Wireless hp6700 printer

can printer and laptop be connected by wireless without going thru internet connection router?

Not this one, sorry.  Older models can do this, but not the newer ones.   You can just get a cheap wireless router and use it for connecting between the compter and printer, the router does not have to connect to the Internet.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Similar Messages

  • Can I FAX from a Wireless hp6700 printer

    Can I FAX  from a Wireless  hp6700 printer?   Do I need to connect it to a phone line or does it have fax software that will allow me to fax to a fax number via my home wireless network->Internet->Fax number.
    Sudhir

    Hi,
    You need a phone cord as mentioned in its manual:
    Test fax setup
    You can test your fax setup to check the status of the printer and to make sure it is set up correctly for faxing. Perform this test after you have completed setting up the printer for faxing. The test does the following:
    • Tests the fax hardware
    • Verifies the correct type of phone cord is connected to the printer
    • Checks that the phone cord is plugged into the correct port
    • Checks for a dial tone
    • Checks for an active phone line
    • Tests the status of your phone line connection
    The printer prints a report with the results of the test. If the test fails, review the report for information on how to fix the problem and rerun the test.
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • Hp6700 Printer: can't connect to D-Link DI-514 Wireless Router when Broadcast SSID is set to NO.

    HP6700 Printer:  can't connect to D-Link DI-514 Wireless Router when Router Broadcast SSID is set to NO. My MAC LapTop and HP LapTop both work with the SSID set to NO. If I change the Wireless Router to Broadcast SSID is YES, then the HP6700 Printer can connect to the Wireless Router. I setup the Printer telling it what the SSID and Password were, the same as both of my LapTops, but it never connects, unless I change the Router to broadcast the SSID. Help!
    This question was solved.
    View Solution.

    Did you try updating the firmware on the DI-514?
    You can also try setting a static IP on the printer, then assign the printer to the static DHCP list in the router interface.
    To give your printer a static IP address:
    - Print a Network Config Page from the front of the printer. Note the printer's IP address.
    - Type that IP address into a browser to reveal the printer's internal settings.
    - Choose the Networking tab, then Wireless along the left side, then the IPv4 tab.
    - On this screen you want to set a Manual IP. You need to set an IP address outside the range that the router automatically sets (called the DHCP range). If you do not know the range, change the last set of numbers (those after the last '.') to 250
    - Use 255.255.255.0 for the subnet (unless you know it is different, if so, use that)
    - Enter your router's IP (on the Network Config Page) for the gateway.
    - Enter 8.8.8.8 for the first DNS and 8.8.4.4 for the second DNS. This is Google DNS. You can choose another external DNS if you wish.
    - Click 'Apply'.
    Now, shut down the router and printer, start the router, wait, then start the printer.
    After this you will have delete and re-add the printer on your Mac.
    Show support by clicking the blue Kudos star in the post that resolved your problem. Doing so will help other forum members find their solutions too.

  • How can i use my old airport express with my new imac and wireless hp print

    i just bought my first imac (intel) and a wireless hp printer. i now realize that a wireless connection between my imac and my printer needs a router.
    i have an airport express base station, which is a few years old. I can't find my documentation, so i don't know its specifications.
    how can i find out the specs of the airport express i have and whether i can use it now? it says that it is model a1084 100-240v~ 0.2a 50-60 hz.
    does that tell any knowledgeable people out there about the specs? can i search the apple website by serial number and find the specs?
    thank all of you potential responders ahead of time.

    Hi green jean
    Try this > http://www.apple.com/airportextreme/features/printing.html
    but also see > http://docs.info.apple.com/article.html?artnum=305293
    Dennis

  • Can I print from an iPad to an HP 6500 wireless E709n printer

    I have an HP6500 wireless E709n printer and I want to print from a Apple iPad Model MC705LL, version 6.0.1, 3rd Generation, I get a message when I try to print that - No AirPrint Printers Found. How can I get the printer to accept the print command from the iPad?
    This question was solved.
    View Solution.

    @pgarden717
    Are you getting any type of error message when you try to print using app?  I am linking you to a troubleshooting document for the app.
    Hp ePrint app
    Let me know how it goes.

  • HP Wireless Direct Print

    im using my new hp laserjet pro 300 with Wireless Direct Print. i can use the wireless direct print feature great with my iphoe as well as my android phone. advertisements suggested that i would also be able to print from my wireless laptop using the HP Wireless Direct Print feature. was i mistaken?

    Install the HP eprint Mobile Driver
    Download the driver from www.hp.com/go/eprintmobiledriver.
    Launch the installer and follow the instructions in the install wizard.
    Register the HP ePrint Mobile Print Driver
    Registering the driver to the Windows or Mac computer is required for the HP ePrint Mobile Driver to send print jobs from your print client, into your ePrintCenter.com account, to an HP ePrint enabled product registered to ePrintCenter.com. For direct IP printing from a Windows client over the local area network to a supported PostScript device, ePrintCenter.com registration is not required and is therefore optional if web-based printing is not required.
    ePrint Credential Setup
    This default option presented during installation guides you through enabling the HP ePrint Mobile Driver for web-based printing. When presented with the HP ePrint Registration option within the HP ePrint Mobile Driver, you are asked to enter an email address and Personal Identification Number (PIN). If you skip this step during driver installation, you can access the registration option again from the user interface of the installed driver.
    Email
    The HP ePrint Mobile Driver registration process asks you for an email address. This email
    address is used by ePrintCenter.com to send a system-generated Personal Identification Number required to register the HP ePrint Mobile Driver to your Mac or Window client. The email address you provide can be the same email address used to create your ePrintCenter account, or any other email
    address that you have access to read received emails.
    PIN
    The registration process sends a Personal Identification Number (PIN) from [email protected] to the email address entered into the HP ePrint Mobile Driver registration screens. Supply the provided PIN to the HP ePrint Mobile Driver. Registration status is provided through the user interface (Success or Fail). Click OK from the Registration Successful acknowledgement screen. The credentials provided during registration are saved for this computer, which enable the print client to send print jobs from any installed application on the Mac or Windows system.
    The system can now print to registered HP ePrint-enabled products.
    Let me know if you need anything else. Thanks!
    If I have SOLVED your issue, please feel free to provide KUDOS and make sure you mark this thread as SOLUTION PROVIDED!
    Although I work for HP, my posts and replies are my own opinion and not those of HP.

  • HP Wireless G Print Server not detected during installation

    I have HP2101 wireless g print server to connect to my HP officejet 6210 and I have an HP computer using windows 7. when i put the dvd into computer, follow install instructions, it tells me to connect print server to the computer and wait for the pc to find it, nothing happens, it is not detected. the power cord is in, the mini usb is connected to pc and print server and thre is a green steady light on the power icon, but it does not detect. Help!

    To the TOP!

  • How do I make my HP P2055dn printer into a wireless network printer for 5 computers

    How do I make my HP P2055dn printer into a wireless network printer for 5 computers? Windows versions on computers used are  XP,Vista & 7.
    Thanks
    Leon

    Unplug the USB cable from the printer.  Plug your printer into your wireless router with an Ethernet cable.
    Next, on each computer, get the latest software for your printer from the "Support & Drivers" link at the top of this page.  Install it and select "Network" installation when it asks.
    Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
    I am employed by HP

  • Samsung Galaxy Note 10.1 2014 Edition; Wireless Direct Printing Issues

    Good day everyone. The subject refers. I have been trying to connect my tablet to my hp printer (LaserJet Pro 200 color MFP M276nw) using wireless direct printing without success. What normally happens is when I try to detect the printer through wifi on the tablet, the error message I get from the tablet is "Network disabled because internet connection is slow". What can I do???

    Hello OgoOluwa,
    Welcome to the HP Support Forums!
    Regarding the troubles getting the Wireless Direct connection working with a Samsung Galaxy Note, does this error display only on the Wireless Direct network?
    I have not been able to reproduce the error, but I have found something that addresses the error on another support site that might be worth a try.
    Getting "Network disabled because internet connection is slow" during setup<--- Not a HP support site, nor is it related to a printer, but the error is the same and follows suite with a connection issue with a Samsung product.
    Let me know if this suggestion is helpful.
    JERENDS
    I work on behalf of HP
    Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

  • HP Officejet Pro 8000 Wireless: HP printer unable to connect to wireless router.

    Installing new printer,  getting error msg saying HP printer unable to connect to wireless router.   MAC address filtering may be enabled on your wireless router which can prevent HP printer from connecting to your wireless network during setup.
    SOLUTION says:  If MAC address filtering is enabled and you would like to keep it enabled, you must add the MAC addressof your printer to the list of permitted devices for your wireless router before continuing.
    My router is WD My Net N900 Router. MAC filtering is diabled. My security mode is WPA/WPA2 Personal. 
    I have run out of ideas to try and fix the issues, would appreciate some help.
    Thanks,

    Hi Jamshidk
    I am surprised you are getting that message and you checked the router settings and it is showing that the Mac Filtering is disabled.
    I would suggest connecting the printer to the router with a ethernet cable to get a valid IP address and then setup the wireless.
    Print a configuration report.
    http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&​dlc=en&docname=c01554589&lc=en&product=3760410&tmp​...
    Type the IP address from the configuration page  in the address bar into internet explorer browser. This will open the embedded web server for the printer. Click on the Networking tab, on the left hand side select wireless. After this is setup and applied, disconnect the ethernet cable.
    Should be on the wireless network. Takes about 1 minute.
    Run the add printer wizard.
    Go to start, devices and printers and select add a printer. (Win 7)
    Test the printer.
    If you need more assistance just let me know.
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
    Gemini02
    I work on behalf of HP

  • How do I print from an iPad 3 Generation to an Officejet 6500 wireless E709n printer

    I am a new iPad user and I have a 3rd Generation iPad and want to print to an Officejet 6500 wireless E709n printer but the iPad does not recognize the printer when I try to print or visa-versa.  I am using a Ubee Modem/Router and don't know what to do. What do I have to do or what do I have to download to make the iPad and HP Printer print.

    tpgarden wrote:
    .... No AirPrint Printers Found. And it won't Print
    Hi,
    Your printer is not in the list therefore no AirPrint available. Your printer does not support ePrint therefore you can use Home & Biz apps. Have you downloaded apps to your iPad yet ? If yes, please try:
    Pressing the iPad home button two times (a list of currently running apps should appear at the bottom of the screen).
    Press and hold the HP ePrint Home & Biz app until it starts to move around.
    Press the red 'X' on the app to end its process.
    Press the iPad home button.
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • MacBook Air will not print on wireless Epson printer.  It says 'filter failed'

    MacBook Air all of a sudden will not print on wireless Epson printer.  The error message is 'filter failed'.  Shut down everything and rebooted, but still not printing.

    Launch the Console application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad and start typing the name.
    Select
              /var/log ▹ cups ▹ error_log
    from the hierarchical list on the left side of the Console window. If you don't see that list, select
              View ▹ Show Log List
    from the menu bar.
    Each message in the log begins with the date and time when it was entered. Select the messages from the time of the last failed printing attempt. Copy them to the Clipboard by pressing the key combination command-C. Paste into a reply to this message (command-V).
    If there are runs of repeated messages, post only one example of each. Don’t post many repetitions of the same message.
    ☞ The log contains a vast amount of information, almost all of it useless for solving any particular problem. When posting a log extract, be selective. A few dozen lines are almost always more than enough.
    Please don't indiscriminately dump thousands of lines from the log into this discussion.
    Please don't post screenshots of log messages—post the text.

  • My wireless hp printer will not communicate with my hp pc

    my wireless hp printer will not communicate with my pc

    Please read this post then provide some details. What printer model? What operating system? How is the printer connected - Wireless LAN or bluetooth?
    Running the diagnostics at http://www/hp.com/go/tools may help resolve the issue.
    Bob Headrick,  HP Expert
    I am not an employee of HP, I am a volunteer posting here on my own time.
    If your problem is solved please click the "Accept as Solution" button ------------V
    If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

  • I have a MacBook Pro and can't print pdf files or word documents using my HP Wireless Photosmart Printer.  It will print files from the internet.  Any suggestions or ideas will be greatly appreciated.  Thank you.

    I have a MacBook Pro and can't print pdf files or word documents using my HP Wireless Photosmart Printer.  It will print files from the internet.  Any suggestions or ideas will be greatly appreciated.  Thank you.

    Hello, SoonerAnesthetist. 
    Thank you for visiting Apple Support Communities.
    Here is an article that I would recommend going through when experiencing this issue.
    OS X Mavericks: Solve printing problems
    http://support.apple.com/kb/PH14142
    Cheers,
    Jason H.

  • Wireless Network Printing Solution

    Yesterday I discoverd a solution that allows you to set up a HP Photosmart C7200 Series (Model Number: SDGOB-0713) on a wireless network... This is related to an issue we had printing from an iMac, MacBook Pro and a Mac mini to two different identical HP C7200 printers.
    We found that if you plugged both the printer and the Mac's directly into the network (no wireless involved) you can successfully auto detect the printer with a Bonjour option and an HP IP option, Note: prevously we couldn't detect it at all. Then we installed both print queue options and found that the Bonjour option stop's working once you switch back to wireless but the HP IP Queue contenues to work great wired or wireless.
    Wireless Access Points used (Buffalo WZR-AG300NH)

    Sorry This Printer does not have e-print and  wireless capability .To send print job through your ipad requires e-print capability and not necessarily wireless enabled printer  .
    Click the Kudos star if this was helpful. Thank You!
    (Although I am an HP employee, I am speaking for myself and not for HP)

Maybe you are looking for

  • Computer can no longer find my printers unless I go to wireless

    I have an older 24" imac running 10.6.8 and am suddenly unable to print on any of my printers unless I go through wireless.If I go to print utility I get a communications error message but it's not the cable or printer. The computer says "printing" a

  • Multiple free goods for one main material

    Hello SAP Gurus, we have a business requirement that to issue multiple free products for one main product, if the upliftment is beyond the specified quantity. Using free goods functionality, is it possible to achive the above requirement. e.g        

  • JSP classes warning:

    I have a webroot/WEB-INF/jsp directory with my jsps. When I compile I get the following warning for all my jsps: Warning: package name web2d_inf._jsps does not match source file name C:\CVSHome\Orion\jdev\registration\regView\classes\.jsps\_WEB_2d_IN

  • Create material master using BAPI .(Mat. internal number range)

    I would like to create the material using BAPI. (Material is internal number range). I am trying to create the material using BAPI  BAPI_MATERIAL_SAVEDATA, but material number is required field as per BAPI documentation . Can you please suggest me th

  • Can't find the question I've asked... no wonder there's no response!!!

    <blockquote>Locking duplicate thread.<br> Please continue here: [/questions/757172]</blockquote><br> that was my question - yahoo and facebook loading the first time, but not fully functional, then sometimes doesn't loading at all