Wireless and Ethernet connection for U330 not working - Help

I need help with my wireless and ethernet connection for the U330 notebook. I can not connect to the internet since I received my U330 and if I try to connect to a wireless router, it knocks other users off. I called customer service already and they asked me to download the driver on the Lenovo Downloads and Drivers page. The page can not be found when you try to download the drive so I was not sure if there is another place I can download it since customer service mentioned that they will send me a disk which will take some time. Thanks in advance.

Your router may be knocking you due to lots of facts. Those Ensteins suggested drivers reinstall because that's the only thing they know.
Try changing your encryption mode, try adding your laptop's WiFi MAC-adress of whitelist of Route, try disabling firewall, try increase strength of signal.
Driver is located at consumersupport.lenovo.com - do not hesitate to check.
//help will save the world

Similar Messages

Ok i literally just took my ipod 5 out of the box and the home button is not working help me pleasee!

ok i literally just took my ipod 5 out of the box and the home button is not working help me pleasee!

I would go straight back to store, state the problem and ask for a replacement. Good luck.

Just bought iworks and the serial number is not working. help!

just bought iworks and the serial number is not working. help

How did you buy iWork (no 's', capital 'W')?
If you downloaded the trial version earlier, and have since purchased a serial number, iWork will ask you for the number the first time you launch one of the iWork applications after the trial period ends.
If you bought a retail box, or bought the individual applications through the Mac app store, no serial number is needed, but if any part of the trial version is still installed on your computer, you'll get a request to enter a serial number before proceeding.
In the last case, you must delete all traces of iWork and it's applications (but not the documents that you have created and saved), then reinstall the purchased versions from the DVD or from the app store.
For the simplest and most efficient means of deleting the trial version, go to Yvan Koenig's iDisk, then to:
for_iWork > iWork 09 > uninstall iWork 09.zip
Unzip the file, open with Script Editor and run.
Regards,
Barry

Internet won't work with wireless and ethernet connected at the same time. Airport extreme

Why can I not connect ot the internet when both the ethernet cable is connected. The connection is fine when only on wireless and fine when only the ethernet cable is connected but won't work when the cable is plugged in.
any ideas?

opps forgot to set router as bridge turned off NAT and problems solved

NW04s JDBC Connection for MSSQL not working

In portal JDBC settings are:
Connection properties
URL = jdbc:microsoft:sqlserver://192.168.0.101:1433;DatabaseName=Northwind
Driver = com.microsoft.jdbc.sqlserver.SqlServerDriver
User Management
User mapping type = admin,user
I assigned a user to Administrator under User Administration
Visual Administrator settings are:
DriverName = com.microsoft.jdbc.sqlserver.SqlServerDriver
URL = jdbc:microsoft:sqlserver://192.168.0.101:1433;DatabaseName=Northwind
UserName = empty
Password = empty
Result
Connection test fails in portal. The settings appear ok.
The only thing I can think of is that user specified in portal user mapping is not setup properly on SQLServer.
Also:
When I run link:
http://localhost:53000/TestJDBC_Web/TestJDBCPage.jsp
my jdbc service MSSQL_JDBC does not appear. MSSQL_JDBC was cloned from SDK_JDBC and the libray for drivers was added
I am running MSSQL 2000 SP4 but using JDBC drivers for SP3 as I didn't find any for SP4 and assumed they would work for SP4
What am I missing?

Raynald,
I think I am having a similar problem.
I also cloned the connection names in Vis. Administrator to the SDK_name.
Indeed it now appears in the test servlet, and I can succesfully execute SQL statements from there.
So the connector seems ok.
But I have still problems with the Connection Test in the Portal.
I am trying to make BI JDBC system to be able to use my database from the Visual Composer.
I am using these properties:
CodeLink = com.sap.portal.systems.bi.SAP_BI_JDBC
ConnectionFactoryClass = SDK_TESTDB
ConnectionUrl = jdbc:jtds:sqlserver://sapserver:1433;databaseName=TestDb
(this url is the same as in Vis. Administrator)
Driver Class Name = net.sourceforge.jtds.jdbc.Driver
Fixed Catalog = empty
Fixed Schema = empty
System Type = SAP_BI_JDBC
User Mapping = admin, user
I am logged in as Administrator, so I added the login credentials at the User Mapping page of the Administrator user.
When I use Connection Test function from the portal I get the following messages:
Retrieval of default alias successful
Connection failed. Make sure user mapping is set correctly and all connection properties are correct.
What can I do to solve this problem?

Push and banner notification for Email not working on Iphone 6

Just got my iPhone 6 on Friday and I have my email set up to Push emails but that isn't happening. I'm getting them much later then they actually come to me and I'm not getting the banner on my phone when it does finally make it to my phone. I have all the setting correct that I can tell. I have it set up to notify me when email comes in via banner. Set up to notify me in lock screen as well. Does anyone know if I'm missing a setting? I notice now on this new system that in email set up I use to just have the Push option but now under Fetch - Push there is each mailbox listed and within them it says Fetch --- but I want Push not fetch......

I have been having the same email problem for hours and my Iphone email is also not working. Unable to log into Verizon webmail as well. I was finally able to get into my email account via Yahoo mail (yahoo/verizon accts linked). Still having issues with Outlook and my iPhone.

Ethernet connection to Internet not working

I have a mac mini (pre wireless) connected to a siemens gigaset se587 wlan DSL router via Ethernet cable. This worked fine when I set it up a couple of weeks ago. Now the mac mini has stopped connecting to the Internet. The router is working: I can still connect to Internet wirelessly on my iPhone and can still run airtunes on an Airport express from the iPhone remote app.
My ISP (tiscali) don't support mac and have been useless. Apple support also can't work it out.
I've reset countless times and tried setting up a new connection and the mac can recognize the router it just won't open any web pages!
Please help - I'm tearing my hair out!

This could be a DNS server issue.
Following the suggestion in this post (thanks AndyO!) to enter an IP number directly would give us more info:
http://discussions.apple.com/thread.jspa?messageID=6151522&#6151522
If it is a DNS server issue, then switching to DNS server like OpenDNS might help resolve it:
https://www.opendns.com/start
though there are some countries where OpenDNS is not available.

I upgraded from 10.3 and now "Connect to Server" not working!

yesterday I upgraded my co-worker's computer from 10.3 to 10.4, and for some reason he can connect to the internet but he can't connect to our server. We ususallly go to "Go to Server," type in our server address and then that window will go away and a new window will pop up showing that it is searching for that address. However, when I click on "Connect" the window remains and nothing happens. Thus we cannot connect him to the server, although he is able to connect to the internet with no problem.
Any suggestions?

what about trashing the finder preferences? did you try that first? I was thinking of trying that....

I updated my mac os x mountain lion to v10.8.5 and my internal speakers and even connected earphones are not working. Please help

i updated my OS on macbook pro 13inch from mountain lion v10.8.4 to mountain lion v10.8.5 and when i played songs on itunes there was no sound from the speakers, when i plugged in my earphones there was still no sound. i restarted my mac a few times but still it did not help. I need to get my speakers started soon. Please help

Have you tried a PRAM reset?
http://support.apple.com/kb/ht1379
Ciao.

Error 11333? Check for updates not working, help please...

I got the message 11333 when I tried to open iTunes for the first time, so I checked for updates. But when I "check for updates" in iTunes, it tells me that "server could not be contacted, check your internet connections and try again". I am connected to the internet and I'm able to surf the web, so what's going on? I'm working with a PowerPC G5 with a dual processor. Version 10.5.8

Already answered in your duplicate thread:
https://discussions.apple.com/message/19062041#19062041
Please do not double post the same question.

HT4108 Hello I really need someones help I bought the composite AV cable from the apple store to plug my ipad to my dvd player in my excursion to play movies and the video line is not working help

Hello out there, is there someone that has a solution to my problem? I have an Excursion and it has the red,yellow,and white aux outlet and I went to the Apple store and bought the composite AV cable plugged it in and the audio works but the video does not and the manual says that I have to tell the ipad to send the video to the t.v.,projector but I can not find where that function on the ipad. Please help despirate mother of four.

On ipad screen during playback, look for an icon that is a rectangle with a triangle in it.
press it,should see a list of available devices.

Creating and using a digital signature - Not Working / Help Please?

I have Acrobat X Pro (10.1.11). I am trying to setup a digital signature that is either a scan of my own signature, or a digital version that looks like hand writing. I've gone through a number of help documents and I am still getting something different. What I get is a Printed Name with some text next to it (i.e. Digitally Signed by "my name" DN: cn="my name, o, ou, e-mail, etc.".
Anyone have any idea how I can start from scratch and create a digital signature that I can simply place on PDFs that looks like my siggy?

I believe you are confusing digital signature and digital signature appearance. You can create a custom appearance and use it in your signatures. Go to Edit->Preferences->Signatures->Creation & Appearances->More... In the Appearances section in the bottom portion of the dialog select "New" button. Configure Signature Appearance dialog comes up. In the Title field you enter the name of this appearance. In the Configure Text section of the dialog you check which values you want to have in the text part of the signature appearance (you can deselect them all). In the Configure Graphics section you can select one of the radio buttons. "Imported Graphics" allows you to browse to the file that contains your scanned signature (or your picture ). "Name" will place your name as it appears in your signing certificate.
Then when you sign a PDF in the "Sign" dialog click on the down arrow in the Appearance: section next to the displayed appearance name (out-of-the-box is says "Standard Text") and you'll get a drop-down list that contains the name of the appearance that you created. Select it and that will be the appearance of your digital signature. This same drop-down list contains "Create New Appearance..." item which when you select it allows you to create a new appearance in the same way as I described in the first paragraph.
After you select your appearance it will show up when you sign again.

Wireless and Ethernet Network Do Not Work Other Than SpeedTest

I have been having major problems with my Mac's Internet. Whenever I connect to my Wireless or Ethernet Connection, the signal start out strong and dies down to almost nothing (around .4 kbps) immediatly. I have been having this problem for a couple of weeks now. However, when I run SpeedTest.net, I get the connection speeds which I should be getting. My Network Application thingy (iStat Menus) shows a major increase from .4kbps to 6MBps when the speedtest in running. Any ideas on how I can fix this problem?

It's a router all right. The next question is what is the "downstairs" device? Router or...?
The Aliant is configured through a browser interface and its IP address ought to be 192.168.2.1. Put those numbers in Safari's URL field and see if its webpage loads. If it does, you might be able to find a setting called "bridge mode".
Beware that I'm way out in the weeds with this suggestion - changing things in that unit may cause you even more problems. Since you said it is connected to a "wall Ethernet plug" I'm concluding that it should not be acting as a router, but that depends on what is upstream of that wall plug, and what functions the downstairs device is performing.
If the "wall Ethernet plug" is in fact a phone line and not an Ethernet LAN port then it is your router and you won't want to change that.

Hi, My Lightroom CC is showing waiting for connection and the mobile sync is not working. I have tried deleteing lrsync data, disabling firewall, checked host file etc. Still no luck.

Hi, My Lightroom CC is showing waiting for connection and the mobile sync is not working. I have tried deleteing lrsync data, disabling firewall, checked host file etc. Still no luck.

I had the same problem. It fixed itself when I opened Internet Explorer (I don't normally use it). I was opening Support Portal to get some support help, but I'm not sure if it was the page or simply opening IE that did the trick.

I have iphone 4s and just bought an ebook for ibook, trouble is the font is so tiny I can't read it and the font sizer is not working? Please help!

Hi, I have the iphone 4s and just bought an ebook for ibook, trouble is the font is so tiny I can't read it and the font sizer is not working? Please help!

Hello Glittergirl68,
Thank you for using Apple Support Communities.
It sounds like the function to reseize the Font in an iBook is not functioning properly.
I recommend a few things here. First close all the apps that are running in the background:
Double-click the Home button.
Swipe left or right until you have located the app you wish to close.
Swipe the app up to close it.
From: iOS: Force an app to close
http://support.apple.com/kb/ht5137
When you have done that, restart the phone, and try again.
If the issue persists, I would follow these steps from the article:
iOS: Troubleshooting apps purchased from the App Store
http://support.apple.com/kb/TS1702
2. Check for app updates
You can setup apps to update automatically in Settings > iTunes & App Store, but make sure that your apps are up to date:
Open the App Store and tap Updates. If updates are available, tap Update All.
If prompted, enter your iTunes Store account information. App Store will then download and install the app updates.
Note: Some apps may require a Wi-Fi connection to update.
3. Install another app from the App Store
If none of your user-installed apps will launch, there could be an issue with Apple ID authorization. Download and install an app that isn't already installed on your device to reset this information. You can also remove an app from your iOS device and download it again from the App Store or sync the app from your computer.Note: If you have installed apps using multiple Apple ID accounts, you may need to perform this step for each account.
4. Restart the app
If the issue affects only a single app, try closing just that app.
5. Restart your device
Turn the device off and on.
6. Reinstall the affected app
Remove the app from your device and reinstall it:
Tap and hold any app icon on the Home Screen until the icons start to wiggle and show a small "x" in the top-right corner of the app.
Tap the "x" in the corner of the app you want to delete.
Tap Delete to remove the app and all of its data from your device.
Press the Home button.
Go to the App Store.
Search for the app and then download it again.
All the very best,
Sterling

Wireless and Ethernet connection for U330 not working - Help

Similar Messages

Maybe you are looking for