Wireless network adapter - yellow exclamation mark triangle

Hello, My wireless internet button is orange and isn't and doesn't change colour when I press it so wifi isn't working. In network adapters, my wireless adapter shows up and is: Ralink RT5390R 802.11bgn Wi-Fi Adapter It has a yellow exclamation mark triangle on it. It says it is enabled, but in device status it says: Windows cannot load the device driver for this hardware. The driver may be corrupted or missing. (code 39){Unable to load device driver}%hs device driver could not be loaded.Error status was 0x%x When I try to update driver software, it says the best driver software is already installed and up to date. Please help me get my wifi back - I have a HP pavilion g6 2210sa, Product number C6S45EA#ABU and running Windows 8. Best wishes and thank you in advance.

I have HP 15-r264dx windows 8.1 64 bit laptop with Realtek wireless adapter RTL8188ee 802.11 bgn. There is an exclamation mark with the wireless signal which is white. Sometimes my wireless cannot connect. My wired LAN is OK. I unchecked the option to make adapters power off to save power I think in power management. I have a 2015 driver for the wireless adapter. HP diagnosis would reset the adapter and everything is fine but still the white exclamation mark. I think a setting is not correct, any ideas what it may be and how do I go to it? I am connected with the wireless lan right now to my Verizon DSL router and it is unsecured.

Similar Messages

My network adapter has exclamation point

I have a problem with our computer, its network adapter has exclamation mark and I tried to fix it from reading forums in the internet, and I saw one, run the cmd as administrator and I have notification that saying there logon failure:user account
restriction.possible reasons are blank password not allowed(I put password already),logon hour restrictions(I reset my time and date and my CMOS working) or a policy restriction has been enforced. But still I went to cmd and type netsh winsock reset and after
I restart our computer and it didnt work..
Please help me.It so rush for me to solve.My network adapter is Realtek RTL8139/810x Family Fast Ethernet NIC,my motherboard EMXIH61LT. I hope you have answers for that..Please help me..Thank you...

More often than not when a device isn't working it is because the driver has become corrupted. Re-installing a fresh copy should help
http://windows.microsoft.com/en-us/windows7/Update-a-driver-for-hardware-that-isnt-working-properly?SignedIn=1
http://captaindbg.com/how-to-update-drivers-on-windows-7/ (works on win 8 too)
Wanikiya and Dyami--Team Zigzag

Exclamation mark triangle next to Gmail account in mail

Since the 10.9.2 update on both my iMac and Macbook, there is a exclamation mark triangle next to my Gmail accounts. When clicking on it it says: that it can't login with password identification, too many simultaneous connections.
How can I solve this issue. Before the update everything workend perfectly.

it's a network issue. click on the triangle.

LAN on SysTray has a Yellow Exclamation Mark

So I read through most of the articles on this forum about this topic with no luck...tried installing latest drivers, registry settings, oh and my favorite reboot (really), but seriously this is an issue dating backing to Vista with no "REAL"
solution..Microsoft get off your butts and fix the issue...even though I have connectivity it says no Internet Access...which is false, because I do. The problem is it affects our internal SharePoint sites...all the computers with out the issue work fine and
all the ones that do fail...so I am looking for a solution to eliminating the random exclamation mark once and for all...we use the same image on thousands of machine and the issue is random...any thoughts or want to share in the frustration??
Chris

Hi,
More information about Yellow Exclamation Mark can be found in this link below:
http://blogs.technet.com/b/networking/archive/2012/12/20/the-network-connection-status-icon.aspx
And the second link explains how system determines the network locaion, if the network profile is incorrectly identified to a public profile, then it might cause problems to access the internal sites such as SharePoint sites.
Network Location Awareness (NLA) and how it relates to Windows Firewall Profiles
http://blogs.technet.com/b/networking/archive/2010/09/08/network-location-awareness-nla-and-how-it-relates-to-windows-firewall-profiles.aspx
Meanhwile, if you have multiple network adapters\profiles in the system, then I suggest remove unused one if possible, test this issue again.
Temporarily turn off firewall and anti-vius software, test this issue.
Yolanda Zhu
TechNet Community Support

I am missing masters in aperture , getting an yellow exclamation mark , but still getting a preview of those pics .how to create a master .i have done rebuilding , repair , but still same?..please help

missing masters in aperture , getting an yellow exclamation mark ,

Q: Is there a way to place an image at 100% without having to do that extra resizing step?
I think here you want your images to fit in the full page size frame automatically. For this you can try the follwoing steps:
1. Create a new doc
2. Goto Object menu and choose Frame fitting options
3. Select Autofit and from Fitting drowdown, select "Fit content to frame". Refer the screenshot below:
After this you images should automatically fit in the entire page placeholder frames. Please let me know if this does not work or if the problem you are facing is different and I did not understand your problem correctly.
Regards,
Pooja

App Catalog ERROR "The action could not be completed. Try again later" Yellow exclamation mark

Hello, I have problem with access to App Catalog, when i try to access to App Catalog it's give error "The action could not be completed. Try again later" with yellow exclamation mark. I tried to make partial erase, I made full erase, I made Secure erase, but all these steps not helps.
I renew my firmware with latest webOSDoctor, but still nothing. Then I changed my Palm Profile, I create new one, but still NOT WORKING!
I checked all connections 3G and Wi-Fi, everything is ok, but App Catalog still not working.
So, I contacted with Palm Support, I told about this issue and I send them Quick Log and Log
with Description to [email protected]
Reference number for chat: Chat session ID number 89786521
Do you have any solution?
Best regards
Rufat Jalilov
Post relates to: Pre 2 p102una (Unlocked NA)

Honestly saying, the problem I had already a week, I tried to solve it on their own, but all my attempts were unsuccessful, I am sure that this problem is not related to what some of my actions, cause I never made any manipulations with phone.
I really appreciate the attention rendered by the support services, I just need that everything works fine.
I am sure that this is some sort of a strange problems, I have long been searching for an answer in the Internet came on similar way problems have other users.
I received today a update notice for App Catalog, I saw that HP Palm updated App Catalog, I updated my App Catalog, check again, but still nothing changed, same problem "The action could not be completed. Try again later" with yellow exclamation mark.
So, I will wait for a few days, will see what's happening.
Best regards
Rufat Jalilov

Atheros AR5007EG Wireless Network Adapter - With any driver: "The device instance name is invalid"

Hello there,
I was trying to install various "Atheros AR5007EG Wireless Network Adapter" drivers, with versions ranging from 2007 to 2010, both from the manufacturer and specifically for this computer (a Fujitsu Siemens Esprimo Mobile) and others from here:
http://www.atheros.cz/atheros-wireless-download.php?chipset=22&system=3
All of them are for Windows Vista 32bit.
The computer had previous drivers installed and working, but also had a network problem. In the process of figuring out what was causing it, I tried to install newer drivers to see if that was the problem. It turns out the network problem was due to a different
thing that is now fixed (some dependencies of the WLAN Configuration service were turned off), but I'm still stuck installing the new drivers.
TL;DR:
However, every time I install new drivers, after install, Windows says that
"The device instance name is invalid", regardless of what drivers I install. I even tried to install drivers for different hardware in that slot just to see what it told me and IT STILL gave me the same error. I also tried to uninstall the
current driver, checking the box to delete the driver's software, running CCleaner and then deleting
"athr.sys" from the Windows/Drivers folder and
"oem8.inf" from Windows/Inf as those files were referenced in the driver's properties. The install still gives me the same error.
The fact that it gives me this error with any driver leads me to believe it's Windows' fault and not the driver's.
Note: I am translating from the original in Portuguese. "The device instance name is invalid" is the closest/correct translation and seems about right with the info I find online regarding the english version of Vista and how it refers to devices.
This (https://groups.google.com/forum/#!topic/microsoft.public.development.device.drivers/yFa_XnlcLJQ) and this (http://finderr.net/windows/pt-PT/O-nome-da-inst%C3%A2ncia-do-dispositivo-%C3%A9-inv%C3%A1lido-/2082573452) also seems to confirm that, though it
doesn't help me. It may be that the text is actually different in english Vista but I also searched for driver instead of device or stuff like "The device instance name appears to be invalid" and can't find anything either.
I also did SFC /SCANNOW a while ago and it found no errors. I then repeated it again after this problem and this time, SFC found errors BUT it couldn't repair all of them. Here is the CBS log:
https://www.dropbox.com/s/bayum2rsezxpmre/CBS.log
Thank you for the help!
EDIT: The Notebook model is a Fujitsu-Siemens ESPRIMO Mobile V5535 and their support drivers can be found here (after specifying the OS and model):
http://support.ts.fujitsu.com/download/ShowFiles.asp
EDIT2:
The last SFC /scannow scan repaired everything left to repair. The system restore option can't be used because the earliest one still has the (suposedly faulty) drivers installed.
This computer has a Win Vista serial number, but no CD and the second partition doesn't have any kind of backup. The second partition is empty though. So, as a last resort, if I really don't have a choice, I'll try to do an upgrade install to see if that fixes
it and if that still doesn't fix it I'll have to move everything in the users folder to the second partition and format the first which is a bummer :/
EDIT: Here is the setup.api.log that was inside C:\Windows\Inf and details the instalation process of all the drivers:
https://www.dropbox.com/s/tyxs1e4r7rxofch/setupapi.dev.log
I'm still trying to read into that setup.api.log file.

So, can I assume that the only way to fix this error is to download an iso of Windows Vista, unninstall my service packs, upgrade install Vista, run Vistalizator to change the language to Portuguese and then install Service Pack 1 & 2?
EDIT: Alright, so I formatted the thing since the driver bug wouldn't give me a break. The details on that can be found searching for the same thread title either on tomshardware or vistaforums if anyone happens to find this looking for the same error.
I have a real knack for bumping heads with errors that nobody else gets that somehow turn into unfixable bugs. At least if someone else searches for this problem they'll know what to do.

Clients losing Connections yellow exclamation mark still associated

We are having intermittent issue where clients just lose connectivity, they stay associated to the access point but get a yellow exclamation mark.
I have followed the steps in these post but still the issue persists. https://supportforums.cisco.com/thread/2194495
https://supportforums.cisco.com/thread/2002533
WPA2 802.1 x authentication.
We were getting this error before I made the changes
(Cisco Controller) >*dot1xMsgTask: Jan 31 11:58:25.140: 08:11:96:80:33:e0 Key exchange done, data packets from mobile 08:11:96:80:33:e0 should be forwarded shortly
*dot1xMsgTask: Jan 31 11:58:25.140: 08:11:96:80:33:e0 Sending EAPOL-Key Message to mobile 08:11:96:80:33:e0
state PTKINITDONE (message 5 - group), replay counter 00.00.00.00.00.00.00.02
*dot1xMsgTask: Jan 31 11:58:25.141: 08:11:96:80:33:e0 Updated broadcast key sent to mobile 08:11:96:80:33:E0
*Dot1x_NW_MsgTask_0: Jan 31 11:58:25.145: 08:11:96:80:33:e0 Received EAPOL-Key from mobile 08:11:96:80:33:e0
*Dot1x_NW_MsgTask_0: Jan 31 11:58:25.145: 08:11:96:80:33:e0 Ignoring invalid EAPOL version (1) in EAPOL-key message from mobile 08:11:96:80:33:e0
*Dot1x_NW_MsgTask_0: Jan 31 11:58:25.145: 08:11:96:80:33:e0 Received EAPOL-key in REKEYNEGOTIATING state (message 6) from mobile 08:11:96:80:33:e0
After I made the changes there are no errors in the debug just clients stops working with yellow exclamation mark, cannot reach default gateway.
We also recently enabled Rogue policies auto contain rogue on wire and Using our SSID.
WLC4402 7.0.235.0
We want to upgrade the WLC software but want to make sure it’s the issue.

Okay... well at least its not the WLC code or AP tht is an issue. RLDP whould only be used on monitor mode access points, When used with access points that serve clients, the AP when detecting a rogue, will drop all associated clients. The AP's will do rogue detection anyways, so no need enable RLDP.
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_white_paper09186a0080722d8c.shtml
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered"

Yellow exclamation mark in references: What does it mean

In my c# project, i have references to c++/cli and native c++ projects under "references". (i need to have them there, in order to be able to use msbuild on my solution from the command line.). all of these projects have yellow exclamation marks overlayed
to the "reference" symbol. (vs 2010). i can't find any explanation what these symbols are supposed to tell me.
any ideas ?
WM_THX
-thomas woelfer
http://www.die.de/blog

Hi Thomas,
I think this behavior is a warning to user that the native dll referenced by C# project is not supported there.
And I cannot say if it is by design or just a bug, would you mind sharing the connect link here, so that others could see and vote on it?
In addition, for msbuild issue, you may try MSbuild forum for better suggestions/workaround.
Thanks for understanding.
Figo Fei
MSDN Subscriber Support
in Forum
If you have any feedback on our support, please contact
[email protected]
Please remember to mark the replies as answers if they help and unmark them if they provide no help.

Yellow exclamation mark

Yesterday when opening pictures in Camera raw a yellow exclamation mark started appearing on the upper right corner. This doesn't let me use Adjustment brush as the yellow exclamation mark appears every time I pick the brush and start using it on the picture. It's been like that for two days now. Any ideas?

I did try doing the ‘Purge Cache' now, but it's still the same.
With Ctrl +K you get the normal cache for preview and thumbs and that is not the same as the Camera Raw Cache.
Under the menu Bridge you will find just above the bridge Preferences the Camera Raw Preferences (at least, on a Mac) and in this window you find the option to clear the Camera Raw Cache, did you try that one?

IMovie Yellow Exclamation Mark - What's missing?

I have movies that I updated from iMovie 09. When loading the Project, in the Timeline, I see the title in the middle with a yellow exclamation mark. I'm not sure why this is there. I initially had music missing with red and some files missing for some Projects, but I fixed everything. It still shows the yellow exclamation mark. When I hover over it, nothing happens. I have an image of what it looks like. What am I missing from the Project?

Hi,
@Edwin
thanks for pointing me in the right direction Edwin. The problem was that I changed the name of the method after the def-file for the method has been created the first time. JDEV did not update the contents of this file (and/or the DataBindings.cpx). So the method name was wrong and I got errors running my test app.
I removed the task flow completely and set up a new one which is working as expected.
@Juan
for me it looked like I couldn't call the method defined as default action. I got errors (which I didn't read carefully) stating the the method was missing (something like ...#[bindings....} not found). My conclusion was that the exclamation mark in the diagram stating that bindings is unknown was the cause.
The real cause of the problem I described above.
Thanks
Timo

New Intel WIFI Wireless Network Adapter does not recognize Wireless Router

I have had a Linksys BEFW11S4 Version 4 Wireless router for quite some time. It works like a champ and I have one Laptop wired to it and a second using Wireless working just fine. Recently, I received a new ThinkPad W500 Laptop with an Intel WIFI Link 5100 AGN wireless network adapter. The older laptop that works just fine with the router uses a
11a/b/g Wireless LAN Mini PCI Express Adapter by Atheros. However, the NEW laptop with the Intel Adapter fails to connect to the Router. It will either indicate a failure while "Waiting for Association" or it will indicate a failure when waiting to "renew IP Address". Sometimes, it will show a signal strength close to ZERO (Even as the older laptop with the other adapter is showing a signal strength close to 100%) When I called Linksys support, I was told that the facts that the Router (a) works find with the wired Laptop and (b) works fine with the 11a/b/g NEtwork Adapter and (c) works fine when WIRED to the new laptop all indicate that the problem is NOT with the router at all -- but with the Network Adapter. Can anyone tell me what has to be adjusted in the Adapter settings? Right now, I am using IBM Access Connections for BOTH of the wireless laptops. I have made sure to set IDENTICAL values for SSID and WEP (128-bit) [static] password. I have also ensured that all OTHER settings are the same for the two laptops. Yet, in one laptop, there is NO PROBLEM while in the other, I can not get the Wireless Adapter to "see" the signal from the Router. TO further check this, I have [temporarily] disabled the WEP password, enabled SSID broadcast, and disabled the MAC address restrictions that I put in (so that the system would be totally "open") yet the Intel Adapter STILL did not "find" anything. In addition, when I use the "Find WIFI" feature in Access Connections, I find that SOMETIMES the network with SSID is found and sometimes, it will display "unknown network" and not pick up the SSID.
This is all very frustrating. If anyone has experience with the Intel WIFI Link 5100 AGN Adapter, I would appreciate any hints, tricks, ideas, etc.
Think you!!!!
--Zvi

I installed the LATEST version of IBM Access Connections as well as verifying that I have teh LATEST drivers for the Intel Wireless NEtwork Adapter.
What now happens is that I am able to authenticate to the Router. However, I get a failure on "renewing IP Address" -- which [according to the diagnostic message] means that the Rotuer fails to provide me with an IP address to use. Do you have any suggestions?

Ibook suddenly marks photos with yellow exclamation mark

Hi,
I have created several photo albums and had them published. I have always chosen my photos carefully to avoid the yellow exclamation mark. One of my projects was started several months ago and left untouched for a long time. When I went back to the project more than 50% of the photos were now marked with exclamation marks. Then I looked at books that I have finished and had published, and they too have exclamation marks on some photos. I went to a local Apple Store and the "geniuses" were stumped. Any ideas on what may have caused this spontaneous mutation...and how I can fix it?
Thanks
PS Changing the size of the book project does not seem to make a difference

Hi Maliha,
I followed your instruction to execute the exe file under C:\Drivers. After that, I rebooted the system and no more error pop up for the missing audio device. I checked the Device Manager and the Audio Device on High Definition Audion Bus disappeared and the SoundMax was shown. But again, still no sound. I clicked on TroubleShooting on that SoundMax and followed that instruction. I found out the default Sound device was erroneously pointed to BlueTooth. I made the change to SoundMax and voila ... the sweet ding sound came back.
That was a wonderful feeling to be able to fix this nagging problem that my company HelpDesk could not help me. All thank to this forum and particular Maliha. Again, my appreciation to the valuable help.

ITunesHelper Login Item - Yellow Exclamation Mark

Hey people!
I was checking my login items and saw that next to the iTunesHelper there was a yellow exclamation mark... It said that "this item could not be found"... I upgraded my OS to Mountain Lion and it is a bit slow.. You think this could be a contributing factor?

It's old. Remove it.
If you go into you iTunes settings, the checkbox to have it open iTunes when you attach a phone or ipad is what causes it to be placed in the login items.
Not likely.

Yellow exclamation mark--what does it mean?

Hello Aperture experts: I've just started using Aperture and am designing a book. Certain images I've chosen are posted on the layout page with a yellow exclamation mark in the corner. I get it that Aperture is trying to warn me about something, but what? Does anyone know? Thanks.

What are the pixel dimensions of the photo and what is the size you are printing it?
Depending on your personal quality expectations you may find that if you are close you will be ok - i often print photos with the warning knowing that it is my risk
Basically you should have at least 180 dpi to avoid a warning - so a full page 8.5 x 11 print requires a photos of 1530 x 1980 or larger - and remember that if you zoom the photo that reduces the dpi
LN

Wireless network adapter - yellow exclamation mark triangle

Similar Messages

Maybe you are looking for