Wireless 1310 intermittent issues

we have a link between two 1310 bridges and for a few months everything was fine.
now, every so often we get high response times when running a ping. The average response normally is around 2ms peaking to 7ms but every so often it spikes to say 300ms and then 700ms. Also, Every so often we see that the link goes down and the logs say deauthenticated and then no response. we have to reboot the wireless bridges (BOTH OF THEM) then this works after a reset.
any ideas?

There are several reasons for an intermittent connectivity issue to occur with a building to building Wireless bridge setup.
Reasons like RF Interference, Fresnel Zone, Clear Channel Assessment etc are there. The following document should give you a clear picture on this
http://www.cisco.com/en/US/products/hw/wireless/ps469/products_tech_note09186a0080508551.shtml

Similar Messages

  • Wireless Problem intermittent connection

    Hi,
    We have three WLC on our network that runs all at the same time. We experienced intermittent connectivity and all we did was reload the WLC3 to make it normal again. I attached the logs of the three WLC below. Hope someone can help. Thanks!

    Well try upgrading the firmware of the router & keep on holding tightly
    the reset button in such a way that power light is blinking on the
    router & then do a complete network power cycle i.e., unplug the power
    cables from the modem & from the router & then plug in the power cable
    to the modem first once all the lights are solid green you could plug
    in the power cable to the router & check out it will definately work!! & according to your Internet Service Provider configure the router & you should be able to go online wirelessly without any issue.

  • CRM 7.0 Unable to open/view PDF Attachments in Email (Intermittent issue)

    Hi,
    Unable to open an attachment (PDF format) sent from exchange server(Lotus) to SAP CRM,Actually its an intermittent issue When i try to open email in UI ,getting an error message "File is damaged and couldnot be repaired".
    I understand that PDF attachment wasn't delivered(Synchronization issue between Lotus and CRM) to SAP CRM system properly by the exchange server ( Lotus ).Hence the particular attachments are not able to view/open in SAP CRM system.
    Is there anyway to trace and find out root cause of the issue?
    Regards,
    Shan

    Issue with IE version and some PDF wasn't delivered properly by lotus exchange server

  • Having an intermittent issue where my iMac blanks out on me. On restarting I get bands running down the screen with pixels jumping around, then the white screen of death and nothing... Wouldn't restart all weekend, now fine..? any ideas whats wrong?

    Having an intermittent issue where my iMac blanks out on me. On restarting I get several bands running down the screen with pixels jumping around within the bands, then the white screen of death and nothing... This happens intermittently and usually restarts OK. Happened again three days ago and wouldn't restart for two days (again the bands/pixels etc) but now operating fine? Any ideas whats wrong with my iMac and what the solution may be? Also gets very hot from time to time, particularly if I'm playing music/watching youtube/movies for extended periods. Mac is 3.5 years old, running OS X 10.6.8, processor 3.4 GHz i7 memory 8GB 1333 MHz DDR3

    If you live near an Apple Store, make a Genius Bar appointment to have the computer tested. Supposedly there is no charge for testing. Use 2nd link if not near an Apple Store or aren’t in the US.
    Genius Bar Reservation US
    Authorized Service Provider

  • ADF popup is not showing - Intermittent issue

    Guys,
              Once in a while popups inside the adf application are not showing up. have anybody faced this issue?
    Though its rare, i would like to know the reasons behind this intermittent issue.
    Any pointers/thoughts will be appreciated... Thanks

    Popup if very problematic item in ADF.
    There are 2 ways to invoke the popup correctly
    1. Make sure that you don't have a combination of viewScope and backingbean scope in everything related to your popup
    2. Or (and this is the best one) - don't use popup. Create a bounded task flow and call it from your task flow. You have an option to call it as inline popup.

  • Hi, Using MAC OSX 10.6.8 and have intermittent issues with receiving new emails - sending is OK. I've tried the workarounds (take offline & take online), quitting mail etc - no luck. Any suggestions?

    Hi, I'm using MAC OSX 10.6.8 and have intermittent issues with receiving new emails - sending is OK. I've tried the workarounds (take offline & take online), quitting mail etc - no luck. Have cleared space, checked Window - Doctor and server has green light.  Mail Activity shows 47 emails waiting to download, iPad and iPhone download them all OK - no extra big files stopping the download either.    In the past, quitting mail has worked, but not today... Any suggestions?

    Hi, I'm using MAC OSX 10.6.8 and have intermittent issues with receiving new emails - sending is OK. I've tried the workarounds (take offline & take online), quitting mail etc - no luck. Have cleared space, checked Window - Doctor and server has green light.  Mail Activity shows 47 emails waiting to download, iPad and iPhone download them all OK - no extra big files stopping the download either.    In the past, quitting mail has worked, but not today... Any suggestions?

  • Intermittent issue : Portal theme not loaded for WDA, BSP iViews

    Hello,
    We are facing intermittent issue in Portals where theme is  not loaded for WD ABAP & BSP iViews.
    As theme isn't loaded, the layout of these iViews is distorted, it renders in plain HTML format.
    And this is random behaviour and often not reproducible.
    During one such occurrence, we could manage to capture "ERROR_INTERNET_CONNECTION_RESET" error when theme URL (a CSS file) is called.
    Attached is the screenshot from HttpWatch.
    Please suggest.
    Thanks & Regards,
    Amey Mogare

    Hi Amey,
    Try checking these SAP Notes:
    1517914 - Themes & Styles - Specific Component Note
    1818426 - WDA: Portal style sheet is not used
    1000889 - CSS Style Sheet Integration of Web Dynpro and the Portal
    Best regards,
    Cristiano L. Mazzotti

  • Facing intermittent issue with findByAltKey api

    We are facing an intermittent issue with findByAltKey while invoking from service in out code and so we want to understand the expected behavior of this api
    the issue is we have an unposted row in the cache which we need to retrieve.So we are doing a findByAltKey and based on the alternate keys it should return the row,but it fails sometimes.
    We noticed while debugging that one of the alternate key attributes that we have defined on our EO is "Name" and the value of name in the EntityCache is sometimes becoming null.As a result of this the alternatekey attributes we pass doesnt match the EO.getAltKey(index) and it in turn doesnt fetch the row.
    This attribute "Name" is present both in the base table and the translation table and there is a view link from parent VO to the TL(translation) VO.
    What we want to understand here is when we do a findByAltKey based on name ,from where does it gets the name from the base vo or translation vo? And is it because of this sometimes this value in the cache is null?
    Can anyone please explain the above issue.

    Hi,
    Which SOA server you are using?
    A & B are synch or Asynch processes?
    Thanks
    Arik

  • Intermittent Issue in ALUI 6.5

    I am facing an intermittent issue while retrieving Adaptivepagelayouts from the imageserver. I have two different layouts. One is applied on the unauthenticated part and the other one is applied to authenticated part on the same site. While navigating from the unauthenticated part to authenticated part, the new page layout is picked and rendered as per defined in experience rules. Here the issue is that sometimes the page layout for the authenticated side fails to be picked and the authenticated side comes up with the Adaptive pagelayout meant for the unauthenticated part. This distorts the whole design of the page. I am not sure of what could be the exact reason for this, as 50% times it works fine and 50% times it goes wrong. Moreover the ALUI admin and the image server is continuously being worked upon by other developers, so not sure if that might have caused the issue...but then why this intermittent thing. Moreover, imageserver and ALUI is placed on two different servers.
    Kindly help me out as I am new to portal. Thanks for all your help in advance :)
    PTSpy logs says :
    152 3-7-2012 7:46:50.390 Error Portal_UI_Infrastructure portal.SERVERNAME.UserName .NET #7 com.plumtree.portaluiinfrastructure.layout.impl.LayoutManager             LayoutManager:GetLayout Could not begin processing web service with Id: 491
    com.plumtree.server.marshalers.PTException: -2147203531 - Layout with web service ID: 491 returned error code: -2147203531 and error message: Portlet request failed, the remote server returned HTTP error '400'.  Web Service ID=491, User ID=126781, URL='http://hostname/plumtree/portal/private/pagelayouts/XXXX/BasePageLayout/authenticated.html'
    com.plumtree.server.marshalers.PTException: -2147203531 - Layout with web service ID: 491 returned error code: -2147203531 and error message: Portlet request failed, the remote server returned HTTP error '400'.  Web Service ID=491, User ID=126781, URL='http://hostname/imageserver/plumtree/portal/private/pagelayouts/XXXX/BasePageLayout/authenticated.html' at com.plumtree.portaluiinfrastructure.layout.impl.LayoutManager.GetLayout(Int32 nWebServiceId, AActivitySpace asSpace) in e:\buildroot\Release\portalui\6.5.x\ptwebui\portaluiinfrastructure\dotnet\prod\src\com\plumtree\portaluiinfrastructure\layout\impl\LayoutManager.cs:line 82
    at com.plumtree.portalpages.common.uiparts.PlumtreeDP.DisplayLayout(Int32 nWebServiceID, Boolean bMainPage)
    at com.plumtree.portalpages.common.uiparts.PlumtreeDP.DisplayLayout(Layouts layout)
    at com.plumtree.portalpages.common.uiparts.PlumtreeDP.Display(IWebData pageData)
    at com.plumtree.uiinfrastructure.interpreter.Interpreter.HandleDisplayPage(Redirect myRedirect, RequestData tempData) in e:\buildroot\Release\uiinfrastructure\6.5.x\dotnet\prod\src\com\plumtree\uiinfrastructure\interpreter\Interpreter.cs:line 1817
    at com.plumtree.uiinfrastructure.interpreter.Interpreter.HandleRequest(IXPRequest request, IXPResponse response, ISessionManager session, IApplication application) in e:\buildroot\Release\uiinfrastructure\6.5.x\dotnet\prod\src\com\plumtree\uiinfrastructure\interpreter\Interpreter.cs:line 539
    at com.plumtree.uiinfrastructure.interpreter.Interpreter.DoService(IXPRequest request, IXPResponse response, ISessionManager session, IApplication application) in e:\buildroot\Release\uiinfrastructure\6.5.x\dotnet\prod\src\com\plumtree\uiinfrastructure\interpreter\Interpreter.cs:line 163
    at com.plumtree.uiinfrastructure.web.XPPage.Service(HttpRequest httpRequest, HttpResponse httpResponse, HttpSessionState httpSession, HttpApplicationState httpApplication) in e:\buildroot\Release\httpmemorymanagement\6.5.x\dotNET\src\com\plumtree\uiinfrastructure\web\XPPage.cs:line 81
    at com.plumtree.portaluiinfrastructure.activityspace.PlumHandler.ProcessRequest(HttpContext context) in e:\buildroot\Release\portalui\6.5.x\ptwebui\portal\dotnet\prod\src\web\PlumHandler.cs:line 36
    at System.Web.HttpApplication.CallHandlerExecutionStep.System.Web.HttpApplication.IExecutionStep.Execute()
    at System.Web.HttpApplication.ExecuteStep(IExecutionStep step, Boolean& completedSynchronously)
    at System.Web.HttpApplication.ApplicationStepManager.ResumeSteps(Exception error)
    at System.Web.HttpApplication.System.Web.IHttpAsyncHandler.BeginProcessRequest(HttpContext context, AsyncCallback cb, Object extraData)
    at System.Web.HttpRuntime.ProcessRequestInternal(HttpWorkerRequest wr)
    at System.Web.HttpRuntime.ProcessRequestNoDemand(HttpWorkerRequest wr)
    at System.Web.Hosting.ISAPIRuntime.ProcessRequest(IntPtr ecb, Int32 iWRType) <ptLogMsgEnd>

    I would suggest you post your question on the WebCenter Interaction forum.
    WebCenter - Interaction
    Brad

  • Ie8 causing intermittent issues on forms application

    Version 10.1.2.3.0
    Forms Builder 10.1.2.0.2
    We are encountering intermittent issue on our forms application where if you click on a text field, the mouse cursor does not go there and if you click on certain tabs, nothing happens. We have also noticed issues where if you click on menu items, then there is a 4-5 seconds delay in response.
    Using Jave Runtime 6 update 15.
    Has anyone encountered the same issue.
    I have checked the Oracle page below and it says thay IE 7 is supported.
    http://www.oracle.com/technology/products/forms/htdocs/10gR2/clientsod_forms10gR2.html
    Also looked on metalink and it says that IE8 is
    recommended Browsers for Oracle E-Business Suite 11i, but we are 10G.
    Has anyone found the cause or solution?
    Thanks
    Found another article
    http://blogs.oracle.com/stevenChan/2009/09/internet_explorer_8_certified_ebs12.html
    Edited by: Forms_Reports_Beginner on Oct 22, 2009 1:59 PM

    Satya,
    With web deployed Forms, any call to the database is going to cause your form to run slower due to the time it takes to send and receive data from the database. Web deployed Forms require you to change the way you develop a Form in order to reduce the number of calls to the database. Excessive COMMITs in a Form could certainly cause your Form to run slower.
    If your Form is issues a FORMS_DDL('COMMIT') call right after a Do_Key('COMMIT_FORM') then this is redundant is not necessary. If you look at the definition of the Forms_DDL built-in you'll find that the purpose of this built-in is to issue dynamic SQL statements during run-time and the built-in issues an implicit COMMIT at the end of the transaction. This implicit COMMIT is independent of the Forms transaction so any pending changes in the Form are not affected by the implicit COMMIT. Whereas, the call to COMMIT_FORM causes your Form to update data in the database to match your Form changes. Not only does COMMIT_FORM commit your Forms changes, but it also commits any pending database changes your Forms session may have created.
    I recommend you look through your Form and remove any redundant COMMIT calls. Also, look at your Post-Query triggers and try to reduce or remove any database calls you have there as well.
    Hope this helps.
    Craig...
    If a response is helpful or correct, please mark it accordingly

  • Intermittent issues with video output initialization

    Hi Guys,
    I have received a new (i5, 15') Mac-book Pro more than 9 months ago. About 6 months ago it started having some serious intermittent issues with video output. Those issues are numerous and different every time, but all seems to lead to GPU problem. In chronological order:
    1)Started showing static colors as flickering and white color as blue.
    2)Blue screens in bootcamp and hangs in mac os
    3)Startup problems (fail to start)
    4)Startup problems resolved with firmware patch, but video fails to initialize during startups:shows black on mac os, and distorted green during bootcamp.
    So right now I am stuck with #4. The main issue is that it is intermittent - sometimes it starts to happen and sometimes it does not. Is there any way I can make apple replace the unit or the video-card? I did bring it to a apple certified service center, but they did not give any crap, even when I was able to demonstrate it to 2 people in there and gave me back the unit after failing to reproduce the problem on their own. I have all those problems in video and photos, but I don't see anywhere I could send them besides this forum.
    Some of the evidence (I have much more):
    http://www.youtube.com/watch?v=MsTYnUFCX1I
    http://www.youtube.com/watch?v=zK85Hi9gx24
    http://www.youtube.com/watch?v=pRH3DpN7qB0
    http://www.youtube.com/watch?v=dMXo8qF6S_k
    Message was edited by: Breakable

    "I have received a new (i5, 15') Mac-book Pro more than 9 months ago."
    You are still under warranty. *Call AppleCare*
    "Is there any way I can make apple replace the unit or the video-card? I did bring it to a apple certified service center, but they did not give any crap"
    No you cannot make Apple do anything. What you can do is call _Apple Customer Relations_ in your country. You can call AppleCare & ask politely & firmly to be transferred over to Customer Relations if there is no direct phone number like there is in the US. Relay to them what you stated in this post. See what they can do for you.
    You posted in the wrong MBP area (Original). I have requested that a HOST move your post to the proper forum MacBook Pro (2008 and Later). There will be no need for you to repost.

  • Intermittent issues when publishing FSG Reports to Excel

    Hi,
    Could you assist me.
    Our Client are on 12.1.3 and are having intermittent issues when trying to publish FSG's to Excel. At times it sucessfully works straight away and other times it wont do anything.
    They state "When a report is published it will open Excel show some purple/yellow formatting will show but will then quickly revert to a blank spreadsheet and goes no further or completes".
    Has this been seen before?
    Many Thanks
    Matt

    Did you customize the existing templates? Please let me know the template name (seeded) which seems to create problem.
    Cheers,
    ND
    Use the "helpful" or "correct" buttons to award points to replies / Mark the thread as answered, if your question is answered.

  • TS3899 Intermittent issue with sending emails from a blueyonder.co.uk email address.

    Hi can anyone help?  My iphone 4 has recently developed an intermittent issue sending emails from my 'blueyonder.co.uk email account.  The emails get delivered to my outbox with a message 'cannot send mail, recipient was rejected by the server'  When the emails are in my outbox there is no means to delete them there the only way to remove them is to remove the full email account and reset it up again.
    I have tested the send functionality with my Gmail account and this seems to work ok!
    I have spoken to Virgin Media my email provider and they have walked me through removing the account and resetting it up again but to no avail.  They have suggested I contact Apple as there appears to be something wrong with the email application on my phone for this particular email account. 
    All incoming emails are being received as normal

    Hi can anyone help?  My iphone 4 has recently developed an intermittent issue sending emails from my 'blueyonder.co.uk email account.  The emails get delivered to my outbox with a message 'cannot send mail, recipient was rejected by the server'  When the emails are in my outbox there is no means to delete them there the only way to remove them is to remove the full email account and reset it up again.
    I have tested the send functionality with my Gmail account and this seems to work ok!
    I have spoken to Virgin Media my email provider and they have walked me through removing the account and resetting it up again but to no avail.  They have suggested I contact Apple as there appears to be something wrong with the email application on my phone for this particular email account. 
    All incoming emails are being received as normal

  • Intermittent issue with Wifi network card.

    Nothing can be more annoying than an intermittent issue. Unfortunately it does happen to my MBP. This is the new MBP purchase Jan. of this year. About 2 months ago, the MBP developes a problem. The sympotom is, after powering it on, the Wifi network card sometimes suddently stop working, even cannot be recognized by the system accidently. After the problem arise, I cannot turn on wifi again. The only way to get it back is to restart it. It used to work well with my home network and company network.
    I have tried every possible mean to figure out what's wrong with it. Tried SMC reset, PRAM rest. Reinstall a new OS on a new partition (per instruction from Apple support). I hate to say this is a HW issue but support people from Apple did suggest sending it to a service center for a check up.
    Before I actually dropping it at service center, I wanna know if someone has experienced that before?
    Repeat, it used work well with my router.

    senthil,
    It helps to describe your setup parameters.
    Which antenna(s) do you have?  Either 2 internal antennas or 1 external antenna.
    How far away and what obstructions (walls - wood/concrete) is the wi-fi router?
    I am a volunteer. I am not an HP employee.
    To say THANK YOU, press the "thumbs up symbol" to render a KUDO. Please click Accept as Solution, if your problem is solved. You can render both Solution and KUDO.
    The Law of Effect states that positive reinforcement increases the probability of a behavior being repeated. (B.F.Skinner). You toss me KUDO and/or Solution, and I perform better.
    (2) HP DV7t i7 3160QM 2.3Ghz 8GB
    HP m9200t E8400,Win7 Pro 32 bit. 4GB RAM, ASUS 550Ti 2GB, Rosewill 630W. 1T HD SATA 3Gb/s
    Custom Asus P8P67, I7-2600k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX660 2GB, 750W OCZ, 1T HD SATA 6Gb/s
    Custom Asus P8Z77, I7-3770k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX670 2GB, 750W OCZ, 1T HD SATA 6Gb/s
    Both Customs use Rosewill Blackhawk case.
    Printer -- HP OfficeJet Pro 8600 Plus

  • Intermittent issues with SAP printing

    Hi ALl, We have been having intermittent issues with printing (more specifically BOL printing) on both ECC production  & Watre house production server recently. These issues occur at random hours and resolve themselves before the teams have had an opportunity to troubleshoot in detail. Also, both the Basis and hosting teams have analyzed the logs but haven’t reached a definite conclusion. Procedure used in printing: An outbound queue is created and processed in Warehouse Production and passed to ECC PRoduction. In ECC PRod an inbound queue is processed to update and trigger the shipment document. When the shipment document is completed it then triggers the print of the BOL output from the shipment. Then and only then is anything sent to the print queue.  AND it will be with user id = ALEREMOTE. The other printing works fine. Any thought..will be highly obliged.. Regards, VIcky

    Doug,
    If you have a service contract feel free to call in to the support line and you'll be able to work with someone on the phone. That'll be the quickest way to resolution.
    Feel free to send me a PM if you wish and I can take a look at the code and test it on our machine. 
    Notes for Branch AE:
    Please reply to This Post within 24 hours
    The US AE is expected to reply to all of your posts within 24 hours. Having this expectation will keep the escalation moving quickly and toward a fast resolution.
    You can also use other communication channels: Phone, Sametime, Lync,etc. to discuss the issue with the US AE. This can help with troubleshooting and quick diagnosis of the issue.
    Click here to provide kudos for a post on this page

Maybe you are looking for

  • How to get a CA certificate installed in the web trust db from java servlet

    Hi all. Hi, I have a web-app that requires a client certificate from a CA. The CA cert is in the trust db of the webserver. And I would like to get the CA certificate (X509Certificate) corresponding to the issuer of the current client certificate of

  • ALV display on more than1 page

    We have a requirement to display ALV in more than one page output. Page 1 is as shown below: PSEG Power, LLC        Exelon Generation                            300 Exelon Way KSB#-W                            Kennett Square, PA 19348                

  • BOE XI R2 Error on failed instance:  Unknown Database Connector Error

    I have a recurring job that runs against a high availability instance of our SAP production server.  This job runs every 15 minutes to make sure that the HAS reporting instanace is available to my BOE environment for reporting.  This morning, one of

  • Deploying CMP's in WebSphereAppServer 5.0

    Hi All..... I'm deploying a CMP in WebSphere I'm using Oracle 9i Database...... Please tell me how to make the settings in websphere for the cmp Please tell me soon.....

  • Problem connecting to Adobe servers

    Hi there and thanx for your help. DW CS5 on Windows 7 Ulitmate For some reason I cannot connect to the Adobe servers. I have perfect connection to the internet with Windows firewall turned off. I managed to connect some time ago but now I cannot. I h