WinSock error on connect

Hi
I have tried to login to data manager & Import Manager with out giving password for Admin.I am getting an error
********WinSock error on connect*********
Even i tried to connect by giving $basis123 still getting the same error.What would be the porblem even if I try to change the password at Admin>>user ( left side pane below the table names in MDM console) where I can reset the password.If I give password also its taking to old default password & I dont know what was the password given initially.
Thanks In Advance
Sri

hi,
********WinSock error on connect*********
1. check for the repository is loaded or not, if it is not loaded you will get winsock error, load the repository and log into import manager/ data manager, it will work.
2. The default user ID: Admin , Password : ( leave it blank), it will work.
hope this may help you,
Regards,
Srinivas

Similar Messages

Error when connecting to MDM from different lan

Hi,
I got "Image Server Login Error" when connecting with client to server from different LAN, server is up, and i can connect to it when i in the same LAN. Ports 20003, 20004, 20005 for MDM server discovering and repository port 2345 is accessible through router. Running SP2 5.5.24.06.
Rem: it's not a port problem, when port 2345 is closed i got "WinSock error on connect"
PS: When I used MDM SP1 i connected to him properly in the same case.

Hi Dmitry,
If your repository is set to port 2345, then 4 subsequent ports should be openned also, i.e. 2346-2349.
Regards, Lev

Winsock error when doing MDM sync

Hello
I am running MDM Server 5.5 sp3 and I frequently (not all the time) get a popup while synchronizing an existing slave that says "Winsock error on connect".
It seems like this interrupts the sync, so I re-run the sync and it usually finishes ok.
Any help would be appreciated.
Thanks
Dave

Shiv
Thanks for the reply.
Your answer makes sense except this happens a few minutes after the sync has started, I am already connected. If I just run the sync again it will finish ok.
I guess it could be that I am getting intermittent disconnects to database? Is this possible? Database connection is on a dedicated gigabit network.
Any ideas?
Thanks
Dave

Error sending emails to Internet: Failed to connect. Winsock error code: 10051

Our exchange 2013 CU2 (CAS+MBX, Win2012) was sending emails to Internet using another server (a kerio email server) and outbound internet email was working as expected.
We have now removed the Kerio server, I also removed the kerio_Send_Connector I was using to send emails to internet and I also changed the email domain in Exchange to be authoritative. I created a new Internet send connector with default values, but the same
bad behavior is present.
Our Exchange 2013 receives emails internally and externally with no problems. The problems are sending emails to Internet. I am suspecting something in the firewall but i need to do some more research.
If from the same Exchange server I telnet to an Internet email host:25 I do get the smtp banner but as soon as I start typing HELO/EHLO I get disconnected and errors are logged.
Errors when sending emails to any emails address (this is from an email sent to google, all others are the same):
Remote Server at aspmx3.googlemail.com (74.125.136.26) returned '400 4.4.7 Message delayed'
7/1/14 9:52:44 a. m. - Remote Server at aspmx3.googlemail.com (74.125.136.26) returned '441 4.4.1 Error encountered while communicating with primary target IP address: "Failed to connect. Winsock error code: 10051, Win32 error code: 10051." Attempted
failover to alternate host, but that did not succeed. Either there are no alternate hosts, or delivery failed to all alternate hosts. The last endpoint attempted was 74.125.136.26:25'
I cannot find any references from such Winsock error that are related to Exchange 2013.
So far all email is being queued at the Exchange Server 2013. I am afraid to install CU3 and make things worse.
Thanks for your comments.

Just check if the receive connector settings are set to fine
check the send connector properties and see whether it is set to use DNS to route emails through external DNS/Internal DNS or smart host .
Do a telnet to external domain like hotmail,yahoo and see at what transaction you are getting an error
Enable verbose logging, restart the transport service and check if you get the same error in the verbose logs as well
Get in touch with the ISP and see if the port 25 for Outbound SMTP is opened.
YOu can check if SMTP Proxy is enabled in the firewall. If so disable the SMTP proxy in the firewall and check.
Good Luck!!
Please mark as helpful if you find my contribution useful or as an answer if it does answer your question.
That will encourage me - and others - to take time out to help you.
Regards,
Sathish

Winsock Error on Send

Hi All,
I am getting "winsock error on send " while trying to mount the server in console.
Kindly suggest the cause.
BR
SK

Hello SK
If you use Windows server for SAP MDM Server installation you can install MDM Console to the same place.
Install it and check your connection to MDS.
If from server MDM Console work fine and from another PC doesn't work (you get error message).
Check your phisical connection to server(where MDS has installed) from your local PC.
Check your locval and server firewall or antivirus software configuration - may be it's blocked some ports like:
MDS
Port 59950 and three sequential ports
from the range 2000 - 9999 for every
loaded repository (the repository ports
are configurable using the MDM
Console).
MDIS
Port 59750
MDSS
Port 59850
MDLS
Port 59650
I think that is help you
Regards
Kanstantsin Chernichenka

HT2731 I am unable to access my iTunes store through my iTunes account. Every time I have tried it gives me an error ' cannot, connect to iTunes'

I am unable to access my iTunes store through my iTunes account. Every time I have tried it gives me an error ' cannot, connect to iTunes'

check to see if you are online
check to see if you can access secured websites (https) on your computer / device
if this is on a computer with windows configuring your antivirus / firewall to not block itunes some times will help, also resetting your tcp/ip might fix it (open command prompt as an administrator, type: "netsh reset winsock" hit enter, restart computer

A *** ERROR = RFC ====== connection closed (no data)

I trace data On Instance DEV_W0 the had Error as below
A *** ERROR => RFC ======> connection closed (no data)
Please Kindly verify the cuase and recommend in this issue .
Edited by: SoeyTH on Dec 6, 2010 3:38 PM

You need to proivde more logs to find what caused.
Is you SAP up?

Creating new Data Source Error - Database connection Failed

Successfully installed and configured 11.1.1.3.0. Planning and Essbase dev.
Went to Workspace > Administer > Classing Planning Administration > Manage Data Sources > Create Data Source.
Entered all info about the application database , etc. Getting error "The database connection failed" (I was able to connect with no problem during the install)
SQL server 2005 is on the same physical server.
The diagnostic tool shows database connection passed for planning. A new database was created for the new application.
The server event viewer shows these errors.
"Login failed for user 'xxx-hyperion'. The user is not associated with a trusted SQL Server connection."
Group Policy Error "The client-side extension could not apply computer policy settings for 'Default Domain Policy {xxx}' because it failed with error code '0x80070003 The system cannot find the path specified.' See trace file for more details. "
The Group Policy client-side extension Group Policy Services failed to execute. Please look for any errors reported earlier by that extension.
Any help is appreciated.

Datasource for the application.
I have created a sql db for this planning application (my datasource). See my first message for more details.
When you create a new planning application, you need to associate it with a data source. Since this is a new install, I don't have any data sources available yet.
So, "To create, edit or delete data sources, click Manage Data Source."
This page lets you validate your connection to the database and essbase server. My essbase server connection validates! The database connection does not validate after I enter all the relevant information.
SCREEN INFO BELOW
Fields displayed with an asterisk (*) are mandatory.
Data Source Name *:
Data Source Description:
Select Database Platform
Microsoft SQL Server
Application Database
Server * :
Port * :
Database *:
User *:
Password *:
Click "Validate Database Connection"
ERROR ---> Database connection failed.
So it does not let me create a data source for my new planning application, so I cannot create a new planning application.
Thanks in advance.

I have lost the ability to upload files to a website. I have to transfer files from my computer to a web site and I get an error message "connection was reset" and the file will not upload. I try to transfer pictures and I get the same message.

I have to upload a scanned receipt to a website and I get the error message "connection was reset". I have uploaded these receipt for two years and last week I have had to use another browser to complete this operation. I connect to the website and do the report I must do, but I can no longer upload to this site.

Are you using any additional software for the uploading?
Try using Firefox in [[safe mode]] when you upload. There is no need to make changes when you see the option. Disable all plugins whilst in safe mode. Then try the uploads.
You mention [/questions/921993 elsethread] that it is a work site. Have you contacted your IT department. One possibility is that the site is not recognising Firefox 10.
(One temporary workaround and troubleshhooting test would be to install Firefox3.6.27 [http://portableapps.com/news/2012-02-01_-_firefox_portable_3.6.26_released portable] as an additional browser and try that.)

Android MS RDP - RPC Error: Your connection was denied because of a Resource Access Policy (TS_RAP). Please contact your server administrator. (2147965402).

I love iTap Mobile. Paid for the app. Sorry to see them discontinue it, but now I know why. Microsoft bought them out! But even though free, I am getting an error: RPC Error: Your connection was denied because of a Resource Access
Policy (TS_RAP). Please contact your server administrator. (2147965402). I worked with iTap to fix this so I guess they sold Microsoft their older buggy code... Microsoft, please fix!
PS: This is the Android version. Mac and iOS are both okay.
EDIT: After an update a few months ago, iOS is no longer working. Not sure if the problem is related to the Android MSRDP issue.
UPDATE - Relevant posts (need Android RDP software engineer to fix):
Event Viewer Log when using Android client:
The user
"DOMAIN\testuser", on client computer "10.x.x.x", met connection authorization policy requirements and was therefore authorized to access the RD Gateway server. The following authentication method was used: "NTLM". (This
is most likely for logging into RD Web - icons shows up).
The
user "DOMAIN\testuser", on client computer "10.x.x.x", did not meet resource authorization policy requirements and was therefore not authorized to resource"localhost".
The following error occurred: "23002". (This is after clicking on any
of the icons).
I
think the Android MS RDP client is providing the incorrect resource. It shouldn't be "localhost".
It should be the RD Connection Broker's hostname, I believe.
Here's what it should look like (connected using a Windows PC going
through the RD Web portal via Internet Explorer):
The user "DOMAIN\testuser", on client computer "10.x.x.x", met connection
authorization policy requirements and was therefore authorized to access the RD Gateway server. The following authentication method was used: "NTLM".
The user "DOMAIN\testuser", on client computer "10.x.x.x", met resource
authorization policy requirements and was therefore authorized to connect to resource "rdsfarm.domain.com".
The user "DOMAIN\testuser", on client computer "10.x.x.x", connected
to resource "rdsfarm.domain.com".
Stephan,
Do you have any way to contact the software engineer who worked on the Android version of the RDP client? Please
have them read this thread. They need to fix the hard coded "localhost" resource to be a variable (namely whatever the user put in for the server).
This is why the MS RDP app is failing in situations where the FQDN for the RD Gateway and Connection Broker uses
the same host name.
Again, this is not a configuration problem on our end as it works as intended with the native Windows RDP client
as well as the Mac and iOS version of the mobile RDP client (all based on iTap Mobile's RDP app).
This is a problem specific to the Android RDP app.
PS: No matter how hard I try, the WYSIWYG editor is not very WYSIWYG at all, and so everything here looks messed up even though it looked right when I posted it (it is deleting new blank lines I'm inserting to make it spaced out and easier to read). See
below to read the post in context.

Thanks for the bumps, everyone. I haven't check this thread in a while because I basically gave up on Microsoft's ability to respond. Unlike paid apps, there's no number to call or ticket to open when an app like this malfunctions.
Just to give you an update, iOS users started having issues connecting a few months ago. I don't remember what version started this. I'm not sure if it's the same problem.
Also, the newest version now gives a slightly different error message: RpcOverHttpEndpointException: 2, Your connection was denied because of a Resource Access Policy (TS_RAP). Please contact your server administrator.
For Android users, I am starting to recommend Xtralogic Remote Desktop Client. It's a paid app, but it works great. I don't know of any alternative for iOS.
MSRDP for Mac OSX (was also an iTap application) continues to work throughout the many updates.
We need a software engineer from MS to read my first post. All the information that will point to a fix is there. I strongly believe someone hardcoded the string "localhost" instead of using a variable to point to the FQDN of the rdsfarm
name.
Here's that info again (copied/pasted). It doesn't take an engineer to understand the issue. If you know how to decipher Event Logs, you can see where the problem is.
Event
Viewer Log when using Android client:
The
user "DOMAIN\testuser", on client computer "10.x.x.x", met connection authorization policy requirements and was therefore authorized to access the RD Gateway server. The following authentication method was used: "NTLM". (This
is most likely for logging into RD Web - icons shows up).
The
user "DOMAIN\testuser", on client computer "10.x.x.x", did not meet resource authorization policy requirements and was therefore not authorized to resource"localhost".
The following error occurred: "23002". (This
is after clicking on any of the icons).
I
think the Android MS RDP client is providing the incorrect resource. It shouldn't be "localhost".
It should be the RD Connection Broker's hostname, I believe.
Here's
what it should look like (connected using a Windows PC going through the RD Web portal via Internet Explorer):
The user "DOMAIN\testuser", on client computer "10.x.x.x",
met connection authorization policy requirements and was therefore authorized to access the RD Gateway server. The following authentication method was used: "NTLM".
The user "DOMAIN\testuser", on client computer "10.x.x.x",
met resource authorization policy requirements and was therefore authorized to connect to resource "rdsfarm.domain.com".
The user "DOMAIN\testuser", on client computer "10.x.x.x",
connected to resource "rdsfarm.domain.com".

Outlook 2013 error: The connection to Microsoft Exchange is unavailable

Environment: Windows 7 Enterprise
Setup: Fresh install of Office 2013
Issue: When I launch Outlook I get the error:
The connection to Microsoft Exchange is unavailable. Outlook must be online or connected to complete this action.
Steps to resolve:
I made sure my server name and mail address were correct but this did not have an impact.
I am at a total loss on how to resolve this issue, is there anyway to manually connect to M.E> as it is just saying the connection is unavailable. All of the other threads dealing with this issue have been no help. I can sign into my account
at login.microsoftonline.net so i know the account is valid. I also receive email to my iPhone with the account and server. Any advice would be wonderful.
Now when I start up the application it tells me the same error and brings up something to alter the server and connection address.

Hi,
Have you tried to recreate a new mail profile and then test the issue?
To do this, please exit Outlook, and then go to
Control Panel >Mail... > Add…
Details about create a new mail profile, see:
http://support.microsoft.com/kb/829918/en-us
Also, you can try with this KB:
http://support.microsoft.com/kb/2264398
This issue occurs when the
HKEY_CURRENT_USER\Software\Microsoft\Windows\CurrentVersion\Explorer\User Shell Folders registry key does not contain all of the required data. Specifically, these problems occur if the
AppData string value is missing from this registry key.
To resolve this issue, import the
User Shell Folders registry key from a working Windows User Profile.
Hope this helps.
Best Regards
Steve Fan
TechNet Community Support

When i want to update my iphone 4 it shows an error on connection. how can i update to the new version software?

every time that apple takes out a new update i cannot update my ipohone 4 it gives me on itunes an error of connection can someone please help me out on what to do

Try temporarily disabling your firewall and antivirus software and try again...
See here for Connection Issues
http://support.apple.com/kb/TS1379
From Here
http://www.apple.com/support/itunes/troubleshooting/

Error in connection to SEM, changes will not be saved

Hi All,
When i am creating an opportunity i am getting an error
"Error in connection to SEM, changes will not be saved", and it does not allow me to save the opportunity.
Regards,
Radhika

Dear Mangesh,
Thank you for your post. It's really helpful.
Best Regards,
Duc Lam.

Message "Error in connection:No result set, result attempts = 100" on VC

Hi,
I am using a JDBC datasource to retrieve, update, insert and delete information from a SQL Server database using executing store procedures from VC.
The selection of the data is perfect but for the deletion, insert or update of any data using store procedures I always get the following message:
"Error in connection:No result set, result attempts = 100"
At the end the information is modified in the database but I get error.
Here is an example of one of my store procedure:
CREATE PROCEDURE [dbo].[DelData]
     @id uniqueidentifier
     -- Add the parameters for the stored procedure here
AS
BEGIN
     -- SET NOCOUNT ON added to prevent extra result sets from
     -- interfering with SELECT statements.
     SET NOCOUNT ON;
    -- Insert statements for procedure here
     delete from data
       WHERE Rowid=@id;
END
Let me know if somebody knows the reason of this and if there is something that I am doing wrong.
Thanks,
Zareh

Hi,
when you SELECT data, you get a result. So your connection gets a result set. When you DELETE, INSERT,... you have no result, because you didn't select data. So your connection can't get any result sets.
best regards,
Christian

Error while connecting to workflow builder after installation...first time!

Hi,
I have installed Oracle Workflow Builder 2.6.3 recently on my system and after installation, when I am trying to connect the workflow builder (using database username/password of that particular instance), it is throwing me the following error:
220: Unable to set NLS_LANGUAGE.
210: Oracle Error: ORA-01403: no data found
. SQL text: SELECT NLS_LANGUAGE FROM WF_LANGUAGES WHERE :l IN (NLS_LANGUAGE, CODE)
In the previous threads when I searched for the same issue, I found that if
select value from v$nls_parameters
where parameter='NLS_CHARACTERSET';
returns the value other then WE8ISO8859P1 then that is what I should change my NLS_LANG entry for the builder - i.e. AMERICAN_AMERICA.<character set>.
But I am not getting where should I change NLS_LANG, it is located where...some file? I am new to Workflow.
Please help me. I tried a lot. Any type of help will be highly appreciated.
Thanks,
Sumir

This issue (and solution) is described in ML Doc 577905.1 (Error While Connecting To Database Via Workflow Builder)
HTH
Srini

WinSock error on connect

Similar Messages

Maybe you are looking for