Wireless LAN Controller not broadcasting network to Access points

Good Day Team,
I am working with a 2100 series WLC controller and 1100 series access point.
I noticed that the wireless lan controller is working. Also the access point is working.
The issue is that there is no internet connection on the access point.
What could be the error?
Kindly advice

Try do diagnose your problem following this steps:
1) Connect to the wireless network
2) Check your IP address with "ifconfig"
3) Check if your gateway is set correctly with "route -n"
4) Try to ping your gateway. Is it working?
5) Try to ping an internet IP like google: "ping 74.125.234.115"
6) Try to resolve names with "nslookup www.google.com" for example.
7) Try to traceroute to an IP or name on internet. Check the result to see the last hop you reached.
8) If you passed all those tests, try this: "telnet www.google.com 80"
If everything works, but not the test #8, your problem could be related to some proxy configuration.

Similar Messages

  • AIR-CAP3501I access point not joining the Cisco 2100 Wireless Lan controller.

    Hello All,
    I am installing a new LAP (AIR-CAP3501I ) through the wireless lan controller (AIR-WLC2112-K9) with software version 7.0. I have an external ADSL modem which will act as the DHCP server for the wireless clients and the LAP.
    Please find my network setup as below:
    The ISP ADSL modem , WLC and LAP are connected to a unmanaged POE switch. The LAP gets its power through the POE switch. When i connect the LAP and the WLC to the switch along with the ADSL modem, the LAPs are getting the ip address from the ADSL modem, however they are not joining the WLC for further process.
    ADSL Modem ip address: 192.168.1.254
    Management ip address on the LAP: 192.168.1.1 ( Assigned to port 1, untagged Vlan).
    Ap Manager ip address: 192.168.1.1 ( Assigned to the same port i.e port1, Untagged Vlan).
    The LAP is getting an IP address from the ADSL modem in the range of the DHCP scope.
    I will paste the logs very soon.
    Please let me know if i am doing anything wrong oe what will be the issue.
    Thanks in advance,
    Mohammed Ameen

    Hello All,
    Please find the logs for  "debug capwap event" from the WLC below:
    *spamReceiveTask: Sep 26 19:44:59.196: e8:04:62:0a:3f:10 Join Version: = 117465600
    *spamReceiveTask: Sep 26 19:44:59.197: e8:04:62:0a:3f:10 Join resp: CAPWAP Maximum Msg element len = 92
    *spamReceiveTask: Sep 26 19:44:59.197: e8:04:62:0a:3f:10 Join Response sent to 192.168.1.156:45510
    *spamReceiveTask: Sep 26 19:44:59.197: e8:04:62:0a:3f:10 CAPWAP State: Join
    *spamReceiveTask: Sep 26 19:44:59.197: e8:04:62:0a:3f:10 capwap_ac_platform.c:1216 - Operation State 0 ===> 4
    *apfReceiveTask: Sep 26 19:44:59.198: e8:04:62:0a:3f:10 Register LWAPP event for AP e8:04:62:0a:3f:10 slot 0
    *spamReceiveTask: Sep 26 19:44:59.341: e8:04:62:0a:d1:20 DTLS connection not found, creating new connection for 192:168:1:158 (45644) 192:168:1:2 (5246)
    *spamReceiveTask: Sep 26 19:45:00.119: e8:04:62:0a:d1:20 DTLS Session established server (192.168.1.2:5246), client (192.168.1.158:45644)
    *spamReceiveTask: Sep 26 19:45:00.119: e8:04:62:0a:d1:20 Starting wait join timer for AP: 192.168.1.158:45644
    *spamReceiveTask: Sep 26 19:45:00.121: e8:04:62:0a:d1:20 Join Request from 192.168.1.158:45644
    *spamReceiveTask: Sep 26 19:45:00.123: e8:04:62:0a:d1:20 Join Version: = 117465600
    *spamReceiveTask: Sep 26 19:45:00.123: e8:04:62:0a:d1:20 Join resp: CAPWAP Maximum Msg element len = 92
    *spamReceiveTask: Sep 26 19:45:00.124: e8:04:62:0a:d1:20 Join Response sent to 192.168.1.158:45644
    *spamReceiveTask: Sep 26 19:45:00.124: e8:04:62:0a:d1:20 CAPWAP State: Join
    *spamReceiveTask: Sep 26 19:45:00.124: e8:04:62:0a:d1:20 capwap_ac_platform.c:1216 - Operation State 0 ===> 4
    *apfReceiveTask: Sep 26 19:45:00.125: e8:04:62:0a:d1:20 Register LWAPP event for AP e8:04:62:0a:d1:20 slot 0
    *spamReceiveTask: Sep 26 19:45:00.273: e8:04:62:0a:d1:20 Configuration Status from 192.168.1.158:45644
    *spamReceiveTask: Sep 26 19:45:00.273: e8:04:62:0a:d1:20 CAPWAP State: Configure
    *spamReceiveTask: Sep 26 19:45:00.273: Invalid channel 1 spacified for the AP APf866.f2ab.24b6, slotId = 0
    *spamReceiveTask: Sep 26 19:45:00.274: e8:04:62:0a:d1:20 Updating IP info for AP e8:04:62:0a:d1:20 -- static 0, 192.168.1.158/255.255.255.0, gtw 192.168.1.254
    *spamReceiveTask: Sep 26 19:45:00.274: e8:04:62:0a:d1:20 Updating IP 192.168.1.158 ===> 192.168.1.158 for AP e8:04:62:0a:d1:20
    *spamReceiveTask: Sep 26 19:45:00.274: e8:04:62:0a:d1:20 Setting MTU to 1485
    *spamReceiveTask: Sep 26 19:45:00.274: e8:04:62:0a:d1:20 Finding DTLS connection to delete for AP (192:168:1:158/45644)
    *spamReceiveTask: Sep 26 19:45:00.274: e8:04:62:0a:d1:20 Disconnecting DTLS Capwap-Ctrl session 0xa06d6a4 for AP (192:168:1:158/45644)
    *spamReceiveTask: Sep 26 19:45:00.274: e8:04:62:0a:d1:20 CAPWAP State: Dtls tear down
    *spamReceiveTask: Sep 26 19:45:00.277: spamProcessGlobalPathMtuUpdate: Changing Global LRAD MTU to 576
    *spamReceiveTask: Sep 26 19:45:00.277: e8:04:62:0a:d1:20 DTLS connection closed event receivedserver (192:168:1:2/5246) client 192:168:1:158/45644).
    The Acess point joins the Controller for 2-3 seconds and then unjoins again. I am not sure what i am doing wrong here. The access points are getting the IPs from the ADSL modem through the switch, then it talks to the WLC, however it does not join the controller for further process.
    Note:
    The Managemnet interface and the AP manager interface are assigned to the same port 1 with unassigned Vlan as mention above.

  • Warning page on Cisco Wireless Lan Controller for guest access

    Hi,
    We have an Cisco wireless LAN controller 4400 in our organization, and lots of guest using our Wi-Fi network.
    I would like to configure a warning and terms and condition page when guest using first time our network.
    Can you please let me know is that possible without adding external web server and how to configure.
    Many Thanks in Advance
    Amit Sharma

    Hi Amit,
    Hope you are doing great!!
    the below link will help you in getting the issue resolved!!
    http://www.cisco.com/en/US/products/ps6366/products_configuration_example09186a00809bdb5f.shtml
    Please dont forget to rate the usefull posts!!
    Regards
    Surendra

  • Cisco Wireless Control System need wireless Lan Controller ?

    Cisco Wireless Control System need wireless Lan Controller , for Rogue detection

    Hi Joao,
    The WCS is used in conjuntion with the WLC (Wireless Lan Controller) for Rogue Detection. It is not a must for this function but more of an add-on :)
    The Cisco WCS is an optional network component that works in conjunction with Cisco Aironet Lightweight Access Points, Cisco wireless LAN controllers and the Cisco Wireless Location Appliance.
    From this doc;
    http://www.cisco.com/en/US/products/ps6305/index.html
    Overview of WCS
    The Cisco Wireless Control System (WCS) is a Cisco Unified Wireless Network Solution management tool that adds to the capabilities of the web user interface and command line interface (CLI), moving from individual controllers to a network of controllers. WCS includes the same configuration, performance monitoring, security, fault management, and accounting options used at the controller level and adds a graphical view of multiple controllers and managed access points.
    WCS runs on Windows 2003 and Red Hat Enterprise Linux ES 4.0 and AS 4.0 servers. On both Windows and Linux, WCS can run as a normal application or as a service, which runs continuously and resumes running after a reboot.
    The WCS user interface enables operators to control all permitted Cisco Unified Wireless Network Solution configuration, monitoring, and control functions through Internet Explorer 6.0 or later. Operator permissions are defined by the administrator using the WCS user interface Administration menu, which enables the administrator to manage user accounts and schedule periodic maintenance tasks.
    WCS simplifies controller configuration and monitoring while reducing data entry errors with the Cisco Unified Wireless Network Controller autodiscovery algorithm. WCS uses the industry-standard SNMP protocol to communicate with the controllers.
    From this good doc;
    http://www.cisco.com/en/US/products/ps6305/products_configuration_guide_chapter09186a00806b7270.html#wp1131195
    Detect and Locate Rogue Access Points
    From this WCS doc;
    http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a00806f070a.shtml#new5
    Rogue Detection under Unified Wireless Networks
    http://www.cisco.com/en/US/tech/tk722/tk809/technologies_white_paper09186a0080722d8c.shtml
    Hope this helps!
    Rob

  • Issues after changing the AP Name on Wireless LAN Controller

    I recently changed the AP Name of all the Wireless Access Points in my branch office (which are all associated to the branch office Wireless LAN Controller(s)). After that I noticed that all branch office employees are unable to connect to the employee SSID. The employee SSID uses web authentication and employees are authenticated using Head Office AD via Cisco ACS, both located at the Head Office.
    There are other SSID's on the WLC which all work fine, but only employee SSID which uses AD authentication does not work. AD authenticaion is working fine because employee's in HO are successfully able to connect to the employee SSID at HO.
    The branch office is connected to the HO via a tunnel link. We noticed that if we restart both the ASA at either ends of the tunnel. The employee SSID starts working again but only temporarily for a day or so... what could be the issue? Can renaming the AP's cause issues? How can I fix this problem?
    Thanks in advance

    Thanks Elliott,
            I did the debug like you said and I am getting the following debug messages:
    *apfMsConnTask_0: Jun 20 08:18:14.580: Deleting the client immediatly since WLAN is changed
    and also
    *apfReceiveTask: Jun 20 05:25:11.857: 00:1f:3c:86:af:15 Orphan Packet from 192.168.52.34
    The logging on the WLC shows
    *apfReceiveTask: Jun 18 17:56:41.788: %MM-1-ANCHOR_UNAVAILABLE: mm_mobile.c:2155
    All export anchors are down. Cannot anchor the client.00:c0:a8:f3:cd:ae
    The DHCP pool for the employee users are configured on a guest WLC which sits behind an ASA

  • How to replace the certificate of Cisco 2106 wireless LAN controller for CAPWAP ?

    I have interested in CAPWAP feature and I download the open capwap project to make Access Controller (AC) and Wireless Terminal Point (WTP). I had built the AC which used PC and WTP which used Atheros AP. The CAPWAP feature work well when I enabled the CAPWAP that used my own AC  and WTP. When I got the Cisco 2106 wireless LAN controller (Cisco WLC), I configured the Cisco WLC to instead my own AC but I got the authorize fail in Cisco WLC side. It seem the Cisco WLC could not recognize the CAPWAP message which sent form my own WTP. I think this issue just need to synchronize the certificate between Cisco WLC and WTP.So I need to replace the Cisco WLC's certificate manually. Does anyone know how to replace the certificate manually with Cisco WLC ?
    Best Regards,
    Alan

    Unfortunately this Support Community is for Cisco Small Business & Small Business Pro product offerings.  The WLC2106 is a traditional Cisco product.  You can find this type of support on the Cisco NetPro Forum for all traditional Cisco products.
    Best Regards,
    Glenn

  • Wireless lan Controller 4402 / ping dynamic interface failed

    hi,
    i've a problem with a Wireless Lan Controller 4402.
    When i configure the dynamic interface on the my network , with wired lan
    i don't reach (i use the ping command) the ip address of the WLC.
    In my case (wired):
    On my pc i've a ip 10.1.78.1 255.255.0.0 and dgw 10.1.1.1 (vlan721)
    The lan WLC have a ip of management 10.12.2.4 /24 (vlan799) [dgw 10.12.2.1]
    dynamic vlan 792 ip add 10.12.78.100 / 22 (vlan792) [dgw 10.12.68.1]
    i ping these interfaces (10.12.2.4 and 10.12.78.100) and the ping is ok.
    When i create a dynamic interface vlan 721 starting the problem:
    dynamic vlan 791 ip address 10.1.1.240 / 16 (vlan721)
    After this ......the ping on 10.12.2.4 and 10.12.78.100 don't respond very well
    and i lose the 80-90% of the ping packages.
    through the wi-fi instead I do not have problems.
    the problem exist only via wired (cable).
    Can you help me?
    Thanks
    FCostalunga

    Hello,
    Pinging the dynamic interface is officially not supported. The reason why is because the controller places a very low priority on ICMP traffic. Typically, you will not have an issue with doing so on your wireless network because this interface is basically a gateway for the client. However, from the wired network - the only interface designed to respond to pings 100% of the time is the management interface. Hope this helps!
    -Mark

  • Is it possible run a Wireless LAN controller without a WCS?

    is it possible run a Wireless LAN controller without a WCS?
    How Can I configure the Wireless Lan controller?
    Thanks

    Hi Alfred,
    The WLC can be completly configured and operated without the WCS. The WCS is a nice addition for the management especially when running multiple WLC's but is not required.
    Info on WLC (with Video);
    http://www.cisco.com/en/US/products/ps6366/index.html
    Info on the WCS;
    http://www.cisco.com/en/US/products/ps6305/index.html
    Hope this helps!
    Rob

  • Cisco Wireless LAN Controller Always disconnect

    Dear All,
    Please help to assist my issue.I used Cisco Wireless LAN Controller model: 5508 with version 7.0.98.0 and I got issue with connection always disconnect ping always loss or some time client can't get DHCP from Controller. 
    - I configure as Internal DHCP Server with 1 SSID.
    http://www.cisco.com/c/en/us/support/docs/wireless/4400-series-wireless-lan-controllers/110865-dhcp-wlc.html
    - DHCP least is not full and I also try to clear-lease all but still not work.

    1. Config dhcp proxy enable
    2. In case of internal Dhcp, try debug for clients
     using,
    debug client <MAC ADDRESS OF CLIENT>

  • 4404 wireless lan controller managment via wireless clients

    I am having an issue managing a 4404 wireless lan controller via wireless clients.
    I have checked the box "enable controller management to be accessible from wireless clients" under management. For some reason that does not seem to fix the problem (page cannot be displayed). I cannot ping the controller by IP but other devices on the same subnet respond. Everything else works fine.
    I CAN manage the controller when plugged in a wired connection.
    When I do a route print it is identical wireless or wired. The route simple points to my interface. If I modify the route on my computer to actually point to our gateway instead of the interface then everything works. But why should I have to do this only for my wireless connection and not my wired to manage this box?

    Thanks for the info. I narrowed the problem down to an ARP issue.
    In order for me to connect to the controller, I run a batch file that creates a static ARP entry on my laptop. I don't have to do this for any other device except the controller. Not sure what the underlying cause is, but that works as a workaround right now.

  • Wireless Lan Controller Issue

    Hi All,
    We have a Wireless Lan Controller 4402 with software version 4.0.155.5. On Friday we experience a problem where our clients wouldn't get redirected to the internal webpage for authentication. It would just come up with page not found. We know the page was working fine becasue we could manually type in the
    https://1.1.1.1/login.html and the
    page would come up and you could login successfully. The users who were already connected to the controller were not affected and continued to operate. We have 2 other WLC's at the same software revision and they were not affected so I don't think it has anything to to with software level. Its like the webserver in the wlc failed to work. We failed over the AP's to the 3rd WLC and rebooted WLC1. After the WLC1 restarted we failed one of the previous non-working AP's back to it and it works again.
    I know "now" there is debug commands to run at the time when the WLC wasn't working, but unfortunately I didn't know at the time. The WLC is running again fine and I was wondering if anybody has seen this issue before.
    Any ideas on a fix or reason would be greatly appreciated.
    Thanks,

    We are running WiSM 4.1.185.0 and we just had the similar problem with one controller. The other three controllers were fine when it happened. The exactly issue was the nslookup failed(timed out) from the client, so the web login page won't show when people lunch the browser. A reboot of the controller fixed the problem. We have been running Cisco LWAPP for more than a year (from 4.0.155.5 to 4.1.185.0) and it is the first time we see this problem. TAC is still investigating the cause.
    Zhenning

  • User names from Wireless LAN Controller

    Hi all
    I'm trying to get a report out of a Cisco 4402 Wireless LAN controller, showing all the current clients on a particular WLAN profile, with their user name.
    The Monitor -> Clients screen shows me all the MAC addreses, and I can filter by WLAN Profile Name to home in on the clients I'm interested in.  When I click on a MAC address for more detail, I can see the correctly populated User Name on the Client Properties screen - so the WLC definitely knows all the detail I need...
    Ideally I want spreadheet with a list of usernames of currently connected users (or even better, users that have connected over a time period).  I can't see any way to export this data without doing it manually (and I have 270ish clients at any one time).
    I've tried at the command line, with a "show clients summary", which at least gives me a table I can copy and paste into a spreadsheet, but again the username detail is only displayed with a "show clients detail MACADDRESS" - and the MACADDRESS field won't take a wildcard.
    I've also tried examining the log files, and setting up SysLog to a syslog server - but I haven't observed user names in any of the logs I've seen.
    The WLC is on version 4.2.176.0 - and doing an upgrade isn't very convenient at present - although I might consider taking the pain if a later release provides the funcationaility I need.
    Does anyone have any ideas on this one?
    Thanks!

    Dear Scott,
           I have some points to get clarified for step by step approach that has to be carried out during our downtime, or which is best option for this migration.
    Is that the WLC running different code will be able to join Mobility Group.  i.e. irrespective of Model and Code ?
    1. Do i have to create a mobility group and include the existing WLC and new 3 numbers of WLC , thus when i remove the Existing WLC from the Group the Ap will try to get assosiated with other WLC in the group.
    2. In WCS changing the Access point template configuring primary, secondary , tertiary Wireless LAN controller with New wireless LAN controller, during the down time this activity will be performed.
    Which method or way to proceed during the downtime. Looking for your expert view.
    Thanks .... Arun

  • Ise 1.1.1 missing Wireless LAN Controller (WLC) in Auth Profile

    Anyone else not seeing the Wireless LAN Controller tick box in Authorization Profile?
    Clean install of 1.1.1. with ISE Version 1.1.1.268—Cumulative Patch 1 applied
    EVAL license
    All the documentation says it should still be there in 1.1.1 unless im missing a trick?

    If you are referring to the ACL for the wireless lan controller that has change to the "Airespace ACL Name".
    This looks like a documentation bug.
    Tarik Admani
    *Please rate helpful posts*

  • Wireless lan controller

    Hello,
    In our company we have a cisco wireless lan controller. the managemant interface (untagged 192.168.10.240) is able to ping to all te vlan's. When i add a interface (for example vlan 20 voice 192.168.20.240 255.255.255.0 192.168.20.254) i cant ping that network anymore from my controller while the ip and vlan configurations are good. Can someone help me to solve this problem?

    Because you have more than one VLAN, you need to TAG the uplink.  On the switch you need to enable Dot1Q Trunking and allow the required VLAN.

  • Can cisco CAP2702i connect to Cisco3850 switch with wireless LAN controller license via another switch ?

    If i connect cisco AP - CAP2702i to another switch, and use trunk port between Cisco3850 and the other switch , can the AP able to register with Cisco3850 with wireless LAN controller  ?   or the AP has to directly connect to Cisco3850 in order to register?

    The AP and 3850 wireless management are in same Vlan( vlan202). The AP is new unit and did not join MC before. 
    What i did on 3850 :
    input command - wireless management interface vlan 202
                              - ap cdp
                              - wireless mobility controller
    Is there any config i miss out on 3850 and any config need to be set on AP ?
    From Ap console output show me "could not discover WLC using dhcp ip". Is it due to AP dont have IP address? If AP register with WLC through layer 2 , i believe there is no related with IP.Correct me if i'm wrong.
    Due to the 3850 is not a POE, the AP unable directly connect to 3850  . I guess have to use power adapter to power on the AP.

Maybe you are looking for

  • How can I share notes from iPhone to MaCbook

    I can't share my notes from my iPhone to my MacBook. How do you do that?

  • Slow Macbook pro - etrecheck report

    Hi, My macbook pro is slowing down. I download torrents, think this may have caused it. As suggested in some other forums I ran etrecheck and the report here as follows. Any help to improve the speed is much appreciated. Thanks in advance. EtreCheck

  • Yet another kernel panic...

    Until I upgraded to Mountain Lion, I had never heard of a kernel panic, much less experienced one, much less several times a week. There's no predicting when one will happen; sometimes I go for days with no panic, then there are a couple a day. I too

  • Add months do Presentation variable

    I do have a Pres.Variable in a date format - like: DD/MM/YYYY. I need to use it as a filter... when using @{VAR} is ok... Now I need to filter another column but using @{VAR} next month... Tried to use TIMESTAMPADD with @{VAR} but no success... maybe

  • What kind of modem is in a Nokia N82

    I would like to find out what type of a modem is in nokia N82. My question is based on the following: I have been using my Dell laptop as a recording and answering maching for my voice calls using a landline. I had been connecting my phone line thoro