Wireless mouse and keyboard not recognized

I know that I have had this issue before, but can't remember what the solution is (old age?) My iMac G5 PPC has a wireless mouse and keyboard (the old apple white one). The iMac came with these as an option but WITHOUT the bluetooth card inside. (I still don't know how this works, but it does). Anyway, the mouse and keyboard were not recognized when I tried to get on today. The batteries are good. If I go to system prefs (using an even older wired mouse) there is no bluetooth option (since no card is present). I don't know how to get the computer to try to recognize both. Any help is definitely appreciated.

HI David,
If the iMac didn't come with Bluetooth software/hardware, then are you using a USB Bluetooth dongle?
And open System Profile (Applications/Utilities)
Select Bluetooth on the left under Hardware. You may need to click the gray disclosure triangle so it faces down. What does it say on the right?
If the Bluetooth icon is in your Status Menu Bar (top right in your screen). Click the icon and make sure Bluetooth is turned on. Then click: Open Bluetooth Preferences and try re-pairing the mouse and keyboard.
Carolyn

Similar Messages

  • Not responsive wireless mouse and keyboard, No internet/wifi and Bluetooth connection.

    Hi,
    I need help as both my wireless mouse and wireless keyboard are totally no responsive and I replaced them with fresh new batteries. My wifi/internet connection is offline too. My Bluetooth signal is the Bluetooth with jagged lines "Bluetooth offline". I tried to disconnect all my USB devices and restarted. I tried the methods listed here but to no avail.
    Yesterday afternoon there was a lightning in the skies and it caused blackout throughout my whole house. So it might be due to the power surge from the Lightning but all my other devices like my iPhone and modem router are working fine. I restarted the router too. It was fine the whole evening till nighttime yesterday. This morning I woke up, I can't do anything at all.

    First thing to try is resetting the PRAM per the instructions below. If that does not work then please use the instructions on how to connect a Bluetooth mouse and keyboard below.
    iMac SMC and PRAM reset
    Troubleshooting wireless mouse and keyboard issues - Apple Support

  • Wireless Mouse and Keyboard don't work under bootcamp. Any suggestions?

    I installed Windows 7 through Boot Camp. Everything works, but my wireless mouse and keyboard. If I add a wired mouse and keyboard, they work. Have reinstalled Bootcamp a few times, but when I try and add the devices. they are seen, but then can't pair.
    Any help would be appreciated.

    Well, the 'unplugged' reference was noted earlier and I wasn't sure if you'd get a
    better response than a standard suggestion to try the other ideas in this link first
    •Intel-based Macs: Resetting the System Management Controller (SMC) - Apple Support
    before actually performing the SMC, that is a dragnet kind of catch-all, sometimes.
    All of my keyboard & mouse units are USB and I've gone as far as supplying the
    mouse and other peripherals with a powered USB hub; so power from the Mac
    isn't spread too thin. The keyboard is one of the only items that should be attached
    to the USB port; as it has to work on startup pre-boot keyboard shortcuts... Such
    as SafeBoot, PRAM reset, and others where you need a live keyboard and BT
    may not be up to the task of being ready. Three going on four of my Macs have
    bluetooth capabilities for those items; but I can't justify the continual upkeep cost.
    Spare USB keyboards and a few extra mouse are handy as troubleshooting tools, too.
    There are some USB keyboard references among search results in this linked page:
    https://www.google.com/?gws_rd=ssl#q=Apple+USB+keyboard+troubleshooting
    Perhaps the SMC pre-reset suggestions may help resolve the issue, if not, try reset.
    Good luck & happy computing!
    edited

  • Apple wireless mouse and keyboard stop working ... now says OS X version and bluetooth incompatible

    For no apparent reason my apple wireless mouse and keyboard stopped working. I was not upgrading or installing anything, the batteries are good, nothing was changed as far as I know. Now bluetooth discovers the paired devices, connects for about 30 seconds, the disconnects ... or stays connected but doesn't work.
    What's happenned ... I'm rushing to finish a big job ... any ideas? I've tried re-pairing but doesn't work ... says that OSX version may be incompatible with device bluetooth ... I'm using Lion so maybe there is another lion problem?

    Hello:
    Barry: What do you mean with "making devices favorites"?
    This is the method:
    Go to system preferences>bluetooth.  Highlight an item in the sidebar.  If detailed information does not appear, click on the little gear and select show more info.  Then click on the gear again and select favorite.
    And how could an hardware-related problem be (temporarily) solved rebooting the OS?
    Intermittent problems are, IMHO, most often caused by hardware.  Restarting will occasionally "fix" problems - why, I do not know.
    Barry

  • TS3048 how to turn on bluetooth when you only have a wireless mouse and keyboard

    How can you turn on the Bluetooth when you only have a wireless mouse and keyboard?

    Hello:
    Read this (the part about OS X not allowing Bluetooth to be turned off unless a USB mouse is connected):
    http://support.apple.com/kb/TS3048?viewlocale=en_US
    I have an old USB mouse available in case something happens to my BT mouse.
    Barry

  • Wireless Mouse and keyboard have lost connectivity with iMac?

    Computer turned off for a week. Restarted, and wireless mouse and keyboard no longer connected to computer. Help please

    Hello Pompoo220s,
    It is certainly difficult to use the computer if your wireless keyboard and mouse do not connect or stay connected.  I found a few resources I recommend for this issue.
    I recommend reviewing this article first:
    Troubleshooting wireless mouse and keyboard issues
    http://support.apple.com/kb/ts3048
    If the issue persists, I recommend reviewing the section titled "Top troubleshooting tips" in the article below.  Step 9 specifically stands out to me for the issue you described:
    9. Restart your computer
    Sometimes a simple restart of your Mac is all it takes to get things running smoothly again. You may also want to try resetting your computer's PRAM and NVRAM.
    Bluetooth Quick Assist
    http://support.apple.com/kb/ht1153
    Thank you for using Apple Support Communities.
    Best,
    Sheila M.

  • Why do I sometimes suddenly lose Bluetooth from my Imac? I use it for my wireless mouse and keyboard. I then can't find it in system preferences but have to shutdown my Mac and hope it comes back

    This is an infuriating problem and wondered if it happens to other people too and if I am doing the right thing by turning the Mac off then on again.

    Hi there vickivoo,
    You may find the troubleshooting steps in the article below helpful.
    Troubleshooting wireless mouse and keyboard issues
    http://support.apple.com/kb/ts3048
    -Griff W. 

  • My pointer keeps turning into a colorful spinning pinwheel. Mac OS X (10.5.8) using a wireless mouse and keyboard, desktop computer

    My pointer keeps turning into a colorful spinning pinwheel. Mac OS X(10.5.8) using a wireless mouse and keyboard ,desktop computer.

    The spinning wait cursor (or "beachball") generally means there's some problem that's causing the current app to freeze, or slowing down the current application, or that's slowing down the whole system. 
    Here's an overview of the spinning wait cursor.
    Make a backup first, using the Disk Utility tool booted from your installation DVD to external storage.  This backup to ensure you still have access to your most current and complete data, shut this be a problem with your hardware.
    Then use Utilities > Activity Monitor.app and the Utilities > Console.app tools to see what's going on, and whether there are related errors being logged. 
    There are some general troubleshooting articles around, too.

  • Apple Wireless mouse and keyboard with Windows on iMac Intel

    Hi there!
    Is it possible to use the Apple Wireless mouse and keyboard on the iMac Intel running Windows XP?
    My bluetooth setup assistant can't find any of them.
    Thanks!

    Actually if You Use the wireless mouse during the setup for windows it works fine the only drawback it that using the wireless mouse on windows is that it drains the battery more quickly than Mac OS X does. So make sure you have extra batteries around

  • My MacBook keyboard and track pad stopped functioning after pairing an Apple wireless mouse and keyboard. Any suggestions?

    My MacBook keyboard and track pad stopped functioning after pairing an Apple wireless mouse and keyboard. Any suggestions?

    I deleted the mouse by selecting it in the bluetooth options and clicking the minus tab. I went ahead and reinstalled OS X right afterwards. Right now I am having to use a USB mouse and keyboard. I disconnected both prior to start up. I get a widow that shows a demonstration on how to install batteries into a wireless mouse only way to pass that screen was to reattach the USB mouse. Then with a fresh startup no resolve.

  • Wireless Mouse and Keyboard Install Problem

    I am trying to install my wireless keyboard and mouse onto my Mac OS X 10.3.9. My dad had this computer before me and had the mouse and keyboard paired and working. After it was shipped to me, I attempted to pair these again with no luck. THe bluetooth won't recognize either and if i try and run the KeyboardandMouse.pkg as instructed, the icon simply isn't there when I insert the disk. I've attempted to pair using the system preferences, but it cannot locate either the keyboard and mouse. Yes, I do have new batteries installed and the lights do blink when switched on. Any help is appreciated. Thanks.

    Hello again:
    Try trashing the BT preference file (com.apple.bluetooth.plist) and restarting.
    If that does not work (although it will take you a bit of time), I think I would try an archive and install:
    http://docs.info.apple.com/article.html?artnum=107120
    Barry

  • Wireless mouse and Keyboard Issue after closing the lid - external display

    Can anyone give any insight. Recent purchase of a new Late 2008 15" MBP. I have connected it to an external 24" Apple monitor on my desk and use a wireless mouse and wireless keyboard on my desk top. I have configured the laptop to wake on bluetooth devices. So here is the problem: The laptop when the lid is up recognizes the bluetooth keyboard and mouse. I close the lid/screen. Laptop powers down... the after several seconds I move the mouse and the laptop comes alive... But after that there are no bluetooth devices attached. When I use the mouse, I get "connection lost" with a white figure of the mighty mouse on the screen. The wireless keyboard is not there and I have to open the lid and manually find the mouse and reconnect. The keyboard seems to work however....
    Apple..... any thoughts..... anyone?????

    Hi Stentdoc; I'm thinking, 'connection lost ~= sorta low AA batteries in the Mighty Mouse? (I would put in fresh AA batteries in the mouse and keyboard, to eliminate as an issue that the 'connection lost' is due to low batt voltage; that this is causing the failure to wake.) ... then, in System Preferences > Hardware > Energy Saver, settings for Power Adapter > Sleep, set to "never" for "Put the computer to sleep when it is inactive for ..." to eliminate that as a conflict when trying to wake with bluetooth from sleep induced by closing the lid ...
    Check your current "Sleep" setup (I left my MBP as "3")
    go to Utilities > Terminal
    After you launch Terminal, the first step is to determine which sleep mode your Mac is currently using. You can both view and change the sleep mode using the Unix program pmset. To see your current settings, type (or, copy and paste)
    pmset -g | grep hibernatemode
    press 'enter'
    You should see something like this:
    $ pmset -g | grep hibernatemode
    hibernatemode 3
    So your machine is using mode 3 ... thanks to the documentation for the handy Deep Sleep Dashboard widget, which puts your machine immediately into hibernation mode (so you don’t have to yank all the power sources to invoke it):
    * 0 - Old style sleep mode, with RAM powered on while sleeping, safe sleep disabled, and super-fast wake.
    * 1 - Hibernation mode, with RAM contents written to disk, system totally shut down while “sleeping,” and slower wake up, due to reading the contents of RAM off the hard drive.
    * 3 - The default mode on machines introduced since about fall 2005. RAM is powered on while sleeping, but RAM contents are also written to disk before sleeping. In the event of total power loss, the system enters hibernation mode automatically.
    also, I enabled this (to change back, input "lidwake 1":
    go to Utilities > Terminal
    type in sudo pmset lidwake 0 then "enter"
    it will ask for your password. type it in, that's it!
    Now, when your computer is sleeping with the lid closed, when you open the lid nothing happens until you press any key ... nice: keeps it off when accidentally opened, like in a backpack?
    WARNING: Improper use of the sudo command could lead to data loss
    or the deletion of important system files. Please double-check your
    typing when using sudo. Type "man sudo" for more information.
    To proceed, enter your password, or type Ctrl-C to abort.

  • UN-pairing wireless mouse and keyboard ?

    I have a new(ish) 27" iMac, OS X 10.6.3 [ with two-tone display ...but that's another story ]
    I set it up with the wireless mouse and wireless keyboard that came with it.
    The instructions were pretty clear how to "pair" the mouse and keyboard.
    So I paired them both up and got started with my new iMac.
    But I really didn't like either one (to each his own).
    Tried my best but just never warmed up to them.
    So, I have just gotten me new, third party, wired mouse and wired keyboard.
    Question: am I supposed to formally UN-pair the mouse and keyboard?
    Seems like you ought to.
    Tell the iMac to quit looking for them?
    There's an on/off switch on the mouse.
    I can just turn it off.
    But do I UN-pair it first.
    Or anything?
    And...there's what the manual says is an on/off switch on the keyboard.
    But it seems to be an "on/on" switch.
    Maybe this is a "small deal".
    Or maybe it is a "no deal at all".
    But I find that some times it DOES make a difference whether you do something just the right way or not.
    So, just trying to find out.
    Thanks,
    James

    David,
    I have also invoked the wrath of someone that I was assisting with an issue who accused me "assuming" that they were a beginner and of talking down to them. It is often a thankless position.
    I was mainly poking fun at myself for being so basic in my understanding of some of this stuff.
    But I understand exactly what you're saying.
    Hard to know isn't it?
    I believe that if you highlight each device separately in the list, that you can then select the - symbol next to the cogwheel and delete the device altogether from your iMac.
    Well, I WAS highlighting each device separately, but all the "cogwheel" was giving me was the "disconnect" option.
    Then I wondered, hmmm... what's these little "+" and "-" symbols next to the cogwheel mean?
    BAM! yep, the minus sign removes them from the computer completely.
    ..which, if I'm not going to be using them again was what seemed TO ME the thing to do.
    Thanks for your help!
    James
    P.S. And I just now noticed, someone deemed my passing comment in my OP about my display to be politically incorrect. Didn't realize it would have been a big deal. Oh well, live and learn.

  • Problems with bluetooth connection to wireless mouse and keyboard

    I am using a mac book (aluminium) with 10.6.4 with a Cinema Display and a wireless keyboard and mouse. My time capsule is located only 1 meter away from the mac book and every time the automatic sync starts my mouse and keyboard do not repsond anymore. It seems that the bluetooth connection is somehow heavily loaded due to the network traffic. I have updated all devices and restarted the computer several times. It always keeps on doing that. Any help?

    philip_axmann wrote:
    every time the automatic sync starts my mouse and keyboard do not repsond anymore.
    what you are seeing is called _*wireless interference*_.
    change the channel your TC broadcasts on.
    JGG
    edited by the Jolly Green Giant (where Green stands for environmentally friendly)

  • New wireless mouse and keyboard issues

    I have a new 20", 2.4GHz alu iMac, and I ordered it with the new bluetooth keyboard, and bluetooth mighty mouse. They've always worked great, but yesterday, the mouse has had intermittant lag, and it says that the keyboard has lost connection. I've been running Leopard since it came out, and I've never had such problems with Tiger. I reinstalled Leopard a few hours ago (erase and install), and I'm still getting the lag. I wanted to see whether it is my mouse, so I tried pairing it with my brother's white intel iMac, and it couldn't pair, but it made my brother's bluetooth mighty mouse lag too! Could this be due to interference? Our rooms are right beside each other.
    Also, when the lag occurs, I get the message that its lost connection with the keyboard, however it still works perfectly. The lag is very noticeable, and it takes about 3-4 times longer for the mouse to move, while being very choppy. This is for about 10-15 seconds, and then it goes normal speed again.
    Is anyone else having this challenge? Could anyone diagnose whether it's likely to be the computer, the mouse, or interference, (or other!)?
    Any feedback is greatly appreciated.

    I have a 6 week old imac 24" alu intel with wireless keyboard & mouse and it was all working fine until the 10.5.1 upgrade. it also started on the same day there was a big rain storm so I thought that might be messing with my blue tooth connections. i have no other bluetooth devices other than the mouse and keyboard. at first it was intolerable. i'd get the keyboard connection lost message every few minutes, the keyboard would continue to function and the mouse would go very sluggish for a minute or 2. this was happening every 5 minutes or so. i deleted each one an reconnected, shut everything off, restarted the computer and it seemed ok for about 1 hour and then it happened again a few times. definitely not as often as before but it still happens from time to time every few hours. power on both is about 75% and seeing as they have new duracel batteries i'm sure they are not dead.
    I did the auto update to 10.5.1 and had all the permission issues so then downloaded and installed the larger 100+ meg update. not sure if this has caused any problems.
    So far leopard has only been a pain. Reason 4 crashes, Parallels 3 crashes, Mail crashes (I wrote some important notes which I guess don't get automatically saved like drafts and lost the notes when mail crashed several hours after I wrote them), my software update even crashed once. is Leopard built on OS 9 technology? what a disappointment.
    Oh and internet and wireless connection to ADSL seems pretty slow, slower than tiger I think.
    Windows should start a new campaign called "Come back".
    One last beef, do other people find this wireless keyword (metal) not so responsive, letters get missed as I type, space bar is stiff and squeaky, overall not great for someone doing a lot of writing? that's what I think.

Maybe you are looking for