Wireless Keyboard and Mouse connection lost when computer wakes up

Every time my computer wakes up I get the message "Connection Lost" referring to the mouse (Mighty Mouse) and keyboard. I have to wait a couple of seconds for them to start working. I tried to remove them from the list of Bluetooth devices and then pair them again, but had no success. It's pretty annoying to have this happening everytime the computer wakes up.
Is anybody else experiencing this? Any suggestions?
Thanks.
richard

I have this issue as well, and havn't found a sufficient answer on the forums as of yet.
I can pair my mouse every day, and it will work fine, until I leave it at night when my computer shuts down. When I return in the morning I have no mouse, and have to go back to the bluetooth setup wizard and re-pair the mouse by turning it off then on again. I can't even just come in and turn the mouse off and on and have it work. I have to actually go through the setup wizard.
I CAN however, go to the bluetooth preferences, click on the mouse, and choose "connect" when it is turned off, then turn it on and it will connect without having to re-pair, but this is just as tedious and annoying as the whole setup process.
It's so annoying to have to have a wired mouse plugged in just so I can pair my wireless mouse every morning. Kind of defeats the purpose of a wireless mouse.
When I orginally bought the mouse and keyboard I had to return the original mouse because it wouldn't hold a connection even when I was using it. Obviously these wireless mice of Apple's need some more TLC in the engineering dept.

Similar Messages

Intermittent lost of connection of wireless keyboard and mouse, intermittent lost of connection of wireless keyboard and mouse

i'm using the wireless keyboard and mouse. ocassionally i encounter intermittent lost of connections. changed (to new) batteries but problem continues.
anyone knows why and what can be done?
tks
Nasayah

Troubleshooting wireless mouse and keyboard issues
http://support.apple.com/kb/TS3048

TS2662 Wireless keyboard and mouse were working fine until today; installed new batteries in both when they wouldn't work-says they are connected intermittently, but can't use either one-have tried to re-pair and nothing happens-codes not recognized-

i have been using my wireless keyboard and mouse with no probs until today-installed updates this morning-since I restarted have been unable to use either device-have tried everything Apple suggests to do- re-pairing unsuccessfully; turned everything off and back on-sometimes the Bluetooth says it is connected, othertimes not-but even when it says it is connected the keyboard/mouse don't work; put in new batteries-no go also; bluetooth icon is on. Anyone have any ideas????

Troubleshooting wireless mouse and keyboard issues
http://support.apple.com/kb/TS3048

Ultraslim Plus Wireless Keyboard and Mouse not connecting

I just bought the Ultraslim Plus Wireless Keyboard and Mouse, but I can't get either to work. My machine (ThinkPad X230-2324-HQ4) does not have a CD drive for me to use the install CD, so I found and downloaded the driver from your support site:
http://support.lenovo.com/en_US/product-and-parts/detail.page?&LegacyDocID=MIGR-77112
I installed the driver properly and restarted my computer, but neither the keyboard or mouse will connect still. I've checked the batteries, and I've verified that my ThankPad's Bluetooth drivers are up to date and working properly, but I still can't seem to get it to work. I've found posts on here from people with similar issues, but they seem to all be related to the Ultraslim, not the Ultraslim Plus. The Ultraslim Plus does not include a USB dongle for connection.
Please help!

The Ultraslim Plus Wireless Kit is Wireless 2.4G solution, it is not Bluetooth solution. It has a dongle when shipping. Maybe you can check the mouse or Keyboard inside and find the dongle. You can open the mouse battery bin, it should be a dongle at top of two batteries. If you still can not find the dongle, I suggest you call the Lenovo help center since you don't have the dongle.

My wireless keyboard and mouse do not work on my All-In-One computer?

Q.: My wireless keyboard and mouse do not work on my All-In-One computer?
A.: If your wireless keyboard and mouse do not work even after changing the batteries, please try re-syncing them by following these steps.
1. Make sure the computer is on, plug in the USB receiver. Push the button on the USB receiver until it flashes blue.
2. While the receiver is still flashing, press the red connect button on the keyboard (Make sure the batteries are installed). The USB receiver should stop flashing after pressing the button on the keyboard. It may take up to 8 seconds to sync.
3. Repeat the same process for the mouse. Push the button on the USB receiver, then press the connect button on the mouse (Make sure the mouse is on).
Note: This applies to all MSI All-In-One computers that include the ES500W wireless keyboard and SW130 mouse.

"This machine has an added 4 USB ports, could this be causing a problem?
It definitely could be the source of the problem. Perhaps the PCI card was bumped loose during shipping?
Have you tried removing the card? That's where I would start.
Keep us posted.

TS3048 My early 2009 Mac Pro does not connect via bluetooth to my sound bar or bluetooth mini speakers. Both my wireless keyboard and mouse have no problems connecting. What do I need to do to connect to external bluetooth devices?

My early 2009 Mac Pro does not connect via bluetooth to my sound bar or bluetooth mini speakers. Both my wireless keyboard and mouse have no problems connecting. What do I need to do to connect to external bluetooth devices?

I would always have a wired keyboard and mouse on hand (need not be expensive ... any cheap wired devices will work). "Emergency recovery" procedures can activate features in random order, so the opportunity to select a recovery partition may pass before the wireless devices are recognized.
That will let you select the "turn on Bluetooth" icon.

Hi, I bouhgt a used Apple Power Mac G5, I want to buy a blue tooth card for the same to use wireless keyboard and mouse, i am just curious that why do i need to provide the serial number of my computer, is there any compatibilty issue?

Hi, I am new in Apple Computer, I bought a used Power Mac G5. I want to buy a blue tooth card for the same to use wireless keyboard and mouse. so why it is mandatory to provide the serial number of the machine?

Hello, Serial# not needed...
At the Apple Icon at top left>About this Mac.
Then click on More Info>Hardware and report this upto *but not including the Serial#*...
Hardware Overview:
Machine Name: Power Mac G5 Quad
Machine Model: PowerMac11,2
CPU Type: PowerPC G5 (1.1)
Number Of CPUs: 4
CPU Speed: 2.5 GHz
L2 Cache (per CPU): 1 MB
Memory: 10 GB
Bus Speed: 1.25 GHz
Boot ROM Version: 5.2.7f1

My Mac wireless keyboard and mouse won't reconnect

My Mac wireless keyboard and and mouse one day disconnected and I can't reconnect. They have new batteries.

Hi Saint Anne,
Happy Thanksgiving Day! Since both of your wireless input devices are not working at the moment, do you have a wired mouse you can use to straighten this out? Here are some troubleshooting steps to try:
Wireless Connection issue
Make sure Bluetooth is turned on
First, choose Apple () menu > System Preferences > Bluetooth and confirm that Bluetooth is turned ON.
The Bluetooth menu bar icon should turn:
Black if Bluetooth is turned ON and no devices are connected.
Light grey with three dots if Bluetooth is ON and at least one wireless device is connected.
Light grey (or disappear completely) if Bluetooth is turned OFF, or if the iMac is unable to communicate with the Bluetooth module.
Refer to the Bluetooth Menu Icon table below for more information on determining the Bluetooth status. If the Bluetooth icon does not appear, or if the menu bar status continues to indicate that Bluetooth is off, restart your computer and then attempt to turn Bluetooth ON again.
Bluetooth OFF
Bluetooth ON and connected to wireless device
Bluetooth menu icon
Bluetooth status
Bluetooth turned on, but there are no devices connected to the Mac. See the "Make sure the wireless mouse or keyboard is turned on" section of this article.
Bluetooth turned on and at least one wireless device is connected. See the "Make sure the wireless mouse or keyboard is turned on" section of this article.
When this icon flashes, at least one wireless device has a low battery. Click the Bluetooth icon to identify the affected device, then replace the batteries.
Bluetooth is off. Click the Bluetooth icon using a USB mouse and select "Turn Bluetooth On". Note: Mac OS X won’t allow Bluetooth to be turned off unless a USB mouse is connected.
Bluetooth offline. Restart your Mac. If the Bluetooth status doesn’t change, disconnect all USB devices and restart your Mac again.
Make sure the wireless mouse and keyboard are turned on.
Mouse
Slide the On/Off switch on the bottom of your mouse to turn it on. Note: If the battery compartment cover is not installed properly the On/Off switch may not function correctly or may be difficult to operate. Remove the battery compartment cover and carefully reinstall it.
When your mouse is on and paired, and the batteries are charged, the indicator light glows steadily.
If your mouse isn’t paired with a Mac, the indicator light will blink, indicating your mouse is in discovery mode and ready to pair.
If the indicator light doesn't illuminate, check to make sure you have two good batteries and that they're installed correctly.
Keyboard
Push and release the On/Off switch to turn on the Apple Wireless Keyboard.
When your keyboard is on and paired, and the batteries are charged, the light will glow steadily for several seconds, then turn off.
If your wireless keyboard isn’t paired with your Mac, the indicator light will begin to blink. This indicates your keyboard is in discovery mode and ready to pair with your Mac.
If the LED doesn't light up, remove the batteries to make sure they're good and that they're installed correctly.
Check preferences
From the Apple () menu, choose System Preferences, then choose Bluetooth from the View menu. The Bluetooth preferences pane will list the Bluetooth devices paired with the computer, the status of the devices (paired or connected), and whether Bluetooth power is on or not.
Click the gear icon and choose "Connect" to connect a device that is powered on.
To set up a new device, click the + icon and follow the Bluetooth setup assistant.
If the Mouse System Preferences pane is open and no wired or wireless mouse is connected, your Mac will immediately start looking for a wireless mouse (with Mac OS X v10.6. For Mac OS X v10.5, the Setup Assistant should open).
Keyboard or mouse intermittently stops responding
Click the mouse
Click the mouse once to reconnect it with your Mac. It may take a moment for the mouse to respond.
Check the battery level of the mouse. Choose System Preferences from the Apple (), then choose Mouse from the View menu. The battery level indicator is in the lower-left corner. Replace the batteries if they are low. Note: Choose Keyboard & Mouse from the View menu with Mac OS X v10.5. For more information on keyboard and mouse battery levels in Mac OS X v10.5, see Desktop computers: Troubleshooting wireless keyboard and mouse issues.
Press a key on the keyboard
Press a key on the keyboard to reconnect it with your Mac. It may take a moment for the keyboard to respond.
Check the battery level of the keyboard. Choose System Preferences from the Apple (), then choose Keyboard from the View menu and select the Keyboard tab. The battery level indicator is in the lower-left corner. Replace the batteries if they are low.
Check for signal interference
Wireless networks that operate on 2.4GHz may cause interference.
Move cordless phone base stations, microwave ovens, and other 2.4GHz electrical devices away from the Mac if you suspect interference.
Keep wireless devices within 10 meters (33 feet) of the Mac.
Avoid putting metal objects between the device and the Mac.
Mouse doesn't scroll up or down or side to side
For mice that have a scroll ball, refer to How to clean your Mighty Mouse.
Check the Scrolling speed slide-control at the top, and make sure the “Scroll” checkbox is checked.
For scrolling side-to-side, make sure the application you’re using supports side-to-side scrolling.
Remember, scrolling is done with one finger, and navigating is done by swiping side-to-side with two fingers.
Navigating moves from page to page in a document or internet browser unlike scrolling.
Mouse does not track as expected (jittery, jumpy, slow, fast).
The Apple Wireless Mouse can be used on most smooth surfaces, however if tracking issues occur try these options:
Choose System Preferences from the Apple () menu, then choose Mouse from the View menu. Set the Tracking slider to adjust how fast the pointer moves as you move the mouse.
Try using a different surface to see if the tracking improves.
Turn the mouse over and inspect the sensor window. Use compressed air to gently clean the sensor window if dust or debris is present.
If multiple Bluetooth wireless devices are in use nearby, try turning them off one at a time to see if the issue improves. Bandwidth intensive devices could affect tracking.
Mouse buttons do not work as expected.
The Mouse preference pane allows users to customize the mouse features to meet their needs.
Choose System Preferences from the Apple () menu, then choose Mouse from the View menu. Set the Tracking slider to adjust how fast the pointer moves as you move the mouse.
Try using a different surface to see if the tracking improves.
Turn the mouse over and inspect the sensor window. Use compressed air to gently clean the sensor window if dust or debris is present.
If multiple Bluetooth wireless devices are in use nearby, try turning them off one at a time to see if the issue improves. Bandwidth intensive devices could affect tracking.
Keyboard has one or more keys that do not respond.
Use the Keyboard Viewer to test whether the keyboard keys are responding correctly when they are pressed.
Choose System Preferences from the Apple () menu, then choose Language & Textfrom the View menu (or International from the View menu in Mac OS X v10.5 or earlier).
Select Input Sources.
Select the Keyboard & Character Viewer checkbox.
Enable the input source for the keyboard layout you are testing by selecting the checkbox next to it.
Make sure that "Show Input menu in menu bar" is enabled.
Choose Show Keyboard Viewer from the Input menu in the menu bar, as shown.
The Keyboard Viewer shows the keyboard layout.
Type the key on the keyboard that doesn’t respond and observe whether the corresponding key highlights on the Keyboard Viewer. If it does, that particular key is functioning correctly. In the sample shown above the shift and command keys are being pressed.
If the mouse keys feature in the Universal Access System Preferences pane is enabled, many of the keyboard keys may not respond as expected.
Try starting up into single user mode to determine whether a software issue is causing the issue.
Cheers,
Judy

Ultraslim wireless keyboard and mouse not working

Hi , I purchased the Lenovo Ultraslim Wireless Keyboard & Mouse (pn: 57Y4700) about 4 months ago for use with my T60 laptop (which i use with a docking station and large lenovo monitor at work).
Everything was woking fine until last Monday when I can into work after the weekend and neither the mouse or keyboard worked. I replaced the batteries in both, rebooted the machine several time, switch the USB ports for the nano receiver, but nothing seems to have worked.
I looked online for troubleshooting options, but did not find anything.
The mouse and keyboard don't seem to have a "sych" button - if I recall correctly everything worked right out of the box.
My theory is that the nano reciever was damaged (not sure how) -- but don't know how to proceed:
can the nano reciever be replaced;
any other options to troubleshoot;
any chance that this could be a software problem
Thanks

Hi coffee12345,
Welcome to the HP Forums!
I have read your post on your wireless keyboard and mouse not working with your desktop, and I would be happy to help you! To begin, I need to ask you a few introductory questions:
What is the Product and Model Number of your desktop?
What version of Windows are you using?
Is this a recent issue, or has it been like this since day one?
Are you using a USB hub to connect your peripherals or is it directly plugged into the computer?
Please re-post with the necessary information, and I look forward to your reply!
Regards
MechPilot
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

Wireless keyboard and mouse with emac

Hi,
Does anyone know whether the new wireless keyboard and mouse will work with eMac without built in bluetooth, and USB 1.0?
Should I use a USB 2.0 dongle or a USB 1.0 dongle.
Any help would be very appreciated.
thanks

That is how I use my macbook. When I start up in the moring, I turn the mouse, keyboard and monitor on first, I then hit the power button on the macbook and immediately close the lid. The macbook will then boot up on the external display. Just in case you allow the macbook to go to sleep, you need to go to allow bluetooth devices to wake the computer. You set this in the bluetooth system prefs.
Glor

I have just replaced my mac mini because previous motherboard was damaged. I want to pair with my existing wireless keyboard and mouse but can only pair with thebold mac mini which will not start. Any ideas?

See title. How do I unpair a wireless keyboard and mouse when the previous paired mac mini is damaged and will not start?

You should be able to go to System Preferences -> Keyboard and System Preferences -> Mouse and discover the bluetooth devices.
Also, do you have a bluetooth icon on the top bar of your mac? Should look sort of like this:
If you can figure out which device is which (by trial and error, if nothing else), you can connect to them on this menu.

Can't use Filevault 2 with Wireless Keyboard and Mouse

Am I the only one who can't get File Vault 2 to work with a wireless keyboard and mouse? It seems that the "Recovery Partition" of Lion which you have to log into in order to enable File Vault 2 doesn't support BlueTooth devices so it's impossible to log in and start the encryption process. And after using a USB keyboard to do the encryption, I now can't log onto the encrypted disk for the same reason.
I can't believe that nobody else has noticed this, so what am I doing wrong?
Thanks

I have exactly the same problem; I have an original Apple Wireless keyboard (the older, full-size white and clear plastic keyboard), and a Logitech MX-Revolution mouse, both work just fine using the recovery partition, but don't respond at all for the FileVault login prompt.
The mouse just doesn't do anything, and if others are getting USB devices to work then my mouse should work since it has its own wireless receiver, masquerading as a USB device, but it's just frozen in place. Meanwhile my keyboard appears to connect normally, but the login screen is completely unresponsive, pressing caps-lock doesn't cause the caps-lock button to light up, even though I know the keyboard works just fine.
Considering the push for more wireless by default it seems odd that this problem exists, especially when my devices all work perfectly fine for selecting start-up disk, starting up from CD and so-on. Does anyone have a more concrete fix for this? FileVault 2 was one of the features I was really looking forward to but I can't even properly enable it, I'm just fortunate that Lion at least stops the process if you don't log-in successfully the first time.
As a side note; is the same pre-boot login required if you enable FileVault encryption on a non start-up volume? If not, at what point does the volume become available? I'm hoping to separate my OS and user folders onto my SSD and regular HDs respectively, but if I enable FileVault for my HDs only, will I still need the pre-boot login?

Initial set up with wireless keyboard and mouse!!

My gods, I set up a mac mini with wireless keyboard and mouse. It stead fastly refused to find the brand new apple wireless mouse. I had to plug a wacom in, in the end to get anywhere. Then it would not find the keyboard, again apple wireless. It did find the keyboard but when it started the pairing just came up with no keyboards were found.
I struggled in the end and after around 10 minutes blagged the keyboard, I don't know how it just suddenly worked.
Thinking about this I had the self same problem on a wireless keyboard and mouse for an iMac as well I installed for a friend, it took ages and ages for the computer to discover the two apple devices.
Am I just unlucky or is there voodoo involved? Luckily I am a seasoned apple user so got there in the end, but if I were a switcher and the very first experience of my new mac was it could not find its own mouse, I would not be impressed.

I've been using the Apple wireless mouse and keyboard with my Mac mini for about a year.
I've noticed that whenever the batteries for the two devices are running very low, they may not be recognize by the mini. Other than that, they are fine.

Can the iPad work with a wireless keyboard and mouse?

Would like to know if the new iPad will work with a wireless keyboard and mouse!

There are quite a few threads requesting this facility, so I thought I would choose this recently active (at the time of writing) post to reply to, in the hope some thinking appleite with influence stumbles upon it.
I totally get Apples philosophy of not polluting their interface design concepts with the introduction of a clunky so-last-year cursor; I actually agree. What I can't understand so much is that there are a number of apps that could benefit from mouse support. The one I need is RDP. This class of apps allow us to connect to servers running other operating systems using the IPad; why not authorise CERTAIN APPS to access the Bluetooth mouse stack, and let us have joy. It doesn't affect the iPad experience in the slightest, at least not to it's detriment.
The new retina screen is such that I actually prefer the experience of using my iPad to connect to the server than my laptop!, but given I develop software, there is no way my stubby finger can compete the clinical accuracy of a mouse when using intricate interfaces such as MSDE. With just that one addition, I would practically move into the post pc era you tout so much, at least in my interfacing With the post pc pc,s :).
Thanks
Paul

Apple Wireless Keyboard and Mouse + Bootcamp = screensaver problems

I can't seem to get the screensaver to activate when using the apple wireless keyboard and mouse under windows XP with Bootcamp.
I know its a problem with the wireless devices because if i restart the computer and not press anything (ie. mouse or keyboard) then the screensaver will work.
However as soon as I press the mouse or move the cursor around, the screensaver will fail to activate on its own, or if it activates, it will wake itself up even if I don't move the mouse or press the keyboard.
Any solutions?

Hi Capfred: Thank you for your replay. I have tried to follow your information but unable to solve the problem. I followed your comments but I am unable to get to the menu you mention. I have installed MAC OS X, Version 10.7.2 .
The only thing that works is the Apple last wireless mouse. I belive that I must have done something that created this situation. My problem is that I live in Panama, Central America and the local Apple dealer has little to no tech support.
Would it be possible for me to call you and review the config of these items or is there a way to restore the Macbook Air to the original installation .
I appreciate your kind help and once again thank you for your help. Regards,
Ruben
[email protected]

Wireless Keyboard and Mouse connection lost when computer wakes up

Similar Messages

Maybe you are looking for