Wireless Connection between two routers

Ok. I own two houses seperated by a driveway going to both garages. I have cable internet access linked to a Netgear WNDR3300. That router is sending a signal to a wireless PC, 2 Laptops, and my Mini when needed. My signal in the 2nd house is REALLY weak.
I have a WRT54GS v4.0 sitting around and it to connect to the netgear and then resend a wireless signal to the wireless laptops around the 2nd house. can I do this? if so. HOW?

Is your Linksys Router is connected hardwired to the Netgear Router ?
If your both trhe router is connveted via cable...you can get the wireless signal from both the router.However your purpose will not get resolved because you want to repeat or extend the signal.In my opinion you may get a wireless Range Expander to resolve your Problem.

Similar Messages

Wireless connection between two macs.

I have a Intel iMac downstairs and a G4 power pc iMac upstairs. The downstairs iMac has an internet connection, upstairs does not. What do i need to have a wireless connection between the two and how do i go about connecting the two computers?

Hi widge-
What you need will depend on which Macs are already wireless and which you will have to add.
There is a lot more information available here: AirPort + Time Capsule
Luck-
-DP

Wireless connection between 2 routers

Hi All, I have 2 wireless routers. Router A is connected to the internet, and router B is a WRT54G and is connected to a computer. I want to have a network set in the following way INTERNET--wired-->ROUTER_A--wireless-->ROUTER_B--wired-->COMPUTER How should I configure router B to be able to have this network setup? Thanks, Andre

Andre,
so basically, your connection would go as follows, right??
modem - router A )) (( router B - computer
the WRT54G cannot connect to any access point wirelessly. it can only broadcast, not recieve.
if you wish to have a device that will work the way the illustration above goes then i would suggest a gaming adapter plus a switch/hub.. connection would be as follows...
modem - router A )) (( wireless gaming adaper - switch/hub - computer

Connection between two routers

Can´t ping from pc10 to pc15. It get's stuck on router4, because the communication between router4 and router2 is failling.
I would appreciate if somebody could help me!
Thanks in advance.

I dont have Packet tracer...
What is the ip address of the pc's?
Do you have route for both subnets in all routers?
Thanks,
Madhu.

How to make a connection between two wireless sensor networks of different groups through gateway?did any external device or coding is needed?

my objective is to make a connection between two wireless sensor networks....i am using two nodes and one gateway for each wireless sensor network.....what is the procedure for connecting these two wireless sensor networks of different groups

my objective is to make a connection between two wireless sensor networks....i am using two nodes and one gateway for each wireless sensor network.....what is the procedure for connecting these two wireless sensor networks of different groups

Wi-fi bridge between two routers TP-LINK WR841ND (WDS). HP 1536 dnf MFP connect to one of this routers (copper). My Ipad or Iphone can't find HP 1536 dnf MFP (using Eprint). Ipad and iphone connect to router across WiFi.

Hello.
I have wi-fi bridge between two routers TP-LINK WR841ND.
The name of this technology - WDS.
HP Laser JET 1536 dnf MFP connect to one of this routers (copper).
Second device (my NETBOOK) connect to second router (WiFi).
I have good communication between NETBOOK and HP Laser JET 1536 dnf MFP via WiFI-bridge.
In usual case NETBOOK can find (and can Ping) network printer and make a print some files.
But my Ipad or Iphone can't find HP Laser JET 1536 dnf MFP (using Eprint). Ipad and iphone connect
to router across WiFi.
Please, help!

Are you using the ePrint Mobile App, the ePrint Printer Control App, or just trying to send an email to the printer's ePrint email address?
Does AirPrint work?
-------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------

Can't establish wireless connection between the printer and computer.

I recently upgraded my wireless to an Apple AirPort Time Capsule. I'm able to set up the printer via USB cable. And I'm able to set up the printer on the network via the Airport WPA utility. However I cannot establish a wireless connection between the computer and the printer. When I go to the printers window in my system prefereces, there is no wireless printer available to add in the "available printers" menu. Only the USB version printer is listed and of course when I disconnect the USB cable it shows as offline.I've tried all the fixes on HP's support pages. I've tried reinstalling the printer on both the router and the computer numerous times. The only thing I haven't done is reinstall the printer using the "Install Wizard" software that is supposed to come with the printer - (mine never came with it in the first place and of course HP doesn't have it available for download). And when I reset the printer to factory settings, then connect it to the computer via the USB, there is no installation software that pops up. Cant even find the **bleep** thing in "Finder". (I'm assuming that it should show up as some sort of external device.) I've checked to make sure both computer and printer are on the same network. (sometimes my computer will grab a connection with the next nearest network.) I've checked all the settings for the printer via the HTML configuration utility. I've even updated my Macbook software and restarted it multiple times. Note: the printer actually worked for a bit when I first switched routers, but the printer's wireless function went offline several times and then quit altogether. Really frustrated that I bought another HP product thinking this time things would be different. HP is no help unless you want to pay $$ for a phone call. I'm about ready to take this thing out in the desert to use for target practice and never buy another HP product ever again.

Hi , I saw your post regarding the problems you are having with your LaserJet Pro P1102w Printer not showing on your Macintosh computer. I may have found some resources for you.
I have a few questions for you, so I can offer some additional assistance:Before you upgraded to the Apple AirPort Time Capsule, was the printer working wirelessly without any issues?
When you say; 'I reset the printer to factory settings', how where you trying to do this?
I found some instructions from this post: How do I reset my Laserjet p1102w to its defaults, copied here for you:
To restore the printer back to factory settings, turn the printer off, hold down the wireless button and the cancel button (x button) then turn the printer back on and don't release the two buttons until the printer stops making noise. (When they say turn the printer off, I think they mean unplug the power cable.)
"I've checked to make sure both computer and printer are on the same network." Do you know if you are able to access the printers Embedded Web Server (EWS)?To access the EWS - Make sure that the Ready light () is on and that the printer is idle and silent.Press and hold the Cancel button (), and release it when the Ready light () begins blinking.The configuration page prints.Type the IP address or host name of the product in the address field of a supported Web browser, and then press Enter on your keyboardLet me know if this page loads
To answer a few more items you have listed:... When I go to the printers window in my system preferences, there is no wireless printer available to add in the "available printers" menu.This could be an issue with your print system, I recommend resetting the printing system and then Repair Disk Permissions - after that try to add the printer again.
... the "Install Wizard" software that is supposed to come with the printer - (mine never came with it in the first place and of course HP doesn't have it available for download)HP provides their software/drivers to Apple to be released through your Apple software updates. You can review this document on how to Install a Mac Printer Driver Using Apple Software Update. Which leads into your next point...
... there is no installation software that pops upWhen you connect the USB cable your mac may still recognize the printer software as being already installed - check for apple updatesOn the Mac, click the Apple menu (), and then click Software Update, or click About this Mac, and then click Software Update. A list of available updates displays.
... Not seeing the printer in "Finder" From what I understand most printers will not show in Finder unless you install a memory card into a supported port on certain printer models, only then will it read it like an external device. A few more things you can check are that the new settings in the Apple AirPort Time Capsule are setup to allow the printer to communicate. There are several of these settings listed in this document; Tips and Workarounds for Common Wireless Network Printer Issues. HP regularly releases firmware updates that may also correct the problem you are experiencing. You can click on this link to Getting Printer Updates for HP LaserJet Pro P1102w Printer. I did find 2 more documents that may offer some additional information as well;HP LaserJet Pro P1102w Printer - Connecting the Printer After Changing Your Wireless NetworkAn 'Unable to Find Printer' Error Displays for the HP LaserJet Pro P1102w Printer Please let me know if any of these steps resolved your issue, or the details of what happened. I look forward to hearing from you, hopefully with good news! Thanks,

RFC connection between two SAP systems (with SAP router)

Hi!
I would like to set up a RFC-connection from SAP Solution Manager to other SAP system.
The network connection between the servers is VPN.
How can I set up this RFC-connection, if my connection between two SAP systems looks as follows,
(I use the following SAP routers)?
my server --> customer
my server --> internal SAP Router server xy (10.101....) --> SAP Router customer 2 (10.1....) --> SAP System customer (134....)
Back-way
SAP Systeme customer --> SAP Router customer (134.1....) --> internal SAP router (212.6....) --> my server
How can I set up this RFC-connection, if my connection between two SAP systems looks as follows,
(I use the following SAP routers)?
something like:
/H/10.101..../S/sapdp99/H/10.1.4..../S/sapdp99/H/134...
Thank you very much!
regards
Thom

Same answer as in the other forum where you cross posted....

Wireless connection between 2 buildings

My office is in a small separate structure on my residential property about 100 feet away from my 2 story house (both buildings are mostly wood frame, a lot of windows).
In the office is my computer system – internet access and a simple network:
Cable Modem
Linksys 2.4 GHz Wireless-B Router
2 PC's with Wireless-B
Mac Pro
Everything works excellent inside the office building (using wireless for the network and wired for the internet).
I just purchased a MacBook Pro for the house to access the internet and my files on my PC in the office. I tested it with the Linksys and just barely picked up some signal but mostly nothing.
I tried a Netgear WNDR3300 - their latest dual-band, with 5.0 N and 2.4 G. A very nice unit, worked out of the box, but no real additional signal strength.
I was thinking about trying 2 AirPort Extremes, one in the office building and one in the house.
What is someone’s best suggestion on how to create a solid wireless connection between 2 buildings (about 100 feet apart), not necessarily Apple equipment, and short of running an Ethernet cable between the 2 buildings.
I would like full wireless and wired access inside the office, and full wireless and wired access inside the house.

Do you have direct line-of-sight between the two buildings?
Wireless Bridges Point-to-Point Link Configuration Example

Setting up back-to-back async connection between 2 routers

Hi,
I am trying to setup a back-to-back async connection between 2 routers via the async serial interface. The connection between the two routers are via a smart serial to RS232 male(CAB-SS-232MT) cable connecting to another RS232 female to smart serial (CAB-SS-232FC) cable. What I am trying to do is to push the async data from one router (Router A) to another router (Router B).
When I try to capture the async data from the async serial interface on the source router (Router A) while disconnecting the back-to-back connection from Router B, it is showing the correct data. The data capture is via the smart serial to RS232 male cable connecting to Router A, to a PC via hyperterminal. But however, when the back-to-back connection is connected and I try to do a reverse telnet at Router B opening up the port for the async interface on Router B, it seems to be showing incorrect data. I have confirmed that the speed and configurations on both routers are matched.
Does it require to have two physical async modems in between both routers for signalling? Any experts who are familiar with such setups can advise on why the async data at Router B appear as incorrect with unreadable characters? Any help is greatly appreciated.

Hey Sebastian,
Had the same issue, which I just managed to get it resolved.
When you insert the modem, the router will create an Async interface for it lets say Async 0/1/0
then all what you've to do is:
chat-script DialOut ABORT ERROR ABORT BUSY "" "AT" OK "ATDT \T" TIMEOUT 45 CONNECT \c
line 0/1/0
exec-timeout 0 0
script dialer DialOut
modem InOut
transport preferred none
transport input all
transport output all
stopbits 1
speed 115200
flowcontrol hardware
and to dial a the remote router all what's required is:
reverse telnet to the above line (show line to know the line number) then type atdt
Let me know in case you still get issues

How to check the Network Connectivity between two systems.

Hello Everyone,
Please let me know different ways to check the network connectivity between two systems other than ping/traceroute commands.
Thank You.
Edited by: 835435 on Jan 20, 2012 11:43 AM
Edited by: 835435 on Jan 20, 2012 11:44 AM

Use snoop.
snoop -d <nic> - will give requests and replies coming/going in/out of the specified NIC.
snoop -d <nic> <MAC address of the target host> - will give requests coming from the required host.

The connection between two Tuxedo machines

We want to locate our servers(services) onto different machines, we want to know
:whether the connection,between two machines, is built up at the first time the
servers booted and kept persistently connectted, or just build up the connection
when there comes a request.

Remote machines connect to one another lazily. If you have machines A
(master), B and C, then B and C do not connect until a request is made
between B and C. All machines connect to the master at boot time.
roopesh wrote:
>
The connection is persistent and is not request based.
The machines communicate using BRIDGE.The DBBL which runs
on the primary master machines keep doing sanity checks
and health of BBL at all the machines connected and if
any BBL does not respond for the specified time(set by
DBBLWAIT) in RESOURCES section.then that machine gets partitioned by DBBL.
for more info you can read tuxedo documentation.
Thanks
Roopesh
"YANG YI" <[email protected]> wrote:
We want to locate our servers(services) onto different machines, we want
to know
:whether the connection,between two machines, is built up at the first
time the
servers booted and kept persistently connectted, or just build up the
connection
when there comes a request.

Gprs connection between two mobile phones

Hi
is it possible to make a gprs connection between two mobile phones without a server(pc...)? when the answer "yes" please give me an exapmle...

I'm not sure, I'm just connecting some facts. I'm talking about Siemens S55. It has implemented sockets (both client sockets and server sockets). The phone, when connected via GPRS has IP address (Siemens' netmonitor reports it..). But i've never tried to use server-socket on my mobile.
So it seems that it is in fact possible on some handsets. (AFAIK nokia 6610 and similar does not support sockets...)

Connection between two views

Hi Experts,
Please give me some inputs related to connection between two views ???

Hi
http://help.sap.com/saphelp_46c/helpdata/de/39/7dfeaaac6011d189c60000e829fbbd/frameset.htm
https://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/2cceb190-0201-0010-be88-acdbeb2ad65f
How to acces context of view B from view A without using the controller?
http://help.sap.com/saphelp_nw04s/helpdata/en/7b/67eaa71bdf2645be6e811eee980a04/frameset.htm

Connection between two clients

Hi,
I want to get some guidance on connection between two clients. Suppose I need to connect client 500 with client 900 in the same system without changing the logical names.
Thanks & Regards
Nabarun

Nabarun -
It almost sounds as if you just want an RFC to go from one client to the other. RFCs (SM59) are not client dependant so you can create one in any client. You can create one with the system name and point it to the client number using a specific user and password. I would recommend for security it be a communications user and not a dialog user depending on what you will be sending between the clients. However, the user will need the correct permissions and again, depending on what you are trying to accomplish, it may have to be a DIAG user although I would be wary. Then create a 2nd RFC pointing back to the other client. For example...
RFC 1
System Name = <System>
Client = 500
User = <userid in clnt 500>
RFC 2
System Name = <System>
Client = 900
User = <userid in clnt 900>
Then when you are in client 500, there is a path/connection to client 900 via that clients ID and password and vice versa using the appropriate RFC. Again, with out more info on what you are attempting, this may be your solution. Hope this helps. Good luck
Regards,
Zecher

Wireless Connection between two routers

Similar Messages

Maybe you are looking for