Wireless B router woes after firmware upgrade

I downloaded and installed the firmware upgrade for my wireless B ver.4 router and now it's not transmitting a wireless signal. Computers plugged into the wireless router get internet connection, but it doesn't seem that the the router is broadcasting wireless. I tried to go to my routers set-up by using the default router IP...but it won't connect...any thoughts?

Since you have upgraded the firmware on your Router, You need to Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

Similar Messages

  • HP 5524 Wireless does not work after firmware upgrade

    HI,
    I have just purchased an HP5524.  After initial problems setting up the WPA key from the printer screen, I connected via USB, found the printer and swapped to wireless successfuly. I then installed the printer software on all my computers at home successfully over wireless.
    The printer then needed a firmware upgrade to support eprint (?), which is successfully connected, downloaded the fireware, installed and went through the boot cycles successfully. 
    However, ever since wireless will not work.  Before I return it to the retailer as "not fit for purpose" I thought I would ask the forum.  The diagnostics downloaded a tool, which I went through, but this did not offer solutions that I had not already tried.
    Thank you

    Hi,
    Thank you for posting you query,
    In order to resolve the issue, please make sure the printer is placed closer to the router and uninstall the printer drivers already installed and then start the instalaltion and seelct teh connection type as wireless network. Then select use USB to configure wireless and when prompted conenct the USB cable and then select the network and enter the encryption key follow the onscreen  instructions.
    If the issue still persisits, please open the browser and in the address bar enter the IP address of the router and click on GO. This will take you to the router configuration page. On the router page, please click on Wireless Setup  and please make sure SSID Broadcast is enabeld and the Wireless Mode is set to Mixed or 802.11 B/G/N and the Wireless Channel is set to 11 and click on Apply. Then try to connect the printer to the network by using the CD.
    Say "Thanks" by clicking the Kudos Star in the post that helped you.
    Please mark the post that solves your problem as "Accepted Solution"
    (Although I am employed by HP, I am speaking for myself and not for HP)

  • Crippled 192.168.1.1 page after firmware upgrade

    hi,
    i recently upgraded the firmware of my WRT160N V2 to 2.0.03.
    but since then when i login i get a crippled page on 192.168.1.1 with not even a menu. so i cant even downgrade. is there something i can do?

    It is good to know that the issue is resolved
    After firmware upgrade it is always recommended to reset and reconfigure the router and I think that is why you were unable to see the menu on the setup page of your router.

  • PC-Suite sync fails after Firmware upgrade of E65

    After firmware upgrade of E65 PC-Suite stops syncing Calendar & Contacts from outlook. No error messages, just "0 entries has been updated".
    - PC-Suite updated to 7.0.9.2
    - Outlook 2003
    - XP Prof.
    Any ideas?
    Solved!
    Go to Solution.

    The funny thing is - the notes are synced???? If I restore some old contacts they'll double up in outlook, so I think the problem is, that the sync app doesn't see the outlook contact & calendar folder.
    Does somebody has an idea?

  • T410i SSD user and master password problem after firmware upgrade

    Hello.
    I have problem with my Corsair Force 3 120GB SSD. After firmware upgrade of SSD my master and user HDD passwords are no longer valid. I'm stuck on BIOS screen and cannot unlock my SSD. After firmware upgrade procedure i got BSOD. Same happened during firmware upgrade on my previous SSD (INTEL X25-M 80GB) but after restart everything was OK. Please help!
    Previous firmware version: 1.3
    Current firmware version: 1.3.3
    SSD connected to another computer shows RAW partition data, but firmware version is 1.3.3 - seems like update was successful.

    My X301 Intel x18 got bricked also after a BIOS update then secure erase (was going to sell it). I plugged it to a USB kit and onto a desktop and it was recognised and able to format. But plugging it back to the lenovo it is still a brick. My lucky star there was warranty it was replaced by lenovo.
    You may want to try it and extract the data, if it works. And hopefully you can still format it and made it work pluggin back to the lenovo.

  • SB wow wireless not working after firmware upgrade

    Hello,
    In the beginning of this year I bougth a pair of Sound Blaster World of warcraft wireless headset. And there have been alot of trouble with them, I've been using the latest software but not the latest firmware ever since then.
    And every now and then my mic stop to work, I could hear sound but the mic was totally dead, and all of a sudden, of no logical reason the mic started to work agian.
    So I thought a firmware upgrade could make them work better, but no, i upgrade firmware from .9.x to .0.x.
    And guess what happens? Nothing works no, not the sound, not the mic, the USB trasmitter cant even sync with the headset anymore.
    Ive tried a million things now, some of them are:
    . Just tried to reinstall it, didnt work
    2. Tried to install it in winxpsp3 compability mode, didnt work.
    3. Tried to clear all temp-folder (the temp-folder under c:\windows\temp and the user-temp) after Ive uninstalled it, didnt work.
    Im running on Windows 7 Professional x64 edition.
    What could cause this? I havnt tried to install them on a XP-computer yet tho. But I have to get them work in Win7, since i cant downgrade just because of a headset, huh?
    Thanks,
    Johan

    Ok, please redirect me to a tecnical supportpage where I can find potential solutions,
    - and instructions how I do for example a downgrade of firmware?
    PS, This page does not include any potential solution:
    http://support.creative.com/Products...tDetails.aspx?
    catID=437&CatName=Headphones+%26+Headsets&subCatID =23&subCatName=MIDI+Keyboards&prodID=9068&prodName =Sound+Blaster+World+of+Warcraft+Wireless+Headset& bTopTwenty=&VARSET=prodfaqRODFAQ_9068,VARSET=CategoryID:437

  • RE1000 Will Not Connect to WLAN after firmware upgrade

    I upgraded the firmware on my RE1000 to v1.0.02 a few days ago; now, the RE1000 will not connect to my WLAN.  The automatic CD program is useless; it won't see my WLAN.  Manual configuration goes slightly better, but still no luck.  If I try to connect via Wireless --> Site Survey, it sees the SSID (and a few others in range) and says it's connecting, but when I go to Status --> WLAN Statistics the status of the link is shown as down (router also confirms no DHCP lease given out).  When I try to configure the connection manually via Wireless --> Basic Wireless Settings, same results -- link down.
    I've tried configuring a static IP (vice DHCP) but no change in result.  One odd thing I've noticed is that in the WLAN Statistics page, "Wi-Fi Protected Setup" is still showing as "On" despite it being set to off.  Not sure if that has anything to do with it, but either way this is getting wretchedly annoying...

    I am trying to set up a LInksys RE-1000 for a user who has a working Linksys WRT-54G wireless router which is working perfectly fine both wirelessly and wired. This RE-1000 product was purchased after checking the RE-1000 owner's manual PDF download which confirms it is supposed to work with Wireless-N, G and B though with slower speeds with G and B.
    However, the RE-1000 does not connect to the WRT-54G at all using manual configuration with a network cable connected to the RE-1000. After entering all the correct parameters under the WIRELESS - BASIC WIRELESS SETTINGS page that matches the WRT-54G wireless security settings fully, the RE-1000's STATUS - WLAN STATISTICS page simply continues to show that the RE-1000 is "CONNECTING..." but never goes to CONNECTED status. Checking the RE-1000's STATUS - DEVICE INFO page shows that IP address, subnet mask and default gateway are all 0.0.0.0, which seems to confirm there is no successful connection between the RE-1000 and the WRT-54G via wireless-G band.
    The firmware on the RE-1000 is already 1.0.02 from factory. Calling Linksys phone support was useless because the phone agent in the Philippines simply gave pre-scripted generic suggestions such as upgrading the firmware on the RE-1000 and the WRT-54G, when the WRT-54G's firmware was already updated to the latest available version.
    Can anyone from confirm whether the RE-1000 is capable of connecting to the WRT-54G wirelessly? Or does the RE-1000 require specific wireless routers to connect successfully with? I did not notice that the product / system requirements stated anything about this.
    My experience so far with the RE-1000 wireless extender product has been unsatisfactory so far and I am an advanced user with the Linksys router.

  • BEFW11S4 constant disconnect after firmware upgrade

    I was having trouble with my router losing connection every 2 hours or so . I have downloaded and installed the latest firmware and now it keeps disconnecting almost every 30 min. I have a static IP on my main pc and dhcp enabled for my xbox360. I have checked the cables if they were bad by swapping them but the problem was still there. Any help would be very much appreciated.

    After a firmware upgrade, you must reset the router to factory defaults, then setup the router again from scratch.  If you saved a router configuration file, DO NOT use it.
    Also, please list all the static LAN IP addresses that you are using on your network.
    If you are not using the default DHCP server range of 192.168.1.100  thru  192.168.1.149 , then please state your DHCP server range.
    Are you running any peer-to-peer (P2P) software?  If so, this is a known cause for router slow downs and disconnections.  Temporarily stop using the P2P software, then reboot router, and see if this corrects your problem.
    Who is your ISP?  Are you on a cable system?  Some cable systems monitor the MAC address of the devices connected to them, and eventually boot off any MAC address they don't recognize.  If you are on a cable modem, try cloning your MAC address (done in the router), and see if this corrects the problem.

  • Wrvs4400n not stable after firmware upgrade help!!

    Hi,
    I need some help.
    System:
    WRVS4400N wireless router
    Firmware 1.1.03
    IPS:  1.31
    I went through LinkSys site and downloaded the new firmware and ips signature listed above.  I upgraded my system a few days ago and having alot of problems with disconnection through the router.  I would have to reset my wireless router every so often since the firmware upgrade.  Most of the time, it would take one tries but sometime i would have to unplug and plug the router's power cable many times before having internet access.  My previous firmware version i believe is 1.0.06 and it was working fine except that my MAC OS X wasn't able to connect via wireless connection.  That's why i decided to proceed with the firmware upgrade.  Now, the new firmware is giving me a whole new problem and unfortunely i forgot to back up my previous system's config (firmware).
    I am sure this problem is not caused by my IPS or the modem because when the connections get dropped, i was able to connect directly through the modem.  I am not sure if others are experiencing the same problem, but at this point, i think this is some bug on the new firmware.  Please i need some solution to this.  Any advice or suggestions?
    Thanks

    There is a Recovery program for recovering from the latest firmware "upgrade" that borks the router. The latest "firmware "upgrade" completely trashed my router. I could not even connect to it from its internal IP (192.168.1.1) to attempt to downgrade the firmware. Nice of Linksys to allow people to go through an upgrade that trashes their router. Then to make matters worse, the Receovery program only works in windoze, so I had to find a windoze machine to use to downgrade the firmware. What happens if you run Linux - out of luck. Long story short, why not have some kind of warning on the firmware upgrade that unless you first do the recovery firmware flash, you can kiss you router goodbye for the time being.

  • No power after firmware upgrade on nomad jukebox zen xtra

    I have the nomad jukebox zen xtra 30gig that froze up over a year ago after i tried to install the firmware upgrade. After the unsuccessful attempt, the mp3 player stopped working.... I mean no power at all. I've changed the battery and recharged the battery from an outside source...still no luck. I can't even try any of the suggestions anyone gives on this site because I have no power.Does anyone have this problem? More important, does anyone have this problem and know of a solution?I've already set my pc back to wmp 0, I have the firmware on the desktop waiting. Now all I need is some power on this unit so that i can try some of the suggestions that seems to be working for people. Thank you

    I have the same problem too, but my unit is a?Creative Normad Junebox Zen Xtra 40GB. I was trying to find a solution to my problem when I read about your problem. I have pressed the reset button, on / off switch, removed the battery, reinstalled the battery, and nothing seems to work. I was hoping you?might get a solution to this problem, so that I might be able to fix my MP3 player. If I hear of a solution, I will let you know, thanks for sharing. Issue:? While updating the firmware to the Zen Xtra 40 GB, the unit powered down and?has never came on again. There seems to be no real reason why the unit should not power up. The battery and the AC adapter are working correctly. I am very disappointed in Creative...

  • No contacs after firmware upgrade on N70

    Hi
    I did a firmware upgrade yesterday on my N70 using NSU. Of course I did a backup using the uptodate Nokia PC suite. After the firmware upgrade I saved the data back to the phone aagin using the Nokia PC suite. Everything looks good except that no contacts are there.
    I did the upgrade again just to make sure that everything went OK with the same result.
    Can some help or has the same problem?
    Firmware V 5.0638.3.0.1 18-09-06 RM-84
    PC Windows XP SP2
    Nokia PC Suite 6.82.22.0
    NSU 1.2.0en
    Best regards
    Chris

    not sure about your PC Suite version but this has been well documented in these forums and I had the same problem and with N70. I think it was mentioned as a PC Suite issue, or a combined PC Suite issue N70 issue with many people reporting it. Anyway nothing you can do but enter your contacts or transfer from another phone

  • HP Laserjet p1102w - after firmware upgrade / Smart Install update - down to 1MB free memory

    Hello,
    I have a Laserjet p1102w running off a laptop with Windows 7 64-bit. Just bought the printer this month.
    After updating the firmware to 20120814 version and updating the SmartInstall update utility for the 20120814 version as well, I am now down to 1 MB free memory (out of 8MB originally). [Another LJ p1102w updated prior to these updates has 3MB free memory.]
    Because I have 1MB free memory, the printer is almost a brick. It can print simple text based pages - however, printing any page with a graphic or a PDF file will cause the printer to take forever to receive data - essentially preventing printing a page on  my new printer (while printing the same page instantaneously on my older nonupdated p1102w).
    Is there any way to fix this problem, given there is no memory upgrade option? Otherwise, this printer is a brick.
    Thank you in advance for a reply - especially from HP.

    Hi cyskim,
    Did you tried turning the printer off and on after updating the firmware? This should clear its memory, including any memory may affected during the firmware upgrade proccess .
    Say thanks by clicking the Kudos thumb up in the post.
    If my post resolve your problem please mark it as an Accepted Solution

  • Fans And Voume after FirmWare Upgrade

    Hey there!
    I have two very positive pieces of information, some repeated:
    1) The volume of my speakers and "line out" was weak at best prior to the FirmWare upgrade. Now, it is positively explosive! I mean, the volume control works just like I would have expected. Perfect...
    2) The fans are coming on more consitantly. I can actually hear them now, which makes me wonder... The temp on the Hard Drive has not gone above 92 since I upgrade the firmware (not that I have noticed however).
    Bob

    Hi Bob!
    What did you use to check the temperature?
    I installed the 10.4.6 and the firmware, and now I could cook an egg on the keyboard. I didn't have the heat problem before, now after the updates, I am fried (literally).
    Gus

  • Iomega Storcenter ix4-300d stuck at 95% after firmware upgrade

    Hi,
    I upgraded my device after I got an email that there is a new firmware:
    An update to version 3.2.10.30101 of the Iomega StorCenter ix4-200d software is now available
    I installed the update but now it is stuck at 95% after rebooting.
    Never had any problem before the firmware upgrade. 
    Any advice?

    Hello BelgianTomas
    I recommend that you first power down the unit if the unit has not completed the boot process.  Then re-seat all disks and try booting the unit again.  Please do not try to access the web interface until the power led is solid white.
    Next would be to try moving the internal disks to different bays to see if a different drive order wil allow the unit to boot. 
    If that does not help, LenovoEMC suppor should be contacted for more advanced options.
    LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
    US and Canada: https://lenovo-na-en.custhelp.com/
    Latin America and Mexico: https://lenovo-la-es.custhelp.com/
    EU: https://lenovo-eu-en.custhelp.com/
    India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
    http://support.lenovoemc.com/

  • Content Copier wont restore after firmware upgrade

    I upgraded my N95 8GB to the latest firmware this morning (30.0.018), took 2 complete backups using Contect Copier V4 prior to doing so, but after the upgrade every attempt to restore contacts, settings, etc has failed.
    I've tried doing the recommended re-formatting procedure, followed by a restore, which did not help. I've tried restoring individual items only, instead of the whole lot, which also didn't work.
    According to the log at the end of the restore, the restore completed successfully. Reality suggests otherwise though.
    Could anyone please help?
    Thanks,
    Adriaan

    Right, I've tried using OVI, which did NOT resolve the problem. In fact, it gave identical results to the content copier included with the nseries suite.
    I've written to Nokia support who have replied as follows:
    "In this instance, allow me to suggest a few workarounds in order to rectify the issue on hand.
    First, I suggest that you delete any data not needed from your Nokia N95 8GB to free up the internal memory of your phone before restoring the backed up file. I would like to also suggest that you select the content files that you want to restore to the Nokia N95 8GB. Once you have connected your Nokia N95 8GB to the PC and launched the "Content Copier" application, please select the content file types that you want restored on the phone.
    However, if you are still unable to restore the backed up file to your Nokia N95 8GB, there may be inherent issues with your Nokia N95 8GB that may prevent you doing so. In this case, please take your phone to your nearest Nokia Care Point for an assessment. The Nokia Care Point will assess if a repair is required and advise if this may be covered under warranty."
    So it looks as if I'm going to have to take it in for repair...

Maybe you are looking for