WIRELESS NIC CARD for HP6126UK.

Hi I would like to know what WIRELESS NIC CARD for HP6126UK would be suitable, as i would like to connect to a wireless connection.

Hi:
The easiest thing to do is to purchase an external usb wireless adapter for your PC.
That way you don't have to be concerned with what will specifically work for your PC.
All external usb adapters should work.
Something like this:
http://www.amazon.co.uk/Linksys-Dual-Band-Wireless-N-Adapter-Antenna/dp/B0080K6OXO/ref=sr_1_1?ie=UTF...

Similar Messages

  • Wireless NIC Cards to use with MiFi 2200

    Hello All,
    I've had some issues using the Linksys Wireless-G NIC cards for wireless data access on Windows computers.
    Does anyone know if there are recommended wireless card brands that work best with the MiFi 2200? Thanks for your assistance.

    There are two kinds of RFID tags: Active tags, which have a battery or other internal power source, and passive tags, which have no power source and work by reflecting the energy from an RFID scanner (basically). At the energy levels and distances used for WiFi location detection, passive tags will not return a detectable signal.
    Take a look at http://www.aeroscout.com/ for more info on WiFi RFID tagging.

  • Wireless internet card for powerbook 1400

    Can anyone recommend a wireless PC card for the Powerbook 1400? (I know...an anchient machine but I want to throw it in the kitchen for looking up recipes and other light futy stuff.) I think it needs to be a PCMCIA card or something like that. Thanks.

    Richard,
    You can run an 802.11b 11Mbps PC card on the 1400 with the correct wireless drivers and this is dependent on which version OS you have installed on the 1400. The card you want is the WaveLAN or Orinoco wireless PC card. And if your 1400 were running OS 9.1, you could use Apple's AirPort 1.2 software.
    Here is a more extensive guide to your wireless setup:
    http://www.penmachine.com/techie/airport1400.html

  • Did I buy the wrong wireless NIC card?

    Hello all .... I have a small home network consisting of 3 laptops and 2 desktops ... They were all connected via a WRT54G router with the one desktop farthest away using a wmp11 wireless NIC ..... this particular desktop is approx 75 - 100 ft away from the router ... so far there's been no problems,  but that one machine always showed EXCELLENT signal strength (when you'd over the cursor over the little wireless icon in the systray) ....
    For some unexplained reason (cause I'm dumb) I decided to purchase a new router, I got the Linksys WRT160N ..... well the machine with the wmp11 wouldn't even boot up any more, let alone communicate with the router. So I ordered a new wireless NIC for it, a wmp600N...which I installed and now at least that machine boots! The machine does connect to my network, and appears to run on the internet fine, however my question is now whenever you check that machines wireless status, it always says signal strengt is "Poor" or "Very Poor". I see now (I don't know why I didn't notice it before) that there is yet another wireless NIC for that router, and am now wondering if I bought the wrong nic card. I'm just wondering why my signal went from always showing EXCELLENT to now showing POOR all the time.
    When I first ordered this router off the Linksys site, I remember distinctly specify "RANGE" as one of my requirements, yet when I received it from Linksys the box was clearly marked it was NOT for range.... so I am sorta confused.

    I guess I am just concerned as there seems to be so many networks (routers) around here, there is always 7 or 8 connections available on the list of avail networks and I am just concerned about that one machine connecting to the wrong router when it is booted up ....
    when I was using the wrt54g, and it always showed "Excellent" and the others always showed poor to very poor (1 or 2 bars) ,,,,,,,
    but now with the new router always showing just one or two bars as well on that one machine .... I worry that it may connect to the wrong thing sometime. This wouldn't be such a worry for me IF there were simply an option to set "Connect to this network ONLY" on the nic,
    but there isn't, just a "Connect to preffered network IF in range" ..........
    Not that it matters here is the whole reason I have these machines and routers on a network is because I am severely disabled with M.S. and getting up and down steps to all my familys machines isn't so easy, and that one machine about 75 feet from me is impossible. So I have them all  networked thru the router, and I use a remote control program (called Radmin) to access the various machines from this one laptop.
    I am starting to wonder if the fact that nothing will work when this router is on 20mhz bandwith at all, is indicative of some sort of problem with the router itself? That is funny as the wrt54g was 20mhz only I beleive, and it worked perfectly!

  • Recommended Wireless PCMCIA cards for IBM laptop w/ Airport Extreme network

    Does anyone know the best performing PCMCIA card for use on an Airport Extreme wireless network?
    I have an IBM R40 laptop.

    RHESKE, Welcome to the discussion area!
    Does the WinXP laptop have wireless capability? If so, what have you tried and what were the results?

  • Wireless Net card for old PM G4 Quicksilver

    Hey alllll, does anyone know which non-Apple wirless PCI or even USB card might work with a PowerMac G4 Quicksilver 800mhz?
    Using latest OS etc..
    I don't really want to run cables everywhere in my new clean crisp office...:-))
    Thanks,
    X
    QS 800mhz 1.5GB RAM, Dual Raptors, Radeon 9000    
    PM G4, dual raptors, Powerbook G4, 23inch display, ipod vido, nano and more and more...    

    Xerxes, welcome, see the post below "I NEED A WIRELESS CARD FOR MY MAC".
    Joe
    Power Mac G4 Gigabit Ethernet   Mac OS X (10.3.9)   1.5 GB Ram, ENCORE/ST G4, Tempo SATA, ATI Radeon 9000, Adaptec 4000

  • Need Wireless lan card for L100-179

    Hi guys can any one advise me where to buy a wireless lan card and any advise and installing one please

    Hello
    In my opinion the first step is your local dealer where you have bought the unit. This unit is not known to me but I presume unit is WLAN ready and upgrade with mini PCI WLAN card is possible.
    Other way to find out which WLAN card is compatible with your unit is to contact service partner in your country.

  • Does Apple make a wireless pci card for the G5?

    I have a new Airport Extreme base station, but my PowerMac G5 still has the old airport pci card. Does Apple make an "n" pci card that I can use to swap out my old wireless card?

    No. Apple does not have an 802.11n solution for your PowerMac G5.

  • Which Wireless PCI Card for Quartz g31

    Hi ,
    Ive recently tried to go from an external usb wifi adapter to a pci card based one for my Quartz G31 . Ive bought the dell truemobile 1300 WLAN Mini PC model and although it recognises it , it sits there saying not connected . Ive removed the external wifi driver software etc .  Any ideas ?
    Thanks

    Quote
    although it recognises it , it sits there saying not connected
    You'll need to re-establish the connection to your wireless network.

  • Recommended 802.11n cards for PCs w/ AirPort?

    For PCs, are there any recommended wireless N cards for the AirPort? I know most of the generic vendors (Linksys, etc.) recommend you use their brand of NICs as well.
    As Apple doesn't have PC NICs, what brands are recommended for maximum performance?

    Any wireless card should work, providing that it is "n" capable. Of course the vendors want you to buy their stuff.
    The letters (b,g,n) all indicate versions of the same wireless protocol.

  • Support Redundant NIC cards in a HP server

    Hi
    I would like to connect a HP server with two NIC cards (for redundancy) to two CISCO 2970 switches.
    From the HP site they configured Channel Bonding
    [root@sm36s_donald root]# ifconfig -a
    bond0 Link encap:Ethernet HWaddr 00:14:38:EE:6C:6F
    inet addr:172.23.160.36 Bcast:172.23.160.63 Mask:255.255.255.192
    UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1
    RX packets:563837 errors:0 dropped:0 overruns:0 frame:0
    TX packets:110645 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:49833329 (47.5 Mb) TX bytes:17943723 (17.1 Mb)
    eth0 Link encap:Ethernet HWaddr 00:14:38:EE:6C:6F
    inet addr:172.23.160.36 Bcast:172.23.160.63 Mask:255.255.255.192
    UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1
    RX packets:563837 errors:0 dropped:0 overruns:0 frame:0
    TX packets:110645 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:49833329 (47.5 Mb) TX bytes:17943723 (17.1 Mb)
    Interrupt:25
    eth1 Link encap:Ethernet HWaddr 00:14:38:EE:6C:6F
    inet addr:172.23.160.36 Bcast:172.23.160.63 Mask:255.255.255.192
    UP BROADCAST SLAVE MULTICAST MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
    Interrupt:26
    lo Link encap:Local Loopback
    inet addr:127.0.0.1 Mask:255.0.0.0
    UP LOOPBACK RUNNING MTU:16436 Metric:1
    RX packets:8239071 errors:0 dropped:0 overruns:0 frame:0
    TX packets:8239071 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:670754425 (639.6 Mb) TX bytes:670754425 (639.6 Mb)
    What I have to configure from the Cisco switches site in order to avoid ARP problems?
    Thank you for your support
    Stelios

    Stelios,
    We have had issues when trying to load balance between the NICs. when in active/active, the virtual MAC reflects in both the connected switch ports, and the packets tend to loop between the ports. There will be a lot of Spanning Tree TCNs generated, which can shoot up the CPU. We had a 4507R with SUP IV, which got loaded to 70% when doing load balancing. when we made it active/standby on the NIC, the CPU came down to 1 %...
    so just be careful on this. best way of doing it is active/standby
    hope this helps.. all the best.. rate replies if found useful..
    Raj

  • Buy wireless "n" card?

    hi all,
    where can I buy a wireless "n" card for macbook?

    Well,you don't need a card,it's just an Update. But yes,it won't make your Internet speed faster,it's only about range and your network.

  • Dv4-1551dx need wireless n card

    where would i get a wireless n card for this laptop dv4-1551dx i see its an option. need a part# or a place to buy or both ty

    Intel Wireless 5100 Wifi Link N mini PCI-E Half Height
    Drivers for this Wifi Link 5100 Intel card are here:
    http://support.dell.com/support/topics/global.aspx/support/downloads/en/downloads_splash?c=us&l=en&s...~mode=popup&file=268583

  • How to set up set which NIC card to use for multicast?..

              I just downloaded Rolling Patch 1 for WLS6.0SP2.
              While reading the README file it says
              " ISSUE 42518: Provided a way to set which NIC card to use for multicast traffic
              Can anyone tell me how to set this?. on my WebApplication server it has two NIC
              cards and I want to use the NICcard which is being used to talk to internal network
              for multicast messages.
              One more thing,
              Can anyone one tell how to search for bugs (ISSUES) in weblogic. I am looking
              place where I enter ISSUE number and should get the detailed description of bug/issue
              etc..
              Thanks for helping,
              Nilesh
              

              Thanks Kumar, I'll try this.
              Does this -Dweblogic.interfaceAddress used only for multicast. Or this is also
              used to talk to AdminServer?.
              The other problem I am facing is when I restart the AdminServer in recovery mode
              it's not finding my WebApp servers, because my webapp servers are on public network
              and my admin (management) server is on private network.
              please look at http://newsgroups.bea.com/cgi-bin/dnewsweb?cmd=article&group=weblogic.developer.interest.management&item=1217&utag=
              , for more details about my problem.
              Thanks,
              Nilesh
              Kumar Allamraju <[email protected]> wrote:
              ><!doctype html public "-//w3c//dtd html 4.0 transitional//en">
              ><html>
              >You should be able to do it via console in 6.1
              ><br>Not sure if it was added in 6.0
              ><p>For 6.0 you can set this via command line
              ><br>java -Dweblogic.interfaceAddress=<addr>
              ><p>You need 6.0 SP2 RP1
              ><p>--
              ><br>Kumar
              ><p>Nilesh Shah wrote:
              ><blockquote TYPE=CITE>I just downloaded Rolling Patch 1 for WLS6.0SP2.
              ><br>While reading the README file it says
              ><br>" ISSUE 42518: Provided a way to set which NIC card to use for multicast
              >traffic
              ><br>"..
              ><p>Can anyone tell me how to set this?. on my WebApplication server it
              >has two NIC
              ><br>cards and I want to use the NICcard which is being used to talk to
              >internal network
              ><br>for multicast messages.
              ><p>One more thing,
              ><p>Can anyone one tell how to search for bugs (ISSUES) in weblogic. I
              >am
              >looking
              ><br>place where I enter ISSUE number and should get the detailed description
              >of bug/issue
              ><br>etc..
              ><p>Thanks for helping,
              ><p>Nilesh</blockquote>
              ></html>
              >
              

  • Hi, I bouhgt a used Apple Power Mac G5, I want to buy a blue tooth card for the same to use wireless keyboard and mouse, i am just curious that why do i need to provide the serial number of my computer, is there any compatibilty issue?

    Hi, I am new in Apple Computer, I bought a used Power Mac G5. I want to buy a blue tooth card for the same to use wireless keyboard and mouse. so why it is mandatory to provide the serial number of the machine?

    Hello, Serial# not needed...
    At the Apple Icon at top left>About this Mac.
    Then click on More Info>Hardware and report this upto *but not including the Serial#*...
    Hardware Overview:
    Machine Name: Power Mac G5 Quad
    Machine Model: PowerMac11,2
    CPU Type: PowerPC G5 (1.1)
    Number Of CPUs: 4
    CPU Speed: 2.5 GHz
    L2 Cache (per CPU): 1 MB
    Memory: 10 GB
    Bus Speed: 1.25 GHz
    Boot ROM Version: 5.2.7f1

Maybe you are looking for