Wireless Control System Error Msgs.

Hi,
I have a problem with Wireless Control System (WCS v7)  WCS-STANDARD-K9 and installed with WCS-PLUS-100 (installed two licenses) so total licensed installed is for 200 Acesspoint's in WCS. I have 149 AP's connected to WCS and its shows error " System is in voilation of license. The number of APs (149) registered is greater than licensed (0). Please go to the license center under the Administation Menu to add additional WCS licenses.
What would be the reason for this error,? Thanks

If you go to the license center in WCS, do you see a total of 200 AP support. You need to make sure you have a base license before you add additional plus license. I had an issue before, where I added a whole bunch of plus license after I installed a 250 base. I had 400+ APs and ran into the same issue but I had 250 base. Well I forgot to add the other 250 base so I had to remove all the plus license before I could add the other 250 base. Then I had to add all those plus license after that. The license center will tell you exactly how many APs it will support. From what you posted, it looks like you have 0.
Sent from Cisco Technical Support iPhone App

Similar Messages

  • Cisco Wireless Control System need wireless Lan Controller ?

    Cisco Wireless Control System need wireless Lan Controller , for Rogue detection

    Hi Joao,
    The WCS is used in conjuntion with the WLC (Wireless Lan Controller) for Rogue Detection. It is not a must for this function but more of an add-on :)
    The Cisco WCS is an optional network component that works in conjunction with Cisco Aironet Lightweight Access Points, Cisco wireless LAN controllers and the Cisco Wireless Location Appliance.
    From this doc;
    http://www.cisco.com/en/US/products/ps6305/index.html
    Overview of WCS
    The Cisco Wireless Control System (WCS) is a Cisco Unified Wireless Network Solution management tool that adds to the capabilities of the web user interface and command line interface (CLI), moving from individual controllers to a network of controllers. WCS includes the same configuration, performance monitoring, security, fault management, and accounting options used at the controller level and adds a graphical view of multiple controllers and managed access points.
    WCS runs on Windows 2003 and Red Hat Enterprise Linux ES 4.0 and AS 4.0 servers. On both Windows and Linux, WCS can run as a normal application or as a service, which runs continuously and resumes running after a reboot.
    The WCS user interface enables operators to control all permitted Cisco Unified Wireless Network Solution configuration, monitoring, and control functions through Internet Explorer 6.0 or later. Operator permissions are defined by the administrator using the WCS user interface Administration menu, which enables the administrator to manage user accounts and schedule periodic maintenance tasks.
    WCS simplifies controller configuration and monitoring while reducing data entry errors with the Cisco Unified Wireless Network Controller autodiscovery algorithm. WCS uses the industry-standard SNMP protocol to communicate with the controllers.
    From this good doc;
    http://www.cisco.com/en/US/products/ps6305/products_configuration_guide_chapter09186a00806b7270.html#wp1131195
    Detect and Locate Rogue Access Points
    From this WCS doc;
    http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a00806f070a.shtml#new5
    Rogue Detection under Unified Wireless Networks
    http://www.cisco.com/en/US/tech/tk722/tk809/technologies_white_paper09186a0080722d8c.shtml
    Hope this helps!
    Rob

  • Cisco wireless control system

    we are using cisco wireless control system i need block some MAC address or devices how can i do it

    Hi,
    Yes you can block the specific client using MAC Address filtering option in WCS
    This option is avialbe in Configure> Security >MAC Filtering
    here you can create new template as per your requirement
    Go through below link for detail knowledge.
    http://www.cisco.com/c/en/us/td/docs/wireless/wcs/7-0/configuration/guide/WCS70cg/7_0temp.html#wp1095263

  • Can Wireless Control System Send Alarms As Traps to a trap receiver

    Can the Cisco Wireless Control System be configured to send its alarms as SNMP traps to a specified trap receiver ? if so how is that capability configured ? is it thru Notification Receiver ?

    Yes, it can. And yes through the Notification Reciever. Pity though, it can only send traps in regards to Guest Account Activity such as guest association and authentication.
    Hopefully future versions of WCS will be more versatile in that regard.
    Cheers

  • WAP200E and Cisco Wireless Control System

    Hi.
    I have a customer with a linux OS machine running Cisco Wireless Controll System.
    He needs are to add a new wireless AP with the following features :
    - compatible with most laptops
    - exterior conditions "resistant" (sun, rain...)
    - reasonnable performance (the AP would be a a roof with people on the roof itself, max distance : 15 meters, no walls)
    AND
    Which product would you recommend ?
    I saw the WAP200E but I have no idea
    - if it is compatible with Cisco Wireless Control System
    - what antenna(s) to buy

    Hi Yves,
    The WAP200E is not compatible with the WCS.
    1.  How high (in relation to the client) is the AP going to be installed?
    2.  How is the AP going to be installed?  Will it be hanging down?
    3.  Do you need Cisco CleanAir?

  • Wireless Control System Software

    I could use some recommendations from the forums here. I have an 8-story apartment building in which the building management wants to install wireless to cover everyone and every floor. They also want to be able to manage all the APs from a centralized location. Obviously, a challenge since this is a new building and I can't do a site curvey yet.
    But here's what I'm thinking from a theoretical standpoint. I'd probably want as many 1242AG access points as needed for actual coverage (anywhere from 2-20), since they handle lots of walls, etc. better than most other APs. I'd also want a 4402 WLAN Controller for handling anyone moving around, etc. Finally, I'd need the Wireless Control System software running on a server connected to the WLAN Controller.
    First of two questions: does this all make sense to you, or am I over (or under-) thinking this?
    Second question: I've found plenty of places where we can purchase licenses for the Wireless Control System software, but where is the software itself? Is it a free download with no licenses? Or does it come with the 4402 or something?
    Any and all help would be greatly appreciated.

    Hi
    You maybe don't need WCS - it's an nice extra, but you can just get a 4400-series controller and some APs and still configure security policies etc centrally and have the RF side of things auto-managed.
    I'd get a 4400, and I'd get 1000-series APs (1010s if you just want built in antennaes or 1020s if you want to add external ones - 1010s should be find in most scenarios).
    I've not used any 1200 series with the controllers yet, but heard reports of problems and the LWAPP firmware for these is pretty new - probably best to stick with the tried and tested ones for now.
    Just leave yourself capacity on your 4400 controller for more APs in case you have some poor coverage areas, you can then just chuck up another AP to plug the hole, as it were...
    Aaron
    Please rate helpful posts.

  • About Wireless Control System (WCS)

    First, I'm not Bilingual so excuse my English.
    Dear Sirs,
    Please teach Wireless Control System (WCS).
    Whether "Windows 2003 Enterprise" is supported from the following evidence is not understood.
    Is "Windows 2003 Enterprise" supported?
    Table 3. Product Specifications for Cisco WCS
    Operating system
    Windows 2003 SP1 or greater,
    http://www.cisco.com/en/US/products/ps6305/products_data_sheet0900aecd802570d0.html#wp9000279
    Best regards,

    Yes, Windows 2003 server will be supported. Here are the requirements for installing WCS. http://www.cisco.com/en/US/products/ps6305/products_configuration_guide_chapter09186a00808317da.html#wp1061082

  • License WCS (Wireless Control System) Problem to install

    Hello,
    I'm Christopher, I have a need to update the WCS and license this, but when I perform the load operation, this throws me this message.
    "You must have Base a license in order to install an upgrade license"
    How I can fix it?

    Hi Christopher,
    Base license should always be installed before you can upgrade license count.
    For ex if you buy 2 AP's initially and got WCS license with them and installed then on WCS.
    Now after few days you buy few more AP's and want to add them to WCS you won't be able to do so unless you have base license. So please contact license team to get base license(Only needs to be installed once not everytime.)

  • Wireless Control System Question

    Hello ...
    Can someone tell me how I can see a list of clients connected to a specific access point using the WCS?  I cant seem to find the location in WCS that provides this info.
    Also - can I specify which AP the client connects to via the WCS?
    Thanks,

    Go to the search box and enter the AP your your choice.  You'll get an option of either Monitor or COnfigure.  Choose Monitor.  Choose the AP of your choice.  Go to the fourth tab:  Current Associated Clients.
    Also - can I specify which AP the client connects to via the WCS?
    Specify a different SSID and configure AP Groups.  YOU can configure your clients to connect to a specific AP.

  • Wireless control system

    hi! If i did not select the "Apply to AccessPoint" during the creation of new controller template process wizard thru the Controller Template Launch Pad (assuming that i;ve successfully applied the template to wlc), will i be able to apply/see the AP in the Lightweight AP template creation (select APs tab)? What's the different between adding the AP in the controller template launch pad and Lightweight AP template creation page? Must i include the AP into the controller template launch pad before i can see it in the Lightweight AP template creation page?
    Thx

    Hi,
    if I understood correctly what you were talking about, applying a template on APs through the controller launch pad applies it to all APs currently associated to a controller while selecting APs manually in the AP template launch pad applies it to selected APs regardless of the WLC they are on.\\
    How do APs appear in the select list of the templates ? Simply by WCS knowing them, so usually by being associated to an WLC that WCS knows.
    Nicolas

  • WCS (wireless controll system) old alarms

    I'm trying to see the old alarms from WCS, I mean on top of the screen displayed Alarms summary specifically critical alarms (red triangle) when these alarms are resolved which is the record that there ever was this alarm
    can any one help my thanx

    Hi,
    You may be able to find back cleared alarms through an advanced search, by choosing Alarms as a Search Category and maybe other parameters such as Clear as a Severity.
    Hope this helps,
    Fede
    If  this helps you and/or answers your question please mark the question as  "answered" and/or rate it, so other users can easily find it.

  • Error Msg 2203 on install of Adobe Reader X

    When I attemp to install Adobe Reader X I get error msg 2203 and system error msg #2147287035

    Do you already have an earlier version of Adobe Reader installed?  If so, remove it using http://labs.adobe.com/downloads/acrobatcleaner.html then try the install again.
    If the error still occurs, please give us the full and exact error message.

  • ITunes no longer works on my Windows VISTA system.  Get error msg saying C runtime library incorrectly... Error 7, Windows error 1114..

    iTunes no longer works on my Windows VISTA system.  Get error msg saying an application is attempting to access C runtime library incorrectly... Error 7, Windows error 1114.  Same msg, or one that says unable to install, when trying to update or reinstall iTunes.  iTunes worked well up until about a month ago when this error msg starting appearing.

    Go to Control Panel > Add or Remove Programs (Win XP) or Programs and Features (later)
    Remove all of these items in the following order:
    iTunes
    Apple Software Update
    Apple Mobile Device Support (if this won't uninstall move on to the next item)
    Bonjour
    Apple Application Support
    Reboot, download iTunes, then reinstall, either using an account with administrative rights, or right-clicking the downloaded installer and selecting Run as Administrator.
    The uninstall and reinstall process will preserve your iTunes library and settings, but ideally you would back up the library and your other important personal documents and data on a regular basis. See this user tip for a suggested technique.
    Please note:
    Some users may need to follow all the steps in whichever of the following support documents applies to their system. These include some additional manual file and folder deletions not mentioned above.
    HT1925: Removing and Reinstalling iTunes for Windows XP
    HT1923: Removing and reinstalling iTunes for Windows Vista, Windows 7, or Windows 8
    tt2

  • Unable connect System Update (LNV Prod Center). Error msg: Unable access Proxy server.

    I have a X61s Model 27G.
    I cannot perform System Update via Lenovo Productivity Center. Gives error msg (in my native language pt) that
    unnable access Proxy server.
    I have a wireless broadband conx and  access net  without problems. Can someone help?
    Brgds Edu

    edutex wrote:
    I have a X61s Model 27G.
    I cannot perform System Update via Lenovo Productivity Center. Gives error msg (in my native language pt) that
    unnable access Proxy server.
    I have a wireless broadband conx and  access net  without problems. Can someone help?
    Brgds Edu
    I think I've posted this in the TVT forum as well, but I'll go ahead and respond here, cos that's easier than tracking down previous posts
    It's probably your proxy settings in IE, which is where TVSU gets its network access info.  Do this:
    Open IE
    Click Tools -> Internet Options
    Click Connections Tab
    Click "LAN Settings" button
    Check your proxy settings.  Most likely you want to use "Automatically detect settings" and clear any other checkboxes.
    Click OK
    Click OK
    TVSU should work now.
    Full disclosure: Lenovo issues my paychecks.

  • I ve updated my i pod touch to version 6.0.1. Installation got failed with some error msg, and now my i pod is not getting detedted in my system.Help me to fix it up.

    i ve updated my i pod touch to version 6.0.1. Installation got failed with some error msg, and now my i pod is not getting detedted in my system.Help me to fix it up.

    What's the error mesage?

Maybe you are looking for