Wireless Controller with 802.1x

Hi.
This may seem like a stupid question, but if i'm using 802.1x on my wireless network and using RADIUS/LDAP/ACS for authentication, do I need to configure any aaa commands on my access switches? It was my understanding that all traffic from the client is tunnelled back to the controller so this is not necessary?
Thanks.

No commands necessary on your switches. Your WLC has radius servers configured and the WLC will communicate with your radius.
Sent from Cisco Technical Support iPhone App

Similar Messages

Cisco 5508 Wireless Controller with Splash Page Disclaimer

How do one configure a splash disclaimer page on a Cisco Wireless Controller 5508 with no authentication?
Jimmy

There are many options to you in this scenario, but if you're looking to simply provide a splash page via the WLC without interacting with any other web servers, you can configure Local Web Authentication (LWA) as seen in this configuration example.
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wlan-security/69340-web-auth-config.html?referring_site=RE&pos=1&page=http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wlan-security/71881-ext-web-auth-wlc.html
If you are not wanting the authentication, you can choose the "passthrough" method which will not require any credentials, only accepting an AUP or whatever you want.

Securing a wireless network with 802.1x + WPA

I'm currently in the process of designing a new wireless network and am looking to do both authorization from a RADIUS server (Active Directory) and encryption using WPA. Rather than setting a pre-shared key and distributing it to all the users I would rather have the AP automatically distribute the encryption key after the user has authenticated. Is this possible? If so, which Cisco AP's support this functionality?

I don't think you can do that. You might want to think about the following (if you have all Windows clients)
- Use PEAP machine authentication and push out the config (over the wire) via GPO
- Configure a domain controller with PKI (Certificate Services) and machine auto-enrollment. Use EAP-TLS for authentication, and push out the wireless config via GPO
- Use WPA with PSK and push out the config via GPO.
The only problem is that your wireless client config would need to be pushed out over the wire (not wireless) via GPO. This also assumes that your wireless supplicant is Wireless Zero Config (and not the Intel PROset or Cisco Aironet stuff).
I'm afraid you're going to have to touch the machines one way or the other, but you can touch them remotely (via GPO) or touch the manually to configure the wireless settings.

How do I configure the 2504 Wireless controller with AP?

I recently purchase the 2504 wireless controller and the 1602i AP. I was able to do the basic setup of the controller and can now access the web interface, but the AP is not being detected and I am unable to add it.

First of all: 1602 AP need minimum software version on WLC: 7.4.100.0
paste this info:
sh sysinfo from WLC
sh version from AP.
Did you create a DHCP pool for APs to get IP ?
Try to to be keep AP and WLC on same subnet.
regards

5500 Wireless Controller with 7.6.130 - IPv6 address

Hello,
We have configured ISE as the RADIUS for one of our SSID's. What we are noticing is a large number of clients are getting assigned a ipv6 address.
We are not sure what changed and trying to trouble shoot ? We do not have ipv6 enabled on our DHCP . Is this something the clients are reqiesting ?
Do we need to change something on the Wireless Controller ? Appreciate your input.

Disable IPv6 globally on your WLC. You can use below WLC CLI command to do this
config ipv6 disable
HTH
Rasika
*** Pls rate all useful responses ****

Wireless AP with 802.1x

Does anyone have experience, and is willing to share, on setting up access points where the connected users are authenticated through 802.1x?
Here is my setup. Cisco 1240AG and 1131AG connected to an 802.1x enabled switch. The switch gets puts users on different VLANS depending on access (wired authentication already works). MS Server 2008 acting as RADIUS.
My goal is to have one SSID. When guests connects, they do not authenticate and are put on a guest VLAN. Authenticated users are put on a different VLAN.
Thank you in advance for any help on this subject.

Hi,
I am trying to implement 802.1X authentication in enterprise environment with access switch WS-C3750-48TS-E (C3750 Software (C3750-IPSERVICES-M), Version 12.2(50)SE3).
I am using dynamic VLAN assignments, like guest VLAN, restricted(critical) VLAN, unauthorized VLAN for wired clients.Everything if fine for them.
I want to use only one SSID for wireless clients. Is it possible to use "authentication host-mode multi-auth" command for configuring switch port with connected Cisco AP 1242G to it ?
Example configuration:
description Cisco 1242G AP
switchport access vlan 2223
switchport mode access
switchport voice vlan 998
authentication event fail retry 1 action authorize vlan 2226
authentication event server dead action authorize vlan 2227
authentication event no-response action authorize vlan 2224
authentication event server alive action reinitialize
authentication host-mode multi-auth
authentication port-control auto
authentication periodic
authentication timer reauthenticate 300
authentication violation protect
mab
dot1x pae authenticator
dot1x timeout quiet-period 10
dot1x timeout tx-period 1
dot1x max-reauth-req 1
spanning-tree portfast
spanning-tree bpduguard enable
Do I have to enable 802.1X auth on the AP or it has to be pass-through for wireless clients and be the client of the switch itself (with its MAC address) ?
Thank you in advance !

Extending home wireless network with 802.11b/g Airport Expresses

Home Setup: iMac with iSight G5 2.1GHz PPC, OS X Leopard 10.5.8, 2.5GB memory, 2 Airport expresses-802.11b/g.
Up to just recently, I was able to use my AE's to create a whole house wireless network: one as my main network connected to my cable modem, and the other as a wireless network extender. My extender got pulled out one day accidentally, and when I went to plug it in it wouldn't reconnect to my network...and so the problems began. Airport Utility used to give the option of "Extending the Wireless Network", but no more.
I've done a lot of searching through the forums regarding this issue, read through the sage advice by superusers Tesserax and Bob Timmons, and attempted to set up my main AE as my "WDS Main" AE and the other as my "WDS Remote". The WDS main connects fine to the internet, but the WDS remote continues to show a flashing amber light and inability to extend my wireless network. I've done soft and hard resets to the remote AE (which transiently gives me a green light, then back to flashing amber), network diagnostics using the Airport utility, but still no luck. The AE wireless extender continues to flash amber and is nonfunctional.
AE Wireless extender settings reported:
-WIreless Mode: Create a wireless network
-Connect using: Ethernet
AE Errors reported:
-Ethernet Unplugged
-Default Settings
I setup the AE Wireless extender as a WDS Remote, it resets and shows "Normal" without problems reported in the summary window of Airport Utility. Connection indicated as "Airport (WDS)" and Wireless Mode reads "participate in a WDS network", but the AE is still flashing amber and will not connect to the internet or Main WDS wireless network.
Went to the Genius Bar at the local mac store...they couldn't help at all.
I'm out of answers...help?!
Allan

There are basically two "flavors" of WDS that the AirPorts support: static & dynamic.
o A static WDS allows for a main, relay, and remote base stations in the configuration. This only operates in the 802.11g radio mode. Its advantage is it is well suited when you are trying to cover a considerable linear range ... like a rectangular house where the Internet connection comes in at one of the shorter sides and you want wireless at the other end. The biggest disadvantage of this type of WDS is that for every base station added, you lose half the overall bandwidth.
o A dynamic WDS allows for only a single main and multiple remotes. Think of a wheel with the main at the center and the remotes as spokes of the wheel. The advantage of this type of WDS is it operates in the 802.11n radio mode and doesn't suffer a significant bandwidth loss like the static version.
As a minimum, a dynamic WDS requires two 802.11n AirPorts (or Time Capsules). You can create a static WDS with either all 802.11g AirPorts or a mix of 802.11n & 802.11g AirPorts. Note; however, you cannot create a dynamic WDS with mixed mode base stations.

2504 Wireless Controller with multiple IP Networks

I am wanting to deploy a 2504 with 8 AP's that can support three IP networks simultaneously, 10.130.0.0, 192.168.0.0 and 192.168.1.10 (Guest Network). I understand this is supported, but haven't really seen any examples of how to accomplish this. Any suggestions?

Jerryard1,
Just a followup on what I was able to do.
I have the 10.130.0.0 network on the management interface, port 1 with dynamic AP management enabled. I then created a dynamic interface for the 192.168.1.0 network and have that on port 3, with dynamic AP disabled, both ports are untagged for VLAN's.
I then created a WLAN for each, but pointed the WLAN for 192.168.1.0 to the dynamic interface I created. The WLAN for 10.130.0.0 is pointed to the management interface. All AP's come up on the 10.130.0.0 network. Physical ports 1 and 3 on the 2504 are connected to it's respective switch stack.
I then enabled routing on their Sonicwall firewall to route between the two networks, all seems to work fine.

Problem getting Airprint (Bonjour) to communicate to HP LaserJet CP1525nw printer across a Cisco 5508 Wireless Controller

I cannot get my IPad2 to print (it cannot find the printer) using a Laserjet CP1525nw color printer across a wireless network using a Cisco 1508 Wireless Controller with 49 wireless access points. HELP!!!!
What is the secret to getting Bonjour to work on it?
I can get the IPad2 to locate the HP CP1525nw printer without a hitch using a low budget Netgear WAG102 stand alone wireless access point on the same network.

If it helps somebody, here is what you need to do.
It worked for me, but only in Multicast-Unicast mode.
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_tech_note09186a0 080bb1d7c.shtml

Wireless Controller locking down User per SSID

I am using Wireless Controller 4112. We use WPA enterprise mode for authentication and encryption via Microsoft IAS server and MS AD domain.
My question is how to lock down a user to a specific SSID? I would guess that this is via some vendor specific radius attributes, am I right? And if so, what would be the name (and ID) for the attributes?
Thanks in advance.

Making progress in setting up the wireless controller with multiple VLAN and WLAN/SSID. I create a virtaul interface at the controller and assign a VLAN number to it. The controller mgmt port is also set to a trunk port. Create a new SSID WLAN and have it mapped to the new virtual interface. Things work good.
The new problem I am trying to solve is how to prevent wired users to access the controller admin web interface via the virtual interface IP. I try create ACL and map it to the virtual interface. It doesn't seem working.

Config air-lap1041n-e-k9 with cisco 5500 (5508) series wireless controller. how to?

Hi!
I try to configure a Cisco 5508 Wireless controller and 25 Air-lap1041 to use as VoIP and data. I read documents, manuals, etc, but the AP doesn't charge the configuration, or not conect with the Wireless Controller, why? No Radius server present, only WPA security.howto, please...
I try to put a static ip in the LAP, with lwapp or capwap command, (LWAPP/CAPWAP ap ip address direccion mascara) and the AP returns "You should configure Domain and Name Server from controller CLI/GUI." and i can't change the name of the AP (Command is disabled).
Log from AP:
using ÿÿÿÿ ddr static values from serial eeprom
ddr init done
Running Normal Memtest...
Passed.
IOS Bootloader - Starting system.
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
Xmodem file system is available.
DDR values used from system serial eeprom.
WRDTR,CLKTR: 0x83000800, 0xc0000000
RQDC, RFDC : 0x80000037, 0x00000184
PCIE0: link is up.
PCIE0: VC0 is active
PCIE1: link is NOT up.
PCIE1 port 1 not initialize
PCIEx: initialization done
flashfs[0]: 6 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 32385024
flashfs[0]: Bytes used: 2369024
flashfs[0]: Bytes available: 30016000
flashfs[0]: flashfs fsck took 21 seconds.
Reading cookie from system serial eeprom...Done
Base Ethernet MAC address: 44:2b:03:dc:09:25
Ethernet speed is 1000 Mb - FULL duplex
Loading "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx"...###########################
File "flash:/c1140-rcvk9w8-mx/c1140-rcvk9w8-mx" uncompressed and installed, entr
y point: 0x4000
executing...
enet halted
              Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706
Cisco IOS Software, C1040 Software (C1140-RCVK9W8-M), Version 12.4(23c)JA, RELEA
SE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 01-Jun-10 12:53 by prod_rel_team
Proceeding with system init
Proceeding to unmask interrupts
Initializing flashfs...
FLASH CHIP: Numonyx P33
Checking for Over Erased blocks
flashfs[1]: 6 files, 2 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 32126976
flashfs[1]: Bytes used: 2369024
flashfs[1]: Bytes available: 29757952
flashfs[1]: flashfs fsck took 7 seconds.
flashfs[1]: Initialization complete.
flashfs[2]: 0 files, 1 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 11999232
flashfs[2]: Bytes used: 1024
flashfs[2]: Bytes available: 11998208
flashfs[2]: flashfs fsck took 1 seconds.
flashfs[2]: Initialization complete....done Initializing flashfs.
Ethernet speed is 1000 Mb - FULL duplex
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-LAP1041N-E-K9    (PowerPC405ex) processor (revision B0) with 98294K/32
768K bytes of memory.
Processor board ID FCZ1611W414
PowerPC405ex CPU at 333Mhz, revision number 0x147E
Last reset from reload
LWAPP image version 7.0.94.21
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 44:2B:03:DC:09:25
Part Number                          : 73-14034-04
PCA Assembly Number                  : 800-34273-05
PCA Revision Number                  : A0
PCB Serial Number                    : FOC16075VZ3
Top Assembly Part Number             : 800-34284-03
Top Assembly Serial Number           : FCZ1611W414
Top Revision Number                  : A0
Product/Model Number                 : AIR-LAP1041N-E-K9
% Please define a domain-name first.
Press RETURN to get started!
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:00:09.574: *** CRASH_LOG = YES
Base Ethernet MAC address: 44:2B:03:DC:09:25
*Mar 1 00:00:09.838: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log
(contains, 1024 messages)
*Mar 1 00:00:11.848: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state
to up
*Mar 1 00:00:11.892: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1040 Software (C1140-RCVK9W8-M), Version 12.4(23c)JA, RELEA
SE SOFTWARE (fc3)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Tue 01-Jun-10 12:53 by prod_rel_team
*Mar 1 00:08:16.954: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
logging facility kern
        ^
% Invalid input detected at '^' marker.
*Mar 1 00:08:28.047: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROL
LER
*Mar 1 00:08:28.049: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Mar 1 00:09:08.282: %CDP_PD-2-POWER_LOW: All radios disabled - LOW_POWER_CLASS
IC_NO_INJECTOR_CONFIGURED AIR-CT5508-K9 (c464.138f.9345)
*Mar 1 00:09:08.282: -Verify the required power-injector is installed on this
port: AIR-CT5508-K9(Gig 0/0/2).
*Mar 1 00:09:08.282: -If a power-injector is installed, issue the command:"pow
er inline negotiation injector installed"
*Mar 1 00:12:19.976: %CAPWAP-5-STATIC_TO_DHCP_IP: Could not discover WLC using
static IP. Forcing AP to use DHCP.
*Mar 1 00:12:29.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:12:39.994: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:12:49.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:12:59.994: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:13:09.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
Not in Bound state.
*Mar 1 00:13:19.993: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:13:19.993: %CAPWAP-5-DHCP_RENEW: Could not discover WLC using DHCP IP
. Renewing DHCP IP.
logs from wireless controller:
(Cisco Controller) >show interface summary
Interface Name                   Port Vlan Id IP Address      Type    Ap Mgr Gu
est
ap-manager                       2    untagged 209.165.200.231 Dynamic Yes    No
management                       1    untagged 209.165.200.230 Static Yes    No
service-port                     N/A N/A      192.168.1.157   Static No     No
virtual                          N/A N/A      1.1.1.1         Static No     No
(Cisco Controller) >
i conect with service-port ok and the management port works, i think.
AP442b.03dc.0925>ping 209.165.200.230
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 209.165.200.230, timeout is 2 seconds:
Success rate is 100 percent (5/5), round-trip min/avg/max = 1/1/1 ms
AP442b.03dc.0925>
Help, please!
i write in spanish:
Hola:
Tengo que configurar un cisco 5508 wireless controller con 25 air-lap1041n, para usarlo como acceso de datos y voz. ¿Cómo lo hago? He leído manuales, y seguido las instrucciones, pero el punto de acceso parace que no es capaz de cargar el perfil. No hay servidor radius, solo la configuración de una clave wpa. Alguién me puede indicar pasos, Gracias

Hi!
I buy a gigabit switch. I connect the service-port to gigabit switch, and laptop to gigabit switch. I used 192.168.1.x ip address (192.168.1.157 to service-port and 192.168.1.233 to wired port on laptop, well, the laptop has two ip adress, 192.168.1.233 and 209.165.200.2, and the laptop works ok. Ping to 209.165.200.230 -ip address of management interface- and ping to 209.165.200.203 -ip address for AP, is assigned by DHCP of WLC. And i connect the ap to gigabit switch, and the wlc assigns well an ip direction.
I post the run-config and sysinfo log. The gigabit switch is tp-link model tl-sg1005d, no configuration.
Before the logs, I see this message from AP:
*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
version 6.0.199.4 ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
Hola:
He comprado un switch gigabit. Conecto el service-port al switch gigabit y el portátil también (por cable). Uso como direcciones ip el rango 192.168.1.x (192.168.1.157 asignado al service-port y 192, 168.1.233 al portátil, bueno, el portátil tiene dos direcciones, la dicha anteriormente y la 209.165.200.2) El portátil funciona bien, hace ping al 209.165.200.230 - la ip de la management interface, y a 209.165.200.203 - ip asignada al AP por el DHCP del WLC. He conectado el AP al swtich gigabit, y el dhcp del wlc asigna correctamente una dirección ip.
Añado a continuación los resultados de los comandos "show run-config" y "show sysinfo". El switch es un TP-LINK modelo TL-S1005D, sin necesidad de configuración.
Antes de mostrar los resultados de los comandos, he visto el siguiente mensaje en el log del AP:
*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
version 6.0.199.4 ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
Un saludo
Antonio R.
(Cisco Controller) >show run-config
Press Enter to continue...
System Inventory
NAME: "Chassis"    , DESCR: "Cisco Wireless Controller"
PID: AIR-CT5508-K9, VID: V02, SN: FCW1608L05X
Burned-in MAC Address............................ C4:64:13:8F:93:40
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 25
Press Enter to continue or to abort
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 6.0.199.4
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console
1.27
Build Type....................................... DATA + WPS
System Name...................................... CISCO-CAPWAP-CONTROLLER
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 209.165.200.230
Last Reset....................................... Power on reset
System Up Time................................... 0 days 0 hrs 17 mins 45 secs
System Timezone Location......................... (GMT +1:00) Amsterdam, Berlin,
Rome, Vienna
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... ES - Spain
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +36 C
External Temperature............................. +23 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Disabled
Number of WLANs.................................. 1
3rd Party Access Point Support................... Disabled
Number of Active Clients......................... 0
Burned-in MAC Address............................ C4:64:13:8F:93:40
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 25
Press Enter to continue or to abort
Switch Configuration
802.3x Flow Control Mode......................... Disable
FIPS prerequisite features....................... Disabled
secret obfuscation............................... Enabled
Network Information
RF-Network Name............................. hosp
Web Mode.................................... Disable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Enable
Secure Shell (ssh).......................... Enable
Telnet...................................... Disable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
AP Multicast/Broadcast Mode................. Unicast
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Enabled
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Disable
Mgmt Via Dynamic Interface.................. Disable
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
AP Fallback ................................ Enable
Web Auth Redirect Ports .................... 80
Fast SSID Change ........................... Disabled
IP/MAC Addr Binding Check .................. Enabled
Press Enter to continue or to abort
Port Summary
           STP   Admin   Physical   Physical   Link   Link
Pr Type   Stat   Mode     Mode      Status   Status Trap     POE    SFPType
1 Normal Forw Enable Auto       1000 Full Up     Enable N/A     1000BaseTX
2 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
3 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
4 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
5 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
6 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
7 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
8 Normal Disa Enable Auto       Auto       Down   Enable N/A     Not Present
Press Enter to continue or to abort
AP Summary
Number of APs.................................... 0
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name             Slots AP Model             Ethernet MAC       Location
     Port Country Priority
Press Enter to continue or to abort
Press Enter to continue or to abort
AP Location
Site Name........................................ default-group
Site Description.................................
WLAN ID          Interface          Network Admission Control
1               management           Disabled
AP Name             Slots AP Model             Ethernet MAC       Location
     Port Country Priority GroupName
Press Enter to continue or to abort
AP Config
Press Enter to continue or to abort
Press Enter to continue or to abort
AP Airewave Director Configuration
Press Enter to continue or to abort
802.11a Configuration
802.11a Network.................................. Disabled
11nSupport....................................... Enabled
      802.11a Low Band........................... Enabled
      802.11a Mid Band........................... Enabled
      802.11a High Band.......................... Enabled
802.11a Operational Rates
    802.11a 6M Rate.............................. Mandatory
    802.11a 9M Rate.............................. Supported
    802.11a 12M Rate............................. Mandatory
    802.11a 18M Rate............................. Supported
    802.11a 24M Rate............................. Mandatory
    802.11a 36M Rate............................. Supported
    802.11a 48M Rate............................. Supported
    802.11a 54M Rate............................. Supported
802.11n MCS Settings:
    MCS 0........................................ Supported
    MCS 1........................................ Supported
    MCS 2........................................ Supported
    MCS 3........................................ Supported
    MCS 4........................................ Supported
    MCS 5........................................ Supported
    MCS 6........................................ Supported
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
    MCS 7........................................ Supported
    MCS 8........................................ Supported
    MCS 9........................................ Supported
    MCS 10....................................... Supported
    MCS 11....................................... Supported
    MCS 12....................................... Supported
    MCS 13....................................... Supported
    MCS 14....................................... Supported
    MCS 15....................................... Supported
802.11n Status:
    A-MPDU Tx:
        Priority 0............................... Enabled
        Priority 1............................... Disabled
        Priority 2............................... Disabled
        Priority 3............................... Disabled
        Priority 4............................... Disabled
        Priority 5............................... Disabled
        Priority 6............................... Disabled
        Priority 7............................... Disabled
Beacon Interval.................................. 100
CF Pollable mandatory............................ Disabled
CF Poll Request mandatory........................ Disabled
CFP Period....................................... 4
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
CFP Maximum Duration............................. 60
Default Channel.................................. 36
Default Tx Power Level........................... 0
DTPC Status..................................... Enabled
Fragmentation Threshold.......................... 2346
TI Threshold..................................... -50
Legacy Tx Beamforming setting.................... Disabled
Traffic Stream Metrics Status.................... Disabled
Expedited BW Request Status...................... Disabled
World Mode....................................... Enabled
EDCA profile type................................ default-wmm
Voice MAC optimization status.................... Disabled
Call Admision Control (CAC) configuration
Voice AC:
   Voice AC - Admission control (ACM)............ Disabled
   Voice max RF bandwidth........................ 75
   Voice reserved roaming bandwidth.............. 6
   Voice load-based CAC mode..................... Disabled
   Voice tspec inactivity timeout................ Disabled
   Voice Stream-Size............................. 84000
   Voice Max-Streams............................. 2
Video AC:
   Video AC - Admission control (ACM)............ Disabled
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
   Video max RF bandwidth........................ Infinite
   Video reserved roaming bandwidth.............. 0
Press Enter to continue or to abort
802.11a Advanced Configuration
Press Enter to continue or to abort
802.11a Airewave Director Configuration
RF Event and Performance Logging
Channel Update Logging......................... Off
Coverage Profile Logging....................... Off
Foreign Profile Logging........................ Off
Load Profile Logging........................... Off
Noise Profile Logging.......................... Off
Performance Profile Logging.................... Off
TxPower Update Logging......................... Off
Default 802.11a AP performance profiles
802.11a Global Interference threshold.......... 10 %
802.11a Global noise threshold................. -70 dBm
802.11a Global RF utilization threshold........ 80 %
802.11a Global throughput threshold............ 1000000 bps
802.11a Global clients threshold............... 12 clients
Default 802.11a AP monitoring
802.11a Monitor Mode........................... enable
802.11a Monitor Mode for Mesh AP Backhaul...... disable
802.11a Monitor Channels....................... Country channels
802.11a AP Coverage Interval................... 180 seconds
802.11a AP Load Interval....................... 60 seconds
802.11a AP Noise Interval...................... 180 seconds
--More or (q)uit current module or to abort
--More or (q)uit current module or to abort
802.11a AP Signal Strength Interval............ 60 seconds
Automatic Transmit Power Assignment
Transmit Power Assignment Mode................. AUTO
Transmit Power Update Interval................. 600 seconds
Transmit Power Threshold....................... -70 dBm
Transmit Power Neighbor Count.................. 3 APs
Min Transmit Power............................. -10 dBm
Max Transmit Power............................. 30 dBm
Transmit Power Update Contribution............. SNI.
Transmit Power Assignment Leader............... c4:64:13:8f:93:40
Last Run....................................... 75 seconds ago
Coverage Hole Detection
802.11a Coverage Hole Detection Mode........... Enabled
802.11a Coverage Voice Packet Count............ 100 packets
802.11a Coverage Voice Packet Percentage....... 50%
802.11a Coverage Voice RSSI Threshold.......... -80 dBm
802.11a Coverage Data Packet Count............. 50 packets
802.11a Coverage Data Packet Percentage........ 50%
802.11a Coverage Data RSSI Threshold........... -80 dBm
802.11a Global coverage exception level........ 25 %
802.11a Global client minimum exception lev.... 3 clients
Automatic Channel Assignment
Channel Assignment Mode........................ AUTO
--More or (q)uit current module or to abort
Channel Update Interval........................ 600 seconds [startup]
Anchor time (Hour of the day).................. 0
Channel Update Contribution.................... SNI.
Channel Assignment Leader...................... c4:64:13:8f:93:40
Last Run....................................... 75 seconds ago
DCA Sensitivity Level.......................... STARTUP (5 dB)
DCA 802.11n Channel Width...................... 20 MHz
DCA Minimum Energy Limit....................... -95 dBm
Channel Energy Levels
    Minimum...................................... unknown
    Average...................................... unknown
    Maximum...................................... unknown
Channel Dwell Times
    Minimum...................................... unknown
    Average...................................... unknown
    Maximum...................................... unknown
802.11a 5 GHz Auto-RF Channel List
    Allowed Channel List......................... 36,40,44,48,52,56,60,64
    Unused Channel List.......................... 100,104,108,112,116,120,124,
                                                  128,132,136,140
DCA Outdoor AP option.......................... Disabled
Radio RF Grouping
802.11a Group Mode............................. AUTO
--More or (q)uit current module or to abort
802.11a Group Update Interval.................. 600 seconds
802.11a Group Leader........................... c4:64:13:8f:93:40
    802.11a Group Member......................... c4:64:13:8f:93:40
802.11a Last Run............................... 75 seconds ago
802.11b Configuration
802.11b Network.................................. Enabled
11gSupport....................................... Enabled
11nSupport....................................... Enabled
802.11b/g Operational Rates
    802.11b/g 1M Rate............................ Mandatory
    802.11b/g 2M Rate............................ Mandatory
    802.11b/g 5.5M Rate.......................... Mandatory
    802.11b/g 11M Rate........................... Mandatory
    802.11g 6M Rate.............................. Supported
    802.11g 9M Rate.............................. Supported
    802.11g 12M Rate............................. Supported
    802.11g 18M Rate............................. Supported
    802.11g 24M Rate............................. Supported
    802.11g 36M Rate............................. Supported
    802.11g 48M Rate............................. Supported
    802.11g 54M Rate............................. Supported
802.11n MCS Settings:
    MCS 0........................................ Supported
    MCS 1........................................ Supported
    MCS 2........................................ Supported
    MCS 3........................................ Supported
    MCS 4........................................ Supported
--More or (q)uit current module or to abort
    MCS 5........................................ Supported
    MCS 6........................................ Supported
    MCS 7........................................ Supported
    MCS 8........................................ Supported
    MCS 9........................................ Supported
    MCS 10....................................... Supported
    MCS 11....................................... Supported
    MCS 12....................................... Supported
    MCS 13....................................... Supported
    MCS 14....................................... Supported
    MCS 15....................................... Supported
802.11n Status:
    A-MPDU Tx:
        Priority 0............................... Enabled
        Priority 1............................... Disabled
        Priority 2............................... Disabled
        Priority 3............................... Disabled
        Priority 4............................... Disabled
        Priority 5............................... Disabled
        Priority 6............................... Disabled
        Priority 7............................... Disabled
Beacon Interval.................................. 100
CF Pollable mode................................. Disabled
--More or (q)uit current module or to abort
CF Poll Request mandatory........................ Disabled
CFP Period....................................... 4
CFP Maximum Duration............................. 60
Default Channel.................................. 1
Default Tx Power Level........................... 0
DTPC Status..................................... Enabled
Call Admission Limit ........................... 105
G711 CU Quantum ................................. 15
ED Threshold..................................... -50
Fragmentation Threshold.......................... 2346
PBCC mandatory................................... Disabled
RTS Threshold.................................... 2347
Short Preamble mandatory......................... Enabled
Short Retry Limit................................ 7
Legacy Tx Beamforming setting.................... Enabled
Traffic Stream Metrics Status.................... Disabled
Expedited BW Request Status...................... Disabled
World Mode....................................... Enabled
Faster Carrier Tracking Loop..................... Disabled
EDCA profile type................................ default-wmm
Voice MAC optimization status.................... Disabled
Call Admision Control (CAC) configuration
   Voice AC - Admission control (ACM)............ Disabled
--More or (q)uit current module or to abort
   Voice Stream-Size............................. 84000
   Voice Max-Streams............................. 2
   Voice max RF bandwidth........................ 75
   Voice reserved roaming bandwidth.............. 6
   Voice load-based CAC mode..................... Disabled
   Voice tspec inactivity timeout................ Disabled
   Video AC - Admission control (ACM)............ Disabled
   Video max RF bandwidth........................ 50
   Video reserved roaming bandwidth.............. 0
802.11b Advanced Configuration
Press Enter to continue or to abort
802.11b Airewave Director Configuration
RF Event and Performance Logging
Channel Update Logging......................... Off
Coverage Profile Logging....................... Off
Foreign Profile Logging........................ Off
Load Profile Logging........................... Off
Noise Profile Logging.......................... Off
Performance Profile Logging.................... Off
Transmit Power Update Logging.................. Off
Default 802.11b AP performance profiles
802.11b Global Interference threshold.......... 10 %
802.11b Global noise threshold................. -70 dBm
802.11b Global RF utilization threshold........ 80 %
802.11b Global throughput threshold............ 1000000 bps
802.11b Global clients threshold............... 12 clients
Default 802.11b AP monitoring
802.11b Monitor Mode........................... enable
802.11b Monitor Channels....................... Country channels
802.11b AP Coverage Interval................... 180 seconds
802.11b AP Load Interval....................... 60 seconds
802.11b AP Noise Interval...................... 180 seconds
802.11b AP Signal Strength Interval............ 60 seconds
Automatic Transmit Power Assignment
Transmit Power Assignment Mode................. AUTO
Transmit Power Update Interval................. 600 seconds
Transmit Power Threshold....................... -70 dBm
Transmit Power Neighbor Count.................. 3 APs
Min Transmit Power............................. -10 dBm
Max Transmit Power............................. 30 dBm
Transmit Power Update Contribution............. SNI.
Transmit Power Assignment Leader............... c4:64:13:8f:93:40
Last Run....................................... 213 seconds ago
Coverage Hole Detection
802.11b Coverage Hole Detection Mode........... Enabled
802.11b Coverage Voice Packet Count............ 100 packets
802.11b Coverage Voice Packet Percentage....... 50%
802.11b Coverage Voice RSSI Threshold.......... -80 dBm
802.11b Coverage Data Packet Count............. 50 packets
802.11b Coverage Data Packet Percentage........ 50%
802.11b Coverage Data RSSI Threshold........... -80 dBm
802.11b Global coverage exception level........ 25 %
802.11b Global client minimum exception lev.... 3 clients
Automatic Channel Assignment
Channel Assignment Mode........................ AUTO
Channel Update Interval........................ 600 seconds [startup]
Anchor time (Hour of the day).................. 0
Channel Update Contribution.................... SNI.
Channel Assignment Leader...................... c4:64:13:8f:93:40
Last Run....................................... 213 seconds ago
DCA Sensitivity Level: ...................... STARTUP (5 dB)
DCA Minimum Energy Limit....................... -95 dBm
Channel Energy Levels
    Minimum...................................... unknown
    Average...................................... unknown
    Maximum...................................... unknown
Channel Dwell Times
    Minimum...................................... unknown
    Average...................................... unknown
    Maximum...................................... unknown
802.11b Auto-RF Allowed Channel List........... 1,6,11
Auto-RF Unused Channel List.................... 2,3,4,5,7,8,9,10,12,13
Radio RF Grouping
802.11b Group Mode............................. AUTO
802.11b Group Update Interval.................. 600 seconds
802.11b Group Leader........................... c4:64:13:8f:93:40
    802.11b Group Member......................... c4:64:13:8f:93:40
802.11b Last Run............................... 213 seconds ago
Mobility Configuration
Symmetric Mobility Tunneling (current) .......... Enabled
Symmetric Mobility Tunneling (after reboot) ..... Enabled
Mobility Protocol Port........................... 16666
Default Mobility Domain.......................... hosp
Multicast Mode .................................. Disabled
Mobility Domain ID for 802.11r................... 0x97e2
Mobility Keepalive Interval...................... 10
Mobility Keepalive Count......................... 3
Mobility Group Members Configured................ 1
Mobility Control Message DSCP Value.............. 0
Controllers configured in the Mobility Group
MAC Address        IP Address       Group Name                        Multicast
IP     Status
c4:64:13:8f:93:40 209.165.200.230 hosp                              0.0.0.0
        Up
Advanced Configuration
Probe request filtering.......................... Enabled
Probes fwd to controller per client per radio.... 0
Probe request rate-limiting interval............. 500 msec
EAP-Identity-Request Timeout (seconds)........... 30
EAP-Identity-Request Max Retries................. 2
EAP Key-Index for Dynamic WEP.................... 0
EAP Max-Login Ignore Identity Response........... enable
EAP-Request Timeout (seconds).................... 30
EAP-Request Max Retries.......................... 2
EAPOL-Key Timeout (milliseconds)................. 1000
EAPOL-Key Max Retries............................ 2
dot11-padding.................................... Disabled
Authentication Response Timeout (seconds)........ 10
Rogue Entry Timeout (seconds).................... 1200
AP Heart Beat Timeout (seconds).................. 30
AP Discovery Timeout (seconds)................... 10
AP Local mode Fast Heartbeat (seconds)........... disable
AP Hreap mode Fast Heartbeat (seconds)........... disable
AP Primary Discovery Timeout (seconds)........... 120
AP Primed Join Timeout (seconds)................. 0
Packet Forwarding watchdog timer (seconds)....... 240 (enable)
Location Configuration
RFID Tag data Collection......................... Enabled
RFID timeout.................................... 1200 seconds
RFID mobility.................................... Oui:00:14:7e : Vendor:pango S
tate:Disabled
Interface Configuration
Interface Name................................... management
MAC Address...................................... c4:64:13:8f:93:40
IP Address....................................... 209.165.200.230
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 209.165.200.1
External NAT IP State............................ Disabled
External NAT IP Address.......................... 192.168.1.1
VLAN............................................. untagged
Quarantine-vlan.................................. 0
Active Physical Port............................. 1
Primary Physical Port............................ 1
Backup Physical Port............................. Unconfigured
Primary DHCP Server.............................. 209.165.200.230
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
ACL.............................................. Unconfigured
AP Manager....................................... Yes
Guest Interface.................................. No
Interface Name................................... service-port
MAC Address...................................... c4:64:13:8f:93:41
IP Address....................................... 192.168.1.157
IP Netmask....................................... 255.255.255.0
DHCP Option 82................................... Disabled
DHCP Protocol.................................... Disabled
AP Manager....................................... No
Guest Interface.................................. No
Interface Name................................... virtual
MAC Address...................................... c4:64:13:8f:93:40
IP Address....................................... 1.1.1.1
DHCP Option 82................................... Disabled
Virtual DNS Host Name............................ Disabled
AP Manager....................................... No
Guest Interface.................................. No
WLAN Configuration
WLAN Identifier.................................. 1
Profile Name..................................... HOSP3C
Network Name (SSID).............................. HOSP3C
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Disabled
Network Admission Control
NAC-State...................................... Disabled
Quarantine VLAN................................ 0
Number of Active Clients......................... 0
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ management
WLAN ACL......................................... unconfigured
DHCP Server...................................... 209.165.200.230
DHCP Address Assignment Required................. Enabled
Quality of Service............................... Platinum (voice)
Scan Defer Priority.............................. 5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
IPv6 Support..................................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... 802.11b and 802.11g only
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
   Authentication................................ Disabled
   Accounting.................................... Disabled
   Dynamic Interface............................. Disabled
Local EAP Authentication......................... Disabled
Security
   802.11 Authentication:........................ Open System
   Static WEP Keys............................... Disabled
   802.1X........................................ Disabled
   Wi-Fi Protected Access (WPA/WPA2)............. Enabled
      WPA (SSN IE)............................... Disabled
      WPA2 (RSN IE).............................. Enabled
         TKIP Cipher............................. Enabled
         AES Cipher.............................. Enabled
      Auth Key Management
         802.1x.................................. Disabled
         PSK..................................... Enabled
         CCKM.................................... Disabled
         FT(802.11r)............................. Disabled
         FT-PSK(802.11r)......................... Disabled
FT Reassociation Timeout......................... 20
FT Over-The-Air mode............................. Enabled
FT Over-The-Ds mode.............................. Enabled
   CKIP ......................................... Disabled
   Web Based Authentication...................... Disabled
   Web-Passthrough............................... Disabled
   Conditional Web Redirect...................... Disabled
   Splash-Page Web Redirect...................... Disabled
   Auto Anchor................................... Disabled
   H-REAP Local Switching........................ Disabled
   H-REAP Learn IP Address....................... Enabled
   Infrastructure MFP protection................. Enabled
   Client MFP.................................... Optional
   Tkip MIC Countermeasure Hold-down Timer....... 60
Call Snooping.................................... Disabled
Band Select...................................... Enabled
Load Balancing................................... Enabled
Mobility Anchor List
WLAN ID     IP Address            Status
Press Enter to continue or to abort
Press Enter to continue or to abort
ACL Configuration
Press Enter to continue or to abort
CPU ACL Configuration
CPU Acl Name................................ NOT CONFIGURED
Wireless Traffic............................ Disabled
Wired Traffic............................... Disabled
RADIUS Configuration
Vendor Id Backward Compatibility................. Disabled
Call Station Id Case............................. lower
Call Station Id Type............................. IP Address
Aggressive Failover.............................. Enabled
Keywrap.......................................... Disabled
Fallback Test:
    Test Mode.................................... Off
    Probe User Name.............................. cisco-probe
    Interval (in seconds)........................ 300
MAC Delimiter for Authentication Messages........ hyphen
MAC Delimiter for Accounting Messages............ hyphen
Authentication Servers
Idx Type Server Address    Port    State     Tout RFC3576 IPSec - AuthMode/P
hase1/Group/Lifetime/Auth/Encr
Accounting Servers
Idx Type Server Address    Port    State     Tout RFC3576 IPSec - AuthMode/P
hase1/Group/Lifetime/Auth/Encr
--More or (q)uit current module or to abort
TACACS Configuration
Authentication Servers
Idx Server Address    Port    State     Tout
Authorization Servers
Idx Server Address    Port    State     Tout
Accounting Servers
Idx Server Address    Port    State     Tout
LDAP Configuration
Press Enter to continue or to abort
Local EAP Configuration
User credentials database search order:
    Primary ..................................... Local DB
Timer:
    Active timeout .............................. 300
Configured EAP profiles:
EAP Method configuration:
    EAP-FAST:
      Server key ................................
      TTL for the PAC ........................... 10
      Anonymous provision allowed ............... Yes
      Authority ID .............................. 436973636f00000000000000000000
00
      Authority Information ..................... Cisco A-ID
Press Enter to continue or to abort
HREAP Group Summary
HREAP Group Summary: Count: 0
Group Name                # Aps
Press Enter to continue or to abort
HREAP Group Detail
Press Enter to continue or to abort
Route Info
Number of Routes................................. 0
Destination Network          Netmask               Gateway
Press Enter to continue or to abort
Qos Queue Length Info
Platinum queue length............................ 100
Gold queue length................................ 75
Silver queue length.............................. 50
Bronze queue length.............................. 25
Press Enter to continue or to abort
Mac Filter Info
Press Enter to continue or to abort
Authorization List
Authorize MIC APs against AAA ................... disabled
Authorize LSC APs against Auth-List ............. disabled
Allow APs with MIC - Manufactured Installed C.... disabled
Allow APs with SSC - Self-Signed Certificate..... disabled
Allow APs with LSC - Locally Significant Cert.... disabled
Load Balancing Info
Aggressive Load Balancing........................ Disabled
Aggressive Load Balancing Window................. 5 clients
Aggressive Load Balancing Denial Count........... 3
Statistics
Total Denied Count............................... 0 clients
Total Denial Sent................................ 0 messages
Exceeded Denial Max Limit Count.................. 0 times
None 5G Candidate Count.......................... 0 times
None 2.4G Candidate Count........................ 0 times
Press Enter to continue or to abort
Dhcp Scope Info
Scope: PUNTOSAP
Enabled.......................................... Yes
Lease Time....................................... 86400 (1 day )
Pool Start....................................... 209.165.200.201
Pool End......................................... 209.165.200.229
Network.......................................... 209.165.200.0
Netmask.......................................... 255.255.255.0
Default Routers.................................. 0.0.0.0 0.0.0.0 0.0.0.0
DNS Domain.......................................
DNS.............................................. 0.0.0.0 0.0.0.0 0.0.0.0
Netbios Name Servers............................. 0.0.0.0 0.0.0.0 0.0.0.0
Press Enter to continue or to abort
Exclusion List ConfigurationUnable to retrieve exclusion-list entry
Press Enter to continue or to abort
CDP Configuration
Press Enter to continue or to abort
Country Channels Configuration
Configured Country............................. ES - Spain
      KEY: * = Channel is legal in this country and may be configured manually.
           A = Channel is the Auto-RF default in this country.
           . = Channel is not legal in this country.
           C = Channel has been configured for use by Auto-RF.
           x = Channel is available to be configured for use by Auto-RF.
         (-,-) = (indoor, outdoor) regulatory doamin allowed by this country.
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
    802.11bg     :
    Channels     :                   1 1 1 1 1
                 : 1 2 3 4 5 6 7 8 9 0 1 2 3 4
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-
ES (-E   ,-E   ): A * * * * A * * * * A * * .
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
    802.11a      :                         1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
    Channels     : 3 3 3 4 4 4 4 4 5 5 6 6 0 0 0 1 1 2 2 2 3 3 4 4 5 5 6 6
                 : 4 6 8 0 2 4 6 8 2 6 0 4 0 4 8 2 6 0 4 8 2 6 0 9 3 7 1 5
-----------------:+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-
ES (-E   ,-E   ): . A . A . A . A A A A A * * * * * * * * * * * . . . . .
Press Enter to continue or to abort
WPS Configuration Summary
Auto-Immune
Auto-Immune.................................... Disabled
Client Exclusion Policy
Excessive 802.11-association failures.......... Enabled
Excessive 802.11-authentication failures....... Enabled
Excessive 802.1x-authentication................ Enabled
IP-theft....................................... Enabled
Excessive Web authentication failure........... Enabled
Signature Policy
Signature Processing........................... Enabled
Press Enter to continue or to abort
Custom Web Configuration
Radius Authentication Method..................... PAP
Cisco Logo....................................... Enabled
CustomLogo....................................... None
Custom Title..................................... None
Custom Message................................... None
Custom Redirect URL.............................. None
Web Authentication Type.......................... Internal Default
External Web Authentication URL.................. None
Configuration Per Profile:
Rogue AP Configuration
Rogue Location Discovery Protocol................ Disabled
Rogue on wire Auto-Contain....................... Disabled
Rogue using our SSID Auto-Contain................ Disabled
Valid client on rogue AP Auto-Contain............ Disabled
Rogue AP timeout................................. 1200
MAC Address        Classification     # APs # Clients Last Heard
Adhoc Rogue Configuration
Detect and report Ad-Hoc Networks................ Enabled
Auto-Contain Ad-Hoc Networks..................... Disabled
Client MAC Address Adhoc BSSID         State              # APs   Last Heard
Rogue Client Configuration
Validate rogue clients against AAA............... Disabled
Rogue Client Configuration
Validate rogue clients against AAA............... Disabled
--More-- or (q)uit
MAC Address        State              # APs Last Heard
Ignore List Configuration
MAC Address
Rogue Rule Configuration
Priority Rule Name               State    Type          Match Hit Count
(Cisco Controller) >show sysinfo
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 6.0.199.4
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console
1.27
Build Type....................................... DATA + WPS
System Name...................................... CISCO-CAPWAP-CONTROLLER
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 209.165.200.230
Last Reset....................................... Power on reset
System Up Time................................... 0 days 0 hrs 41 mins 2 secs
System Timezone Location......................... (GMT +1:00) Amsterdam, Berlin,
Rome, Vienna
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... ES - Spain
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +39 C
External Temperature............................. +23 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Disabled
Number of WLANs.................................. 1
3rd Party Access Point Support................... Disabled
Number of Active Clients......................... 0
Burned-in MAC Address............................ C4:64:13:8F:93:40
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 25
(Cisco Controller) >
The AP log
AP442b.03dc.0925>
*Apr 19 23:10:18.428: %CAPWAP-3-ERRORLOG: Selected MWAR 'CISCO-CAPWAP-CONTROLLER
'(index 0).
*Apr 19 23:10:18.428: %CAPWAP-3-ERRORLOG: Go join a capwap controller
logging facility kern
        ^
% Invalid input detected at '^' marker.
logging facility kern
        ^
% Invalid input detected at '^' marker.
*Apr 19 23:10:19.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 209.165.200.230 peer_port: 5246
*Apr 19 23:10:19.001: %CAPWAP-5-CHANGED: CAPWAP changed state to
*Apr 19 23:10:20.200: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 209.165.200.230 peer_port: 5246
*Apr 19 23:10:20.201: %CAPWAP-5-SENDJOIN: sending Join Request to 209.165.200.23
0
*Apr 19 23:10:20.201: %CAPWAP-5-CHANGED: CAPWAP changed state to JOIN
*Apr 19 23:10:20.211: %CAPWAP-3-ERRORLOG: This AP is not supported in controller
version 6.0.199.4 ---->What's mean that? Is it compatible the ap with the WLC? ¿Es compatible el AP con el WLC?
*Apr 19 23:10:20.354: %CAPWAP-5-CHANGED: CAPWAP changed state to CFG
*Apr 19 23:10:20.355: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 209
.165.200.230:5246
*Apr 19 23:10:20.356: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Apr 19 23:10:20.356: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Apr 19 23:10:20.412: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is
not established

Managing remote C800 with the wireless controller

We have a number of regional offices throughout the country with a C800 as the Internet facing router and it is also our wireless.
We have a Cisco wireless controller in the Data Center an we need to manage\monitor all the C800, but the problem is that those remote sites
are not VPN'd nor part of our WAN network.
Which setup do you
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin:0in;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;}
recommend:
1) 1) WLC to monitor the C800 using its public IP address
1) 2) Create a VPN tunnel from each of the remote sites to our data center and only allow wireless to go through for mgmt purposes
anany other options?
T

First question is which 800 do you have ? there's like 20 different versions out there.
If you talk about WLC, I would suppose you have something like the 880 ?
I'm afraid the WLC will need the internal AP ip address. So you would need to do so reverse nat to direct public ip address tarffic on capwap ports to the internal AP.
This or the VPN tunnel.
Nicolas
===
Don't forget to rate answers that you find useful

Wireless Guest Access with 802.1X (PEAP/MSCHAPv2) and ISE?

Hi,
I have a setup based on WLC 5508, Catalyst 3750-X and AP3600i.
The WLCs are running 7.3 and ISE is 1.1.1
I'm trying to setup wireless guest access, where the guests connect to a SSID with 802.1X using PEAP/MSCHAPv2.
They should receive their username/password either from a sponsor directly (corporate AD user which prints the credentials) or through a SMS.
The credentials will be created by the sponsor, using the sponsor portal on the ISE.
Now to the questions:
Is it correct that the foreign WLC (i.e. the WLC within the internal corporate network), should be set to no L2 and L3 security on the guest WLAN, to avoid having the foreign WLC contact the ISE and all traffic be forwarded directly to the anchor WLC?
Is it correct that the anchor WLC (i.e. the WLC in the DMZ), should be configured with 802.1X/WPA2 L2 security and the ISE servers as the RADIUS servers on the guest WLAN, to ensure that the client is correctly authenticated/authorized by the ISE?
When a guest logs on, how can I ensure that only one device (MAC address) is allowed per user?
As it is now, a guest is able to log on with (I assume) an unlimited number of devices, using the credentials they have received.
Thankyou very much :-)
Best Regards,
Niels J. Larsen

Hi,
I have a setup based on WLC 5508, Catalyst 3750-X and AP3600i.
The WLCs are running 7.3 and ISE is 1.1.1
I'm trying to setup wireless guest access, where the guests connect to a SSID with 802.1X using PEAP/MSCHAPv2.
They should receive their username/password either from a sponsor directly (corporate AD user which prints the credentials) or through a SMS.
The credentials will be created by the sponsor, using the sponsor portal on the ISE.
Now to the questions:
Is it correct that the foreign WLC (i.e. the WLC within the internal corporate network), should be set to no L2 and L3 security on the guest WLAN, to avoid having the foreign WLC contact the ISE and all traffic be forwarded directly to the anchor WLC?
Is it correct that the anchor WLC (i.e. the WLC in the DMZ), should be configured with 802.1X/WPA2 L2 security and the ISE servers as the RADIUS servers on the guest WLAN, to ensure that the client is correctly authenticated/authorized by the ISE?
When a guest logs on, how can I ensure that only one device (MAC address) is allowed per user?
As it is now, a guest is able to log on with (I assume) an unlimited number of devices, using the credentials they have received.
Thankyou very much :-)
Best Regards,
Niels J. Larsen

802.1x and Windows Domain Controller with ACS

Wow, I am having a tough time getting my ACS and the Domain controller to work with 802.1x PEAP. Can somebody explane to me how to set up the domain controller (Active directry) to get a PEAP cert? Some other questions. If I am using PEAP and 802.1x how does my computer get a cert. from the CA if the port is disabled by 802.1x? And How do I set up my domain controller to work with ACS to authenticate users. I have been beating my self to death to figure this out. Any help would be ausome. I am really stuck on trying to make this work.
Thanks a ton in advance
Justin

I as a Cisco customer would like to see answers to our questions based on some real world experience or something you've noticed in a lab environment.
By simply posting links is not very helpful. The reason most of us come to this site and post our questions, is because we already went to the Cisco website and found the explanation to be vague. In the future, please post answers to our question, intead of referring us to a link.
Thank you,
John...

802.1x wireless authentication with certificates

Hi.
I have configured and working 802.1x authentication with certificates for Wired connections. with no problem.
when i try to authenticate the same machine with 802.1x and certificates , on Wirelss, the ACS rejects it with:
"12520 EAP-TLS failed SSL/TLS handshake because the client rejected the ACS local-certificate."
the ACS is the same, the certificate the same, and the root ca is the same.
what's hapenning????
Antero Vasconcelos

What supplicant are we using for wireless authentication? Do we have complete chain of certificates installed on the client machine? Can you check if we have root CA/intermediate correctly installed in client and ACS.
~BR
Jatin Katyal
**Do rate helpful posts**

Wireless Controller with 802.1x

Similar Messages

Maybe you are looking for