Wireless does not work after chaning my router

I have HP P1102W laser jet printer.
The wireless feature worked fine until I recently changed my internet router(from linksys to cisco), and now I can't seem to get the wireless connection with my printer.
I tried reinstalling the printer using the CD-rom but to no avail. 
What can I do to get the wireless connection back?

Hi,
Thank you for posting you query,
In order to resolve the issue, please make sure the printer is placed closer to the router and uninstall the printer drivers already installed and then start the instalaltion and seelct teh connection type as wireless network. Then select use USB to configure wireless and when prompted conenct the USB cable and then select the network and enter the encryption key follow the onscreen  instructions.
If the issue still persisits, please open the browser and in the address bar enter the IP address of the router and click on GO. This will take you to the router configuration page. On the router page, please click on Wireless Setup  and please make sure SSID Broadcast is enabeld and the Wireless Mode is set to Mixed or 802.11 B/G/N and the Wireless Channel is set to 11 and click on Apply. Then try to connect the printer to the network by using the CD.
Say "Thanks" by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as "Accepted Solution"
(Although I am employed by HP, I am speaking for myself and not for HP)

Similar Messages

  • EPrint does not work after new wifi router on Verizon DSL

    I have been using ePrint on my iPod, iPad, and iPhone for a few months without a problem, but recently had to switch to a new wifi router on my Verizon DSL, as my wifi kept turning off and Verizon's solution was an updated wifi router. Since the switch, I cannot ePrint from my mobile devices. I can, after reconfiguration, print from my laptops. The ePrint app still finds the Deskjet 3050a, says "sending to printer", but will not print. The ePrint is turned on. I tried to delete the app and reinstall in hopes that I can start fresh, but it still does not work. I tried to add a new printer, with the email supplied on the ePrint screen on the printer, but nothing.
    Any ideas?

    Hi Honor Student
    Is your printer connected to the new router as it sounds like it is still looking for the old one ?  Maybe  just disconnect it and reconnect it again to your new router and then the ePrint APP should pick it up.
    I work for HP.
    Thanks
    Caroline
    Although I am a HP employee, I am speaking for myself and not for HP.

  • HP 5524 Wireless does not work after firmware upgrade

    HI,
    I have just purchased an HP5524.  After initial problems setting up the WPA key from the printer screen, I connected via USB, found the printer and swapped to wireless successfuly. I then installed the printer software on all my computers at home successfully over wireless.
    The printer then needed a firmware upgrade to support eprint (?), which is successfully connected, downloaded the fireware, installed and went through the boot cycles successfully. 
    However, ever since wireless will not work.  Before I return it to the retailer as "not fit for purpose" I thought I would ask the forum.  The diagnostics downloaded a tool, which I went through, but this did not offer solutions that I had not already tried.
    Thank you

    Hi,
    Thank you for posting you query,
    In order to resolve the issue, please make sure the printer is placed closer to the router and uninstall the printer drivers already installed and then start the instalaltion and seelct teh connection type as wireless network. Then select use USB to configure wireless and when prompted conenct the USB cable and then select the network and enter the encryption key follow the onscreen  instructions.
    If the issue still persisits, please open the browser and in the address bar enter the IP address of the router and click on GO. This will take you to the router configuration page. On the router page, please click on Wireless Setup  and please make sure SSID Broadcast is enabeld and the Wireless Mode is set to Mixed or 802.11 B/G/N and the Wireless Channel is set to 11 and click on Apply. Then try to connect the printer to the network by using the CD.
    Say "Thanks" by clicking the Kudos Star in the post that helped you.
    Please mark the post that solves your problem as "Accepted Solution"
    (Although I am employed by HP, I am speaking for myself and not for HP)

  • Wrt610n wireless network does not work after firmeware upgrade

    Hi
    I just updated my Wrt610n hardware version 1 to the newest firmware, it did finish with sucess, I did factory reset reboot and reconfig. But the wireless network does not work , cant connect computers to it. Did downgrade the firmware to the same it was and restore my settings but still wireless does not work. But router works fine with lan.  Any suggestions? maybe the firmware tosted the router?
    Regards
    Stefan

    Update -
    After last reset and reupgrade with the newest firmware for hardware version 1 I could config the router and connect 2 computers with wireless - but only for about 15 mín - then they lost connection and could not reconnect.
    I did then get the newest update for hardeware version 2 - just to try and upgraded with that and got success, and now I have reset the router again and config it and those 2 computers are connected and have been for 1 hour now. So seems to be working - is it okay to have the firmware for hardware version 2 on my version 1 router?
    Any thought what is going on - could it be that the other firmware had not loaded compleytle or?

  • PCI wireless card does not work after restart - FM2-A55M-E33

    Installed TP-LINK WN751ND wireless PCI card onto FM2-A55M-E33 motherboard. The card works fine after cold start, but does not work after restart. Windows recognises the card, but it gets code 10, cannot start.
    BIOS is updated (v.11.1), as well as drivers and Windows 7 64.
    I suspect that this might be the issue: Incorrect ASPM Transitions on the GPP Interface as found in ChipsetMotherboard_TechDocs/48671.pdf on AMD's official support site.
    Does anyone know more about this issue?

    Great! I've done that and now my card shows up. Thing is, when I try to get an IP address, it won't work. Here is the command output:
    ieee80211 phy0: wl_ops_config: change monitor mode: false (implement)
    ieee80211 phy0: wl_ops_config: change power-save mode: false (implement)
    ieee80211 phy0: wl_ops_bss_info_changed: qos enabled: false (implement)
    And then it times out and no IP is assigned. The thing is, wpa_supplicant stays alive after this time out, and I am unable to kill it (killall -9 wpa_supplicant won't kill it). At this point if I try to reboot the machine, it will stop at 'Rebooting' and won't go anywhere. If I turn off the wireless card in its switch Linux crashes. If I try to get an ip again (by running dhcpcd) the command will hang and not return to the shell anymore.
    I am unable to find any useful information in the logs.
    Got any more suggestions?
    Thanks! (And sorry to disturb so much)

  • My sound system does not work AFTER installing pc to tv wireless connection

    my sound system does not work after installing hp pc to tv wireles device when I am using lap top for other purposes.

    Hi,
    You don’t install VS2010 on the client PC, then where did the Form Invoice not work? When you run it from another version of VS? Or when you run the application with application.exe?
    Based on your description, one form works well, another form does not. I assume that two forms are in two different projects, then please check the .Net Framework used by the two projects. If they are different, you can use the
    one used by the Form contact for Form Invoice.
    Because this issue is a project issue, I recommend you to consult it on some application forum such as Windows Forms General forum for better support.
    VS General Question forum mainly discusses
    the usage of Visual Studio IDE such as
    WPF & SL designer, Visual Studio Guidance Automation Toolkit, Developer Documentation and Help
    System and Visual Studio Editor.
    Thanks,
    We are trying to better understand customer views on social support experience, so your participation in this interview project would be greatly appreciated if you have time. Thanks for helping make community forums a great place.
    Click
    HERE to participate the survey.

  • Satellite A110-228 LAN does not work after hibernate

    Well, subject says it all, really. The LAN (wired) network does not work after hibernate.
    It seems it cannot find the DHCP server, so after a while it gets a 169.* address.
    After a reboot, the network functions as usual (gets a IP address from the DHCP server)
    Tried the usual things, disconnecting the cable, disabling the LAN device, battery or AC adapter, the behavior is reproducible.
    The wireless network will be restored after a hibernate.
    It needs a little help though (right click on the icon and "recover" or whatever it is called in English)
    Any suggestions?
    Wilm Boerhout

    Hi guys
    In the Toshiba HW setup which is placed in the control panel the options Wake-up on LAN and Built-in LAN should be enabled.
    I think the options are disabled by default.
    Furthermore the default setting for Wake on Settings is OS controlled. To use the Wake-up on LAN function under power off mode, in the device driver for the network card under the menu point Wake On Settings the Value Wake on Magic & Directed must be set.
    Please check this how to enable WOL (first time use):
    1. Go to [Start] -> [Control Panel] -> [Toshiba HWSetup] -> [LAN] tab
    2. Enable Wake-up on LAN
    3. Click [Apply]. System will request to reboot.
    4. After the reboot go to [Start] -> [Control Panel] -> select [System]
    5. On system properties dialog box select [Hardware] tab -> click [Device manager]
    6. On Device manager dialog box select [Networking adapters] -> double click [Intel(R) PRO/100 VE Network Connection]
    7. Go to [Advanced] tab -> select [Wake On Settings] property -> Select [Wake on Magic & Directed]
    8. Press [OK] to close the dialog box.

  • Card slot does not work after update (14/10/2011)

    Card slot does not work after yesterday update (14/10/2011)! It works with my SD card month ago, but now it dosn't!!!
    MacBook Pro 13 OS ver. 10.6.8

    Thanks for your suggestion. I downloaded OnyX and ran the cleaning function. After restarting, I opened Help and once again the first screen appeared fine. But again most of the links did not work, though those under the "What's New" heading did work. I might add that I had previously tried a variety of suggestions posted in another thread, which included deleting from the caches folder in Home>Library several files such as com.apple.helpui and help.plist in the Preferences folder. (As noted in my previous post this evening, I also created another user but that also did not have any effect.) Any other ideas? Thanks

  • HT1688 My Hot Spot does not work after update to 6.0.1.  Service is with ATT.  Apple says problem is with ATT, ATT says problem is with Apple.  Anyone else having this problem?

    My Hot Spot does not work after update to 6.0.1.  Any suggestions?

    Ok, I had the same issue, my phone is unlocked(iphone 5 with 6.1.3). So I went to the apple store and had it replaced. it worked good for a day and started doing the same thing. When the apple tech replaced my phone, he transfered my screen protector to the new one.
    so I thought it was my sim card, I put in my sisters sim card from a different carrier and it did the same, so then I was like let me take off the screen protector, and that was it.
    so guys, if you have a screen protector on your phone and it's doing "low signal", "No Service", "Searching", "Full bars cycle" then take off the screen protector. so far my phone is working normal.

  • Click to activate does not work after update

    Click to activate plugin does not work after updating to version 23.0.1

    hello Kamullia, if you have set click-to-play to true in about:config you can now go to the ''addons-manager > plugins'' section and set the permissions individually for each plugin type.

  • WiFi iPhone 4S does not work after update iOS 6.0

    WiFi iPhone 4S does not work after update iOS 6.0

    This sounds more like a hardware issue.
    Have you checked that the dock connector port is not dirty?

  • Flash player does not work after I installed it

    Flash player does not work after I installed it

    I'm using Mac Osx and my browser is Safari
    Date: Wed, 5 Feb 2014 00:41:29 -0800
    From: [email protected]
    To: [email protected]
    Subject: Flash player does not work after I installed
        Re: Flash player does not work after I installed it
        created by Mike M in Installing Flash Player - View the full discussion
    This is a user-to-user forum, NOT 24/7 support. You're "lucky" I happen to be up at 1:40 am to answer you.
    What OS are you using?
    http://mmonlinedesigns.com/images/os.png
    What browser?
    http://mmonlinedesigns.com/images/browsers.png
         Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at http://forums.adobe.com/message/6087541#6087541
         Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: http://forums.adobe.com/message/6087541#6087541
         To unsubscribe from this thread, please visit the message page at http://forums.adobe.com/message/6087541#6087541. In the Actions box on the right, click the Stop Email Notifications link.
               Start a new discussion in Installing Flash Player at Adobe Community
      For more information about maintaining your forum email notifications please go to http://forums.adobe.com/thread/416458?tstart=0.

  • Apple TV does not work after trying to update software. Main light keeps blinking and on the screen shows itunes icon and a usb cable. What does that means?

    My Apple TV does not work after trying to install the new software update. The main light keeps blinking rapidly and on the screen it shows the itunes icon and a USB cable. What does that mean?

    The Apple TV is in recovery mode. Try to restore the Apple TV. Follow the link for instructions on the restore process.
    http://support.apple.com/kb/HT4367

  • IMessage does not work after upgrade to iOS 8.1.3 to my iPad 4

    iMessage does not work after upgrade to iOS 8.1.3 on my iPad 4

    I Fixed it by trying to sign in with a different ID and canceling when it asked For a password and then signed in with my ID and it works! No more error message. I got this idea from another discussion. Thank you for replying though.

  • "F11 System Recovery" during boot does not work after Cloning hard drive.

    Problem: “F11 System Recovery” during boot does not work after Cloning hard drive.
    HP Envy m6-1125dx UEFI Notebook Computer with GPT hard drive.
    Original Seagate Hard Disk GPT 700GB with Window 8.0_64 upgraded to Windows 8.1_64
    Startup Menu (F11 System Menu works properly) only on original hard drive.
    Following obtained from Disk Management & diskpart in Command Prompt.
                                     GPT Disk <700GB>
    Partition 1 WINRE NTFS Primary 235MB/400MB [Recovery]
    Partition 2 EFI System FAT32 (LBA) Primary 108MB/260MB [System]
    Partition 3 (NONE) Unformatted Primary 128MB/128MB [Reserve]
    Partition 4 Main NTFS Primary 90GB/195GB [Primary “C”]
    Partition 5 (NONE) NTFS Primary 372MB/450MB [Recovery]
    Partition 6 Data NTFS Primary 7GB/475GB [Primary “E”]
    Partition 7 NTFS Primary 26MB/350MB [Recovery]
    Partition 8 Recovery NTFS Primary 24GB/26GB [Recovery “D”]
    I have Cloned the original hard drive to a new HGST 1TB Hard Drive using four different methods (sector by sector):
    Acronis True Image 2015
    Acronis Backup for PC
    AOMEI Backupper Professional
    Macrium Reflect
    Each time the cloning process completes successfully and has the same original partition arrangement. The computer works properly except when trying to use the “F11 System Menu” key during boot. It gives the following error message:
    “Recovery
    Your PC needs to be repaired
    A required device isn’t connected or can’t be accessed.
    Error code: 0xc0000225
    You need to use the recovery tools on your installation media. If you don’t have any installation media (like a disc or USB device), contact your system administrator or PC manufacturer. “
    Any suggestions why the F11 System Recovery does not work during boot and how to fix the problem would be appreciated. I have does various disk checking and file checking on both the original and new hard drive with no errors.
    Thank you in advanced.

    Hi,
    How did you clone the HDD ? One-for-one or different method ?
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Maybe you are looking for