Wireless and cable network working together

How do I set up an apple network to allow wireless and ethernet to work simultaneously for different purposes. At our current location we have internet access through a wireless hub but are networking all computers through ethernet. I need to seperate the data stream to allow internet and email to see the Wireless network and have the data link go through the ethernet. Does anyone know the method to follow to get this to work??
regards
Damian Morris

Why are you wanting the two networks to be isolated?
But like Like Linc said,
Put the priority of the adapters accordingly
System Preferences > Network > (gear symbol next to the '-' sign) Set Service Order
Wifi
Ethernet

Similar Messages

Laser Jet M1217nfwMFP wireless and fax stopped working printer works with usb cord

I have an HP computer 64 bit version. The printer suddenly stopped working wireless, fax stopped working weeks ago. Printer does work with a usb cord. Turning it off (removing elec cord) on both computer and printer, didn't help. Nothing changed that was different to cause either problem.

Hi agueda
I see that your Laserjet M1217 wireless and fax stopped working but the usb connection does work.
I would restore the printers defaults to setup the wireless again.
Touch the setup (wrench button) on the printer, select network config, select restore defaults.
Then make sure the wireless radio is turned on.
Touch the setup button (wrench), network configuration, wireless menu, wireless radio-on.
Temporarily connect the usb cable from the printer to the computer and go to start, all programs, hp, laserjet m1217 and select wireless configuration and go through the wizard to reset up the wireless again.
or if your router has a wps button on it then you touch the wps wireless button on the printer and immediately touch the wps button on the router.
Printer should automatically connect to the wireless network.
Run the add printer wizard.
Go to control panel,(win7) devices and printers then click add a printer, next, select network
highlight printer, next, message installing printer.
Should be able to print over wireless again.
Check fax connections.
Then run a fax test.
Touch the setup (wrench button) on the printer, service, run fax test.
You should have 4 passes.
Change these fax settings on the printer.
private receive-wrench/fax setup menu/ok/fax receive setup/ok/private receive/ok/set it to off
error correction-wrench/arrow to fax setup/ok/all faxes/error correction/ok/set it to off/ok
speed-wrench/arrow to fax setup/ok/all faxes/ok/fax speed/ok//change speed to medium.
clear saved faxes-wrench/fax functions menu/clear saved faxes/ok/ok to clear.
Try sending and receiving a fax.
If you have any further issues please let me know.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Can I make my iMAC and MAC book work together?

I've done the set up to join other networks.....trying to get my desktop and laptop to work together.
Is it even possible for them to keep updated info regardless of which one I enter it on?
If so, please tell me how.
Thank you
Diane

There are various programs like Dropbox that can help you sync two computers over the network, but I still find them kind of a hassle to set up and maintain.
I simply make my laptop the primary storage, and I turn on File Sharing on my laptop. Then on my desktop I just log into my laptop and open files directly over the network. On my desktop I have aliases to my laptop folders so I can get into them in a couple clicks.

Trying to make sense on how and if RBAC and MOAC could work together

Hi All,
We upgraded from 11.5.9 to R12.1.1 in Nov-2009.
Since the time we have upgraded to R12, we are trying to make sense as to how and if RBAC and MOAC could work together.
The use case is as below:
*11i Days*
US Accountant - accesses ‘AR superuser US’
Canada Accountant - accesses ‘AR superuser Canada’
France Accountant - accesses ‘AR superuser France’
Spain Accountant - accesses ‘AR superuser Spain’
North America Financial controller - Switches between 'AR superuser US' and 'AR superuser Canada'
European Financial controller - Switches between 'AR superuser France' and 'AR superuser Spain'
CFO - Switches amongst 'AR superuser US','AR superuser Canada', 'AR superuser France' and 'AR superuser Spain'
Now in R12- (Wow there is MOAC!)
US Accountant - accesses ‘AR superuser US’
Canada Accountant - accesses ‘AR superuser Canada’
France Accountant - accesses ‘AR superuser France’
Spain Accountant - accesses ‘AR superuser Spain’
North America Financial controller - accesses 'AR superuser North America'
European Financial controller - accesses 'AR superuser Europe'
CFO - accesses 'AR superuser Global'
With R12 now there are 3 additional responsibilities.
We have (like most of the other EBS customers) custom responsibilities and so there is maintenance.
More the responsibilities more the maintenance...More the SOD issues.
To prevent creating new responsibilities, we could use the ‘MO: Security Profile’ at the user level BUT that would mean that now these users would have access to multiple OUs for all the responsibilities...that is not good.
What-If: There is only 1 responsibility 'AR SuperUser' and somehow using RBAC, roles are created and assigned to users so that they only have access to specific OUs.
Apparently, MOAC works based on MO:Security Profile that is something that RBAC cannot control.
Am I missing something...RBAC seems to be no good?
In PROD(R12.1.1)- We are expecting that we would end up creating 100+ new responsibilities since we have many shared services users and they all want to benefit from MOAC...Appreciate, if you could please help us understand how we can prevent these 100+ new responsibilities from getting created?
Thanks
Rahul Gupta

Hi Rahul,
your question is quite interesting. I did a lot in the area of RBAC to understand the background.
RBAC mainly allows you to
- group responsibilities
- build hierarchies
- manage low level data access (via VPD)
- Grant permissions (new with R12)
Unfortunately you can't control profile options via RBAC. Therefore, the MO:Sec Profile has to stay on responsibility level. I was playing with the alternative to put this profile option on user level, but also in this case the number of maintenance steps will stay the same.
I would like to share a document with you, what's your email (or search my name in linkedin)?
kr
Volker Eckardt

I have attempted to update my software over 10 times but I get a network connection error. Anyone with the same problem? Got it on the wireless and wired network.

I have attempted to update my software over 10 times but I get a network connection error. Anyone with the same problem? Got it on the wireless and wired network.

Disable all Firewalls & Anti-Virus software...try again.

My colleague and I are working together (from separate MacBooks) to create an iBook for our students. We plan to work on sections separately and combine later. Must we use the SAME template to do so?

My colleague and I are working together (from separate MacBooks) to create an iBook for our students. We plan to work on sections separately and combine later. Must we use the SAME template to do so?

I'm not sure iBA reacts well to this type of editing, not to mention the cumbersome nature of trying to bring everything together in general.
I'd suggest a workflow where one book is handed off, instead. That, or, let the individuals involved create their basic content in Pages, then when ready, use iBA's Insert Pages Chapters menu to string them together. Best to work in a linear fashion and avoid adding/removing/adding/moving portions, etc.
If you must have separate authors, be sure to use the identical template and have them all properly trained up before going forward - trying this as a learning experience may result in an off-putting experience otherwise , with more time spent on chasing knots than on expressing writing skills, etc.

Can I have a wireless and ethernet network?

I want to have a wireless and hardwired/ethernet network in my house. I want to be able to leave one comouter (an eMac that I do most of my work from) connected to the internet via ethernet cable, and then have the Airport Extreme send out the wireless signal (to the laptops, G4PowerBook & MacBook, we also use in the house).
Right now I use my eMac as to send out the wirelss signal, but that required having the eMac on and connected to the internet to then be able to use the internet on our laptops. I hoped that getting an Airport would elimiate having to have the eMac on all the time.
I bought an Airport Extreme at an Apple Store (in Toronto) and the told me that all I needed to do was have the internet going in to the Airport fromthe modem, and then have the ethernet cable coming out from the Airport and to my eMac.
I set it up this way and while the Airport does send out signal to our laptops fine, the eMac does not get any signel from the ethernet cable.
I can't seem to find any information saying that this set up can actually be done. I find a lot of informetion saying that the ethernet-out port on the airport is for things like printers, and not for internet signal.
So, despite what I was told in the Apple Store, can this sort of set up be done? If so, what am I doing wrong?
-Greg

Greg,
Yes, you can do what you describe.
The airport extreme base station has two ethernet ports in the rear.
One is for the WAN port were you connect your modem and the other one is for the LAN port where you connect your computer (or hub, etc.)
Plug in your Airport Extreme like mentioned above. You will have to configure it for the Internet and to Distribute IP Addresses if you Internet Modem is NOT a router.
Then setup your computer via the Ethernet cable and Ethernet connection in your System Preferences > Network > Ethernet ...
Set your Airport connection or Ethernet connection on your eMac to DHCP....
Your Airport Extreme should then assign you an IP address, etc., and you should be able to access the Internet at that point.
Give that a try.

Photosmart C6180 Wired and Wifi not working together

I recently reinitialized my Photosmart C6180 all in one. Since then I can either use it wired or wireless, but not both at the same time as was the case before. Wireless printing works fine when I unplug the network cable. Once I plug it again, it stops printing wirelessly.
The printer name on the network is HPC61890. I can see it assigned an IP address in my router for both the wired card (.34) and wireless radio (.35). The IP for wireless can only be pinged when the cable is unplugged.
Any idea how to fix this?

Hi Danyk,
I would like to help you with your connection issues. You can connect your printer wireless (on a network) and via USB. But you cannot connect wireless and wired (ethernet). Once the ethernet is plugged in it automatically turns off the wireless.
If you could tell me what operating system you are running I can send a link for the up-to-date software and drivers.
Thank you,
I worked on behalf of HP.

My iPad says it's connected to my wifi but nothing works or loads. My xbox and cable box work on my wifi. Please help?

My iPad says it's connected to the wifi but nothing loads. My xbox and cable box connect and work just fine.

Hey JnastyCL,
Thanks for the question. The following resource outlines the basic troubleshooting steps for Wi-Fi connectivity. I have also included the steps specific to the symptoms you are experiencing:
iOS: Troubleshooting Wi-Fi networks and connections
http://support.apple.com/kb/TS1398
Be sure you're in range of your Wi-Fi router (access point).
Tap Settings > Wi-Fi and turn Wi-Fi off and on. If your W-Fi setting is dimmed, follow these steps.
Confirm that your Wi-Fi router and cable or DSL modem are connected to power, turned on, and connected to the Internet. If not, refer to your network administrator or Internet service provider (ISP) for assistance.
Restart your iOS device.
Tap Settings > Wi-Fi and locate the Wi-Fi network to which you're connected.
Tap and Forget this Network.
Try to connect to your desired Wi-Fi network.
Note: You may need to enter your Wi-Fi password again if your network requires one.
Turn your Wi-Fi router off and on. If your ISP also provides cable or phone service, check with them before attempting this step to avoid interruption of service.
Update your device to the latest version of software.
Update your Wi-Fi router to the latest firmware. For AirPort Base Stations, install updates using the AirPort Utility.
Unable to access the Internet while connected to Wi-Fi
If you're using a public or commercial network, you may need to log in or subscribe.
Check to see if you have a self-assigned IP address:
Tap Settings > Wi-Fi and locate the Wi-Fi network to which you're connected and tap ( i ) .
If your IP address is 169.254.xxx.xxx, you may not be able to access the Internet.
If you do not have a self-assigned IP address, see if other Wi-Fi devices on your network have Internet access.
If they do not, consult with your network administrator or ISP for further assistance.
If they do, reset network settings on your device by tapping Settings > General > Reset > Reset Network Settings. Note: This will reset all network settings including:
previously connected Wi-Fi networks and passwords
recently used Bluetooth accessories
VPN and APN settings
Thanks,
Matt M.

Do Adobe Palettepanel and Adobe Air work together?

Hallo!
when I am working with Flex and the Adobe Flash Player everything is fine. I even can use the Adobe Paltettepanel to integrate my Flex applications in Adobe Indesign.
But when I want to use the Palletepanel in an Adobe AIR application nothing works.
My question:
Do Adobe Palettepanel and Air work together?
Thanks,
Alois Blaimer

I'll say for the moment no it doesn't, it has been requested and
probably in the future it'll work with AIR.
Sincerely,
Michael
El 11/05/2009, a las 2:05, alois2805 <[email protected]> escribió:
>
Hallo!
>
when I am working with Flex and the Adobe Flash Player everything is
fine. I even can use the Adobe Paltettepanel to integrate my Flex
applications in Adobe Indesign.
>
But when I want to use the Palletepanel in an Adobe AIR application
nothing works.
>
My question:
Do Adobe Palettepanel and Air work together?
>
Thanks,
Alois Blaimer
>

Do Palettepanel and Adobe Air work together?

Hallo!
when I am working with Flex and the Adobe Flash Player everything is fine. I even can use the Adobe Paltettepanel to integrate my Flex applications in Adobe Indesign.
But when I want to use the Palletepanel in an Adobe AIR application nothing works.
My question:
Do Adobe Palettepanel and Air work together?
Thanks,
Alois Blaimer

Hi Alois,
If I'm not mistaking than Patch Panel was designed for the Flex developers and I don't think it has support for AIR.
With best regards,
Barna Biro

Edege animate: Parallax and Spotlight = Not working together?...

Hi all,
This is my first post, and sorry for my English :))
I am learning, and have a small composition on Edge Animate CC 2014 on Scrolling Parallax, which works very well, and now I want to add a spotlight... but do not working together.
My code is:
Stage: 1920 x 2000
Autoplay: No
-- creationComplete: (nothing)
-- compositionReady:
EC.Parallax.setup(sym);
On scene:
A Text (is for launch the spotlight with the click function):
Action for "Text":
-- click
// Open image in spotlight overlay
// Set up configuration
var config = {
width: "1024",
height: "768",
type: "image",
source: "images/dog.jpg"
EC.Spotlight.open( config );
My problem is that the parallax works great, but when I make a click on the button that showing the spotlight... this is not released, and "dog.jpg" picture it is show on the bottom of the page (without spotlight).
What am I doing wrong?
Note: I charge via url the "All in One" of EdgeCommons CDN : http://cdn.edgecommons.org/an/1.1.2/js/min/EdgeCommons.js
Many thanks!

Ok. I've solved. I needed to load some things:
EC.Parallax.setup (sym);
The full code (that works for me) is:
-- compositionReady:
EC.Parallax.setup(sym);
// Load Edge Commons
yepnope({
load: [
"http://cdn.edgecommons.org/an/1.1.0/js/min/EdgeCommons.js",
// Load style sheet for the overlay
"http://cdn.edgecommons.org/an/1.1.0/css/style.css"
-- click
// Open image in spotlight overlay
// Set up configuration
var config = {
width: "1024",
height: "768",
type: "image",
source: "images/dog.jpg"
EC.Spotlight.open( config );
I hope to serve others.
Regards

Bridging wireless and wired network interfaces

Hi,
Is it possible to "bridge" the airport and ethernet network interfaces on a macbook pro using Leopard (10.5.7) ? I do not mean Internet connection sharing. That results in NAT.
I recently got a desktop in my room which doesn't have a WiFi interface. I wish to connect its wired interfaced to my mbp's wired interface and give it access to the wireless network my mbp is on. To do this I would need to bridge the wireless and wired interfaces on my mbp. All the results I find online to do this only talk about Internet Connection Sharing ..
thanks,
regards,
Puneet

You can turn on IP Forwarding to achieve most of what you're after:
sudo sysctl -w net.inet.ip.forwarding=1
This will have the Mac forward packets from one interface to the other without NAT.
However you still need to use separate subnets, and may need to play with routing to get everyone to talk to each other.

Can Forms 6i and Personal Oracle8i work together?

Hi,
I am going to download
1. Oracle Forms Developer/Server Release 6i for Windows NT
2. Oracle8i Personal Edition on NT
Before download them, I want to know if they can work together. I want to learn Oracle database and developer 2000. If you have a better idea, please let me know.
Thanks in advance.
Sue

Sue,
If you're going to download them from the net, then good luck - I never managed to do it. I now have CD's for all the Oracle products and have Personal Oracle 8i and Forms 6i on my NT pc. It all works fine. You won't have any problems (as long as you get the software on CD's). For the username/password, just use scott/tiger to start off with.
Harry
null

CS6. Need to have time remapping and warp stabilizer work together.

This should be obvious for most people. These two effects must be made to work together.
If you're shooting with a glider you're usually moving very carefully (read: slower than normal) so the footage in post would need to be sped up plus stabilized a bit.
Currently warp stabilizer and time remapping cannot be applied at the same time. But I *need* it to be applied at the same time. I need a workaround.
Should I:
1. shorten the clips, export them, re-import them into the project, and then apply stabilizer?
2. apply the stabilizer, export them, re-import them into the project, and then shorten them?
How do I export individual clips as just seperate clips while Premiere? Do I have to drag them into an empty timeline one by one, apply the stabilizer/remapping, and export, remove the clip, put in the second clip, etc all one by one?
I've used Mercalli in the past and I time remap the footage and then apply Mercalli to the accelerated clip. Mercalli doesn't mind a bit.

ComputerNovice25 wrote:
Adobe might have written the code in a way that doesn't include the ability to deal with that extra variable. I'm assuming that when it's nested it then makes the timeline it's in just read it as a normal clip again instead of a clip with a non-supported variable included.
Although I'm totally just guessing, but if what I'm saying is correct it would mean a fix wouldn't be very much work at all. Which means in the future they could simply provide a quick and easy patch to fix this. I'd highly suggest to make a feature request.
https://www.adobe.com/cfusion/mmform/index.cfm?name=wishform
Does Adobe read these feature requests? I often have a hard time justifying spending time to type out something when I feel like it's just being thrown into a black hole. I'm sure the team gets thousands of feature requests. It's like the lottery. Statistically you will never win. Sure, you'll never win if you don't play, but it's still a waste of time to play. I know, I'm pessimistic. Just don't have much faith in conglomerates - although Lightroom 3 is by far the most perfect program I have ever used and I would kiss the LR3 team if I could.
With Lightroom, Photoshop is hardly needed anymore unless absolutely necessary or for truly intensive chop-like edits. Premiere DESPERATELY needs a Lightroom equivalent.
I have half a mind to guess (nicely) that you video guys have absolutely no idea what you're missing out on, workflow-wise. It's life-changing. Literally.
I'm doing a video right now and I can't stop thinking about how if I had a Lightroom workflow, this video consisting of 40 clips, 40 titles, 40 transitions, audio tracks could be on the way to final export in 5 minutes. 5 MINUTES. And be 100% as good as if I had to spend an hour doing this in traditional Premiere.

Wireless and cable network working together

Similar Messages

Maybe you are looking for