Wireless Printing with Netgear Print Server and HP Officejet 6110

Setting up my wife's iMac for wireless printing (Mac is in Kitchen, printer in home office).
We have a Netgear router and her internet connection (wireless) is fine.
I configured the WGPS606 via a Vista laptop and have effectively printed through to the server wirelessly from the laptop.
I downloaded and installed the drivers for the HP printer to the mac and have successfully printed when connected via USB (brought the printer to the kitchen to test)
In adding the IP printer, I am able to set up an IP printer fine, but the HP driver does not appear in the dropdown menu.
I have been able to get the iMac to ping the Print Server and choosing another HP driver does spool, but with gibberish of course.
I believe the problem is that I can't figure out how to get the new driver to appear in the dropdown in the printer settings, which should solve the problem, I think.
Advice?
Thank you.
Message was edited by: Tauria

Unfortunately, there are two kinds of driver on OS X (not like Windows), Carbon and CUPS. To use the CUPS standard network protocols like IP printing, you have to use CUPS drivers. HP doesn't provide CUPS drivers (yet). Install the hpijs 3-part set:
http://www.linux-foundation.org/en/OpenPrinting/macosx

Similar Messages

When printing from Preview, the document prints with large print and many lines added and pages added

When printing from Preview, the document prints with large print and many lines added and pages added. Why does this happen?

Thank you!!! That was the problem--scale was set at 200% (don't know why)--when I reduced it to 100% it printed perfectly.
Thanks again for helping me resolve this problem.

Anything printed with firefox prints too small

anything printed with firefox prints too small. If I print and email it prints in the center top of the page and is just larger than a credit card. if I adjust the scale to 100% the it prints what could fit on one page onto 4 pages and prints a small portion in the center top of the page and is just larger than a credit card.

Ok i think i fixed this issues.
i went to about:config print.print_margin_bottom (and also left, right and top) and right clicked reset (it took out the previous 0.5 value). now the pages look normal on print preview without the large margin

Should my iPhone 1 (iOS 3.1.3) with Bluetooth 2.0 (Handset HSP?) work with wireless earbuds with BT 4.0 and the Headset (and Handsfree, A2DP, AVRCP) protocol? They pair and connect; status bar looks good. But audio always comes out the speaker. Thx.

Should my iPhone 1 (iOS 3.1.3) with Bluetooth 2.0 (Handset HSP?) work with wireless earbuds with BT 4.0 and the Headset (and Handsfree, A2DP, AVRCP) protocol? They pair and connect as expected (with a PIN); status bar looks good and shows Bluetooth active, and I even see the iPhone displays the battery levels of the wireless earbuds. But audio always comes out the speaker. (If I plug in wired headphones into the headphone jack then audio comes into the wired headphones, as expected.) I have rebooted the iPhone; I have had it forget about the wireless earbuds, and repaired and reconnected; I have reset all network settings. Thx in advance.
PS: I understand that more recent versions of iOS have a way to choose where audio output goes (speaker, headphone jack, Bluetooth device). Does this older version of iOS? I could not find an option or setting.

I've noticed this lately as well, with my iPhone 4. I couldn't confidently pin it directly on any particular iOS update, but my iPhone used to automatically connect up via Bluetooth with my Prius's handsfree feature, and now it doesn't. I work with a CE-based device at my job, with Bluetooth capability, and I used to test out that feature by having it discover my iPhone. This no longer works either.
What I have found (not really a solution, but it does work and may be a clue for Apple) is that if I simply go to the Settings app then the General -> Bluetooth screen and let it sit there, it will pair right up with my car within a few seconds. Bluetooth is always on, and always says "Now Discoverable" at the bottom of the settings screen.

Unable to connect hana with sybase replication server and i am not getting ECH plz help

unable to connect hana with sybase replication server and i am not getting ECH plz help

Please don't necrobump/hijack threads: https://wiki.archlinux.org/index.php/Fo … bumping.22
https://wiki.archlinux.org/index.php/Fo … _hijacking
Closing

Does Mountain Lion come with an Apache server and if so how do I access it?

Does Mountain Lion come with an Apache server and if so how do I access it?
On my previous Mac there was a check box for web sharing in the Sharing System Preferences. I used this to experiment with HTML website design. How do I do this on my new Mac?

Thanks for the reply. Others have asked similar questions. I was directed to a user tip page
by etresoftThat gives step by step instructions which should solve my problem.

What is available on new Windows servers that allow you to write scripts that can work directly with Windows, SQL Server, and Exchange Server?

What is available on new Windows servers that allow you to write scripts that can work directly with Windows, SQL Server, and Exchange Server?
a. PowerShell
b. isql
c. osql
d. sqlcmd

All questions seem to be from the interview or a test. I think I even took this test once, it's KForce test.
For every expert, there is an equal and opposite expert. - Becker's Law
My blog
My TechNet articles

HP Q6236A Wireless Print Server and HP Officejet 5610

Has anyone really successfully installed the HP Print Server successfully? I have tried everything I can think of to get it to work and cannot. I have Vista on my desktop where the officejet is installed and I have XP on my laptop. I have a wireless network installed using a D-Link router that has been working for several years. I downloaded the latest drivers for the Officejet and ensured that they were installed on both PCs. I followed the onscreen instructions for installing the Print Server adapter and the PC adapter on both PCs (actually uninstalled and reinstalled several times.
I got the PC adapter and the printer adapter to work one time on the desktop and then could not connect again. I downloaded the updated file for the USB disconnect problem with Vista and still no luck.
Does this HP Printer Adapter really work? I have 3 friends that also would like to have this feature and all have HP computers and HP printers but we can't get support from HP. What a shame! Any suggestions??
Thank you in advance.

I’ve installed it successfully and worked fine so far. I share a printer with other computers.
My wireless access point is Linksys router and configured with WPA2 PSK AES. And the printer is C4280.
The installations were tough and easier. It depends on the client computer situation.
Did you try followings?
Step1. Configure the wireless setting for Q6236.
1. Uninstall all of existed the printer driver and the related software, for make sure.
You can do it that the printer installer run again. Then it should show uninstall option instead of the installation and chose it.
2. Install Q6236 driver with the PC adapter.
3. Do the advanced setup and setup wireless connection. Please refer the manual.
4. Confirm network connection to the Q6236 by the utility.
The utility icon where it is right bottom corner of the desktop gets green mark when the connection is successful.
Step2. Install the printer device driver.
1. Remove the PC adapter from the computer. It is not needed any more. It is only for wireless configuration for Q6236 once. After that, you can store it in the attic.
2. Disconnect the Q6236 network connection by the utility. This is important.
3. Install the printer driver by the installer.
In middle of the installation, the installer should request you the USB connection to the printer. Then connect the Q6236 network connection. Do not connect it before the request.
For another PC to share the printer with the Q6236.
Both of the PC and the printer should be online. And do not put the PC adapter on the PC.
1. Uninstall all of existed the printer driver and the related software
2. Install Q6236 driver.
In the middle of the installation, Q6236 installer should find the printer itself and chose it.
The PC and the Q6236 should be on same IP sub network.
3. Confirm the network connection to the Q6236 by the utility.
4. Do above Step2-2.
If you do not get successful, please tell me which step was problem.

Mac Printing with a printer server and Windows XP desktop

I have the following configuration:
Dell Desktop running XP
Apple iBook G4 running 10.4
Linksys Router
Linksys Print Server
I can't get my iBook to print through the print server. I have tried IP Printing and provided the printer server IP Address and correct printer driver "HP LaserJet 1012 Foomatic/hpijs (which I think is now part of 10.4). When I try to print I get the following message, "Printer Busy; will retry in 10 sec. I have also had Connecting to 192.168.1.78 on port 630... and nothing happens.
Any suggestions? I am at wits end because nothing is working. I know that my wireless router and print server are working because I ping'd them from the PC.
Any help would be greatly appreciated.

On windows, the setup software fills in required info like print server queue name - but we don't have that software on the Mac.
Look in the print server manual and check the supported protocols - LPD and IPP require a queue name which you can find in the manual. HP Jetdirect protocol doesn't need a queue name, and is called TCP/IP raw or socket 9100 printing in some manuals.
Good luck.

Unable to print to kyocera fs-1020D with netgear printer server

Hi,
I have a Kyocera FS-1020D connected to the network via a netgear PS101 printer server. I can see the print server admin page through my browser. I have installed the correct printer driver for the fs-1020d. Every time I try to print to the printer, it pauses and I can restart the printer but when I try to resume the document the printer pauses again.
Thanks for any help.

This topic has been covered several hundred times. Please search for "CUPS print server."

Wireless printing with time capsule 1tb and new wireless all in one printer

I am having problems with printing wirelessly from my time capsule 1tb. I currently have a hp 5510v office all in one printer and drivers can not be found to support printing wirelessly however it can print via usb. What I need is help in picking out a new all in one printer that can print wirelessly from time capsule 1tb. Please help

Hi,
my hp photosmart C6180 all in one works flawlessly with it plugged in to my time capsule all functions.
I used to have it set up using it wirelessly from the printer however for some reason after a update (i think) it stopped working & would not print so had to plug in to time capsule.
Dave

How to set up Canon printer via Netgear print server ps121 on new macbook

I have bought a new Macbook (OS10.4.8). The Apple store gives a good deal if you buy a Canon ip4300 with it but I am having problems figuring out how to set up the printer to work thru my Netgear print server on my Netgear network. Can anybody advise:
1. I know my print server is on port 192.168.1.5, but what kind of settings do I use, IPP or LPT or something else?
2. Why can I not find the driver for the ip4300, even though I have used the CD that came with the printer and run the install program and the printer DOES work when I plug it directly into the USB port. Why does the Macbook come with drivers already installed for only a few ancient BJ Canons and why won't it show me where the driver for the ip4300 is since it is obviously already on the machine?
I know Netgear treats its customers with contempt (Linksys even worse). But I would expect a little more simplicity from Canon and Apple. I know I am an orangutan but it still seems incredibly difficult, as if they have hidden the printer driver on the computer and as if Apple does not want you to install networked printers. Please don't tell me to RTFM, I have read the Canon manual, it tells you how to network with Windows, does not even mention Mac. Any advice appreciated.
Macbook Mac OS X (10.4.8) Netgear PS121, Netgear WGT624v3 router, Canon ip4300 printer

Hi zoevancouver,
If you are not able to set up your Canon MP460 printer, take a look at the article below. There is a link to the Canon website and compatible printers. Since this particular model is not on the list, you may need to contact Canon for additional support.
OS X: Printer and scanner software available for download - Apple Support
https://support.apple.com/en-us/HT201465
Regards,
- Judy

Lost wireless connection with Lexmark Printer

MBPro with 10.8.1. Lost my wireless connection with X6675 Lexmark printer. How do I reestablish the connection. My router is a Time Machine.

Did you solve your printer connection problem? I have the same issue. When I first turn the system on, it is connected. But after a short time (a few minutes?) it loses connection between Mac and printer, even tho both are connected to my WIFI. I have to turn the printer and and off to reconnect it to the Mac. Very frustrating. I have checked Netgear, Printer and Mac settings and can't find any explanation.

Printing with SMC4007ABR Print Server to PostScript Printer

I've just set up my Mac Mini in a new network configuration, with an old SMC4007ABR router/print server printing to my Ricoh Laser AP2100 printer, using IPP printing and the configuration for a Generic PostScript printer, which had worked for this printer in previous setups. I am using the IP address of the router, 192.168.2.1, and the queue name specified in the documentation "lpt1". When I log into the router to view the status page it says the printer is idle and ready. When I submit a print job, I get the message "Network host '192.168.2.1' is busy; will retry in 30 seconds...".
I have tried deleting the printer queue and recreating it, using the queue name with upper case, using the queue name specified for use with Windoze ("LP"), changing the router configuration from DHCP to manual IP assignments and back again, resetting the print system from the Printer Setup Utility, using the CUPS interface at http://localhost:631/ to modify the printer setup in any sane way I could think of. I have looked at anything I could find in this forum that seemed relevant, but haven't found anything to try which I haven't tried. I have tried the SMC technical support system, but the router is no longer supported by them, but by another firm which charges per incident, and doesn't support Macintosh.
I would appreciate any suggestions from people who know idiosyncracies of this router, or who have fruitful insights into this strange behavior. Clearly my Mini sees the printer queue, but not well enough to be able to transmit data to it. Thanks for any insights you can offer.
Regards,
Geoff
Mac Mini Intel Mac OS X (10.4.8)

Thanks very much for your response. It seems I was ignoring the answer in some of the posts I was looking at, having misjudged that they were applying to a different sort of situation. I can't even remember what set of instructions from years ago established such a strong prejudice that I needed the IPP protocol. In any case, I'm grateful for your help.
Best regards,
Geoff
Mac Mini Intel Mac OS X (10.4.8)

How to use AE for wireless printing with Ethernet Printer?

Hi all,
I have been using my AE connected to a printer via USB for printing but have now replaced my printer with another model that only has Ethernet connections.
Can someone please explain how to set up the AE so that I can print? I can get so far but seem to be doing something wrong somewhere. Here's my setup:
Mix of Macs and PC's using Airport Time Capsule for wireless network. Currently setup as 'Create a Wireless Network'
1 x b/g Airport Express - now with Ethernet connection between AE and Printer. Currently connected as 'Join a Wireless Network'
Via 'Add Printer' I have selected 'Internet Printing Protocol - IPP' as the Protocol and added the IP address of the Airport Express '10.0.1.10' as the Address. This seems to connect OK but all I get is printer paused.
Any idea where I am going wrong please?
Many thanks, Mike

Sorry you are having difficulties.
Suggest that you first get the printer working with your AirPort Extreme in case the configuration on the Express may not be quite right.
I'm not familiar with the Epson products, but I do use an HP ethernet all-in-one device.
The basic "must do's" on the device include entering the printers MAC address and assigning a fixed IP address that the printer will always will receive using a DHCP Reservation on the AirPort Extreme. My all-in-one gets 10.0.1.25 It sounds like you may have done this.
After installing the printer software from the disc, you go into the Mac's System Preferencesj > Print and Fax and click the small + (plus) button at the bottom of the printer list. The HP printer appeared immediately as an available printer, so click it to highlight it and then click Add at the lower right. It's been flawless since it was installed about 3 months ago.
You'll need to Add the device for each Mac computer on the network. I don't use PC's but imagine that Add Printer or Add New Device would be the way to go here.
Sometimes it helps to call the manufacturer and endure the hold for 15-20 minutes waiting for the manufacturer's tech support people.

Wireless Printing with Netgear Print Server and HP Officejet 6110

Similar Messages

Maybe you are looking for