Wireless not working HELP PLEASE

Just today my wireless was working perfectly not problems at all. And then i get back from college 4 hrs later and it seems to not work anymore i called cisco and they want to charge me to fix it, and i dont have the money for it. I have tried reseting the router (pressing the small button with a paper clip for 30 seconds). And i have also unplugged it and plugged it back in and still nothing. I called my internet provider and my modem is working fine (im actually writing this with my laptop plugged straight into the modem via ethernet). Could you guys help me out? exams are coming up and i cant keep taking turns using the internet with other people in my house, and i cant keep going to the library to study and do homework. Thanks, you have no idea how thankful ill be if this gets resolved btw i have a cisco linksys E2500 series wireless router
Solved!
Go to Solution.

If you have an extra ethernet cable you may reconfigure the router manually. For step-by-step instructions you may check it out from homesupport.cisco.com. You may also download the setup wizard from this website.

Similar Messages

HP pavilion dv6 microphone not working . help please . . .

HP pavilion dv6 microphone not working . help please . . .

Hi,
DV6 is a series of hundreads of models, what is yours ? To help us answer question quicker, please read this:
http://h30434.www3.hp.com/t5/First-Time-Here-Learn-How-to/Welcome-Get-started-here/td-p/699035
You may wat to try this first:
1. Right click speaker icon (right hand corner)
2. Select Microphone devices
3. Right click Microphone
4. Enable it
5. Click Apply/Ok
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

On my iPhone 5 camera photographed not clear. blurry pictures, autofocus does not work. help please!

on my iPhone 5 camera photographed not clear. blurry pictures, autofocus does not work. help please!

Could you please describe how you are trying to delete a single text message and it will not work? What are you seeing in place of the trash can icon?

When i go in my settings on my ipod touch 3gen it says no wi-fi as in i cant connect to any wi-fi at all i tried to restore but did not work HELP PLEASE

when i go in my settings on my ipod touch 3gen it says no wi-fi as in i cant connect to any wi-fi at all i tried to restore but did not work HELP PLEASE

See:
iOS: Wi-Fi or Bluetooth settings grayed out or dim
If not successful, an appointment at the Genius Bar of an Apple store is usually in order.
Apple Retail Store - Genius Bar

After update.. i can not start the ipad, when i press agree in the terms ...it will freeze and the screen not working///help please

after update.. i can not start the ipad, when i press agree in the terms ...it will freeze and the screen not working///help please

What to Do When Your iPad Won't Turn On
http://ipad.about.com/od/iPad_Troubleshooting/ss/What-To-Do-When-Your-Ipad-Wo-No t-Turn-On.htm
iOS: Not responding or does not turn on
http://support.apple.com/kb/TS3281
iPad Frozen? How to Force Quit an App, Reset or Restart Your iPad
http://ipadacademy.com/2010/11/ipad-frozen-how-to-force-quit-an-app-reset-or-res tart-your-ipad
iPad: Basic troubleshooting
http://support.apple.com/kb/TS3274
iOS: Resolving update and restore alert messages
http://support.apple.com/kb/TS1275
iPad: Unable to update or restore
http://support.apple.com/kb/ht4097
 Cheers, Tom

HT201210 I can not restore my iPhone 4S itunes error says I have 29 and I put it in DFU mode and not working help please

Hello

I can not restore my iPhone 4S itunes error says I have 29 and I put it in DFU mode and not working help please

TS2755 When trying to open my mail, it opens then closes immediately, I've deleted the account and re-created it 3 times and also done a reset but still not working, help please

When trying to open my mail, it opens then closes immediately, I've deleted the account and re-created it 3 times and also done a reset but still not working, help please

Try closing all apps in Multitask Window
1. Double tap the home button to bring up the multi-tasking view
2. Swipe up on the screenshot of the app you want to exit.
3. The app will fly off the screen

Wireless not working - help!

Hi - I lost electric today and when I got home, wireless is gone. I have powered down and up again, wireless still not working. I can see other networks but not mine.
I can hardwire to my computer to get on the internet but don't know how to restore the wireless again.
Can someone help me? I've been waiting on hold on the phone for an hour now...

Seems that you lost your wireless configuration. Easy to fix, but your best bet would be to connect (hardwired) like you are, connect with live chat and let the technicians take over your computer-they will tell you how.
Or you can download the instructions from this site and follow them step by step. Just choose your product and select the PDF document.

Youtube not working help please

i am using macbook pro retina for 1 year now but just a few days ago youtube stopped working suddenly and i thought it was because the site was down or something but i have checked that and found that it is not working just in my macbook
when i open youtube it shows a html format please help guys i have attached the photo ive reinstalled google chrome ,and also flash player with no respite

Go step by step by step and test.
1. Power off the router. Unplug it from the wall. Wait a while.
    Plug it back to the wall. Power the router on. Wait until all the lights are lit properly. It will take a while.
    Restart the computer.
    Start up in Safe Mode.
    http://support.apple.com/kb/PH14204
2. Delete Caches.db
    Close all windows and quit all applications.
    Hold "option" key down and click "Go" menu in the Finder menu bar.
    Select "Library" from the dropdown.
    Library > Caches > com.apple.Safari > Caches.db
    Right click the Caches.db file and select "Move To Trash.
    Close windows and relaunch Safari.
3. Empty Caches
    Safari > Preference > Advanced
    Checkmark the box for "Show Develop menu in menu bar".
    Develop menu will appear in the Safari menu bar.
    Click Develop and select "Empty Caches" from the dropdown.
4. Delete Cookies
    Safari > Preferences > Privacy > Cookies and other website data:
    Click “Remove All Website Data”.
5. Safari > Preferences > Extensions
    Turn off Extensions if any and launch Safari again to test.
    Turn on those one by one and test.

HSRP on 2 3550's not working, HELP please

Hello Everyone,
I am attempting to run and test HSRP but there seems to be some errors.
My first switch is a Catalyst 3550 - 48 Port with SMI image
My second switch is a Catalyst 3550 - 48 Port with EMI image.
I configured HSRP on Vlan12 to try and see if my second switch will take over once I pull the cable out of the first one but it seems like it doesn't.
In the "show standby" command, the second switch shows as "Active router" because I gave it higher priority and it sees the neighbor switch which shows as standby router, so hsrp sees both the switches, knows which one is active and which one is standby but yet when I pull the plug on the first one, network is down, as if it did not revert to the second switch.
My cabling is as follows.
First switch has the first GIG (over fiber) uplink to my provider, the second GIG port is connected to the second gig port on the second switch over fiber as well. The first gig port of the second switch is NOT connected to anything as I only have one provider.
The two ports communicate since hsrp seems the neighbor switches.
The two are configured like this 10.0.0.1 s virtual gateway. 10.0.0.2 is the address of first switch. 10.0.0.3 is address of second switch (backup one). Those IP's are on a MANAGEMENT VLAN which I gave as VLAN ID 100
Now for the VLAN12 I am testing HSRP on, it has VALID INTERNET IP's and not local internal IP's.
Once again, the virtual IP finishes with 225, and I configured 226 as IP on switch1, 227 as IP on switch2.
I am NOT using the track option as I am not sure what it does, I only use the standby priority and preempt options.
So to put it in brief, I am trying to make VLAN12 work with HSRP so that all traffic from VLAN 12 enters switch 1 (from the provider uplink) goes to switch2 since I set vlan12 with higher priority (hsrp) on switch2 goes to the servers, then comes back to switch2, routes to switch1 (since it has to uplink to provider) and out to the internet.
I hope my formatting is not very bad and pretty much understandable.
Can someone please tell me what I am doing wrong and why is hsrp not working for me?
PS: I am suspecting the routing is not done well between one switch and the other so they cannot communicate the traffic, but I am not sure
Please help me
Thank You

Hello,
Ok I am copy and pasting the configs of INTERFACE FASTETHERNET 12, VLAN12 and SHOW STANDY on BOTH 3550's...
NOTE: Port 12 is not connected at this point on standby 3550 to the 2950t anymore as I have disconnected the cable since it was not working, this is why there are less details for interface fast ethernet port 12 on standby switch, if you need full details I can give you more details once I connect it again, even with it disconnected, show standby shows the standby 3550 as active for Vlan12, but yet vlan12 operates out of active 3550 even when port 12 was active on standby one.
For privacy reasons, I have XXX'ed the IP's
Here is the data:
--- ACTIVE 3550 -----------------
interface FastEthernet0/12
description Switch 8 Uplink
switchport trunk encapsulation dot1q
switchport trunk native vlan 12
switchport trunk allowed vlan 1,3,12,100
switchport mode trunk
mls qos trust cos
macro description cisco-switch
auto qos voip trust
wrr-queue bandwidth 10 20 70 1
wrr-queue min-reserve 1 5
wrr-queue min-reserve 2 6
wrr-queue min-reserve 3 7
wrr-queue min-reserve 4 8
wrr-queue cos-map 1 0 1
wrr-queue cos-map 2 2 4
wrr-queue cos-map 3 3 6 7
wrr-queue cos-map 4 5
priority-queue out
spanning-tree link-type point-to-point
interface Vlan12
ip address 2XX.XX.XX.226 255.255.255.224
no ip redirects
standby 12 ip 2XX.XX.XX.225
standby 12 priority 95
standby 12 preempt
Vlan12 - Group 12
State is Standby
4 state changes, last state change 1d08h
Virtual IP address is 2XX.Xx.XX.225
Active virtual MAC address is 0000.0c07.ac0c
Local virtual MAC address is 0000.0c07.ac0c (v1 default)
Hello time 3 sec, hold time 10 sec
Next hello sent in 0.068 secs
Preemption enabled
Active router is 2XX.XX.XX.227, priority 110 (expires in 7.508 sec)
Standby router is local
Priority 95 (configured 95)
IP redundancy name is "hsrp-Vl12-12" (default)
Vlan100 - Group 10
State is Active
2 state changes, last state change 2d03h
Virtual IP address is 10.0.0.1
Active virtual MAC address is 0000.0c07.ac0a
Local virtual MAC address is 0000.0c07.ac0a (v1 default)
Hello time 3 sec, hold time 10 sec
Next hello sent in 0.064 secs
Preemption enabled
Active router is local
Standby router is 10.0.0.3, priority 100 (expires in 9.608 sec)
Priority 150 (configured 150)
IP redundancy name is "Hsrp-Vlan100" (cfgd)
---- STANDBY 3550 -------------------------
interface FastEthernet0/12
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 1,3,12,100
switchport mode trunk
interface Vlan12
ip address 2XX.XX.XX.227 255.255.255.224
no ip redirects
standby 12 ip 2XX.XX.XX.225
standby 12 priority 110
standby 12 preempt
Vlan12 - Group 12
Local state is Active, priority 110, may preempt
Hellotime 3 sec, holdtime 10 sec
Next hello sent in 0.126
Virtual IP address is 2XX.XX.XX.225 configured
Active router is local
Standby router is 2XX.XX.XX.226 expires in 7.756
Virtual mac address is 0000.0c07.ac0c
2 state changes, last state change 1d08h
IP redundancy name is "hsrp-Vl12-12" (default)
Vlan100 - Group 10
Local state is Standby, priority 100, may preempt
Preemption delayed at most a further 0 secs for syncs
Hellotime 3 sec, holdtime 10 sec
Next hello sent in 2.348
Virtual IP address is 10.0.0.1 configured
Active router is 10.0.0.2, priority 150 expires in 7.752
Standby router is local
1 state changes, last state change 2d03h
IP redundancy name is "Hsrp-Vlan100" (cfgd)
Hope this helps you experts to help me :)
Thanks

Wireless NOT WORKING HELP ME!!

all around my house i get wireless connection upstairs downstairs, the basement, even outside (diveway etc) but i recently moved my bedroom to a room above my garage in my home and the Wireless connection that i get everywhere else i cant get in that one room. We tried buying a stronger router. that did not work. I can get a connection further away from my new room, just not in my room. How do I solve this?

Although there is a limit to the functional length of a USB cable in regard to
how a product at the end of it, may (or not) work, you could attempt to use
a USB wireless adapter with the computer in that location, and run a longer
USB cable toward the base station's location, so as to limit the distance from
one to the other. This, to see if there is a way to use wireless and not hardwire.
Probably, overall, a wired Ethernet network would be better once such a thing
were installed; since it is more secure and uses more reliable technologies.
If you have two AirPort Extreme Base Stations, you can link them; to see if a
larger wireless network could result. Mine can do this. Perhaps, to try & use
a wireless antenna or adapter on your portable computer, could help?
And one less source of interruption, depending on how the garage is wired
and what kind of wireless garage door opener is used to activate the door.
Even the extra metal and other built-in structural differences in the garage
could be suspect in contributing causes for no or poor wireless networking.
Metal rain gutters, roof flashings, trim; electrical wires in walls and ceilings,
metal hardware for the garage door, all of these could affect wireless. Any
appliances, such as freezers and other items in the garage, also may do it.
There are some amplified wireless adapters one may try, to see if you can
expand the wireless network, past whatever local interruption exists. Yet,
if there is too much wood, metal, sheetrock layers, or other products in the
walls or overlapping roofs, or long metal items (pipes, downspouts, etc) all
of these items may be acting in concert to block out your wireless.
Within legal limits on how powerful your wireless network can be amplified,
there are some retail products for expanding a wireless network and one
of them is considered a Transceiver; upward of 4 watts. However, it will not
remove structural blocks in the building's construction; and if you expand a
local wireless network power too well, neighbors may be tempted to hack in.
Then, you can try other security methods to hide your network, if it happens!
Probably an Ethernet local network with only a few wireless access points,
made as secure as possible, would be the better way to go. Initially, it may
cost some time, money and effort to install the wires and Ethernet hardware.
Good luck & happy computing!

TS3274 What woud I do if my screen is not responding? I can't unlock my mini ipad because the touchscreen is not working. help please.

Hi guys, please help me. my son's mini ipad cannot be unlocked because the touchsreen is not responding.. help please. thank you.

A reset should help. Tap and hold the Home button and the On/Off buttons for approximately 10-15 seconds, until the Apple logo reappears. When the logo appears, release both buttons.
No content is affected by this procedure.

Ipod mini not working HELP PLEASE!!!!!

my ipod mini is showing the apple logo, a sad face and then a battery sign with a fire bolt when i try plugging it into the computer. also, my computer wont recognize it at all. I've tried resetting and restoring it many times but its not working. what should i do!?!?!?!?! I've tried to make an appointment with the Genius Bar but they are too busy and my warrenty expires really soon!!
HELP!!!!!!
ipod mini Windows XP
ipod mini Windows XP

Hi Ssh,
Welcome to Apple Discussions
You may want to look at...
Knowledge Base Document #61711 on iPod missing in "My Computer" or in iTunes on Windows
Knowledge Base Document #93499 on Windows confuses iPod with network drive and may keep iPod from mounting or songs may seem to disappear
Knowledge Base Document #61003 on iPod shows a folder icon with exclamation point when you turn it on
Knowledge Base Document #61584 goes over When the iPod Only Shows an Apple Logo and Doesn't Start Up
Jon
Mac Mini 1.42Ghz, iPod (All), Airport (Graphite & Express), G4 1.33Ghz iBook, G4 iMac 1Ghz, G3 500Mhz, iBook iMac 233Mhz, eMate, Power Mac 5400 LC, PowerBook 540c, Macintosh 128K, Apple //e, Apple //, and some more... Mac OS X (10.4.5) Moto Razr, iLife '06, SmartDisk 160Gb, Apple BT Mouse, Sight..

Iphone 3G 2.2 earpiece not working HELP PLEASE

Hi, suddenly my iphone earpiece it´s not giving me sound. When I recieve a call people can hear, but I can´t. Also with the voicemail, I have to use the head phones, or the bluetooh. The only way to speak in a conversation with out the head phones it´s to use it in speaker mode. I have tried everything, plug and unplugged many times the headphones (it recognize the it doesn´t have it because when I put it out it says ringer and no headphones ringer in the iphone when I change the volume). The ipod part is working correctly, when I recieve a call or make a call, it stops. The mic is working fine.
Can somebody help me to find where can be the problem? I already reset it, two times, try the plug and unplugged thing, clean the jack trail

No, I restore the phone to factory setting already, I didn´t make the back up, I put as a new iphone, and try to use it with no extra apps, and still not working, how does this part can get damage and everything still working correctly?, I still using it as a phone with the headphones when I not alone and with the speaker when nobody is around, I don´t have an apple store near me, so I have to send it to them by mail, so, I want to do everything I can before to do that.

Simple copy of reports not working - help please

Hello
I have this function that was written to copy a given report object to a given folder. The code is not working - the copyObj = col.Copy(obj,2) appears to be failing.
Can anyone shed some light on this? Thank you in advance!
- Russell
My function:
function CopyReport (objID, DestFolder, iStore)
dim col
dim obj
dim copyObj
on error resume next
'QUERY FOR OBJECT TO COPY
str = "SELECT * FROM CI_INFOOBJECTS WHERE SI_ID = " + objID
set col = iStore.Query ( str )
obj = col.Item(1)
'COPY THE OBJECT
copyObj = col.Copy(obj,2)
'SET THE PARENTID OF THE COPIED OBJECT
copyObj.Properties.Item("SI_PARENTID").Value = DestFolder
'SET THE PARENT FOLDER OF THE COPIED OBJECT
copyObj.Properties.Item("SI_PARENT_FOLDER").Value = DestFolder
'COMMIT THE COLLECTION
iStore.Commit(col)
end function

Hi All
I've resolved the problem with the copy and am posting the code below. I'd appreciate it if it could be placed in the appropriate forum so that it may be a resource for other developers in the future. I've left in all of my debugging/error checking code for reference as well.
- Russell
The working copy function (with loads of debugging code) is this:
function CopyReport (objID, DestFolder, iStore)
'Function CopyReport
'Parameters:
' objID - the ID of the report to copy
' DestFolder - the ID of the destination folder for the copy
' iStore - the InfoStore to use
'Returns: A text string that is displayed in a web page via response.write that includes the
' name of the report if copied or the error information as appropriate.
dim col
dim obj
dim copyObj
dim newCol
on error resume next
'QUERY FOR OBJECT TO COPY
str = "SELECT * FROM CI_INFOOBJECTS WHERE SI_ID = " + objID
set col = iStore.Query ( str )
If Err.Number <> 0 Then
CopyReport = "iStore.Query failed "
CopyReport = CopyReport + " Error: " & Err.Number & " - " & Err.Description
CopyReport = CopyReport & " " & str
Exit Function
End If
set newCol = iStore.NewInfoObjectCollection()
If Err.Number <> 0 Then
CopyReport = "newCol creation error"
CopyReport = CopyReport + " Error: " & Err.Number & " - " & Err.Description
CopyReport = CopyReport & " " & str
Exit Function
End If
set obj = col.Item(1)
If Err.Number <> 0 Then
CopyReport = "OBJ = col.item(1) error "
CopyReport = CopyReport & " " & str
CopyReport = CopyReport & " Error: " & Err.Number & " - " & Err.Description
Exit Function
End If
'COPY THE OBJECT
set copyObj = newCol.Copy(Obj, 2)
If Err.Number <> 0 Then
CopyReport = "copyOBJ error"
CopyReport = CopyReport & " Count: " & col.Count
CopyReport = CopyReport + " Error: " & Err.Number & " - " & Err.Description
' Exit Function
End If
'SET THE PARENTID OF THE COPIED OBJECT
copyObj.Properties.Item("SI_PARENTID").Value = DestFolder
If Err.Number <> 0 Then
CopyReport = "Error setting SI_PARENTID to " & DestFolder
CopyReport = CopyReport + " Error: " & Err.Number & " - " & Err.Description
Exit Function
End If
'SET THE PARENT FOLDER OF THE COPIED OBJECT
copyObj.Properties.Item("SI_PARENT_FOLDER").Value = DestFolder
If Err.Number <> 0 Then
CopyReport = "Error setting SI_PARENT_FOLDER to " & DestFolder
CopyReport = CopyReport + " Error: " & Err.Number & " - " & Err.Description
Exit Function
End If
'COMMIT THE COLLECTION
iStore.Commit(newCol)
If Err.Number <> 0 Then
CopyReport = "Commit error"
CopyReport = CopyReport + " Error: " & Err.Number & " - " & Err.Description
Exit Function
End If
'Return the object info
CopyReport = copyObj.Title
end function
Edited by: Russell L Magidson on Dec 11, 2008 5:12 PM
Edited by: Russell L Magidson on Dec 11, 2008 10:28 PM
Edited by: Russell L Magidson on Dec 11, 2008 10:29 PM

Wireless not working HELP PLEASE

Similar Messages

Maybe you are looking for