Wireless Charger Status Light

The manual states that the light is supposed to turn off when the device is fully charged. So far, my light on the charging stand has not turned itself off. Has anyone experienced differently?

Seems to be working after a few remove / replace tries

Similar Messages

  • So i connected my ipod shuffle to my apple computer and the status light on my ipod shuffle shows that it is charging but when i look for it on the pc dock or in itunes it doesn't show it at all.... so what do I do???

    so i connected my ipod shuffle to my apple computer and the status light on my ipod shuffle shows that it is charging but when i look for it on the pc dock or in itunes it doesn't show it at all.... so what do I do???

    If you have not already, I would shut down (power off) your computer.  Do this to Reset your shuffle
    http://support.apple.com/kb/HT1655
    Start up computer.  Run iTunes.  Connect shuffle.
    If you have added a new USB device recently (since the last time it worked properly), you may want to try disconnecting it to see if that makes any difference.

  • My ipod 2nd generation won't charge.  No status light when conected to computer.

    Recently found an ipod shuffle 2nd generation.  When I tried to charge it there was no status light on it at all.  Thinking it could be beyond use as it hadn't been used for a long time.  Any advice welcome.

    Are you using the USB docking cable that came with your 2nd gen iPod?  It has a mini-dock at the iPod end.  The docking cable for the 3rd and 4th gen shuffle does not work with the 2nd gen shuffle, because the connector is different.
    If you are using the original cable (or a compatible third-party replacement), there are three possibilities.  (1) A problem with the computer's USB port not working or supplying sufficient power.  (2) A faulty docking cable, even if it's the right cable.  (3) A problem on the shuffle.
    If you can do some tests to rule out (1) and (2), then it is likely to be (3).

  • My computer and phone both can not find the airport wireless connection even though the status light is green whats going on?

    I have cox as my internet provider and the last couple weeks i have been having a ton of connection problems. The status light on my airport express is green but my computer is saying the connection is timing out and my phone is having issues connecting to the internet even though it says it is still connected to my wireless network. is it my airport express or something else?

    Manually mount the TC in the computer..
    In finder use Go/Connect to server.
    Type in the name of the TC or its IP address.. I recommend you use all names of SMB standard.. short no spaces and pure alphanumeric. That will give you much less trouble.
    So AFP://TCname.local (where you use the TCname replaced with the actual network name of the TC. local is the domain by default.
    You can use alternative AFP://TCIPaddress like AFP://10.0.1.1 (default IP of TC as router). This is only useful when the TC has a static IP.
    Make sure ipv6 is set to link-local in all the network adapters in the computer and the TC.
    Then go to TM preferences and you should see the TC listed as a possible target for TM.
    Read Pondini for other issues.
    http://pondini.org/TM/Troubleshooting.html
    eg C9 about long names.
    A1 to get log info from TM
    A4 to reset the TM setup.

  • The battery status light on my N200

    The battery status LED, on my N200 is ALWAYS on, its on even if it is running from batteries, or if it is on AC power, even if its fully charged the status light stays on..
    is this normal? its a status light....so it should not be "always" ON, right?
    Our sweetest songs tell of saddest thought

    Ok, you are not resetting the TC.. that is just restarting it. Resetting means to hold in the reset button or use the utility to reset it.
    When you say it goes dark, you mean it is not lit at all??
    Do any errors show up in the airport utility?
    I would say the TC is faulty but it maybe just a very minor issue if the wireless and backup is working.
    I would recommend a full factory reset.
    Unplug the TC power cord.
    Hold in the reset button and keep holding it in whilst you power the TC on.. it is helpful to have a friend (unless you have 3 arms).
    Keep holding in reset without release for about 10sec after power on, until the front LED flashes rapidly.
    Release reset and now redo the setup of the TC.. this will not harm any info on the hard disk but will reset the TC to factory and you will need to redo the setup.
    I recommend this time around use all names that are short, no spaces and pure alphanumeric.. Apple names have issues even with apple products.. see C9 here. http://pondini.org/TM/Troubleshooting.html
    Once you have it setup again.. does the front LED now go green.. if not you might still have issues with the utility .. clear or ignore them.. what happens now??

  • My airport time capsule did not set up successfully, and then status light flash amber

    Hi, Guys
      I am the first time user of the time capsule, please help how to proceed?
      I have set up the first time and my airport time capsule does not set successfully, then I try to reset to factory setting. After this, although I use the ethenet cable to connect the router to the airport, the status light flash amber, always, even after the reset.
      Also, I can see that airport time capsule base station from the wireless network when airport is plugged in. However, when I want to access to it.

    Thanks for your guidance, but the product is really anoying. First, I am sure that the airpor utilities is 6.3.
    and I also follow your instruction that to set the IPv6 as local link mode. But still get the same error as mentioned in my first post.
    Therefore, I have tried to use the bridge mode but could not find it, and therefore still can not set it up successfully, even though I reset the factory again(press the reset button 5 secconds at least).

  • Apple TV 3 Status Light turns ON and stays ON when I turn ON my Broadband Modem. How do I stop this ?

    Since I updated my Apple TV 3 to 5.1.1, the Status Light turns ON and stays ON when I turn ON my Broadband Modem. How do I stop this ?
    At the moment I have to go to the HDMI channel that my  ATV 3 is connected to, wake the ATV, then put it back to sleep, to turn OFF the status lght.
    When I first got my ATV I did not have this problem, when it was running 5.1.0.
    I sent in a Feedback form, but they only as the option to select the OS version of a NON iOS device.
    Is there a fix to this that wont involve me leaving my modem ON all the time ?
    I turn my modem OFF when I am not using the Internet because I am a bit paranoid about the security of the data on my devices, and if I leave the modem turned ON all the time it might make me an easier target for hackers etc. { This is NOT part of my question, just explaining why I turn my modem OFF ( I feel safer ) }
    <Edited by Host>

    The ATV3 does that to me when I turn on my TV. the light goes on and stays on. If I switch to the ATV3, it seems to be half asleep with the light on ... I do wish Apple would enable the HDMI CEC and then everything would make sense. I've turned off my wireless and on again but the ATV3 light does not turn on automatically for me.
    As you pointed out, I guess this could be a small glitch on the new firmware/software update... I wonder if this could be fixed by doing a restore from the iTunes app. I might give it a try tomorrow and see what happens...
    Cheers!

  • Apple TV loses picture output and status light flashes rapidly after 5 minutes hooked up via HDMI - DVI cable

    Apple TV connected to a 2005 50" plasma monitor with DVI input via belekin HDMI to DVI cable.  Unit worked perfectly long enough to get it connected to the wireless network and begin the itunes registration process when there was a loss of signal message on the screen from the monitor and the Apple TV status light flashed rapidly and continuously. Reset and reboot yeilded flashing rapid status light and no output detected from the monitor.  I contacted support online and was told to return the unit to the apple store.  I returned home with another brand new apple tv and connected it in the same manner with exactly the same results.  Is there something with the HDMI - DVI interface that is causing this?  Are there known issues with the HDMI - DVI connection to Apple TV with older plasma monitors?

    The Apple TV doesn't actually support DVI. Some have managed to get it to work others have had varying issues with it.

  • Nokia lumia 1520 with Nokia Wireless Charging Plat...

    I brought a nokia lumia 1520 and a wireless charger from AT&T. I tried to charge my phone when it had almost no power in it. But the white light kept blinking while I put my phone on it. And I'm sure that no other device between the two objects. Does anybody know what is going on with it?
    Solved!
    Go to Solution.

    The AT&T 1520 does not have Q1 wireless charging. This is what the DT-900 is.
    It has PMA wireless charging. AT&T had Nokia change the wireless chang platform to PMA, which is different than other Nokia phones.
    Complain to AT&T !     I did.

  • Status light in AP1130 doesn't work!!!!!

    I have a AP1130, it's working fine, except the status light is always green, even when there are clients connect to it through wireless in which case it should be blue.
    I've upgraded the firmware and the same problem still happens.
    Does anyone knows how to fix this??
    Thanks in advance,
    regards,
    Hugo

    Is it possible that you are actually connected to an adjacent LWAP? In other words, can you unplug the LWAP in question and still connect via wireless?
    The reason I ask is that there is a known issue where the 1131 LWAP turns status LED turns light green when it is not actually connected to the WLC.
    This behavior ocurrs when the LWAP is not receiving an IP address via DHCP.
    - John

  • Wireless charging plates not working

    Just received two wrieless charing plates. Despite of the fact that their power adapters are white while they are black (Would be nice if Nokia could match their colors, it isn't so hard and would look much better) none of them seem to be working.
    Tried both of them with two different Lumia 920s and nothing happens, no lights or anything. Is there anything I'm missing or did Nokia just sent two deffective units? I find it hard that I was that unlucky.
    Any help would be greatly appreciated.

    Hi there mate,
    Please check that you have placed the 920 in the correct area against the charger so that they charge. The area of the backside of the 920 that supports the Qi wireless charging is indicated in the user guide. If you have checked everything else, and it still isn't working, then you may have faulty chargers, or the phone's wireless charging function itself may be defective. It would pay to check with the retailer that you purchased the phone / charging plate with, to see if you can get it working in their shops

  • Wireless charging phone holder to be placed in car...

    Nokia please build a wireless charging phone holder to be placed in cars so that drivers can charge their phones while using navigation etc.

    Thanks Farby,
    @JianXingQuek
    Hi if you look http://www.brodit.com/ and put in the make and model of the the device you have they should have a passive or charging holder for your device which can fit in you car. The charging option comes with a cigarette lighter charger attached but there are also options from various engineers who can hardwire the charger cable so that it is hidden and the cigarette isn't obscured.
    If you find this post helpful, a click upon the white star at bottom would always be appreciated.
    If it also solves your problem, clicking ACCEPT AS SOLUTION below it will benefit other users!

  • Wireless charger?

    Is there a wireless charging pad available -- or in development -- for iPad 2 or Mini?  I just ordered one for iPhone 4 and it got me thinking how I hate hooking up the connector to charge this iPad 2 each night.  I rarely use the mini but would love to have a pad/mat that accepts both.

    Apple patents a lot of things.
    Most of them never see the light of day.
    Even if Apple releases something with wireless charging-it won't affect any product currently out.

  • DV6000 DC IN Jack lights up, Wireless shows orange light but no power! Help!

    DV6000 DC IN Jack lights up, Wireless shows orange light but no power! Help!
    I connect the AC adapter to the laptop and the blue light on the DC IN jack lights up, also the Wireless Card light shows up in orange color.
    No battery indicator, no power indicator would light.
    Can this fixed by just replacing the DC in USB Sub-board or what needs to be replaced?
    I have seen in ebay repair services for these known issues.

    yet looking in system diagnostics confirms that the
    adapter is connected, but not charging.
    Sorry, not system diagnostics, system
    profiler.
    PowerBook G4
      Mac OS X (10.4.3)  
    yet looking in system diagnostics confirms that the
    adapter is connected, but not charging.
    Sorry, not system diagnostics, system
    profiler.
    PowerBook G4
      Mac OS X (10.4.3)  
    Must be something magnetic in the ionsphere: mine has had the same symptoms. I was going to buy a new battery, but now maybe not. I think on mine the pmu module can be replace seperate from the logicboard? I was thinker perhaps the internal battery??? Really open to answers.

  • Lumia 920 Wireless Charging not working - Known is...

    I have a Nokia Lumia 920, which works perfectly fine. I haven't had some of the other issues reported here with freezing, apps, etc.
    I have a Nokia charging plate and I've found that no matter what I do the wireless charging plate absolutely does not work. I've turned off Bluetooth, Wifi, turned ON Battery Saver, disabled every background app, even hard reset my phone and tried charging it from stock. The wireless charging plate doesn't even maintain the current battery state - The battery slowly drains hour by hour. I've also tried placing the phone on the charging plate in different positions to ensure it's making good contact. Nothing works.
    Is this a known issue? Is there anyway to identify a defective phone? Is there a possible fix for this? I love my Lumia, but this a killer feature I would expect to work consistently.

    OK, this thread is odd. My charging plate works fine. It has a side with a little ring and Nokia in it, and the other side has an oval of rubber around the periphery with the usual conformance writing on it that side Qi, CE, don't throw it on the trash icon,  Mine works just fine with the Oval down, and the Nokia in the ring up. Is that not what others see?
    I can turn it over, but it is touchy as to whether I can get the light to come on. Usually not. I assumed, initially, the oval went down to keep it from sliding around on the table, and Nokia went up because they want you to know it's Nokia. Has always worked that way. I wish there was a larger rubber something on the 'top' as the phone can slide and spin more than I think it should.
    For what it is worth, I much prefer the charge stand, but the plate is more convenient if I am going to travel somewhere for a while. Couple of days, just charger, week or so, might bring the plate for the hotel.
    BTW, I do get the connect noise when putting it on the charge plate. Sometimes it can take a second otr two. When I take it off, it can take several seconds to get the disconnect noise and the charging icon to go away. If I put it back on the charger before the disconnect noise and the charge icon goes away, it does NOT make a connect noise, though the light comes on. The light will also eventually go off at full charge.

Maybe you are looking for