Wireless HP Printer on Dual Band Airport Extreme Base Station

I'm looking to upgrade my router to the dual band AEBS. I'll end up with some n machines and some g machines, including a wireless HP printer. Will my n-enabled machines be able to print to the g wireless printer on the g network?
Thanks,
JD

+Will my n-enabled machines be able to print to the g wireless printer on the g network?+
Yes. All devices will receive an IP address from the AirPort Extreme, so they will all be on the same network and will be able to communicate with each other. This is true even if you have a wired only computer connected to the AirPort Extreme. It will be able to print to the printer.
But, if you enable the Guest network features, computers on this network will not be able to "see" other computers or connect to any devices on the main network.

Similar Messages

Why does the new Dual-Band AirPort Extreme Base Station act as a proxy?

The previous thread
http://discussions.apple.com/thread.jspa?threadID=1531675
has been archived and nothing came of it, but after testing, I'm certain that their findings are true.
The Dual-Band AirPort Extreme Base Station (AEBS) with firmware 7.4.1 acts as a proxy for TCP ports 21, 554, and 7070 when NAT is turned on. This can be verified by using Nmap on any external server known to NOT have the ports open and having Nmap return that the ports are open. You can telnet to these ports to verify that they're "open," even though they are not on the server.
This functionality appears to be undocumented and as far as I can tell, the only way to turn it off is to put the AEBS into bridge mode and having some other device do NAT further upstream.
As a computer professional, this functionality extremely undesirable, particularly since it is not documented and doesn't have an "off switch." I wasted a bunch of time with one of my network engineers because of this, thinking that some network router was spoofing our server. I also wasted a bunch of my time trying to detect whatever "stealthy rootkit" had opened a FTP server and some other botnet related ports on our server, when in reality, it was simply my AEBS tricking me.
Disabling NAT-PMP ("Enable NAT port mapping protocol") does not affect this.
Is it too much to ask to have a checkbox in the "Advanced" section of the AirPort Utility to turn this feature off?

Welcome to the discussions forum Michael Bennett2.
Thanks for investigating this odd behavior.
If you want your work to be noticed by those who can effect change, you'll have to tell Apple via their feedback link. It won't do any good to post it here.
http://www.apple.com/feedback/

Wirelessly Connecting HP Laserjet P3015 to Airport Extreme Base Station

Hi, I just purchased a new Airport Extreme Base Station, and was able to establish an internet connection to it. I'd like to find out if it's possible to connect the HP Laserjet Enterprise P3015 to the Extreme, wirelessly rather than via a USB Cable. I've looked at the HP page for this printer, but I'm baffled by all the lingo. I believe it's a newer model of HP printer (or maybe it isn't?) but I bought it new from HP recently.
http://h20000.www2.hp.com/bizsupport/TechSupport/DocumentIndex.jsp?contentType=S upportFAQ&lang=en&cc=us&docIndexId=64178&taskId=101&prodTypeId=18972&prodSeriesI d=3815797&printver=true#10
Is there a term for the type of printer that can be wirelessly connected? Should the printer, by default, give off a signal that I can pick up? I don't see anything popping up in Airport Utility 6.3
I'm using OS10.7.5 by the way.
I'm off to post a message on the suitable HP forum (if I can find it ) but I'm so used to the Apple Community knowing what's what, that I was hoping that some kind soul here might just have experience with this.
Thank you.
PS. From what I can understand from the "Trouble-shooting FAQ," wireless printing is possible, but I just don't see an option for syncing it up with a MAC? Maybe it only works with Windows?

wuzradioman
I don't see where the P3015 printer is wifi capable. Therefor, you cannot use wifi to directly communicate with it.
Thanks for the reply Wuzradioman. I dug around (several) of HP's sites and it looks like the info was slightly different for the same printer listed on both the Home and Business sites. I did find a link on a 3rd HP page (which I've since misplaced!) that indicates that the P3015 requires a wireless card to be installed. But when I clicked the link for "accessories and additional hardware" a link to the card was nowhere to be found. I'll try to dig up that link in the event that some other poor soul has the same printer and a similar question.
Vernon Alexander
I find the HP printers (they're called wireless printers by the way) to be cumbersome to connect wirelessly. there's a lot of manual work involved that can be time-consuming. For example, I found it incredibly irritating to enter the wireless access passcode.
Thanks for the reply. After talking to some other people, this seems to be the consensus on wireless printing. I guess there's a reason, esp. in enterprise environments, that printers are often hard-wired.
Bob Timmons
you can run an Ethernet cable over a much longer distance than a USB cable, so Ethernet might be the best option, and the one I would prefer.
As far as wireless, If you connected an AirPort Express to the printer and disguised it near the printer, then you could locate the printer anywhere you want and have it connect using wireless to the network.
Instead of installing a wireless "card" inside the printer, you use an outboard device to accomplish the same task.
Thanks Bob. I did end up hooking up via a Cat-5e cable from printer to Airport Extreme base. Previously, I had the printer hooked up via USB cable (at a shorter distance) to my Airport Express, which the Extreme now replaces.
Unfortunately, I can't seem to get the HP Laserjet P3015n printer recognized after having connected it via Cat5e cable to the Airport Extreme. 1) there's still somethign about it being attached to the old Airport Express (which is now used to extend my network. 2) The P3015 is identified as a P3010 - which is a carry-over from when I had originally set up the printer on my (then) main base station which was the Airport Express. I didn't (or rather "stopped") questioning the fact that the P3015 was recognized as a P3010 just because it was the only way I could get the printer to be recognized at the time.\\
But I suppose this new challenge merits a separate thread, which I'll start after I do a search of the support forums. Maybe there's something obvious I'm not doing to get the printer sorted out.

Printer that works with Airport Extreme Base Station

Hi. We are very new to Macs (2 weeks). Have a Mac Book and AEBS. Both work fine. Our HP printers, however, only work if connected directly to the Mac Book. I'm informed that we need to get a printer that works with the AEBS if we wish to have wireless printing. If anyone can recommend a printer that works with AEBS, we'd be grateful. Thanks.

Hello Jungle-cat. Welcome to the Apple Discussions!
Check out the following iFelix site to see which printers are known to work (not not) with the new 802.11n AirPort Extreme Base Station (AEBSn).

Recognizing a printer attached to an Airport Extreme Base Station

I have attached a printer to the usb port of my airport extreme base station. The printer is recognized by two of my MacBook Pros running Mac OS X version 10.4.11. However, it is not recognized by my latest MacBook Pro running 10.5.2. Is this a problem with the new system, or is there another reason? I have, of course, made sure that the printer drivers are installed, and the printer attached to the Airport works with the new MacBook Pro when connected directly through a usb port on the laptop. Any help will be gratefully received!!

samandlily wrote:
I have something related to this topic going on. I have an Epson printer on my Airport Extreme via a USB. Just recently when I try to print from my iMac, I get a message saying that "the Airport Network is busy, and it will try again in 10-20 seconds". Then nothing happens and the document will not print. Any ideas what is going on?
Please do not pollute the OP's thread by posting here. You are clearly experiencing a different problem - different symptoms, different version of OS X, different printer - and will get much better help if you start your own thread because your problem will get lots more attention that way.
- cfr

Printer not found on airport extreme base station

Have set up a printer via the USB port on the base station it worked just fine BUT when I switch off the printer and my mac book pro and then restart the printer is no longer avialable / picked up by the base station. I have to restart the base station via the airport utility and then it finds the attached printer. Is this what you have to do?

I've had mine totally not work either upon restart. Basically - I've had two of these basestations lose their usb drives and printers when restarted. Its like they blow a fuse or something.

Streaming DVD movies over Dual Band Airport Extreme Airdisk

Hello,
This is my first post in the discussion forums. I have been a long time reading of the discussion forums. I recently bought a late 2009 dual band Airport Extreme base station. I have been trying to stream DVD movies (TS_VIDEO) using the Airdisk feature. What I did, as an experiment, was to hook up the dual band Airport Extreme to my 2009 Mac-Mini using an ethernet cable from the base station to the Mac-Mini. I enabled file sharing on the Airport extreme base station. I hooked an external hard drive to the base station via a USB port on the base station. I mounted the Airdisk on the Mac-MIni. When I play the ripped DVD movies (TS_VIDEO) from the Airdisk I get a lot of stuttering using Front-Row. According to the Apple customer service reps, this is normal behavior. Can anybody comment on if this is normal behavior.

An uncompressed DVD should have a maximum data rate of around 6 or 7 Mbps and so be well within the nominal 300 Mbps of an 802.11n network - even allowing for the slower actual speeds attained due to networking overheads and weak signals. However, given that you have the latest Airport Extreme it sounds like you may be suffering from the common fault many are reporting in these forums, in which disk transfer rates are very, very slow over the 5GHz 802.11n connection. Look at some of the other threads here. It is clearly a fault in the current design (not a fault with your particular unit) and something that Apple are apparently aware of. Most are hoping it will be resolved in an updated firmware at some point in the future.
Edit: I just re-read your post and notice that you said you used a physical connection between the Airport and the Mac Mini. Thus no wireless involved. Nevertheless, others have reported poor data rates with disks connected to the unit, and so this may still be the issue. Check out some of the other threads here.
Message was edited by: Paul Howland2

Airport Extreme Base Station Wireless Woes

Hi,
I just bought this dual band Airport Extreme Base Station on 3/10/2010. After I setup the Airport, I have difficulties connecting my iphone 3GS to the base station. My iphone 3GS is able to see the wireless network but not able to join it. Only my macbook pro is able to connect wirelessly. My windows PC and iphone 3GS could not.
I wonder whats could be the problem?
Some logs from the base station:
Oct 06 23:00:04 Severity:5 Associated with station <mac address of iphone 3GS>
Oct 06 23:00:04 Severity:5 Installed unicast CCMP key for supplicant <mac address of iphone 3GS>
Oct 06 23:00:04 Severity:5 Disassociated with station <mac address of iphone 3GS>
Oct 06 23:00:04 Severity:5 Rotated TKIP group key.
Setting of Airport Extreme Base Station:
Wireless Security: WPA/WPA2
Wireless Channel: Auto
Creating a new network
Things I have tried:
1) Changing the wireless channel
2) Removing the wireless security
Thanks

I think I manage to find the problem on why my airport extreme keep on dropping connection.
This is my connection.
Cable Modem -> Airport Extreme -> Aztech Gigabit Homeplug 1-> Aztech Gigabit Homeplug 2 -> Dlink DIR-825.
When I plug out the conenction from Airport Extreme to Aztech Gigabit Homeplug 1, I am able to connect to the wireless using iPhone 3GS. Once I plug back the connection and do a refresh the iPhone 3GS wifi connection, I am not able to connect the wireless.
Hmm, anyone faces the same problem?

Several PC and Mac connectivity issues with Airport Extreme Base Station

Hello,
This is not all necessarily airport base station related, but there is some crossover, so I'm posting all of these issues...
Here is the laundry list of things that I can't make work in a home network that contains a PC w/ XP Home, MacBook 1.83 w/ 10.4.7, and Airport Extreme Base Station w/ Modem.
1. Can't see the PC from the Mac.
a. "Connect to server -> Browse" does not find the PC
b. "ipconfig" on PC provides valid looking IP address
c. ping from mac to PC IP address times out
d. Firewall on XP is disabled via control panel
b. Windows file and printer sharing is enabled
2. Can't see mac from PC
a. Windows file sharing enabled on mac
b. Firewall on mac disabled
c. I used \\MacIPAddr\shortusername
d. ping times out
3. Using dial-up to access internet, how do i tell airport to dial using PC?
a. this feature is working fine from mac
b. If already connected (via instruction from mac), can surf the internet fine from PC
c. Is this even possible from the PC?
4. Can't see printer connected to base station from PC
a. See it fine from mac
b. How do i "find" the printer on the PC?
c. Is Bonjour required for this? (I don't have it on the PC yet)
5. Can't see a "shared" printer on the PC from the mac
a. printer is connected directly to PC
b. Mac's add printer wizardry looks like it may "see" the printer, but then it asks for username and password for PC. This is XP home, with no usernames or passwords. Single user. Nothing seems to work in the credentials pop-up dialog.
Any suggestions on any of these issues is very welcome.
Thanks

Is the PC running any kind of internet security or firewall software?
1. Can't see the PC from the Mac.
2. Can't see mac from PC
Sharing files between an XP PC and a Mac running OS 10.4.x
http://www.ifelix.co.uk/tech/3020.html
3. Using dial-up to access internet, how do i tell
airport to dial using PC?
Jon Sevy has a Java Utility for this purpose.
You will need Java in order to run the utility
http://www.java.com
4 . Can't see printer connected to base station from
PC
Printing from a Windows XP PC to a printer attached to an Airport Extreme Base Station or Airport Express
http://www.ifelix.co.uk/tech/1004.html
Printing from a Windows XP PC to a printer attached to an Airport Extreme Base Station or Airport Express using Bonjour
http://www.ifelix.co.uk/tech/1008.html
Problems with finding Printer Driver on Windows XP when using printer connected to Airport Extreme or Express
http://www.ifelix.co.uk/tech/1012.html
5. Can't see a "shared" printer on the PC from the
mac
Printing to a printer on a XP PC from a Mac running 10.4.x
http://www.ifelix.co.uk/tech/3015.html
Printing to a printer on a Mac running 10.4.x from a Windows PC using Bonjour for Windows
http://www.ifelix.co.uk/tech/3014.html
iFelix

Adding Wireless-N-ONLY Time Capsule to Dual-Band Airport Extreme Network?

I have a dual-band airport extreme which I have configured to create both a wireless-a/b/g/n SSID on my network, as well as a second SSID which is Wireless-N-ONLY (meant to be used with my Time Capsule so that all backups to the Time Capsule via Time Machine are only ever done via Wireless-N).
My Airport Extreme is already configured, and now I just have to configure my Time Capsule on my network...
Can someone briefly run through the "assist me" steps in the Airport Utility that I'd want to follow to configure my Time Capsule so that it's available on my dual-band base station's wireless-N-ONLY network and so that it's not transmitting or receiving any other wireless protocol other than wireless-N?
Thanks!

Hi Bob,
Thanks for your earlier feedback. I now have a dual band TC and the previous dual band EABS and I'm tearing my hair out trying to get these things to play nice! Maybe you can provide some assistance:
1) The TC upstairs is connected to the comcast modem and is the main 'router' in my network. In addition, I'm using the "create wireless network" option on this router to set up both a 2.4 GHz and 5.0 GHz wireless environment.
2) The AEBS downstairs on the opposite end of the house is connected by ethernet - whole house is wired so I'm feeding from the TC upstairs through a switch in the disti box down to an outlet where I have the AEBS. The cat-5 cable is connected to a LAN port on the back of the AEBS.
3) I have the AEBS set up to extend the wireless network. When I do this it only gives me the ability to select one wireless network (I have the TC configured to call the 5 GHz network something different) - In essence doesn't appear to want to let me extend both bands of the wireless network.
The problem seems to be that once I get all the configurations set I have no connectivity and if I try to open the configuration via Airport Utility, its just a spinning gear and will never open to show the settings. This happens to with both the TC and the AEBS. It's like it's in a loop or something.
I immediately disconnect the AEBS from the network and suddenly all is well again.
I know this seems like a rant, but this has been kicking my a** for two days!! I've just about had it with the constant 'hard reset' of the routers and starting over with configuration. If you have any specific things I should do, or settings that are key to set up both devices to extend my wireless network throughout the house I would be so thankful!!
Thanks,
Don

AirPort Extreme Base Station (New one) Dual band problem

Hey, I just got an AirPort Extreme Base Station, simultaneous dual-band today.
Anyone else having some problems with the 5GHz network? Seems my Transmit rate is very unstable. It changes between 7-54. It's 802.11n (5GHz) profile setting.
My 2.4GHz is staying at 54 (Since I set it for b/g).
As well, my MacBook Pro keeps connecting every time i update the airport base station, to the 2.4GHz one.

Welcome to the discussions, dwig365!
With a good connection, the Transmit Rate at 5 GHz should be in the 200-270 range. One of the perplexing issues with 5 GHz is that the much higher frequencies used in this band are absorbed by walls, ceilings and any obstructions much more quickly that 2.4 GHz signals. In other words, there is much less "power" with 5 GHz signals.
I've found that unless I almost have line-of-sight between the router and my laptop a few rooms away, the 2.4 GHz signal is stronger and more stable...hence faster. Taking it another step further, although it is not as "fast" as "n", "g" level signals penetrate and saturate much more effectively. It's a question of trade offs as in return for speed, you must give up penetration power.
It is not likely that you are encountering interference in the 5 GHz band, but it might help to experiment with some different channel settings. Make sure "use wide channels" is enabled under the options button on the Wireless page in AirPort Utility as well.

V. Slow transfer speeds with new dual band Airport Extreme

I have a new Airport Extreme (late 2009, dual band, full 'N' spec) which I am using to replace an older Airport Extreme (early 2008, 5Ghz, 'draft' N).
I have a USB disk attached and was interested in benchmarking the transfer speed of the new Extreme, compared to the previous version. The results are puzzling / alarming.
Shown below are transfer speeds (file copied to the attached USB drive) under different connection standards (2.4Ghz / 5Ghz & a/b/g/n)
'Old' Airport Extreme
5Ghz - 'draft' N : ~5-7 Mb/sec
'New' Airport Extreme
2.4Ghz - b/g : ~3-5 Mb/sec
5.0Ghz - a : ~3-7 Mb/sec
5.0Ghz - N : ~200 Kb/sec
Hence transfer speeds appear to collapse when I try to make use of the 'N' spec with the latest Extreme. I have tried altering items such as - wide channels (on / off), interference robustness (on / off), 5Ghz channel (manual, instead of auto), with no upside.
I seem to be at the point of concluding that either
1. I have a 'broken' Airport Extreme
2. The WiFi card on my early 2008 iMac (which implements I guess the 'draft' N standard) is 'incompatible' with new the Airport Extreme under a 'N' connection.
Any thoughts ?

Since all devices in my wireless network are capable of latest 802.11n protocol, I really do not need older and slower 802.11a/b/g protocols. To achieve above 200 Mbit/sec, 5GHz band with wide channel option turned on is really necessary. Thus I really wish I can turn off the 2.4GHz radio band (seems Apple has set this band as default) of my new dual band Airport Extreme to avoid unwanted bandwidth degradation. Unfortunately this is not possible with radio mode setting in Airport Utility.
The best I can do to force connection with 5GHz radio band (with quite consistent result) is as follows:
On Airport Extreme through [Airport Utility>Wireless] :
Radio Mode: 802.11n only (5Ghz) - 802.11b/g/n
More Options>Wireless Network Option>Transmit Power: 100%
More Options>Wireless Network Option>Use Wide Channels: checked
More Options>Wireless Network Option>5 GHz Network Name:
checked and same network name with extra suffix "(5 GHz)"
On 27" iMac through [System Preferences>Network>AirPort>Advanced>AirPort]:
Preferred Networks:
Create only one profile in Preferred Networks for the above network name with suffix "(5GHz)"
Uncheck the option [Remember networks this computer has joined] to ensure there is only one profile under Preferred Networks .
Once all above settings are done, restart Airport Extreme in Airport Utility. Your computer should connect wirelessly to the base station through 5GHz band after booting most of the time. Even when it is not occasionally, simply go to the Airport icon in main menu bar and click on the network name with suffix "(5GHz)" in dropped-down list to connect manually. With all these settings, I have achieved 300 Mbit/sec bandwidth on my iMac most of the time for fast Time Machine backup.
How I wish feature for better radio mode control by end user will be implemented in next update of Airport Utility. Apple should trust end user's brain better than artificial intelligence (or ignorance ?) in wireless network implementation. Wireless traffic between the two radio bands and among various wireless devices should be segregated specifically in Airport Utility by end users whenever dual band Airport base stations are in use.

Apple TV vs Apple AirPort Extreme Base Station (Simultaneous Dual-Band)

I have an original 40 GB TV that connects to my new ( (latest model)) Apple AirPort Extreme Base Station (Simultaneous Dual-Band) (MC340LL/A). Since upgrading to this new AEBS, my TV will not connect via its internal Airport card. The TV will "see" my "Home-LAN" but always gives the error message, "Connection Failed".
I have tried to Reset and Restore the TV, even the "Restore to Factory Defaults"! I have changed the security settings on my AEBS from an Open Network (no security) to WPA/WPA Personal, WPA Personal. I have changed the "Radio Mode" from "802.11a/n - 802.11b/g" to "802.11a - 802.11b/g". The TV will not connect! I now have it connected to my "Home_LAN" via Ethernet, and it works fine.
Anyone with a similar problem and a suggestion or solution? Do you think the internal Airport Card is the problem? Thanks

As suggested in another discussion area, (AirPort), I reset the AEBS to factory defaults. On the TV, I went to >Settings>General>Network>Configure Wireless>Wireless Networks. I could then see the generic "Apple Network xxxxx" on the TV. From my MacBookPro, I verified that I could connect to the TV by launching iTunes and noting that the TV was now visible in the "Devices" menu. Went back to the AEBS and ran through the "Setup" routine. I did NOT use the "Previous Settings" but instead, saved the old settings profile, created a new wireless network and new settings profile and enabled WPA2 Personal encryption. I then went back to the TV and went through the "Settings" routine again (as noted above). This time, after entering my WPA2 password, the TV connected to the network and problem was solved. Thanks.

Problem consistently printing via new (summer 2011) AIRPORT EXTREME BASE STATION and Brother wireless printer (model HL5370DW). What am I doing wrong?

Thanks in advance for any help you folks can offer. I'm a newb here and will try to offer as much detail as I can about the dilemma at hand.
Scenario: Home network has been recently set up for wireless internet access via NEW Airport Extreme Base Station (purchased September 2011). Units accessing the network include: 2011 Macbook Pro, 2011 Macbook Air, 2007 Macbook, 2009 Macbook Pro, 2 iPhone 3GSs, and a 1st-gen iPad (and a partridge in a pear tree AEBS is configured to run WPA2 encrypted network, as well as a WPA2 guest network. I am attempting to yoke a BROTHER HL5370DW wireless B or G/ ethernet / usb-capable printer to the main network such that any and all units can print wirelessly or its equivalent (i.e., via printer hooked to AEBS through USB hub)
Problem: Despite configuring the Brother printer to recognize the main WPA2 network I created, I am unable to get wireless printing to work. My workaround was to physically connect Brother printer to AEBS via USB, specifically using a Belkin USB hub (after all, I wanted access to usb drives, as well as the printer). This workaround works ONLY SOME OF THE TIME. Generally, after a fresh boot of any computer or after a restart of the AEBS, any given computer will be able to print (i.e., any computer wirelessly connected to the main WPA2 network recognizes the printer). HOWEVER, at random times, printer access is gone (as is access to USB drives connected to AEBS's usb hub). Wireless networks are still up and running when that happens. IS THERE A WAY TO GET THE USB HUB's devices (i.e., printer and usb drives) to ALWAYS REMAIN AVAILABLE AS LONG AS THEY STAY CONNECTED TO THE AEBS? In other words, what accounts for the intermittent loss of the usb peripherals?
Sometimes, I just shut the airport off on whatever computer is having this problem, and the problem goes away. Sometimes, the problem is present across all computers in the house, sometimes only a few are affected. I can ALWAYS see the AEBS in the Airport Utility if the AEBS is connected to the particular computer via ETHERNET CABLE.
My theories:
- true wireless printing (i.e., without usb hub workaround) doesn't work because the N network somehow isn't backwards compatible with the Brother printer, which, i believe, is B/G. Although...isn't Wireless N networking supposed to work with BG devices? I did find a thread (https://discussions.apple.com/thread/2570774?start=0&tstart=0 ) that explains some of the particulars of WPA2 encryption and Wireless B/G issues, but it was beyond my level of comprehension (I'm a psychologist, but not an Apple Genius
- The usb workaround is only intermittently viable because of some flaw in the Airport or Airport Utility that causes dropouts to happen when a Macbook Pro or Air's lid gets closed or one gets opened after having been at a different network (e.g., at my office).
QUESTIONS:
- Should I try to use my old router (7 year old Linksys WRT54G) as an access point and connect the Brother printer to that G-router? How do I do that?
- I wouldn't mind just relying on the usb hub method if I could just insure more consistency (i.e., no random dropouts of peripherals). How could I do this?
Rule out:
- wireless printing works on my printer - it was being recognized back before the AEBS. I had the Linksys router running a WEP network and had the wireless printer talking with no cables to the router and the computers. (I just don't want to revert to using WEP encryption given its lack of security and my trying to protect HiPAA related health information on behalf of patients)
Any help will be greatly appreciated.
Thanks in advance!

13 ASCII characters = 104 (aka 128)-bit WEP
encryption
If turning off WEP works, then you just need to
provide the cameras with the "Equivalent Network Password".
One of the problems with WEP is that the actual
standard relies on a 10 character HEX key for 40bit
WEP and a 26 character HEX key for 128bit WEP.
In order to make things easier, vendors use certain
algorithms to convert simple alphanumeric passwords
(or passphrases) into HEX keys, thus enabling the use
of simple easy to remember WEP password rather than
lengthy HEX keys. The problem is that different
vendors use different algorithms to generate the HEX
key and therefore a ASCII password on an AEBS will be
hashed differently on a non-Apple client and vice
versa.
You may find the following article helpful:
- Apple article, especially the part about
"Third-party client to Airport".
Brilliant idea about trying the system with No encryption on... that DID solve the problem... almost.. once I turned off the encryption option, and restarted the Airport, I got a dialog box showing that the "Base station needs attention" but it didn't indicate WHAT kind of "assistance" it needed. Nonetheless, I closed out of the Airport program only to find that the indicator light, which had been Green, was now, flashing Yellow and I could not connect anything, including my computer. I opened the Airport program again and found the ONLY way I could get the Green light on was to select some sort of encryption option... then the light would go Green again but my cameras would not hook up again, and when I went back in and ONLY changed the option to NO encryption, I got the yellow flashing light and the "this base unit needs attention" warning...
I think your suggestions are almost on the mark... is there any way of reconciling the WEP coding between the cameras and the Airport??? Or turning off the encryption option and STILL have Airport work?
Thanks again for your help and suggestions... I really appreciate it.
geoff

Printing wirelessly to MacBook Pro with Airport Extreme Base Station

I have an Airport Extreme Base Station that I used to use wirelessly until I got Verizon Fios. The Fios technicians said the base station couldn't be used and so it's been sitting unused for a few months. However, I really, really miss printing wirelessly, and was wondering if it was possible to use the Airport Extreme Base Station ONLY to print wirelessly, and not connect it any way to my internet (I don't want to mess with any of the fios stuff at all).
If it's not possible, is there any other way to print wirelessly without purchasing another product or special printer. I have a HP c4480 printer.
Thanks!

If your printer has a USB cable the easy way to go about this in my opinion is to plug that USB cable into your Extreme base station. I have the Extreme ABS that looks like a flying saucer. I plug the usb cable into the port that has the symbol that doe NOT look like this <--> rather it looks like a Saguaro cactus.
My computer then sends print documents to the Extreme via WiFi and then Extreme sends them to the printer via the USB cable.
If your Airport status is not showing in the Mac's menubar go to system Prefs/Network/Airport and check a little box so it will show up in the menu bar.
Now if your Extreme is plugged in the wall and powered up your Mac should be able to find it. Click on that menubar item for Airport and scroll down and select your Airport Extreme. I don't know for sure what its name will be. It should still be the same as it used to be when you used it last.
Now try printing a simple document. In the print dialog window you should be able to select what printer you want to use. If your new Extreme printer is listed select it. You may need to click on Print & Fax and figure out how to select it from there, and choose it to be the new default printer.
I think this info will do the job. Whenever you want to print you have to go to the Airport icon in the menubar and change your airport connection from your Verizon stuff to your Extreme. Then of course you have to change back when you are done. That is why it would be great to toss the Verizon WiFi radio out the window and just plug your Verizon modem into your Extreme WiFi radio transceiver (router). But I understand you cannot deal with that at this time.
If this does not do the job, if I have missed something, I will bet you 5 bucks that you can still figure it out if you just look at any error messages and/or look at the Print&Fax prefs and the Print dialog windows etc. and see what I may have missed. Maybe you have to go to SystemPrefs/Sharing and allow your printer to be shared. I don't think so. The way I figure any of this stuff out is to just look at stuff and think and try things and see what happens.
Your Verizon setup should be something like this.... a cable comes into your house and goes to a 'modem'. From there and ethernet cable (CAT-5 cable) goes from that modem to your Verizon router (WiFi radio transceiver).
As for getting rid of the Verizon router, when you are ready to give it a go, simply unplug the ethernet cable (it has a plug on the end that looks like the kind of plug that telephones use to plug into the wall, except it is a bit wider, but still has that same kind of snap-lock tab) that comes from the Verizon modem (the modem has the heavy round cable and probably many blinking lights) and plug it into the Extreme. Mine has an icon on the Extreme that is many dots in a circular pattern.
At this point you may have to unplug the Verizon modem form the wall AC power and the Extreme also. Then plug them back in, wait a minute, go to your Airport icon on your Mac menubar, Select Extreme and start surfing the web.
It really is that simple with a Mac. Maybe Verizon has found a way to make things difficult but my guess is no. Any password should be taken care of in your Airport Setup Utility program. It should be the same password(s) as you used before when you used your Extreme.

Wireless HP Printer on Dual Band Airport Extreme Base Station

Similar Messages

Maybe you are looking for