Wireless LAN Connection Configuration

Need Basic Wireless LAN Connection Configuration Example

Hi
This link provide WLC configuration examples
http://www.cisco.com/c/en/us/support/wireless/5500-series-wireless-controllers/products-configuration-examples-list.html
Refer config guides if you need step by step guide for all features configurations
HTH
Rasika
*** Pls rate all useful responses ***

Similar Messages

Can some please help me with the Wireless LAN Connection Configuration?

I want to configure WLC in my Testing Lab , need help with the step by step configuration of WLC.

Please go through the below link for the Basic Wireless LAN Connection Configuration Example.
The below link has end – end configuration steps with the images.
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/68005-wlan-connect.html
Have i answered for your query.

Iphone 4 Wireless LAN connection

I have an Iphone 4 and the Actiontec Router.
Recently if I leave my home and then return, my Iphone will connect to the wireless but I am unable to get email or do anything that uses the Internet via the wireless. I have installed a Ping application on my iphone and when I ping the default gateway (192.168.1.1) it times out. When I turn off wireless and then re-enable it works fine.
Additionally if I don't use my phone for sometime it will do the same thing, I cannot get my email unless I disable and re-enable wireless. Anyone experience this problem or know of a work around?
I am using WPA2 AES, 802.11G only and automatic channel selection. I don't have any problems with laptops connected via wireless. I have also tried used Static IP addressing but that didn't do anything either.
Thanks, Jim

yes. It get 192.168.1.5 for example and then DG and DNS of 192.168.1.1
My ping program shows me the IP address of 3G and wireless LAN.
Even if I ping 4.2.2.1 it will time out. If I disable wireless and ping 4.2.2.1 it works. Everything begins to work. Then if I re-enable wireless I can then ping my DG and 4.2.2.1 and get email, etc.
Just seems to happen mostly when I leave for a while then return home.

Wireless Lan connection issue with Linux clients

Hi
In a large Wireless Lan enviroment for a university, we have 3 WISM moduls attached on a 6k hw - Manged by ACS v6.0.181.0
We recently upgraded the software version of the controllers from 4.x to 7.0.98.0 - the Emergency Image version is 5.2.157.0
Since then, the students with Linux clients have massive connection issue - repeated connection lost in a short time period.
However the students with Windows clients have no problem at all.
The studends report, that their linux clients getting so much of some kind of unnecessary broadcast traffic which can not be handled by the NIC - and the NIC goes down - and this happens all 5-10 minutes.
Affected Linux clients are: Ubuntu v10.10 - also OpenSuse, Fedora and Arch-linx with latest OS version.
Any Idea how I could solve this problem?
Thanks in advance for your help

Hi Nicolas
Thanks for your reply. The broadcast forwarding is disabled on WLC's.
Pls find below the attached picture, which shows the captured broadcast traffic on a linux client (sent by a student to me).
I'm not sure, if its really only the broadcast traffic, which the linux clients can not handle.
From my point of view, it seems also to be that the linux clients are somehow disadvantaged among the other clients like windows or mac, if they all trying to get a wireless connection.
But the fact is only the linux clients are affected - and this happens to the linux clients only in our wireless infrastructure.
Windows or Mac clients have no such problem at all
regards
Enis

BT HUB5 Drops wireless & LAN connections 01/01/201...

Hello
Wireless and LAN connections has been working perfectly fine when i first signed up to the complete BT package (broadband,phone,TV) in September 2014. During the beginning of January 2015 to now February 11/02/2015 my wireless connection drops out in the morning and evening multiple times 5am-7am at least 3 times in the morning and at least 5 times at night 6-12. This drop out also affects LAN connections even though the BT HUB 5 is still lit blue, there is no fault light, once or twice I seen the fault light.
I cannot not browse the internet and use Netflix’s etc because the wireless connection drops out regularly. I have spoken to BT’s Global Service Desk who reported there is a problem, however a UK call centre engineer confirms there is no problem and the issue lies with ‘Interference’ and their excuse was it was probably conflicting with other wireless devices which is total nonsense.
I have checked with my neighbours and they have not bought any new devices or changed anything which would conflict with wireless connections, including kitchen appliances. I also have followed BT advise and switch everything off and on again, reset the router back to default, they have reset their end, changed the wireless channel etc. still get the same issues.
Everything has been working fine up until January so something has changed on BT’s end to cause regular problems which affects LAN and Wireless connections. Many sources on the internet suggest firmware and line testing for faults like on their BT HUB5. BT suggest there are no problems and everything is working fine and they have no problems on their end. I’m still waiting for a solution from BT……?; an issue like this would have been resolved or never happened with SKY and Virgin fibre connections.
Please can someone help and adviise best practice to get my BT HUB5 working again properly or suggest what BT must do to pull there fingers out and take ownership of this issue. Many thanks.

Sorry to hijack someone else's thread but I seem to be experiencing exactly the same issue.
Service was installed around about Sept last year and has been fine until the last few weeks when the same wireless drops started to occur. I have no new equipment connected, but all devices experience the problem.
Having looked at my HH5 version, I'm on the same:
BT Home Hub 5 (Type A) | Software version 4.7.5.1.83.8.204 | Last updated 21/01/15
I noticed the update date of 21/1/15 which probably coincides with when the problem started, so I wondered if there might be a known issue with this software version?
Thanks

Satellite P10-873 Wireless LAN Connection

Hi all,
I have a Satellite P10-873 laptop. I've just purchased a Netgear DG834GT wireless modem/router and cannot get fully connected to the internet via Tiscali (ISP).
The problem manifests itself in that I can connect to the router and can even ping various sites on the net. However trying to connect to a site using MSIE I just get "cannot connect" rejection page.
In addition using the CMD prompt, attempting a Telnet session to a web site on port 80 is rejected e.g "www.bt.com 80".
I've set all security to a minimum with no effect.
I have an other notebook which connects and functions perfectly with the Netgear/Ticali setup. I've also identically configured MSIE on both machines without success.
Does anybody have any ideas what could be causing this???
Thanks Mike
[Edited by: admin on 14-Oct-05 11:49]

I have just set up the same router/modem (yesterday). I had a similar problem until I disabled Norton's Personal Firewall. (Windows Firewall already disabled) It then connected and I set up Nortons again afterwards (despite the manual saying do not use 3rd party firewalls. I also need help with my P10-304. I can't get the Intel 2200BG wireless minicard to work. Any ideas?

Wireless LAN Controller Configuration Restore

Hi
Does someone know if i can save the configuration from a 4402 controller and load it into a 4404 controller? Does this work?
regards Dave

By creating a config group, you can group controllers that should have the same mobility group name and similar configuration. You can assign templates to the group and push templates to all the controllers in a group. You can add, delete, or remove config groups, and download software, IDS signatures, or a customized web authentication page to controllers in the selected config groups. You can also save the current configuration to nonvolatile (Flash) memory to controllers in selected config groups.For more info refer the following URL
http://www.cisco.com/en/US/products/ps6305/products_configuration_guide_chapter09186a00806b7277.html#wp1098966

N82 V30.0.013 Bluetooth and Wireless LAN problems

I am using an N82, but it looks like there are similar problems with everything using similar firmware. I didn't have any of these problems with the V20 firmware that came with the phone or after the first V20 upgrade I used.
I find that my wireless LAN connections sometimes only let me browse a few pages before I get the "web connection timed out" message. If I change wireless LAN connection (I have two, mostly for testing purposes) I can continue browsing. Of course the same error may happen causing me to switch again. Sometimes it just works. Both have WPA set up and the passwords are clearly correct. If I use Real Player I can typically listen for as long as I like. Sometimes the connection to the server will drop for Real Player but reconnecting will work (don't have to change wireless LAN network). With the web browser it seems like the data connection is dead, not a server timing out - the message appears instantly. I think have seen the same problem once with my 3G connection, but I haven't recreated it. Could be my imagination!
I have never had any problems with IMAP email using either the Nokia client or Profimail on either the wireless LAN connection or 3G. It leads me to believe that there is nothing wrong with the wireless LAN side of things and it may be more to do with the web browser, or perhaps just that the email clients are only talking to one server helps (DNS problems?). Has anyone experienced similar problems with an alternative browser?
I have also found that when I get to work my bluetooth dongle doesn't connect to my phone. If I disable/enable bluetooth on my phone it will connect. I had this problem with my N80 with the first firmware I had on it and the problem went away after an upgrade.
So, it seems that both connections are fixed by turning them off and on again.

Having both routers the same IP address is a little bit confusing, but possible since each router creates it's own subnet and provides full PNAT support. Actiontec DSL modem has to have DHCP enabled since Linksys WAN (not LAN) port should be connected to one of 4 Actiontec LAN ports. Linksys should not have any configuration setup in regards of your WAN account. Just set it to dynamic address. In ohter words:
1. RJ-11 connect to Actiontec mode/router.
2. Actiontec modem should be configured to acquire an IP address from Verizon and to provide all authentication info to Verizon.
3. Actiontec modem should be configured to allow clients to acquire dynamic IP addresses -- DHCP enabled.
4. Linsys WAN (not LAN!) port should be connected to Actiontec LAN port.
5. Linksys should be configured to acquire dynamic IP address and no authentifacations.
6. Configure Linksys to be DHCP enabled or you can use static IP addresss if you want.
7. Wireless devices would be connected to Linksys and on the way to the Internet addresses would go through double NAT conversions. Any wired device connected to Linksys would have similar features. Any device connected to Linksys should be able to connect 192.168.1.1 assigned to Linksys, but not to Actiontec.
8. To be able to connect Linksys and Actiontec would no be able to communicate unless you split 192.168.1.0/24 into smaller subnets and set specific routes in the table. But even you do so you will not be able to access 192.168.1.1 accross subnets boundary.
Hope it helps.

HP Slate 21 Kit Kat OTA Update Fix for Audio Quality and LAN Connectivity

Recent Over The Air (OTA) update for Slate 21 Update
Link to thread discussion here, fix listed below -
ISSUE:
A previously applied HP Slate 21 Kit Kat Update (Android 4.4.2) over the air (OTA) update may have caused issues with audio quality or wireless LAN connectivity.
Audio Quality: Bass response will be poor. Audio will play but bass frequencies will be lacking.
WiFi Issue: 5 GHz band not functioning properly
Status:
A new update (17r25.1-011-11-WW) has been released over the air (OTA) to end users
Resolution:
Apply update 17r25.1-011-11-WW
If the user was previously on 17r25.1-010-10-WW then a Factory Reset should be performed to complete the resolution.
I work for HP, supporting the HP Experts who volunteer their time and technical knowledge to help others.

Pebbles65,
Thank you for visiting our English HP Support Forum. We are only able to reply to posts written in English. To insure a quick response it would be advisable to post your question in English. The following links are here to assist you if you prefer to post in the following Language Forum.
English: http://h30434.www3.hp.com
Spanish: http://h30467.www3.hp.com
French: http://h30478.www3.hp.com
Portuguese: http://h30487.www3.hp.com
German: http://h30492.www3.hp.com
Korean: http://h30491.www3.hp.com/t5/community/communitypage
Simplified Chinese: http://h30471.www3.hp.com/t5/community/communitypage
Cheers,
KarolB
I work for HP

Ipod break down wireless lan

Hello everybody,
i have a problem with my new iPod touch 4. I have a wireless network with 2 laptops and want to integrate my iPod. When I activate the wireless lan of my iPod and my laptop is on the net, everything is ok. If my laptop isn't on the net and I activate the iPod, the wireless lan breakdown. The Same presiture happens after while when both (iPod and Laptop) are on the net. The only thing what help, is to reboot the router and reset the networksettings of the iPod. Then when the Laptop is again on the net and I enter the wireless lan key for my network in the iPod I am again on with my iPod. But Apps and Music I can't download with my iPod. If I want to do that, I only get the load screen. The samething happens when my Apps want to log in the internet. But Safari works. On my Laptop I have Windows Vista. My Router is a T-Sinus 111 DSL. Has anybody a idea how I can get a firm wireless lan connection on my iPod.
Thanks a lot for the Help

Can't somebody help me? Please I am really despaired

LAN Connections Drop WRT150N

Purchased and installed last Wednesday. Wired and wireless LAN connections have dropped twice since then. Can't access 192.168.1.1 at all, for example.
EasyLink shows message "Different Network Detected". Attempting to use dialogs fails, however, since the router isn't responding.
If I unplug the router, wait, and the restore power, LAN connectivity is restored.
Firmware is up-to-date.
I expect occasional situations like this, but the frequency is troublesome. Any suggestions?
Mark
Message Edited by tcrg311 on 12-15-2007 08:21 AM

I have just got this router yesterday. It did this right out of the box. After an hour or so the connection would just drop. For everything. Some other topic on this site suggested power surges for a similar problem. I moved my power supply to somewhere less crowded and have had continuous internet for about an hour now.
I'll let you know if it worked.
(Edited post for guideline compliance. Thanks!)
Message Edited by JOHNDOE_06 on 12-17-2007 07:15 AM

802.1x on a wired Lan Connection

Dear Community,
i have the job to connect a Windows CE 6.0 device to a Network (wired) with 802.1x. The switch to wich i connect the device is operating as authenticator and the Wince device is the supplicant. A Radius Server with AD is also present .
All the informations and samples that i can find are relating to wireless LAN connections (WZCSVC). A description of the EAPOL API is also absent (or i was not able to find it).
I'm afraid that Wince 6.0 is not prepared for using 802.1x over a wired connection like Win XP can, but i'm not sure about that. I can not find a definite statement whether it is possibe or not.
Does anybody know if it is possible and/or how i can solve this problem.
Regards Achim

Community,
anybody has answer to this problem? I have to do the same thing...
Achim,
did you solve this problem?Thank you
in advance for any help you
can provide.
Regards Bruno

Will 2800-400 BIOS update enable 802.11g wireless LAN?

I recently bought a Belkin 54G cardbus wireless adapter for use with my Satellite 2800-400, which has a Windows ME OS.
The setup software wouldn't install a driver, even though ME was said to be supported.
I wrote to Belkin and they told me that it was because the laptop BIOS didn't support 802.11g wireless and that I should update the BIOS. I updated to BIOS version 2 but it didn't make any difference.
I don't know if Belkin's instructions were on the right track or whether they were they just pushing the responsibility as far away from themselves as they could.
Please can anyone tell me if my laptop does support 802.11g wireless, with or without the BIOS upgrade?
TIA
Mike

> Hi
>
> Im not 100% sure if your notebook supports a
> wireless LAN connection because I dont found any
> informations about it.
Thanks for the reply. the notebook does support wireless LAN because I can get a 802.11b card to function OK.
> But as far as I know its not
> necessary to update the BIOS therewith the Wireless
> card works.
Well it's done now so there may be other benefits. Not 802.11g wireless though it seems.
> I recommend to contact the service partner. They have
> more detailed informations about this unit.
Thanks I'll try to find and contact a service partner.
Mike

Bootcamp Windows 7 Wireless Network Connection: No Valid IP Configuration

I just bought a new 13" MBP and have installed Windows 7 Ultimate via Bootcamp 5.0. I installed the Windows Support Software that I had previously downloaded via Bootcamp Assistant on Mac OS. Although the Wireless Network Connection asked for my network key and connects to the network, I cannot access the internet. The troubleshooter find this problem: "Wireless Network Connection" doesn't have valid IP configuration. I am using my old Dell computer and it is connecting to the wireless properly and my MBP can connect on Mac OS, so I don't think it's a router issue. Here are the things I have tried so far to resolve this issue, but none have worked:
Uninstalling the Broadcom Network Adapter driver, restarting the computer, and reinstalling
Repairing the Windows Support Software with the Bootcamp 5.0.5033 Support Software Update downloaded from www.apple.com
Uninstalling the Broadcom Network Adapter driver, restarting the computer, and reinstalling the driver from Bootcamp 5.0.5033
ipconfig /release gives an error about disconnected media.
ipconfig /all says:
Windows IP Configuration
   Host Name . . . . . . . . . . . . : Alise-PC
   Primary Dns Suffix . . . . . . . :
   Node Type . . . . . . . . . . . . : Hybrid
   IP Routing Enabled. . . . . . . . : No
   WINS Proxy Enabled. . . . . . . . : No
Ethernet adapter Local Area Connection:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet
   Physical Address. . . . . . . . . : 68-5B-35-7C-FC-A9
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
Wireless LAN adapter Wireless Network Connection:
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Broadcom 802.11n Network Adapter
   Physical Address. . . . . . . . . : A8-BB-CF-1B-54-3A
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
   Link-local IPv6 Address . . . . . : fe80::1d6a:752c:62e3:d01b%15(Preferred)
   Autoconfiguration IPv4 Address. . : 169.254.208.27(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.0.0
   Default Gateway . . . . . . . . . :
   DHCPv6 IAID . . . . . . . . . . . : 313048015
   DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-19-C6-A6-83-A8-BB-CF-1B-54-3A
   DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%1
                                       fec0:0:0:ffff::2%1
                                       fec0:0:0:ffff::3%1
   NetBIOS over Tcpip. . . . . . . . : Enabled
Ethernet adapter Bluetooth Network Connection:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Bluetooth Device (Personal Area Network)
   Physical Address. . . . . . . . . : A8-BB-CF-1B-54-3B
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
Tunnel adapter isatap.{C38C3280-5682-4E5A-A978-9DD1A96CDBFF}:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Microsoft ISATAP Adapter
   Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
   DHCP Enabled. . . . . . . . . . . : No
   Autoconfiguration Enabled . . . . : Yes
Tunnel adapter isatap.{ABCE958D-5FDB-4D1E-86F5-ECF01B80E01F}:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Microsoft ISATAP Adapter #2
   Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
   DHCP Enabled. . . . . . . . . . . : No
   Autoconfiguration Enabled . . . . : Yes
Tunnel adapter isatap.{749630EF-9B2E-4DF1-9B6F-B38A5237F81A}:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Microsoft ISATAP Adapter #3
   Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
   DHCP Enabled. . . . . . . . . . . : No
   Autoconfiguration Enabled . . . . : Yes
Please help!

Did you find a solution for this? I have exaclty the same problem.
But I could temporarily solve it by setting an IP, gateway, dns etc manually. But that will only work in my current wifi-network.
I can't even get internet sharing from my iphone

Wireless Lan PCI card Ralink- System Preferences Network Configuration HELP

I just bought a PCI Wireless Lan Card for my G5 tower.
Specifically the card i bought is:
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=220500089785&ssPageName=STRK: MEWNX:IT
It is a Ralink - www.Ralinktech.com
I installed the driver. Both the card and the driver show up in the System Profiler.
BEYOND THIS I AM CLUELESS!

PCI Is at the top of the list. it says NOT CONNECTED next to it. But. Where it says status it says: "STATUS: Cable unplugged" ( and underneath) "The cable for PCI Ethernet Slot 4 is not Plugged In."
What cable??
Configure is set to "Using DHCP"
As i said before. in system profiler it shows up in the correct slot and the driver is installed.
Ralink has its own software that pops up too called WirelessUtilityCardBusPCI. Without me doing anything, my router name shows up on its list so it does recognize it. But connecting to the internet i cannot do nor getting it to come up in System Prefs. Anybody Mess with WirelessUtilityCardBusPCI?

Wireless LAN Connection Configuration

Similar Messages

Maybe you are looking for