/255, Hops 3

BRADLEY,
In this case you should make the data VLAN passive (from an EIGRP perspective) and use the WAE VLAN as a transit between the two routers. You don't want traffic coming in from the WAE VLAN to get re-intercepted.
Zach

Network Policy Server Event ID 6272 not being forwarded to Event Collector.

Hi there
I have configured an Event Subscription to collect events from 2 DCs that run RADIUS for network switches. It appears the events are being forwarded okay, I am getting the Security events (Logon and Logoff) on the event collector PC. However I am not getting
any of the Network Policy Server security events (specifically Event IDs 6272), to centrally audit RADIUS logins to switches.
The subscription is collector initiated, and I have added Network Service to the Event Log Readers Group. Is there something I am missing in the setup requirements for these events to be forwarded?
Thank you,
Kind regards
Hylton

Hi Gabriel101,
Could you offer us more information about your environment, such as what edition server you are using, whether your AD and NPS role on the same server, whether your NPS working
properly now, whether you can receive others security auditing.
The related KB:
NPS Local Log File Status
http://technet.microsoft.com/en-us/library/cc735386(v=ws.10).aspx
Event ID 6272 — NPS Authentication Status
http://technet.microsoft.com/en-us/library/cc735388(v=ws.10).aspx
I’m glad to be of help to you!
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Voip: CLI is not being forwarded

Dears,
I connected cisco 3800 router with ericsson MD110 exchange using QSIG over E1 Pri. Calls are forwarding properly over ip network but few features are not being enabled specially CLI feature. I found a documnet where a command "caller-id enable" was issue in voice-port interface. But i go in this mode using command voice-port 1/0:15, no command caller-id find. My topology is below:
MD110 PBX ----3845---------3825----MD110 PBX
Waiting for immediate positive response.
Regards
Rameez

R1#
Oct 30 13:19:12.465: ISDN Se1/0:15 Q931: RX <- SETUP pd = 8 callref = 0x3684
Bearer Capability i = 0x8090A3
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xA18381
Preferred, Channel 1
Progress Ind i = 0x8183 - Origination address is non-ISDN
Calling Party Number i = 0x0181, N/A
Plan:ISDN, Type:Unknown
Called Party Number i = 0x81, '3'
Plan:ISDN, Type:Unknown
Shift to Codeset 5
Codeset 5 IE 0x31 i = 0x80
Shift to Codeset 5
Codeset 5 IE 0x32 i = 0x81
R1#
Oct 30 13:19:12.469: ISDN Se1/0:15 Q931: TX -> SETUP_ACK pd = 8 callref = 0xB684
Channel ID i = 0xA98381
Exclusive, Channel 1
Oct 30 13:19:13.005: ISDN Se1/0:15 Q931: RX <- INFORMATION pd = 8 callref = 0x3684
Called Party Number i = 0x81, '0'
Plan:ISDN, Type:Unknown
R1#
Oct 30 13:19:13.481: ISDN Se1/0:15 Q931: RX <- INFORMATION pd = 8 callref = 0x3684
Called Party Number i = 0x81, '0'
Plan:ISDN, Type:Unknown
Oct 30 13:19:14.429: ISDN Se1/0:15 Q931: RX <- INFORMATION pd = 8 callref = 0x3684
Called Party Number i = 0x81, '1'
Plan:ISDN, Type:Unknown
R1#
Oct 30 13:19:14.577: ISDN Se1/0:15 Q931: TX -> CALL_PROC pd = 8 callref = 0xB684
Oct 30 13:19:14.693: ISDN Se1/0:15 Q931: TX -> ALERTING pd = 8 callref = 0xB684
Facility i = 0x9FAA068001018201018B0100A1080201020201018000
Progress Ind i = 0x8188 - In-band info or appropriate now available
Oct 30 13:19:14.737: ISDN Se1/0:15 Q931: RX <- FACILITY pd = 8 callref = 0x3684
Facility i = 0x9FAA06800100820100A406020102810102
R1#
Oct 30 13:19:20.841: ISDN Se1/0:15 Q931: TX -> CONNECT pd = 8 callref = 0xB684
Progress Ind i = 0x8182 - Destination address is non-ISDN
Connected Number i = 0x0181, '3001'
Shift to Codeset 5
Codeset 5 IE 0x32 i = 0x81
Oct 30 13:19:20.901: ISDN Se1/0:15 Q931: RX <- CONNECT_ACK pd = 8 callref = 0x3684
R1#
Oct 30 13:19:32.625: ISDN Se1/0:15 Q931: TX -> DISCONNECT pd = 8 callref = 0xB684
Cause i = 0x8190 - Normal call clearing
Oct 30 13:19:32.681: ISDN Se1/0:15 Q931: RX <- RELEASE pd = 8 callref = 0x3684
Cause i = 0x8190 - Normal call clearing
Oct 30 13:19:32.681: ISDN Se1/0:15 Q931: TX -> RELEASE_COMP pd = 8 callref = 0xB684
R1#u all
All possible debugging has been turned off
R1#
Output of Router R2 you will find in my next post as i have to split output due to character limit.
Regards

Port not being forwarded in WRT54GR

As Topic says, here are the screenshots in what I did, I even did DMZ but my ports are not forwarded.

1.
2.
Active Connections
Proto Local Address          Foreign Address        State
TCP    0.0.0.0:135            0.0.0.0:0              LISTENING
TCP    0.0.0.0:445            0.0.0.0:0              LISTENING
TCP    0.0.0.0:2869           0.0.0.0:0              LISTENING
TCP    0.0.0.0:5357           0.0.0.0:0              LISTENING
TCP    0.0.0.0:49152          0.0.0.0:0              LISTENING
TCP    0.0.0.0:49153          0.0.0.0:0              LISTENING
TCP    0.0.0.0:49154          0.0.0.0:0              LISTENING
TCP    0.0.0.0:49155          0.0.0.0:0              LISTENING
TCP    0.0.0.0:49156          0.0.0.0:0              LISTENING
TCP    0.0.0.0:49157          0.0.0.0:0              LISTENING
TCP    0.0.0.0:49893          0.0.0.0:0              LISTENING
TCP    127.0.0.1:49190        127.0.0.1:49191        ESTABLISHED
TCP    127.0.0.1:49191        127.0.0.1:49190        ESTABLISHED
TCP    127.0.0.1:49199        127.0.0.1:49200        ESTABLISHED
TCP    127.0.0.1:49200        127.0.0.1:49199        ESTABLISHED
TCP    192.168.1.110:139      0.0.0.0:0              LISTENING
TCP    192.168.1.110:49724    64.4.9.101:1863        ESTABLISHED
TCP    192.168.1.110:49733    64.4.9.97:1863         ESTABLISHED
TCP    192.168.1.110:49782    65.55.194.253:443      TIME_WAIT
TCP    192.168.1.110:49783    65.55.194.253:443      TIME_WAIT
TCP    192.168.1.110:49784    65.55.194.253:443      TIME_WAIT
TCP    192.168.1.110:49785    65.55.194.253:443      TIME_WAIT
TCP    192.168.1.110:49786    65.55.194.253:443      TIME_WAIT
TCP    192.168.1.110:49793    208.74.204.125:80      TIME_WAIT
TCP    192.168.1.110:49796    208.74.204.125:80      TIME_WAIT
TCP    192.168.1.110:49797    208.74.204.125:80      TIME_WAIT
TCP    192.168.1.110:49803    208.74.204.125:80      TIME_WAIT
TCP    192.168.1.110:49807    208.74.204.125:80      TIME_WAIT
TCP    192.168.1.110:49811    208.74.204.125:80      TIME_WAIT
TCP    192.168.1.110:49813    208.74.204.125:80      TIME_WAIT
TCP    192.168.1.110:49815    208.74.204.125:80      TIME_WAIT
TCP    192.168.1.110:49816    208.74.204.125:80      TIME_WAIT
TCP    192.168.1.110:49817    208.74.204.125:80      TIME_WAIT
TCP    192.168.1.110:49818    208.74.204.125:80      TIME_WAIT
TCP    192.168.1.110:49828    208.74.204.125:80      TIME_WAIT
TCP    192.168.1.110:49837    208.74.204.125:80      TIME_WAIT
TCP    192.168.1.110:49841    208.74.204.125:80      TIME_WAIT
TCP    192.168.1.110:49844    208.74.204.125:80      TIME_WAIT
TCP    192.168.1.110:49854    209.85.225.95:80       ESTABLISHED
TCP    192.168.1.110:49859    207.46.124.136:443     ESTABLISHED
TCP    192.168.1.110:49879    207.46.125.253:7001    TIME_WAIT
TCP    192.168.1.110:49883    154.20.137.56:55562    ESTABLISHED
TCP    192.168.1.110:49884    207.46.125.253:7001    TIME_WAIT
TCP    192.168.1.110:49885    65.55.194.253:443      TIME_WAIT
TCP    192.168.1.110:49886    65.55.194.253:443      TIME_WAIT
TCP    192.168.1.110:49887    65.55.194.253:443      TIME_WAIT
TCP    192.168.1.110:49889    65.55.194.253:443      ESTABLISHED
TCP    192.168.1.110:49890    65.55.194.253:443      ESTABLISHED
TCP    192.168.1.110:49891    207.46.113.93:443      ESTABLISHED
TCP    192.168.1.110:49892    207.46.125.253:7001    TIME_WAIT
TCP    [::]:135               [::]:0                 LISTENING
TCP    [::]:445               [::]:0                 LISTENING
TCP    [::]:2869              [::]:0                 LISTENING
TCP    [::]:5357              [::]:0                 LISTENING
TCP    [::]:49152             [::]:0                 LISTENING
TCP    [::]:49153             [::]:0                 LISTENING
TCP    [::]:49154             [::]:0                 LISTENING
TCP    [::]:49155             [::]:0                 LISTENING
TCP    [::]:49156             [::]:0                 LISTENING
TCP    [::]:49157             [::]:0                 LISTENING
TCP    [::]:49894             [::]:0                 LISTENING
UDP    0.0.0.0:123            *:*
UDP    0.0.0.0:500            *:*
UDP    0.0.0.0:623            *:*
UDP    0.0.0.0:664            *:*
UDP    0.0.0.0:3702           *:*
UDP    0.0.0.0:3702           *:*
UDP    0.0.0.0:4500           *:*
UDP    0.0.0.0:5355           *:*
UDP    0.0.0.0:60919          *:*
UDP    127.0.0.1:1900         *:*
UDP    127.0.0.1:50242        *:*
UDP    127.0.0.1:52704        *:*
UDP    127.0.0.1:60925        *:*
UDP    192.168.1.110:9        *:*
UDP    192.168.1.110:137      *:*
UDP    192.168.1.110:138      *:*
UDP    192.168.1.110:1900     *:*
UDP    192.168.1.110:7587     *:*
UDP    192.168.1.110:60924    *:*
UDP    [::]:123               *:*
UDP    [::]:500               *:*
UDP    [::]:3702              *:*
UDP    [::]:3702              *:*
UDP    [::]:5355              *:*
UDP    [::]:60920             *:*
UDP    [::1]:1900             *:*
UDP    [::1]:60922            *:*
UDP    [fe80::100:7f:fffe%11]:1900 *:*
UDP    [fe80::100:7f:fffe%11]:60923 *:*
UDP    [fe80::31e6:cdb:363c:5305%10]:1900 *:*
UDP    [fe80::31e6:cdb:363c:5305%10]:60921 *:*
Yeah I also have a voip connected, but I haven't tampered with the settings in that device yet, even though I DO have access to the settings, I don't really know how to tamper with it.
Thanks for the reply so far, got home late~

Emails Not Being Forwarded in a non-wireless environment...

This is very strange and I'm not sure if it's something I did or if there's something wrong with my phone..
I have my emails forwarded from my AOL account using TMobile's service. Up until now, I've not had any problems..
I also have my WiFi turned on in several locations which I frequent (my home, office and Starbucks). What is happening is my phone is not forwarding ANY of my emails, texts or PINs unless I'm in one of these WiFi locations. I've checked all of my connections and both my Mobile Network as well as my WiFi connections are both turned on.
I've tried resetting the phone many times, I've even recreated my email addresses in Blackberry Internet Service and still, NO EMAILS unless I'm within WiFi range..
Does anyone have any idea what's going on here? Did I accidentally switch something off or on that I shouldn't have that is blocking my email, texts & PINs?
Thanks in advance for your help.
Sophie
Message Edited by sophbakall on 01-04-2009 02:39 AM

You said you've reset your phone? Did you remove the battery and reboot it?
With the BlackBerry device powered ON, remove the battery a few seconds and then reinsert the battery to reboot.
Try also removing/deleting your Service Books for email accounts at Options > Advanced > Servcie Books, then readding them from your BIS account login.
Resend your service books from your carrier BIS site.
http://www.blackberryfaq.com/index.php/Where_can_I_log_into_my_BIS_account%3F
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4   Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA   Display/Scan Bar Code

Email from specific email not being forwarded to BB

Since I have set up my owa email account on the BB, using BIS, there are emails I am unable to receive from specific users on the BB. These users are within the same domain as me and the emails are in my inbox when I log in to my account through IE. I also use an IMAP account on the BB and those users are copying that email and those emails are forwarded to the BB via that email, but not my email via OWA. Has anyone had this issue before, does anyone have any kind of solution to this problem?
We have already deleted and readded the email on the BB and nothing is working....
Any insight would be helpful.
Thanks

Look through the Cookie extensions at AMO for an extension that has the features you want.
[https://addons.mozilla.org/en-US/firefox/search/?q=cookies&cat=all&lver=any&atype=0&sort=&pid=1&pp=20&lup=&advanced= AMO search for "cookies" extensions]

H323 cisco attributes not being forwarded to Radius accounting server

I have enabled a Radius server to gather AAA Accounting CDR records but I don't see any of the Cisco h323 attributes. The following is an example of the list I WANT to see.
ATTRIBUTE h323-remote-address 23 string Cisco
ATTRIBUTE h323-conf-id 24 string Cisco
ATTRIBUTE h323-setup-time 25 string Cisco
ATTRIBUTE h323-call-origin 26 string Cisco
ATTRIBUTE h323-call-type 27 string Cisco
ATTRIBUTE h323-connect-time 28 string Cisco
ATTRIBUTE h323-disconnect-time 29 string Cisco
ATTRIBUTE h323-disconnect-cause 30 string Cisco
ATTRIBUTE h323-voice-quality 31 string Cisco
ATTRIBUTE h323-gw-id 33 string Cisco
ATTRIBUTE h323-incoming-conf-id 35 string Cisco
I see a lot of stuff comming in, but I don't see any of the attributes above.
PS. when I do a DEBUG AAA ACCOUNTING here's what I see.
*Oct 8 18:00:19.681: AAA/ACCT/CONN(00001863): STOP protocol reply FAIL
*Oct 8 18:00:19.681: AAA/ACCT(00001863): Accouting method=NOT_SET
Here's my config
aaa new-model
aaa group server radius ACS
server X.X.X.X auth-port 1645 acct-port 1646
aaa authentication login h323 group ACS
aaa authentication login no_rad local
aaa accounting update newinfo
aaa accounting exec default start-stop group ACS
aaa accounting connection default start-stop group ACS
aaa accounting connection h323 start-stop group ACS
aaa session-id common
gw-accounting aaa
attribute acct-session-id overloaded
attribute h323-remote-id resolved
acct-template callhistory-detail
radius-server host X.X.X.X auth-port 1645 acct-port 1646
radius-server timeout 60
radius-server key XXXXX
radius-server authorization permit missing Service-Type
radius-server vsa send accounting
radius-server vsa send authentication
dial-peer voice 447 voip
destination-pattern 1647280....
voice-class aaa 1
session target ipv4:X.X.X.X
Any ideas?
thanks,
Paul

Try the following command:
gw-accounting h323 vsa
See here (http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122newft/122tcr/122tvr/vrg_g1.htm#wp1505752) for details.

Captivate 5: Acrobat Quiz Results Not being Forwarded - Screen Freezes.

After completing the quiz, then pressing the POST button, I fill in the required two fields; but, the screens freezes or remains on the ...signing in status indefinitely.
I tried all the security settings for my pc and the acrobat website with no success.
I tried various Captivate settings and still no solution.
Is there something else I could try, I need to temporaily use Captivates' Score Result feature until the LMS is online.
Thank You
iaustin

Hi,
Can you try repubklishing your course using Flash Playe 10 in settings of Publish options?
Can you add the location of your published output to Flash player, Global Security settings to Trusted Locations--
http://www.macromedia.com/support/documentation/en/flashplayer/help/settings_manager04.htm l
Thanks,
Anjaneai

Invite Email not being sent from iCal from a Google Apps calendar

Hello,
I am running Mac OS X 10.6.5, iCal 4.0.4, and am attempting to do the following from a Google Apps calendar I have setup in iCal. Please note that it's not gmail, it's Google Apps. If that makes a difference. That being said...
I am trying to create a meeting invite from iCal. I am able to create the invite and add attendees with no problem. When I hit send (from iCal), the invitees do not receive an email notification of the event, but it does appear their calendar (both in iCal and via Google Calendar on the web). I need an email to be sent to the invitees that they have been invited to a meeting, not just to have it appear on their calendars.
When I create the meeting invite via Google Calendar on the Web the invitees do receive an email notification (as specified in their calendar preferences). The issue only happens when the meeting invite is created in iCal.
When an invitee accepts or declines a meeting via iCal I receive an acceptance or declining email. Just not when the meeting invite is sent.
Also, I am able to create a meeting on one of the "On My Computer" calendars in iCal, invite people, and a meeting invitation is sent as expected.
And again, the invitees have notification of meeting invites turned on in their calendar settings (as is shown by the fact that when the invite is sent out via Google Calendar on the Web they receive an email with the invite).
Thanks! Any assistance would be awesome.
Aaron

That was actually my post on the Google forums
Here is what I have found so far (and hopefully some of my assumptions are correct, because we're making the full switch to Google Apps this weekend and I am assuming it will work after this). This is long, but I'm trying to be thorough. Also note that I have updated to 10.6.6 since the time I first posted my last message.
We are currently piloting Google Apps, so our primary domain (which I will refer to from now on as domain.com) still points to our old exchange servers. Mail is currently being delivered to our Google Apps pilot accounts the following way:
1. User sends an email to [email protected]. This email is delivered to our old Exchange servers.
2. Once the email is received on our old Exchange servers it gets forwarded to our Google Apps test domain (gtest.domain.com).
This seems to be an important piece of the puzzle as our primary domain (domain.com) shows up on the Google Apps for Admin dashboard as improperly setup (which is correct, because we're currently piloting)
So, in iCal I have my Google Apps account setup (I'm one of the pilot users) the following way. I added the Account as Google calendar in iCal, but once the account shows up it shows up as a CalDAV account.
Under the account information tab:
CalDAV
Description: [email protected]
User name: [email protected]
Password: my password
Under the server settings tab (*NOTE: these were entered in automatically when I setup the calendar as a Google calendar)
Server address: www.google.com
Server path: the path to my calendar.
Use SSL is checked
Use Kerberos v5 is NOT checked
So, during my testing I was sending meeting invites from people who were in the Google Apps pilot to other people who were in the Google Apps pilot. When I was doing that, no invitations were getting sent.
I created a new email account on our exchange server ([email protected]) but did NOT set it up to be a part of the Google Apps pilot (this means that emails were not being forwarded from [email protected] to [email protected]). Doing this successfully delivered all invites, cancellations, and meeting updates from iCal!
From what I can tell there must be something going on (probably my own fault) when a calendar invite is sent from my Google Apps account, through our old Exchange system, and then back to our Google Account. My assumption is it has something to do with the fact that our MX records for domain.com currently point to our old exchange servers, and the MX records for gtest.domain.com point to the Google Apps servers. It may also have something to do with the SPF record which only allows emails from domain.com to be sent from our Exchange servers.
Those are just guesses though as I am not very knowledgeable in that area.
I hope this helps and I would love to hear about anyone else working on this issue.

Text messages not being sent to computer

My text messages are not being forwarded to my computer anymore, and I can't text to non-iPhone users

Handoff Continuity Troubleshooting
Handoff Continuity Troubleshooting (2)
iPhone, iPad, iPod touch, and Mac using Continuity - Connect

Emails not being downloaded from BTYahoo to Outloo...

Since Thursday have had a problem with emails not being forwarded to my Outlook in box, this is about the third time this has happened. I did notice that some else has posted with the same problem. Any ideas on how to unblock the system! The only other solution is to get through to BT Help in India! Must admit they were very helpful last time this happened. Any solutions greatly appreciated, bearing in mind that I willl have to go to my BTYahoo page to see any solutions. Many thanks. caravanlady

caravanlady wrote:
Since Thursday have had a problem with emails not being forwarded to my Outlook in box, this is about the third time this has happened. I did notice that some else has posted with the same problem. Any ideas on how to unblock the system! The only other solution is to get through to BT Help in India! Must admit they were very helpful last time this happened. Any solutions greatly appreciated, bearing in mind that I willl have to go to my BTYahoo page to see any solutions. Many thanks. caravanlady
Hi.
It seems that more and more people are experiencing issues using Outlook, however the problem is more likely down to a couple of reasons.
If could be an Outlook account corruption - so creating a new account in Outlook with the same email details may work. Also logigng into webmail (BTYahoo!) and moving the latest Inbox emails into a temporary folder. Then move a few at a time and retry Outlook, in case there is a corrupt email which can be dealt with separately.
Do you keep all the emails on the server ? If so, there is a chance that this could cause issues with any mail client program such as Outlook - as they have to index the emails so that they don't download ones already seen.
http://www.andyweb.co.uk/shortcuts
http://www.andyweb.co.uk/pictures

WINS traffic not being forwarded

Similar Messages

Maybe you are looking for