Wireless Module Not Supported...in the manual it is?
HP maual located here: http://h10032.www1.hp.com/ctg/Manual/c02770268.pdf
Page 20 Chapter 3 it lists:
Intel Centrino® Wireless-N 1000 (802.11b/g/n) 593530-001
So I ordered this from the HP parts store and received it today and the laptop posts with a Wireless Module Not Supported. WLAN Module ID 702 message.
So how do I proceed from here? Laptop came with an ralink card that only connected at 72Mbps, the atheros AR9285 constantly connects at 65Mbps unless I reset my router every time I connect.
My laptop is a HP Pavilion g6-1a40ca
Help please!
Marc
Thanks for replying
Looks like modding the bios is the only way I'll get something better into this laptop. All I know is that the two officially supported cards I have right here are terribly slow/flaky. Going by the manual I really don't have any other choice in wireless cards. This is a great laptop for the price, just wish it didn't come crippled.
Oh I know...lol...I'll buy a usb one and soldier it onto one of the usb ports internally. j/k
Thanks again for clarifying for me. If anyone has anything additional to add to this thread in future about adding support official or unofficial, please post it here.
Thanks,
Marc
Similar Messages
-
I have a DV6Z-6C00 CTO laptop notbook and I recently had to install a new wireless card but I keep getting a Wireless module not supported error. I checked with the manual and I ordered a Intel Centrino-N 1000 WLAN Module (593530-001 replacement #) and I checked on the actual card (and they match). So why am I getting this error, and how can I fix it?
Btw I have Windows 8Is the wireless card an actual HP card? It is not enough that it be the same Intel chipset card.
-
When I publish a SWF/HTML5 module with Captivate 8 and try to run it using IE9 - I get the following error "The content you are viewing is not supported in the current Document Mode" - anyone know why?
TLCMediaDesign wrote:
I've seen a lot of threads about getting rid of these kind of messages. Those messages are there for a reason most of the time. If you have CSS animations or other HTML5 standards that cannot be rendered in IE9 they won't magically start working becuse you got rid of a message. I use IE9 since that is the minimum standard for the client. I have never seen that message publishing to HTML5 content.
IMO, if your client has IE9 I think that you should develop with IE9 in mind not IE11.
When you say "develop with IE9 in mind not IE11" do you mean use SWF instead of HTML5? I used the standard question types, and a converted PowerPoint presentation. I didn't add anything out of the ordinary. -
Xtreme Gamer is "not Supported by the Application" Problem. He
My SoundBlaster XFi Xtreme Gamer has suddenly stopping being detected by my creative software, such as Volume Panel. The drivers are installed, and when I hover my mouse pointer over the volume panel is still shows "SB X-Fi Audo [E000]" which is the sound card, but when I doubled click to open the volume panel it says that "The current selected audio device is not supported by the application. Do you want to select another audio device now?". When I click "Yes", it doesn't show anything on list besides "Windows Default Audio". This happened out of no wheres, with no changes at all to my computer. Volume Panel was working yesterday, but when I woke up today it wasn't. I have no idea what could be causing this, or what caused it... I did update the drivers about a week ago, but it was all working fine since, until today.
I haven't installed or uninstalled anything since it was working properly.
I tried reinstalling drivers and software, and it did not fix anything. I also uninstalled everything including drivers from computer, and used my original installation CD to install everything over again. Every installed fine, but then for some reason it would not install the drivers. Windows was detecting the device, but when I went to install the hardware manually, it would ask for CD to find some files to install... it said this twice, I located the files it needed, and each time it would complete the process it would instantly reboot computer without notice. When the computer was booted up, it would ask then ask again for the Creative CD to install the detected hardware. So I for awhile I could not install the drivers, but for some reason out of no wheres it finally installed when I used the update installation file I downloaded from Creative.com, even though I had tried the same thing a few times, it for some reason installed drivers. But now it is all installed again, my software seems imcomplete and will still not work with the sound device. What seems to be the problem here? Only thing I can think of now is the installation for some reason became corrupted. Only way I can think of fixing it is reformatting my whole computer, but as of right now I don't feel like spending a whole day doing so.
Is there anything that you can think of to fix this problem? I have had the sound card for about a year now. As of right now, I am still using headphones in the soundcard, but it doesn't sound good at all as I can't change anything in software. I also noticed that is no longer has as much installed as it would if I used my original CD. It doesn't have an option to switch sound modes anymore. It also doesn't now have "X-Fi Soundblaster" in "Add/Remove Programs" list. All it has in Add/Remove is "Creative Audo Console".
I uninstalled everything I could and deleted left over files in the Creative directory, so I deleted the whole folder after.
Only other thing I can think of is something in the registery is messed up, and causing the sound card not to be recognized. I also have WinXP SP2.I spent yet another hour or two trying to fix it, and nothing changed.
I put it into a different PCI slot, and made no difference.
PCI slot doesn't seem to be the problem, I am thinking it is something within the registry itself.
I also put in the CD and there was no option to remove drivers, so I just went ahead and tried overwriting them, but that actually made things worse. My computer kept rebooting over and over when it hit the Windows Boot Up logo, and had to go into safe mode and do a system restore to get it back to normal.
It also keeps asking for the CD when windows loads and it detects the soundcard.
It will ask to locate acouple files, I do what it it says, but just as it is finishing installing the drivers it reboots the system.... when windows is loaded again, it will ask the same thing over, and will keep giving same results.
There isn't anything to completely remove all the creative files and folders including the 00's of registry keys. Maybe Driver Sweeper or Driver Cleaner Pro might help? ill try them, but as of now im not bothering with the soundcard.... ill just reformat. I just hope it ain't the card itself, because I am a month over the one year warranty, and the azzholes from creative said there was nothing they can do about it.
That alone made me want to turn to a different brand next time with better support. Creative has some of the worst support I know of.
They tend to leave people hanging with their defecti've hardware. What I don't get is, that the card still installs the drivers at times, and it will still work but the software won't.
I have been using it this whole time, but seems to freeze up my Guildwars alot.
It still sounds good, way better than Onboard, just not as good as before because there were no options for change mode, or couldn't access the equalizer.
Anyone know of any programs that will completely remove everything for the Xtreme Gamer Creative Software? Including everything in registry.
Also, is it possible that there might be a Windows Service that might have an effect on the problem? I tried enabling a few things, then try rebootin and reinstalling, but didn't seem to help.
But then again, I am not sure which services would cause the problem.
Definately something happened with the last Creative Driver update, only took a week afterwards for something to go wrong. -
Wireless module not working(701)
Hello, i recently formatted my laptop and then i found that at startup my laptop is saying Wireless module not found(701)
It says it may be not installed correctly or not functioning.
So i disassembled my laptop to see any connection problem and tried connecting with changing positions of wires with card but still not working!
I Googled for drivers but didnt geta any!
here is detail about Wlan + Bt card
AzureWave AW-NB041H
IEEE 802.11 b/g/n + 802.15 BT combo card
Model No.-RT3090BC4
FCC ID- VQF-RT3090BC4
IC-7542A-RT3090BC4
India-448/2010/WRLO
CMIIT ID- 2010DJ0636
Please help to me to solve this problem!
This question was solved.
View Solution.It needs to be replaced. This one will work in your netbook. It will pass the whitelist BIOS check and provides wifi and Bluetooth:
http://www.ebay.in/itm/HP-WI-FI-BLUETOOTH-COMBO-CARD-BCM94313HMGB-600370-001-598711-001-G6-CQ42-/321...
If this is "the Answer" please click "Accept as Solution" to help others find it. -
VWIC is showing as "WIC module not supported/disabled in this slot"
Hello All,
please help me on this asap!!
Smart Init is enabled
smart init is sizing iomem
TYPE MEMORY_REQ
HWIC Slot 0 0x00200000
PVDM 0 0x00200000
Onboard devices &
buffer pools 0x0228F000
TOTAL: 0x0268F000
Rounded IOMEM up to: 40Mb.
Using 7 percent iomem. [40Mb/512Mb]
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(1)T, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Mon 22-Mar-10 02:13 by prod_rel_team
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco CISCO2901/K9 (revision 1.0) with 483328K/40960K bytes of memory.
Processor board ID FGL162722DK
2 Gigabit Ethernet interfaces
DRAM configuration is 64 bits wide with parity enabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
Press RETURN to get started!
*Mar 1 00:00:04.931: %IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL: Module name = c2900 Next reboot level = ipbasek9 and License = ipbasek9
*Mar 1 00:00:05.019: %IOS_LICENSE_IMAGE_APPLICATION-6-LICENSE_LEVEL: Module name = c2900 Next reboot level = uck9 and License = uck9
*Jan 23 07:37:07.403: %IFMGR-7-NO_IFINDEX_FILE: Unable to open nvram:/ifIndex-table No such file or directory
*Jan 23 07:37:15.119: %MAINBOARD-1-UNKNOWN_WIC: wic card in location 0/0 has an unknown id 0x6EF
*Jan 23 07:37:18.679: %LINEPROTO-5-UPDOWN: Line protocol on Interface VoIP-Null0, changed state to up
*Jan 23 07:37:18.679: %LINK-5-CHANGED: Interface GigabitEthernet0/0, changed state to reset
*Jan 23 07:37:18.679: %LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to reset
*Jan 23 07:37:19.887: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/0, changed state to down
*Jan 23 07:37:19.887: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0/1, changed state to down
*Jan 23 07:37:20.823: %LINK-3-UPDOWN: Interface GigabitEthernet0/0, changed state to down
*Jan 23 07:37:20.823: %LINK-3-UPDOWN: Interface GigabitEthernet0/1, changed state to down
*Jan 23 07:37:21.063: %SYS-5-CONFIG_I: Configured from memory by console
*Jan 23 07:37:23.083: %LINK-5-CHANGED: Interface GigabitEthernet0/1, changed state to administratively down
*Jan 23 07:37:23.755: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.1(1)T, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2010 by Cisco Systems, Inc.
Compiled Mon 22-Mar-10 02:13 by prod_rel_team
*Jan 23 07:37:23.759: %SNMP-5-COLDSTART: SNMP agent on host Hewitt_Noida is undergoing a cold start
*Jan 23 07:37:37.483: %DSPRM-5-UPDOWN: DSP 1 in slot 0, changed state to up
*Jan 23 07:37:37.483: %DSPRM-5-UPDOWN: DSP 3 in slot 0, changed state to up
*Jan 23 07:37:37.483: %DSPRM-5-UPDOWN: DSP 2 in slot 0, changed state to up
Hewitt_Noida>
Hewitt_Noida>
Hewitt_Noida>
Hewitt_Noida>en
Hewitt_Noida#
Hewitt_Noida#
Hewitt_Noida#sh diag
Slot 0:
C2901 Mother board 2GE, integrated VPN and 4W Port adapter, 2 ports
Port adapter is analyzed
Port adapter insertion time 00:00:56 ago
EEPROM contents at hardware discovery:
PCB Serial Number : FOC1624697D
Hardware Revision : 1.0
Part Number : 73-11834-08
Top Assy. Part Number : 800-30795-06
Board Revision : A0
Deviation Number : 123694
Fab Version : 03
Product (FRU) Number : CISCO2901/K9
Version Identifier : V06
CLEI Code : CMMJA00ARA
Processor type : C1
Chassis Serial Number : FGL162722DK
Chassis MAC Address : d48c.b51a.b668
MAC Address block size : 72
Manufacturing Test Data : 00 00 00 00 00 00 00 00
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF C1 8B 46 4F 43 31 36 32 34 36 39 37 44 40
0x10: 06 17 41 01 00 82 49 2E 3A 08 C0 46 03 20 00 78
0x20: 4B 06 42 41 30 88 00 01 E3 2E 02 03 CB 8C 43 49
0x30: 53 43 4F 32 39 30 31 2F 4B 39 89 56 30 36 20 D9
0x40: 04 40 C1 CB C2 C6 8A 43 4D 4D 4A 41 30 30 41 52
0x50: 41 09 C1 C2 8B 46 47 4C 31 36 32 37 32 32 44 4B
0x60: C3 06 D4 8C B5 1A B6 68 43 00 48 C4 08 00 00 00
0x70: 00 00 00 00 00 F3 00 65 40 01 25 41 00 87 42 00
0x80: 00 F8 00 28 03 E8 1C 89 07 D0 20 21 0B B8 20 93
0x90: 0F A0 21 2F 13 88 21 83 17 70 21 A8 1B 58 21 B0
0xA0: 1F 40 21 AB 23 28 21 79 27 10 21 78 41 01 1D 42
0xB0: 00 00 F8 00 28 03 E8 1C 20 07 D0 1F 40 0B B8 20
0xC0: 6C 0F A0 21 34 13 88 21 34 17 70 21 98 1B 58 21
0xD0: 98 1F 40 21 98 23 28 21 34 27 10 21 34 FF FF FF
0xE0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0xF0: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
PVDM Slot 0:
128-channel (G.711) Voice/Fax PVDM3 DSP DIMM PVDM daughter card
Hardware Revision : 1.0
Part Number : 73-11810-03
Board Revision : C0
Deviation Number : 0
Fab Version : 03
PCB Serial Number : FOC1602145Q
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 00
Product (FRU) Number : PVDM3-128
Version Identifier : V01
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 05 DC 41 01 00 82 49 2E 22 03 42 43 30
0x10: 88 00 00 00 00 02 03 C1 8B 46 4F 43 31 36 30 32
0x20: 31 34 35 51 03 00 81 00 00 00 00 04 00 09 00 CB
0x30: 8F 50 56 44 4D 33 2D 31 32 38 20 20 20 20 20 20
0x40: 89 56 30 31 20 D9 02 40 C1 FF FF FF FF FF FF FF
0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
WIC Slot 0:
Unknown WAN daughter card
WIC module not supported/disabled in this slot
Hardware Revision : 1.0
Top Assy. Part Number : 800-34658-01
Part Number : 73-13420-01
Board Revision : B0
Deviation Number : 124402
Fab Version : 05
PCB Serial Number : FOC16100L9C
Version Identifier : V01
Product (FRU) Number : VWIC3-2MFT-T1/E1
CLEI Code : COUIA7NCAA
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 06 EF 41 01 00 C0 46 03 20 00 87 62 01
0x10: 82 49 34 6C 01 42 42 30 88 00 01 E5 F2 02 05 C1
0x20: 8B 46 4F 43 31 36 31 30 30 4C 39 43 89 56 30 31
0x30: 20 CB 90 56 57 49 43 33 2D 32 4D 46 54 2D 54 31
0x40: 2F 45 31 C6 8A 43 4F 55 49 41 37 4E 43 41 41 03
0x50: 00 81 00 00 00 00 04 00 D9 03 40 C1 CB FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Hewitt_Noida#Hi Akshay,
As per
http://www.cisco.com/en/US/partner/prod/collateral/routers/ps5855/data_sheet_c36-609138.html
VWIC3-1MFT-T1/E1 is supported since 15.1(1)T1 and later.
Make sure you have this minimum IOS.
HTH
Manish -
"........iMac is not supported on the iPhone
I have an older iphone - 2 I think. When I try to connect the bluetooth I receive a message on the iphone, ".........iMac is not supported on the iPhone" Does anyone have a solution. Both the iphone and imac can find each other, the iphone just will not accept the imac. Is there a download to upgrade the iphone to accept my new imac. Thank you.
iPhone's have never been able to sync via Bluetooth.
In the last year Apple added WiFi sync to iTunes, so you can sync an iPhone or iPad via WiFi with iTunes.
You can also sync wirelessly over the internet using iCloud for contacts, calendars, bookmarks etc - again over WiFi.
But you cannot, and never have been able to, sync an iOS device with a Mac over Bluetooth. -
Dear sir,
Nice to meet you.
When I running the PXIe-4141 Calibration Function "niDCPower Cal Adjust Voltage Leve.vi" in niDCpower version 1.8,
it will show an error "calibration function is not supported by the device."(false cae)
But if I run the PXIe-4141 Calibration Function "niDCPower Cal Adjust Voltage Measurement.vi", (true case)
it will work.
See the attachments.
My Equiptment list:
WinXP SP3
Labview 2011
niDMM 3.0.5
niDCpower 1.8
PXI-1073 case with 2 cards.
slot2: PXIe-4141
slot6: PXI-4071
Could someone tell me the solution?
Solved!
Go to Solution.
Attachments:
4141-cal adjust voltage level.JPG 203 KB
4141 manual cal_20130722.vi 46 KBUpdate:
Error Code: xBFFA4A42
niDCPower Cal Adjust Voltage Level.vi<ERR>Requested calibration function is not supported by the device.
Status Code: -200445
See "voltagle level error.JPG"
And the same error for "niDCPower Cal Adjust Current Limit.vi".
See "current limit error.JPG"
Attachments:
voltagle level error.JPG 15 KB
current limit error.JPG 16 KB -
When I try to open the EOS digital solution disk ver 24.1 for my new Canon Rebel T3i camera on my Mac 10.5.8 a notice "this software is not supported by the CPU you are using" comes up. Do I need this software? Can I just download the pictures to my Mac without using the Canon software?
When I try to open the EOS digital solution disk ver 24.1 for my new Canon Rebel T3i camera on my Mac 10.5.8 a notice "this software is not supported by the CPU you are using" comes up
You need to contact Canon - or read the software specs - it sounds like the software you got form them is not supported by your computer
Do I need this software?
Probably not - exactly what about it do you want?
Can I just download the pictures to my Mac without using the Canon software?
Probably - if you are shooting JPEG - launch iPhoto and in the iPhoto preferences set action when a camera is connected to launch iPhoto and connect your camera - iPhoto should launch and you should be able to import
Some cameras need to be set to mass storage mode - read your camera manual for details and procedures
If you are using RAW then your camera needs to be on this list and you need the versions of software noted - http://support.apple.com/kb/HT4757 - for older OS versions you can use google to find the list of supported cameras
LN -
I want to edit my raw images on cs5 photoshop. But when I go to open the .CR2 file it says
'' Could not complete your request because the file appears to be from a camera model which is not supported by the installed version of Camera Raw. Please visit the Camera Raw help documentation for additional information. ''
When I go to updates in photoshop help i try to update photoshop and photoshop camera raw but it then says
'' Updates could not be applied the error log file may help you in identifying the problem. Then, try updating again. If the problems persist, contact customer support for further assistance.
Photoshop Camera Raw 8.7.1(CS6) There was an error installing this update. Please quit and try again later. Error Code: U44M1I216 ''
I dont know how to get around this please helpCR2 files from which Canon camera?
Supported cameras are listed here
Camera Raw plug-in | Supported cameras -
Error Message: This type of file is not supported, or the required codec is not installed?
I am trying to get media from my computer, and I only receive this error message :
This type of file is not supported, or the required codec is not installed?
What should I do? I have a window 8 laptop. My video files are from my itouch/ipod. I am using Premiere Elements 7.
I have used this software with success before. HELP would greatly be appreciated!darlingdarleen
Did both laptop 1 and 2 have QuickTime (latest version or any version) installed on the computers with Premiere Elements 7 when you got this "this type of file......" message?
If you go to the opened Premiere Elements 7 projects involved and look at Share/Personal Computer/QuickTime, do you find that QuickTime Presets are shown and that you find export settings choices under the Advanced Button/Video Tab and Audio Tab?
Look at the file name of the video. Do you see any irregularies in the name of the file, dots and such?
If you record new iPod footage, open a new Premiere Elements project, and import that iPod footage, do you still get the error message? Putting aside, iTouch, what model iPod are these videos coming from?
Thanks.
ATR -
Error Message: "The formula syntax is not supported by the report"
We are using 'Development Environment: SAP Crystal Reports, version for Visual Studio 2010 u2013 Standard ' and using CrystalDecisions.CrystalReports.Engine and CrystalDecisions.ReportAppServer APIu2019s
I am reading SQLExpressionFields from one source .rpt file & want to add it to another ReportDocument. While doing so, it gives an error " The formula syntax is not supported by the report"
doc.ReportClientDocumentDataDefController.FormulaFieldController.Add(formualField); // formualField is SQLExpressionField from source ReportDocument
But when I tried to Add FormulaField, it succeeds
Please help me in knowing how to add SQlExpressionFields to ReportDocument.
Regards,
-atulThanx Don & Ludek for the reply.
CR provides support for addition/modification of SQLExpressions.
CRAXDRT.Application application = new CRAXDRT.ApplicationClass();
CRAXDRT.Report innerReport = application.OpenReport(path, CROpenReportMethod.crOpenReportByTempCopy);
innerReport .SQLExpressionFields.Add(name, strSQLExpression)
CRAXDRT.dll provides support for addition/modification of SQLExpression fields. But its not compatible with 64bit.
Just curious to know, is there any future plan to provide support for add/modify SQLExpression fields?
Thanx
-atul
Edited by: Atul Chivate on Aug 21, 2011 6:13 PM -
ERROR: Update mode C is not supported by the extraction API - R3 11
Hi gurus,
I just tryed to implement the solution I found at this link:
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/d3219af2-0c01-0010-71ac-dbb4356cf4bf
The data source is based on an Infoset on the KONV R/3 Table.
I setted the AIM delta process and I did all the activities as written in the document.
The process works if I load data to bw in "full", with "Init without data transfer" and "delta" mode. Of course if I change a Purchase document, it will be posted in the delta queue and then loaded to bw with the next delta load.
The "initialize delta process" (with data) doesen't work and returns the following error:
Update mode C is not supported by the extraction API
the error code is R3 11.
have you any idea about it???
Thanks!!!
Regards!
MatteoHi,
for me it sounds quite simple. It is that the update mode 'C' get flagged as 'not allowed' for this extractor. Did you check with rsa3? I guess you will get the same error message. May be you can start debugging in rsa3 to find the place where the update mode gets checked.
Anyway, it shouldn't be a issue as you have a workaround. May be you should raise a error message at sap because of this.
regards
Siggi -
ITunes error message - "video format is not supported by the iPad" My video is mp4, mpeg-4.
When syncing my iPad 2.... Why do I get this iTunes error message? "video format is not supported by the iPad"
My video is mp4, another is mpeg-4.
I thought the iPad 2 could play almost any format.Must conform to these specs:
Video formats supported: H.264 video up to 720p, 30 frames per second, Main Profile level 3.1 with AAC-LC audio up to 160 Kbps, 48kHz, stereo audio in .m4v, .mp4, and .mov file formats; MPEG-4 video, up to 2.5 Mbps, 640 by 480 pixels, 30 frames per second, Simple Profile with AAC-LC audio up to 160 Kbps per channel, 48kHz, stereo audio in .m4v, .mp4, and .mov file formats; Motion JPEG (M-JPEG) up to 35 Mbps, 1280 by 720 pixels, 30 frames per second, audio in ulaw, PCM stereo audio in .avi file format
Or download an alternate video player,such as avplayerhd. -
Error message: this computer is not supported by the system recovery media.
I replaced a bad samasung hard drive in my Pavilion dv6z 3200 with a Seagate Momentus XT 750 GB 7200RPM SATA 6Gb/s 32 MB Cache 2.5 Inch Solid State Hybrid Drive ST750LX003 and when trying to restore Windows 7 64 bit OS get the error message "this computer is not supported by the system recovery media"
Is the new hdd at least as large a capacity as the original? Can be larger capacity, but sometimes smaller will cause error.
Enter BIOS by tapping F10 key. Is all system info intact/complete?
******Clicking the Thumbs-Up button is a way to say -Thanks!.******
**Click Accept as Solution on a Reply that solves your issue to help others**
Maybe you are looking for
-
Hi, I've bought a HTPC based on MSI 785GM-E51. I haven't noticed that this motherboard has only HDMI and 6ch output for sound. I've A/V receiver with no hdmi-in connector. My question is if one of 6ch outputs is coaxial? Sorry for my english - haven'
-
Please help? Why has my iTunes account been disabled?
Just today, when i went on my macbook pro to purchase the new shinedown album, a box popped up that said, "your Apple ID has been disabled". I tried purchasing it many times, but the same message. Also, i trired buying this on my ipod touch and on my
-
Open items sorting without +/- sign
Hi SAP GURU's, i would like to display the open items without +/- sign when i will try to sort. it is possible in edit options in while clearing. but when i will try to display the open items i can not get that option. Please send the solution as ear
-
Hi, The executeThreadCount property in 4.5.1 used to be set with respect to the no of database connections. Now in 5.1 it is set wrt to the no of processors. In the 'Performance tuning your JDBC App" document, it states that the ExecuteThreads => Use
-
Linking a MovieClip button to a URL?
Hello all, I have recently followed a Adobe Flash tutorial, which has helped me make MovieClip buttons which extend to the left when hovered over. This tutorial can be found here: http://www.schoolofflash.com/2008/05/flash-cs3-tutorial-movie-clip-but