Wireless LAN Contoller 2125 IOS upgrade

acustomer has a wireless lan controller 2125 with IOS release 6 we want to upgrade to release 7
what is the best practise for this ?
dose i can extract license and upgrade and put license again ?
i read this decoment it dosenot mentian license of nuer of users :
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00805f381f.shtml

the 21xx does not have a physical license for the number of APs, it is controlled by hardware.  Only the 5508 has a license that needs to be installed.  So you should be good to upgrade to 7.0.

Similar Messages

  • Need some advice for AP IOS upgrade (Wireless Access Point 3702 Series) ?

    Hi to all
    I recently purchase a Wireless Access Point (AIRCAP 3702E-E) with 4 antenna, i will use this device like wifi hotspot in my home.
    I would like to upgrade it but i see two kind of AP IOS :
    Lightweight AP IOS Software
    Autonomous AP IOS
    What are the difference ?
    In case of Lightweight AP IOS Software will be the one to choose, i have multiple IOS :
    Wireless Lan, ap3g2-k9w8-tar.152-4.JB4.tar
    Wireless Lan Recovery, ap3g2-rcvk9w8-tar.152-4.JB4.tar
     Someone can tell me what is the difference between these two versions ?
    Best Regards.
    Elrick.

    Hi Elrick,
    Cisco AP AIRCAP3702E is Cisco enterprise unit.  Cisco small business support WAP4410N, WAP121, WAP321, WAP551, and WAP561 AP. However I will answer your questions.
    Lightweight AP ISO you can use it ONLY if you connect AP to wireless controller
    Autonomous AP ISO for manage and modify AP  by it self not required wireless controller.
    Thanks,
    Moh

  • What are the following:1)Cisco 1600 Series IOS WIRELESS LAN RECOVERY. 2)Service Provider Option 60 for Vendor Class Idenfier

    What are the following:1)Cisco 1600 Series IOS WIRELESS LAN RECOVERY. 2)Service Provider Option 60 for Vendor Class Idenfier
    These items are listed with 1600 series AP but I'm unable to understand what are these things & the use of them

    DHCP Option 60:  Go HERE.

  • Does anyone know if Sprint Wireless will be allowing the hotspot on the devices for free instead of having to pay with the new iOS upgrade?

    Does anyone know if Sprint Wireless will be allowing the hotspot on the devices for free instead of having to pay with the new iOS upgrade?

    Sprint probably knows.  Ask them.

  • Wireless LAN driver upgrade for Portege A100

    My wireless LAN is Atheros AR 5001X+. I keep receiving upgrade notification from Toshiba for Intel Pro Wireless XXXX.
    Can anyone help how to identify wich Intel driver I have to use for my system (Portege A100 with XP Pro)?
    Many thanks

    Hi Max
    I wonder why you want to update the Intel WLan card driver.
    According to your first message you use Atheros AR 5001X+ WLan card and not Intel WLan card. Please dont mix the Intel cards with Atheros cards.
    Ps: if you want to check your Wlan card driver version you have to go to the device manager.
    There you have to select the WLan card and access the properties (right click).

  • X130e wireless lan upgrade to windows 8.1 broken

    Anyone have any luck upgrading the x130e to windows 8.1 ? I am unable to turn the wireless on, the device manager shows that the 1x1 b/g/n wireless lan pci driver is installed correctly. All else upgraded except the WLAN.

    Hi,
    For this issue,since you did a update,I suggest you
    use system restore to return to the point which did
    not appear the problem.
    How to refresh, reset, or restore your PC:
    http://windows.microsoft.com/en-IN/windows-8/restore-refresh-reset-pc
    Hope this helps.
    Regards,
    Kelvin hsu
    TechNet Community Support

  • Software Version Upgrade for Cisco 4402 Wireless Lan Controller

    Hi,
    We have Cisco 4402 Wireless Lan Controller with Software Version 3.2.171.6 and we want to upgrade it to latest version.
    So can anyone please let me know the latest version to upgrade the WLC?
    Also since WLC is running on very lower version is it possible to upgrade to the latest version directly or we have to move it step by step to upgrade this to latest version?
    Thanks

    Take a look at the compatibility matrix below:
    http://www.cisco.com/en/US/docs/wireless/controller/5500/tech_notes/Wireless_Software_Compatibility_Matrix.html
    7.0.235 is the latest that you can go to:
    http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn7_0_235_0.html
    The release notes outline the upgrade process.
    "Upgrade to 4.0.206.0 or later 4.0 release, then upgrade to 4.2.176.0, before upgrading to 7.0.235.0."

  • Cisco 4402 WLC IOS Upgradation using CLI and Web Interface

    Hi,
    I would like to know how to upgrade IOS of Cisco 4402 WireLess LAN Controller using CLI and Web interface ?
    Can any one help me regarding the same.
    Please answer as soon as possible.
    Thanks in advance.

    Here are the instructions for upgrading the controllers via GUI:
    http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn52.html#wp472449
    Instructions via cli:
    Cisco recommends that a direct CLI console port connection is used to update the controller software.
    1. Make sure a TFTP server is available for the Operating System (OS) software download. Also, keep these guidelines in mind when the TFTP server is set up:
    If a download is performed through the service port, the TFTP server must be on the same subnet as the service port because the service port is not routable.
    If a download is performed through the Distribution System (DS) network port, the TFTP server can be on the same or a different subnet because the DS port is routable.
    The TFTP server cannot run on the same computer as the Cisco Wireless Control System (WCS) because WCS and the TFTP server use the same communication port.
    2. Download the desired OS software update file from the Cisco website to the default directory on the TFTP server.
    3. Log into the WLC CLI.
    4. Issue the ping server-ip-address command to verify that the WLC can contact the TFTP server.
    5. Issue the transfer download start command and answer n when prompted to view the current download settings.
    This example shows the command output:
    transfer download start
    Mode........................................... TFTP
    Data Type...................................... Code
    TFTP Server IP.................................
    xxx.xxx.xxx.xxx
    6. TFTP Path...................................... TFTP Filename.................................. AS_2000_3_0_x_x.aes --OR-- AS_4100_3_0_x_x.aes --OR-- AS_4400_3_0_x_x.aes Are you sure you want to start? (y/n) n Transfer Canceled Issue these commands to change the download settings:
    * transfer download mode tftp
    * transfer download datatype code
    * transfer download serverip tftp-server-ip-address
    * transfer download filename filename
    * transfer download path absolute-tftp-server-path-to-file
    Note: All TFTP servers require the full pathname. For example, in Windows, the path is C:\TFTP-Root. (In UNIX forward slashes (/) are required.)
    7. Issue the transfer download start command to view the updated settings, and answer y when prompted to confirm the current download settings and start the OS code download.
    This example shows the download command output:
    transfer download start
    Mode........................................... TFTP
    Data Type...................................... Code
    TFTP Server IP.................................
    xxx.xxx.xxx.xxx
    TFTP Path......................................
    path>
    TFTP Filename..................................
    AS_2000_3_0_x_x.aes --OR--
    AS_4100_3_0_x_x.aes --OR--
    AS_4400_3_0_x_x.aes
    Are you sure you want to start? (y/n) y
    TFTP Code transfer starting.
    TFTP receive complete... extracting components.
    Writing new bootloader to flash.
    Making backup copy of RTOS.
    Writing new RTOS to flash.
    Making backup copy of Code.
    Writing new Code to flash.
    TFTP File transfer operation completed successfully. Please
    restart the switch (reset system) for update to complete.
    8. The WLC now has the code update in active volatile RAM, but the reset system command must be issued to save the code update to non-volatile RAM (NVRAM) and reboot the WLC.
    This is a sample output:
    The system has unsaved changes.
    Would you like to save them now? (y/n) y
    The controller completes the bootup proce

  • Ethernet LAN not working after upgrading to windows 8.1

    After upgrading from Windows 8 to 8.1, my Ethernet LAN is no longer working. Wireless LAN connectivity is OK. I have run the HP Support Assistant and downloaded the drivers for 8.1. Hovever, I do not see a 8.1 driver listed for the Ethernet LAN.

    You're very welcome. See if the recovery manager still works so you can roll back to W8. Please read this guide for how to use it. http://support.hp.com/us-en/document/c03489643 If it doesn't then you will have to order a set of recovery disks from HP, or you can install this plain W8 OEM software this guy has posted on a link. Lots of folks have used it successfully, which is why I posted it. https://docs.google.com/file/d/0B0W9PBigPy94aVJWSndyTFNFMzg/edit?pli=1 Then use this tool to make the iso file bootable to a DVD or 4+ GB USB flash drive. http://www.microsoft.com/en-us/download/windows-usb-dvd-download-tool Yes, that really stinks why you and I could not upgrade without an issue. I disabled about 5 or 6 devices in the device manager and the code 12 would not go away. I have no clue why the PC works fine on W8 but not on W8.1. My notebook is a few years older than yours and it worked fine on W8.1 but not on W10. Go figure...

  • User names from Wireless LAN Controller

    Hi all
    I'm trying to get a report out of a Cisco 4402 Wireless LAN controller, showing all the current clients on a particular WLAN profile, with their user name.
    The Monitor -> Clients screen shows me all the MAC addreses, and I can filter by WLAN Profile Name to home in on the clients I'm interested in.  When I click on a MAC address for more detail, I can see the correctly populated User Name on the Client Properties screen - so the WLC definitely knows all the detail I need...
    Ideally I want spreadheet with a list of usernames of currently connected users (or even better, users that have connected over a time period).  I can't see any way to export this data without doing it manually (and I have 270ish clients at any one time).
    I've tried at the command line, with a "show clients summary", which at least gives me a table I can copy and paste into a spreadsheet, but again the username detail is only displayed with a "show clients detail MACADDRESS" - and the MACADDRESS field won't take a wildcard.
    I've also tried examining the log files, and setting up SysLog to a syslog server - but I haven't observed user names in any of the logs I've seen.
    The WLC is on version 4.2.176.0 - and doing an upgrade isn't very convenient at present - although I might consider taking the pain if a later release provides the funcationaility I need.
    Does anyone have any ideas on this one?
    Thanks!

    Dear Scott,
           I have some points to get clarified for step by step approach that has to be carried out during our downtime, or which is best option for this migration.
    Is that the WLC running different code will be able to join Mobility Group.  i.e. irrespective of Model and Code ?
    1. Do i have to create a mobility group and include the existing WLC and new 3 numbers of WLC , thus when i remove the Existing WLC from the Group the Ap will try to get assosiated with other WLC in the group.
    2. In WCS changing the Access point template configuring primary, secondary , tertiary Wireless LAN controller with New wireless LAN controller, during the down time this activity will be performed.
    Which method or way to proceed during the downtime. Looking for your expert view.
    Thanks .... Arun

  • Nokia N81 reboots when using wireless LAN

    HAs anybody else come across this problem, I have a N81-3 with 8Gb sim card, basically when using wireless lan it reboots, I see there is a firmware upgrade that improves wifi stability but when using the software upgrader it says there are no updates available for my phone, any ideas.??

    The CR-200 only charges at 750mA and I am not even sure that is 100% transferred through the Qi charging. Charging at less than 1A will likely not be enough to keep up with the drain from using the phone while navigating. I think it will use much more than that.
    I use a Anker 13.000 mA battery with my phone while rinding my bike and have had several instances where I accidentally used the 1A output (it has both a 1 and 2 A output) to find that would actually not keep up with the phone running navigation and cycle tracking apps running (in addition to cellular and some other tasks).
    Navigation _will_ require some serious amount sof power and _will_ in general make the phone feel warm to the touch. I very much doubt a wireless charger will be able to provide the juice needed to keep up the charge.
    Click on the blue Star Icon below if my advice has helped you or press the 'Accept As Solution' link if I solved your problem..

  • Go played fine, movie rented night before says "device not authorized"; same thing happened last time I did iOS upgrade

    Rented movies for trip on main computer, synced to iPad, did iOS upgrade  got on plane movie says  "device not authorized"; same thing happened last time I did iOS upgrade; last time apple credited rented movies and told me to rent them again and to not rent & load wirelessly (???).  Don't have main computer with me - how can I get these movies to play for return flight?

    Rented movies for trip on main computer, synced to iPad, did iOS upgrade  got on plane movie says  "device not authorized"; same thing happened last time I did iOS upgrade; last time apple credited rented movies and told me to rent them again and to not rent & load wirelessly (???).  Don't have main computer with me - how can I get these movies to play for return flight?

  • 2851 IOS upgrade failed with WAE

    Hello,
    I have a strange situation with WAAS.  I am in progress of a project to upgrade my Cisco IP telephony and as a result preferred to update my remote sites routers to 12.4.x T code in order to register DSP resources over SCCP and match closely the CMgr version as many of the sites running mainline code didn't have updated parameters for this.  To make a long story short, I upgraded (for other reasons) several non-voice sites routers that have WAE 512s running 4.1.7 with the latest 12.4.xT code and didn't have an issue. All upgraded sites are running 2821's or 2811's except this one site I had an issue with.  I needed T code on this particular site router and assumed since  others sites reacted well with the IOS upgrade and WAAS that this site wouldn't be different but it was!
    Situation:  After updating this 2851 router from 12.4.25c mainline to 12.4.24T3, traffic from WAN was directing to WAE but no return.  It appeared also that any LAN redirection was also working but no return from WAE.  I didn't see any WCCP flow statistics incrementing but traffic was being directed to the WAE.  WAE connection statistics were building but all TCP based traffic was getting dropped.  I tried 3 different feature sets of same code version wondering if I've encountered a bug but none of the featured images worked.  I downgraded to 12.4.24T2 and still nothing.  Changed IOS back to mainline code and WAE was back operational as expected.  During the testing of each IOS change, I've reset the WAE also hoping it didn't get hung up with some WCCP process from the previous IOS change in case there was some codebug occuring.
    Layout:
    With respect to this site, we have a 2851 with multilinked serial interfaces to MPLS; WAN interface is redirecting 62 in with an ACL that disallows a couple of hosts.  LAN side of router is single Gig port (router on a stick).  5 sub-interfaces configured with DOT1Q encap. including one interface for WAAS.  2 of these user interfaces are redirecting 61 in and of course the interface servicing WAAS is redirect excluded in.  The 61 WCCP group is also using ACL to oppositely match WCCP 62 group.
    Why would this upgrade cause a problem especially using latest T code?  Feature sets would be irrelevant.  One more thing that makes this even stranger is I have one other voice site running a 2851 with 12.4.24T3 (already running) and is configured for WCCP the very same with same 512WAE and 4.1.7 code.  The only difference is this router is running a "SP" feature set which I didn't try on this site that is failing.
    Does this make any sense to anyone?  I've seen posted from one of the WAAS experts a document listing compatible IOS version across platforms but these efforts are the latest code.  Any help would be greatly appreciated!  Thanks everyone.

    Thanks Bhavin.
    Sorry, I've been traveling a lot lately for business and I haven't had a chance to respond.  And it looks like I'll be heading out again for a few days.  Meanwhile, I did want to say that I looked at a lot of these things and didn't see anything apparent.  Egress methods show GRE Return.  When I ran "show wccp flows tcp" I didnt' see any flow counts.  However I could see packets redirecting at the router with "show ip wccp".  I debugged events and packets and saw "See You" packets being sent back to the caching appliance.  WCCP looked fine from the router's viewpoint.  WCCP communications looked good rather.  But anything getting redirected to the WAE would get dropped.
    I don't have a chance right now to change IOS back to one of the non-working versions to get all of the info. but I will try soon.  Unfortunately, the site is where my executives reside and it's always a tough situation to do anything there most of the time.
    And to answer your question about having another configuration in place working .... yes I do.  I have another 2851 with 12.4(24)T3, same WAE model with WAE-4.1.7 code and everything configured the same including connections as the site that isn't working.  The only difference as mentioned before is that this working site router is running SP feature set which I know shouldn't matter but I didn't try a SP feature set however I went through ADV IP, ADV ENTER, and IP VOICE and neither worked with 2 different 12.4(X)Tx versions.  I was grasping at straws at this point.
    I figured I was going to need to get TAC involved when I could spare some time to run one of the non-working IOS images and could afford to not have WAAS working for the site but was hoping one of you guys might have seen something like this and could offer something to try to fix the issue.  It is very odd indeed.  I have other 28xx routers and all of the upgrades worked that aren't 2851's.
    I'll post more info. when I can.
    Thanks again!
    Wayne

  • N82 V30.0.013 Bluetooth and Wireless LAN problems

    I am using an N82, but it looks like there are similar problems with everything using similar firmware. I didn't have any of these problems with the V20 firmware that came with the phone or after the first V20 upgrade I used.
    I find that my wireless LAN connections sometimes only let me browse a few pages before I get the "web connection timed out" message. If I change wireless LAN connection (I have two, mostly for testing purposes) I can continue browsing. Of course the same error may happen causing me to switch again. Sometimes it just works. Both have WPA set up and the passwords are clearly correct. If I use Real Player I can typically listen for as long as I like. Sometimes the connection to the server will drop for Real Player but reconnecting will work (don't have to change wireless LAN network). With the web browser it seems like the data connection is dead, not a server timing out - the message appears instantly. I think have seen the same problem once with my 3G connection, but I haven't recreated it. Could be my imagination!
    I have never had any problems with IMAP email using either the Nokia client or Profimail on either the wireless LAN connection or 3G. It leads me to believe that there is nothing wrong with the wireless LAN side of things and it may be more to do with the web browser, or perhaps just that the email clients are only talking to one server helps (DNS problems?). Has anyone experienced similar problems with an alternative browser?
    I have also found that when I get to work my bluetooth dongle doesn't connect to my phone. If I disable/enable bluetooth on my phone it will connect. I had this problem with my N80 with the first firmware I had on it and the problem went away after an upgrade.
    So, it seems that both connections are fixed by turning them off and on again.

    Having both routers the same IP address is a little bit confusing, but possible since each router creates it's own subnet and provides full PNAT support. Actiontec DSL modem has to have DHCP enabled since Linksys WAN (not LAN) port should be connected to one of 4 Actiontec LAN ports. Linksys should not have any configuration setup in regards of your WAN account. Just set it to dynamic address. In ohter words:
    1. RJ-11 connect to Actiontec mode/router.
    2. Actiontec modem should be configured to acquire an IP address from Verizon and to provide all authentication info to Verizon.
    3. Actiontec modem should be configured to allow clients to acquire dynamic IP addresses -- DHCP enabled.
    4. Linsys WAN (not LAN!) port should be connected to Actiontec LAN port.
    5. Linksys should be configured to acquire dynamic IP address and no authentifacations.
    6. Configure Linksys to be DHCP enabled or you can use static IP addresss if you want.
    7. Wireless devices would be connected to Linksys and on the way to the Internet addresses would go through double NAT conversions. Any wired device connected to Linksys would have similar  features. Any device connected to Linksys should be able to connect 192.168.1.1 assigned to Linksys, but not to Actiontec.
    8. To be able to connect Linksys and Actiontec would no be able to communicate unless you split 192.168.1.0/24 into smaller subnets and set specific routes in the table. But even you do so you will not be able to access 192.168.1.1 accross subnets boundary.
    Hope it helps.

  • Need Wireless lan card for L100-179

    Hi guys can any one advise me where to buy a wireless lan card and any advise and installing one please

    Hello
    In my opinion the first step is your local dealer where you have bought the unit. This unit is not known to me but I presume unit is WLAN ready and upgrade with mini PCI WLAN card is possible.
    Other way to find out which WLAN card is compatible with your unit is to contact service partner in your country.

Maybe you are looking for