Wireless Network for Home use.

Hey,
I am new to Mac and have a question about the frequency of the Wireless Network.
I have heard that there will be a new Ghz rate in the near future, 5.0 GHz (n) in stead of the existing standard of 2.4 GHz (g).
Has anyone heard of the new Ghz standard ?
My existing phone system is running at 2.4 GHz and the exiting wireless networks run at 2.4 GHz.
Will there be interference if both are used at the same time ?
I guess that is two questions but the same subject.
Thanks,

My existing phone system is running at 2.4 GHz and
the exiting wireless networks run at 2.4 GHz.
Will there be interference if both are used at the
same time ?
This is a difficult question to answer. It depends on the phone you use. For example, I have a pair of 2.4GHz cordless phones I bought a few years ago that do not interfere with my wireless network as far as I can tell. But many other 2.4GHz phone brands and models do. I only got lucky. There does not seem to be an easy way to tell which phone chipsets will interfere and which will not, even though all of them operate within the "same" frequency range.
2.4GHz is a band that is unlicensed, so anything can happen when you have so many manufacturers putting out phones, networking gear, gaming devices, microwave ovens, and other consumer devices all operating in the 2.4GHz unlicensed band. Sometimes devices just clobber each other.
There is a newer cordless phone standard operating at 5.8GHz. These phones have been in the stores for a while. They cost a little more, but the price has come down a lot in the past year. They are supposed to be unlikely to interfere with a 2.4GHz wireless network. But if you live within range of other homes and offices, you might still have to put up with interference from whatever devices your neighbors use.

Similar Messages

  • Cisco Model 870 router for home office connected to WRT160NL wireless router for personal use

    I am using a Cisco Model 870 router for home office. I just bought a WRT160NL wireless router for home use. I setup the personal wireless router off the personal port of the 870 and can connect with my PC but not with my MAC machines. It can see the Network but when it asks me for passwords, it says they are wrong, which after several attempts I know they are correct.
    The new router is setup as WPA2 personal. Can you advise?
    Cisco Account Manager- Services

    I think I answered my own question. I tried downloading something on my desktop and checked my cellular usage afterwards didn't go up so it's using my home internet and not my data plan.

  • Can I use my wireless/Airport card to create a network for Home Sharing?

    I don't have a separate router. Can I use my MBP's wireless/Airport card to create a network for Home Sharing?

    I was unable to use the network preference "Create Network" option as it kept crashing, so I didn't really get to figure out if this is possible. If anyone else has done this, I would be interested to know for the future.
    Is it possible to setup a home network without a separate router? Is the wireless/airort card enough to setup and maintain a home network for Home sharing?

  • I have a wireless network at home. I run my iphone and ipad on it with no problems. Just purchased a MacBook Pro, and now my wi-fi keeps disconnecting and i get an error message saying another device is using the same IP address. What does all this mean?

    I have a wireless network at home. I run my iphone and ipad on it with no problems. Just purchased a MacBook Pro, and now my wi-fi keeps disconnecting and i get an error message saying another device is using the same IP address. What does all this mean?

    Hello AKCamus
    To give you some ideas of what to do next, I have provided a few articles that will give some troubleshooting Wi-Fi connections and recommended Wi-Fi settings.
    iOS and OS X: Recommended settings for Wi-Fi routers and access points
    http://support.apple.com/kb/HT4199
    iOS: Troubleshooting Wi-Fi networks and connections
    http://support.apple.com/kb/ts1398
    Troubleshooting Wi-Fi issues in OS X Lion and Mac OS X v10.6
    http://support.apple.com/kb/HT4628
    Thanks for using Apple Support Communities.
    Regards,
    -Norm G.

  • I can get on the internet with my laptop using my wireless network at home but I can not get on the internet using my ipad.  The wi-fi setting show a connection on my ipad but I can not pull up the internet.  Any ideas?

    My laptop connects to the internet via my wireless network at home.  My ipad will not bring up the internet using the same connection.  It shows in the wi-fi settings as connected but when I bring up safari, nothing comes up.  Any ideas?

    Look at iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    Additional things to try.
    Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    If none of the above suggestions work, look at this link.
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    Unable to Connect After iOS Update - saw this solution on another post.
    https://discussions.apple.com/thread/4010130?tstart=60
    Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

  • Can Time Capsule be used strictly as a wireless network for ATV and TiVo?

    I apologize in advance for the lengthy narrative but I feel that it will only help in describing my challenge/problem.
    I currently own and have been successfully using an iMac and Apple TV and syncing with my iTunes account. I want to transfer the ATV to my fiancee's house since I'm spending most of my time there. Until we move in officially I'll be keeping my Mac at home. She does not have WiFi and has an old laptop that I'm pretty sure doesn't even support a WiFi radio. We eventually plan on replacing her laptop with a new Mac Book but until that time comes all I want to do is set up a wireless network for the ATV and TiVo service that I also brought over.
    So, I bought the Time Capsule with the future in mind. My question, can I set up TC to act as a wireless router for ATV and TiVo only but hardwire her laptop to keep connected to the Internet? Will I need to connect ATV to her iTunes service through her laptop? Or can I access my information using ATV if the WiFi is set up correctly?
    I know that until I bring my Mac and we eventually replace her laptop, I bought a very expensive wireless router but there is a method to my madness....I think.
    Any suggestions on the hookup process will be greatly appreciated.

    atlas138, Welcome to the discussion area!
    My question, can I set up TC to act as a wireless router for ATV and TiVo only but hardwire her laptop to keep connected to the Internet?
    Certainly.
    Will I need to connect ATV to her iTunes service through her laptop? Or can I access my information using ATV if the WiFi is set up correctly?
    The network would have the same abilities as any other network. I don't know how the AppleTV connects to iTunes but it wouldn't be any different than if the AppleTV were connected to something else.

  • How do I set up a wireless network at home??

    Hi,
    I am new to Mac's. I want to set up a wireless network at home, but I have not got a clue about AirPort, what it is or what it does!?! I am getting a new Mac, but my wife is currently using a Dell Windows laptop and our daughter is using a Windows PC. How do I set up a wireless broadband network at home which works with my Mac and my familys PC's? What do I need to buy and what do I need to do with them? I already have a broadband connection at home. Currently, my wife's PC is connected directly to the broadband modem (via an ethernet cable) that was supplied by the brodband company when I signed up to broadband.
    Thanks for all your help with this.

    scooter has provided links to Apple's pages for the AirPort Express and AirPort Extreme base station (AEBS).
    Both of these devices are IEEE 802.11g wireless routers (also called base stations). If you have an Ethernet connection to the Internet (for example DSL or cable modem), you can connect either of these devices directly to that connection and create a wireless network. Since Ethernet and IEEE 802.11g are worldwide standards you can connect any compatible device (including PCs running Windows).
    Every computer needs a unique IP address. You can think of an IP address as a street address for your house. A unique address guarantees that items addressed to you get to you.
    Typically ISPs provide users with a single (one) public IP address. A public IP address is visible to anyone on the Internet. A router uses the single IP address provided by the ISP and creates multiple local (non-public) IP addresses for you computers. This allows you to use multiple computers.
    If you need to connect both wireless and Ethernet computers you will need the AEBS. The AEBS provides a separate LAN port for Ethernet computers.
    BTW, you can accomplish the same thing with any inexpensive wireless router.
    The advantage of the AEBS over other routers is (a) built-in 56k modem for connecting to a dial-up ISP and (b) USB port for a single compatible printer.
    The advantage of the AirPort Express over other routers is (a) sound output port for streaming music to a stereo and (b) USB port for a single compatible printer.

  • Confused how to set-up a PC & laptop with Cisco WRVS4400N VPN for home use

    Just bought a new PC and laptop and was recommended by (CDW) to use a Cisco WRVS4400N to set up the VPN.
    For home use, only the PC and laptop, both running Windows 7.  I use Comcast as my ISP.
    The mountains of docs confuses me to no end, can anyone simplify this for me.  I look at all the details and do not know where to start.
    In short,
    (1) configure router to recognize my PC and Comcast, and I guess the laptop.
    (2) configure laptop to go wireless and communicate with PC.
    Any assistance would be much appreciated.
    Thanks,
    Terry

    For a very small office and a minimum of admin and tech know how, one approach i'd suggest is to not worry about user id collisions at all. any time anyone wants to use a mac you just set them up as a user, using consistent names/passwords.
    Have a "Work" volume on each mac that has "ignore ownership on this volume" ticked. that way UID collisions aren't important.
    You can make a Desktop folder on the Work volume and make a SYMBOLIC LINK from every user's home that replaces their desktop with the desktop folder on the Work volume.
    Make it known that the user's home is for personal stuff ONLY, and the Work volume (inc the desktop) is where work in progress lives.
    At a later date with some confidence in your network and your admin skills you could impose consistent UIDs using an OD master

  • I have a pioneer vsx-910-k and airport express.I have a wireless network at home. What's the best arquiecture/config to do with this hardware?

    I have a pioneer vsx-910-k and airport express.I have a wireless network at home. What's the best arquiecture/config to do with this hardware?

    I would suggest that you connect the Pioneer to the AirPort Express Base Station using an optical digital audio cable that has a TOSlink connector on one end and a 3.5 mm optical connector (Mini Plug) on the other. You can then connect the Mini Plug end into the AirPort's audio port and the TOSlink end into one of the Pioneer's optical digital audio ports.

  • Aironet 1231G for home use

    Hi all
    I've been given an Aironet 1231G that I would like to set up for home use. Has anyone got any example configs for this type of setup that I could take a look at? Nothing too complicated is needed, just something simple and secure.
    Thanks
    Andy

    Since you are new to this, just look at this link. You will need to register, but this will help:
    http://downloads.techrepublic.com.com/download.aspx?&scname=Wireless+LAN&docid=277381

  • Old battery for home use and 1 "traveller" battery? good idea?

    My powerbook is my main computer and is connected to the adapter 90% of the time.
    Would there be a noticable benefit from only using the new battery if i need to go on the road and leave the current battery in the laptop for home use?
    If so is it best to leave the new battery half charged when not in use?

    You might want to read this page on the same site as the previous link, because most of my opinions are based on sources like that one, since I am not myself a battery expert.
    So what would you class as a shallow discharge? 50 or
    75%?
    This is going to sound stupid, but I don't really put a number on it, only because I haven't seen one. I only see the advice about shallow vs. deep discharges. But I also don't think it needs to be that precise. The most damaging percentages seem to be 0% and 100%. I am not sure there is so much difference between 50% and 75%. Also, it's pointless to finesse it around that range because if you are on battery and you need to work longer, you should work longer. Being able to use the runtime you bought is more important than ekeing out incremental runtime preservation. I think this is why Apple's advice is so general, because it will essentially accomplish the goal. ("An ideal use would be a commuter who uses her MacBook Pro on the train, then plugs it in at the office to charge.") Unplug it when you need battery, and plug it back in when you don't need battery.
    As the battery will sometimes "rest" for a month or
    more should i follow the apple battery care
    suggestion and leave it at 50% ?
    That seems fine. The page I linked to says 40%. Other sites say 40% and in the fridge. Again, anywhere in the ballpark is probably Close Enough.
    Network, do you leave the battery at a specific
    charge when resting?
    Resting plugged in, 100% obviously, can't do much about that.
    Resting and not in the laptop (short term offline), I aim for 90-95%. The only reason for that is on the site I linked to, it says "The worst condition is keeping a fully charged battery at elevated temperatures," so I figure it's easy to not have it fully charged. However, I will not drain it to 40% for short-term room temp storage, because that would require planning at least an hour ahead to charge it back up to 100% before going out the door. If you forget to do that, you walk out the door with your 40% charged battery, and that 5ucks.
    Resting long-term, I'll drain to around 40%, put it in a ziploc bag, and put it in the fridge. Some say getting it down to fridge temperature isn't important, and I really don't know. But all agree, never put it in the freezer!!!!!
    There is a balance here between convenience and runtime preservation. If you wanted to obsess over runtime preservation you could drain to 50% and fridge it every time you take it out of the laptop, but the reason that's totally stupid is that every time you want to use it you have to get it back up to room temperature and charge it. That's why I like to have different criteria for might-need-it-today storage (almost charged, room temp) and long-term storage (half discharged in the fridge).
    The reason i'm hammering at this is that this
    powerbook is nearing the end of its cycle and i doubt
    i'll invest in another battery in the future.
    Totally understand. That's why I looked into this stuff myself. But since I have a battery that's pretty new, and I think I can get decent runtime out of it for at least 2 years, that means it should last long until the ol' PowerBook G4 feels out of date enough for me to upgrade.
    The main points here are, if you want to use your battery for its intended purpose, don't worry about micromanaging the percentages, just use it normally, don't drain it every time, keep it cool when possible.

  • HT1695 Ipad will not find wireless networks that it used yesterday, but MacBook Pro still finds and uses these networks.

    Our ipad will not find wireless networks that it used yesterday.   Our Mac Book Pro finds them and uses them.   
    we have reset the cable modem and wireless router, turned off the ipad and turned it back on.   Turned wireless off and back on.
    but it just spins trying to find networks but finds none.
    What do do next?

    Settings for wireless network connections are actually stored in two separate places on your Mac, so in addition to the correct advice offered by Jolly Giant, you will also need to delete old network listings in KeyChain Access.
    Macintosh HD > Applications > Utilities > KeyChain Access
    Locate the name of the wireless network that you want to delete and click it to highlight it
    Click Delete on your keyboard
    It would be a good idea to go ahead and also delete the current connection as well in case it has become corrupted. This will clear out the old settings and when you next connect to the network and enter the password, the new settings will be preserved.

  • Setting up Cisco Aironet 1250 for home use

    Hey everyone,
    I'm rather new to the whole Enterprise Router lines. I've set up countless networks with Linksys routers in the past. However, this Aironet is giving me more trouble than I'd want it to. I was wondering if anyone could help. I've assigned it an IP Address and accessed that In-Browser interface and set up an SSID and activated the two extensions. I've been able to connect to the router with my computer and access the internet without restriction. However, when I attempt to connect a second PC or Laptop to the network, it won't allow network access to the second device. I've been stuck there forever. Is there any specific setup method I need to use to make sure more than one workstation/device? I want to use this router for home use, I often use laptops and move around the house a lot, so the advantage of better connection signal and speed is well worth it. Any help is highly apprieciated. If you need more information, don't hesitate to contact me.

    Sorry for my late reply. Here is the config:
    It wasn't connected to anything. This was a raw pull from a fresh cold boot.
    IOS Bootloader - Starting system.
    Xmodem file system is available.
    flashfs[0]: 150 files, 7 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31868928
    flashfs[0]: Bytes used: 6406144
    flashfs[0]: Bytes available: 25462784
    flashfs[0]: flashfs fsck took 16 seconds.
    Reading cookie from flash parameter block...done.
    Base Ethernet MAC address: 54:75:d0:dd:b5:12
    Loading "flash:/c1250-k9w7-mx.124-10b.JDA3/c1250-k9w7-mx.124-10b.JDA3"...##################################################################################################################################################################################################################
    File "flash:/c1250-k9w7-mx.124-10b.JDA3/c1250-k9w7-mx.124-10b.JDA3" uncompressed and installed, entry point: 0x3000
    executing...
                  Restricted Rights Legend
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
               cisco Systems, Inc.
               170 West Tasman Drive
               San Jose, California 95134-1706
    Cisco IOS Software, C1250 Software (C1250-K9W7-M), Version 12.4(10b)JDA3, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2009 by Cisco Systems, Inc.
    Compiled Sun 07-Jun-09 03:50 by prod_rel_team
    Image text-base: 0x00003000, data-base: 0x01000000
    Initializing flashfs...
    flashfs[1]: 150 files, 7 directories
    flashfs[1]: 0 orphaned files, 0 orphaned directories
    flashfs[1]: Total bytes: 31868928
    flashfs[1]: Bytes used: 6406144
    flashfs[1]: Bytes available: 25462784
    flashfs[1]: flashfs fsck took 4 seconds.
    flashfs[1]: Initialization complete....done Initializing flashfs.
    Warning:  the compile-time code checksum does not appear to be present.
    Radio 1 A600 8000 0 0 A8030000 30
    Radio 1 A600 8000 0 0 B8030000 13
    tx_paks 1293
    tx_paks 646
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html you require further assistance please contact us by sending email to
    [email protected]. AIR-AP1252AG-A-K9    (PowerPC 8349) processor (revision C0) with 49142K/16384K bytes of memory.
    Processor board ID FTX1423902R
    PowerPC 8349 CPU at 533Mhz, revision number 0x0031
    Last reset from power-on
    1 Gigabit Ethernet interface
    2 802.11 Radio(s)
    If
    cisco
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 54:75:D0:DD:B5:12
    Part Number                          : 73-10425-06
    PCA Assembly Number                  : 800-27630-06
    PCA Revision Number                  : B0
    PCB Serial Number                    : FOC142025F4
    Top Assembly Part Number             : 800-29039-03
    Top Assembly Serial Number           : FTX1423902R
    Top Revision Number                  : A0
    Product/Model Number                 : AIR-AP1252AG-A-K9
    Press RETURN to get started!
    *Mar  1 00:00:06.211: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
    *Mar  1 00:00:07.039: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
    *Mar  1 00:00:07.543: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
    *Mar  1 00:00:09.587: %SYS-5-CONFIG_I: Configured from memory by console
    *Mar  1 00:00:09.591: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C1250 Software (C1250-K9W7-M), Version 12.4(10b)JDA3, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2009 by Cisco Systems, Inc.
    Compiled Sun 07-Jun-09 03:50 by prod_rel_team
    *Mar  1 00:00:09.591: %SNMP-5-COLDSTART: SNMP agent on host Cisco1250 is undergoing a cold start
    *Mar  1 01:37:52.027: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
    *Mar  1 01:37:52.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Mar  1 01:37:52.707: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Mar  1 01:37:53.467: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Mar  1 01:37:53.467: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
    *Mar  1 01:37:53.847: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Mar  1 01:37:54.467: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Mar  1 01:37:54.695: %CDP_PD-4-POWER_OK: Full power - INJECTOR_DETECTED inline power source
    *Mar  1 01:37:54.703: %DOT11-4-NO_HT: Interface Dot11Radio1, Mcs rates disabled on vlan 0 due to not using AES encryption or
    *Mar  1 01:37:58.303: %DOT11-6-FREQ_USED: Interface Dot11Radio1, frequency 5180 selected
    *Mar  1 01:37:58.307: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
    *Mar  1 01:37:58.307: %DOT11-4-NO_HT: Interface Dot11Radio0, Mcs rates disabled on vlan 0 due to not using AES encryption or
    *Mar  1 01:37:58.311: %DOT11-6-FREQ_SCAN: Interface Dot11Radio0, Scanning frequencies for 13 seconds
    *Mar  1 01:37:59.307: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    *Mar  1 01:38:00.307: %LINK-3-UPDOWN: Interface BVI1, changed state to down
    *Mar  1 01:38:02.931: %LINK-3-UPDOWN: Interface BVI1, changed state to up
    *Mar  1 01:38:11.919: %DOT11-6-FREQ_USED: Interface Dot11Radio0, frequency 2462 selected
    *Mar  1 01:38:11.923: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
    *Mar  1 01:38:12.923: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    Cisco1250>enable
    Password:
    Cisco1250#show running-config
    Building configuration...
    Current configuration : 1717 bytes
    version 12.4
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    service password-encryption
    hostname Cisco1250
    enable secret 5 $1$jDeQ$cFdx0aHAd8wj8tk6CCmXq/
    no aaa new-model
    dot11 ssid Home Network
       authentication open
       guest-mode
    power inline negotiation prestandard source
    username Cisco password 7 05280F1C2243
    bridge irb
    interface Dot11Radio0
    no ip address
    no ip route-cache
    encryption key 1 size 128bit 7 23D0220D02AE7FA723492AA01E34 transmit-key
    encryption mode wep mandatory
    ssid Home Network
    station-role root
    bridge-group 1
    bridge-group 1 subscriber-loop-control
    bridge-group 1 block-unknown-source
    no bridge-group 1 source-learning
    no bridge-group 1 unicast-flooding
    bridge-group 1 spanning-disabled
    interface Dot11Radio1
    no ip address
    no ip route-cache
    encryption key 1 size 128bit 7 0B4935657C801B3620154AB56630 transmit-key
    encryption mode wep mandatory
    ssid Home Network
    dfs band 3 block
    channel dfs
    station-role root
    bridge-group 1
    bridge-group 1 subscriber-loop-control
    bridge-group 1 block-unknown-source
    no bridge-group 1 source-learning
    no bridge-group 1 unicast-flooding
    bridge-group 1 spanning-disabled
    interface GigabitEthernet0
    no ip address
    no ip route-cache
    duplex auto
    speed auto
    bridge-group 1
    no bridge-group 1 source-learning
    bridge-group 1 spanning-disabled
    interface BVI1
    ip address 192.168.0.1 255.255.255.0
    no ip route-cache
    ip http server
    no ip http secure-server
    ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
    snmp-server community Community RW
    bridge 1 route ip
    line con 0
    line vty 0 4
    login local
    end
    They way I connect it in the network is as follows:
    BrightHouse Networks ISP Modem --> Cisco Aironet 1252 --> Incoming connections from computers and laptops.
    Any ideas?

  • HT1424 Is VPN really needed for home use?

    Is VPN really needed for home use on the iPad 2?

    I don't have one. The only times I've seen a need for a VPN is when we've had employees that need to access the work network from home, so need to have a connection that meets the work's security to be granted access to the network (our network is inaccessible outside the building without a VPN)

  • After updating to iOS 6, I can no longer connect to my schools wireless network. It uses manual http proxy. Now however a blank pop up comes up and it will not connect you. Thanks

    After updating to iOS 6, I can no longer connect to my schools wireless network. It uses manual http proxy. Now however a blank pop up comes up and it will not connect you. Thanks

    Turn off your firewall and antivirus software.

Maybe you are looking for