Wireless router cant login

I have the WRT54GS wireless router cascaded from another router. I forgot the password for wireless and cant login i tried 192.168.1.1 and 192.168.1.2 and no luck any ideas? thanks

Check from the hardwaired computer what is the default gateway ...... by default it should be 192.168.1.1 .......... Use the same in address bar of browser ....it will ask you for username & password .....
If you had not changed the password of router while installation of the router for the first time ...... then the password is "admin" (without quotes) ..... no username required ....
If it is not working .... you need to reset the router ..... for few seconds ....
After that again try admin password ...........

Similar Messages

Cant access router's login page

my macbook cant access the router's login page,but i cant access the internet through this wifi
here is some info i think may be useful
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
options=3<RXCSUM,TXCSUM>
inet6 ::1 prefixlen 128
inet 127.0.0.1 netmask 0xff000000
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1
nd6 options=1<PERFORMNUD>
gif0: flags=8010<POINTOPOINT,MULTICAST> mtu 1280
stf0: flags=0<> mtu 1280
en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
ether 80:e6:50:00:a0:c6
inet6 fe80::82e6:50ff:fe00:a0c6%en0 prefixlen 64 scopeid 0x4
inet 192.168.2.101 netmask 0xffffff00 broadcast 192.168.2.255
nd6 options=1<PERFORMNUD>
media: autoselect
status: active
en1: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
options=60<TSO4,TSO6>
ether 72:00:04:91:16:20
media: autoselect <full-duplex>
status: inactive
en2: flags=8963<UP,BROADCAST,SMART,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
options=60<TSO4,TSO6>
ether 72:00:04:91:16:21
media: autoselect <full-duplex>
status: inactive
bridge0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
options=63<RXCSUM,TXCSUM,TSO4,TSO6>
ether 82:e6:50:00:cc:00
Configuration:
id 0:0:0:0:0:0 priority 0 hellotime 0 fwddelay 0
maxage 0 holdcnt 0 proto stp maxaddr 100 timeout 1200
root id 0:0:0:0:0:0 priority 0 ifcost 0 port 0
ipfilter disabled flags 0x2
member: en1 flags=3<LEARNING,DISCOVER>
          ifmaxaddr 0 port 5 priority 0 path cost 0
member: en2 flags=3<LEARNING,DISCOVER>
          ifmaxaddr 0 port 6 priority 0 path cost 0
nd6 options=1<PERFORMNUD>
media: <unknown type>
status: inactive
p2p0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 2304
ether 02:e6:50:00:a0:c6
media: autoselect
status: inactive
Internet:
Destination        Gateway            Flags        Refs      Use   Netif Expire
default            192.168.2.1        UGSc           28        0     en0
127                localhost          UCS             0        0     lo0
localhost          localhost          UH             34 2643545     lo0
169.254            link#4             UCS             1        0     en0
169.254.71.63      74:2f:68:73:6d:e   UHLSW           0        0     en0    281
192.168.2          link#4             UCS             2        0     en0
192.168.2.1        94:c:6d:30:49:de   UHLWIir        29      178     en0   1029
192.168.2.101      localhost          UHS             0        0     lo0
192.168.2.102      74:2f:68:73:6d:e   UHLWI           0        0     en0    290
If some people cant help I'll really appreciate.

What I did was a hard reset... (hold reset for 10 or 30 seconds then while holding, unplug unit then release reset button. After 10 more seconds, plug unit back in.)
Between that and using the TFTP program, I was able to get back into my management screen. You will have to reconfigure your router after that. Be sure, if you have a dedicated ip on your computer, you temporarily set it to obtain everything automatically incase your set ip doesnt correspond to the default settings for your router. Then once everything is back up, you can change you ip settings on your PC back to what you had, if any.

Linksys wireless router 160nl cant connect to internet

just bought linksys wireless router 160nl i tried to setup the router up with the software provided and when its installing the router i get an error message
321: eithernet cable not connected. everything is connected and i cant get passed this.
anyone know why?

Hi there,
I just read and posted a solution with the same problem on a WAG320N router.
Check this link...
that might help...
please update us..
cheers
Yesterday is history. Tomorrow is mystery. Today is a gift.

Question about Linksys G Wireless Router and i cant connect my iPod Touch and PSP to it.?

I just got a new Wireless router and it works fine.The model number is WRT54G2. The internet is working and I can go on my xbox live and things like that. The only problem is that my iPod touch and things and my PSP can detect the connection but are unable to join it. Why is this. It was working fine on my previous router. Is there some security thing I have to take off? How do i do this? Thanks in advance

lovemeludo wrote:
Gollum wrote:
From your wired computer, Open setup page of router by typing http://192.168.1.1 in browser’s address bar, and typing password as "admin" and no user name. Goto wireless tab, and wireless security sub tab. Check security key here, and you can disable it as well.
I tried this and it went to a redish gray page that said "401 Unauthorized Authorization required" Help please?
It means you entered the wrong password or username, try some other passwords you might have used if the default admin doesn't work.
"The war between heaven and hell depends on the choices we make, and those choices require sacrifice. That's the test"

Set up belkin wireless router now cant send mail

I set up a belkin wireless router n1 for a thinkpad t61. my primary computer that I'm useing is a imac g5. I went through the tourturus process of speaking with tech support both with verizon for my dsl modem and belkin with the router. I was told and walked through the steps of bridging the modem, whatever that means. why i have to bridge the modem I have no idea. I was told by verizon in order to set up a secure wireless network it had to be in bridge mode.
problem now is that I can send simple e-mail on the mac but when I try to send pictures with e-mails it wont send the mail. is it a problem with bridge mode? Please help if you can. very frustrating not understanding what needs to be done or why im doing it.
thank you adam z.

Change the Wireless Settings on your router and re-connect to your Wireless Network...
To change the Network Name/SSID follow the link here , to change/enable wireless security follow the link here , now check if you can locate the wireless network on your wireless computers and attempt to connect...

Connect to a USB drive linked to my wireless router (non airport express)?

Hi,
i have a USB drive (FAT32) connected directly to my wireless router and I want to connect to the drive from my powerbook. I am able to mount the drive via an ftp link, however the quality of this connection is not as good - iTunes is not able to pick up all my songs saved on the drive.
Does anyne know a better way to connect to this drive. Id like to keep it connected to the wireless router so that the drive and the information is available to everyone on my home network.
The router is a Netgear WGT634U.
Thanks

Yep tried that. but it gives an error and cant connect. (get an error 36 or a login error - but i know the username and password are correct)

HELP! Wireless Router [WRT54G] Suddenly Stopped Working

Hey guys, so over the past 2 weeks i cancelled a previous dsl subscription and i am now with AT&T my activation date was today and at first i wasnt able to connect to the net with my new modem... after chatting with tech suppport they made me login to the modems IP address to configure an email setting which somehow solved my issue i can browse the net perfectly when my macbook is directly connected to the modem with the ethernet cable but when i try to connect the ethernet cable to my linksys wireless router (which worked perfectly fine with the last modem ..) i cant seem to browse the net is there some kind of IP config that i have to do? i dont think the connection itself is faulty since i can successfully log on to the linksys wireless router's ip address and i can also see that connection is at full capacity in the wireless airport connection icon on the top of my window...but when i try to surf the net using the wireless conneciton it kind of just stands still and the page doesnt connect/load... can anyone give me some help pls? thakns

I'm having the same problem today. I've been using this router for a couple of years with no problem. Today the power went out, and now my router can't find the internet. I can connect to the internet if I just plug the modem into my computer, and I can connect my my router wirelessly and get into the setup menus, but the router and modem won't talk to each other. Is there any chance the ethernet jacks on the router fried somehow? When I plug my computer into the router with an ethernet cable none of the 1-4 lights comes on no matter which one I plug into. Is that because they only come on when there is an internet connection, or is there something wrong with them maybe?

I changed the channel on my Belkin Wireless router now my ipod touch 1G can't find my wifi network?

A few hours ago I changed the channel on my Belkin Wireless router for the 1st time. It was either on auto, or channel 6 before, i'm not sure, but I changed it to 11, and now my ipod touch 1G can't find my wifi network. I tried changing it to 6, but nothing, and I also can't go back to auto. Can someone please help. I've already searched for the network, and it says "Cant find network". I've also restarted my router. I also added the MAC address, still nothing. Other than those things, I havent touched anything else. My ipod could connect before just find. My Wifi is not disabled, and it's not on private. I can connect with other wifi's fine. And I can connect to other networks with my ipod, I also held down the button on top, and the home button for 10 seconds to restart and nothing. I also reset my network settings. Please help!

Find the documentation for your router and look up "Reset to Factory Defaults." This process will put the router back to the way it was when you bought it.

P2055dn no longer connects via wireless router

I recently replaced my wireless router, an ancient Airport Extreme, with a Linksys WRT120N, not exactly state of the art but still an improvement. At first I couldn't connect to my p2055dn, which I plugged into the router. It no longer showed up as a Bonjour printer when I tried to add it. Then I changed the network mode setting on the router from Wireless-N to Mixed, which got the printer to show up as a Bonjour printer. I then added it and all was well. Now, however, the printer is again not showing up at all. I can still print directly with an ethernet cable to the printer but not wirelessly. The only thing that has changed is that I had to reinstall OS X 10.10.3, but I don't see why that should have changed anything, particularly since the printer is no longer showing up on our other computers. My inclination is that the problem has to do with the router settings but maybe there's something I can configure on the printer to get it to play nice with the router? Any suggestions very welcome.

OK..
I don't know if this is going to work for all 3 of you or not. Josephlee this might work for you, since you have AT&T DSL. Then again, it might or might not work for any of you. I am currently a BellSouth DSL customer. I had to set my modem to "bridge mode" before being able to use my Linksys WRT54G to access the internet. I can't explain how to set your DSL modem to "bridge mode." Your internet service provider will have to do that. If any of you can get your modem set to "bridge mode" I can give you some advice...
If you can get your DSL modem (Verizon, AT&T, Bellsouth, etc.) set to "bridge mode" this should help you out. By setting your modem to bridge mode, this allows your Linksys router to control all internet access. Basically it opens up your DSL modem to allow any and all internet access straight through it, just like opening a water line. If your modem is set to bridge mode, let's continue...
Open Internet Explorer or whatever web browser you use. Go to http://192.168.1.1 to access your Linksys router's dialog. Hopefully you know the user name and password. The default (factory settings) are:
username: <<< leave blank
password: admin
If you make it this far..
You will be at the Setup/Basic Setup tab
Internet Connection type you want is PPPoE
User Name: is the current login for your DSL account
Password: is the current password for your DSL account
(Remember that your router [not DSL modem] is controlling your access)
Select: Keep Alive and leave default (Not Connect on Demand)
Click on Save (and follow on screen instructions)
Next navigate to the Status tab
Once there, you should see Login Status. It should be Disconnected.
Click the Connect button.
Click Save if prompted. (and follow on screen instructions)
Now.. close ALL browser windows.
Re-open your web browser and check for internet connectivity. Some computers may require a reboot. My Win XP Pro doesn't.
I pray that helps you guys out!

Wireless Router reset. Iphones will no longer connect to Wifi. Help?

My wife recently reset our wireless router and now both our iphones won't connect to the WIFI?
As I look into Settings it looks like it's continuously trying to connect to our network. However it never connects......

I am having the same problem but have not reset our router at all.
when i turn my Iphone4 on it connects for about 10 seconds... then goes to using 3G.
Ive tried resetting network settings, tried selecting join networks>other> and manually put in network and change security to WPA, ive tried resetting my phone, ive tried updating firmware on my wireless router. I dont know what else to try??? my husbands iphone3 is connecting to our wi-fi.
metfreak like randers said aboout logging into ur router... i found our http, username and password on our router, so chk that out for ur login details

Network diagnostics is not accepting the WEP password on my wireless router. I know the password is case sensitive and was very careful in entering it but it still gives me the "Unable to join Wi-Fi Network" error message.

I need help setting up the wireless router for my iMac. I did not know the WEP password when I first turned it on to set things up. Now that I know the WEP password I cant get Network Diagnostics to accept it. I know it is case sensitive and was very careful when I entered the password. What should I do?

Hi, unfortunately WEP is about as secure as a bar of gold lent to a Gang Den! It can be broken in under 30 seconds these days!
If the PW is ASCII, try enclosing it in qoute marks, if Hex try preceding it with the & or % sign.
Also, is the Router set to only allow connect ion to MAC addies of the Interface?

Hi i just bought a wireless router and i cannot get it to...

hi
i just bought a wireless router and i cannot get it to work. it is a wrt54g v6. the power light keeps flashing. I tried talking with linksys to get it fixed, but nothing is working. it says to disconnect from the modem and update my firmware, but i cant get the IP address to come up on the address bar. can someone please help me out.
thank you
angela

If you have just bought the router and it has a flashing power light return the router. It is not worth trying to revive a broken router in that case. Return the router and get a properly working one. I would not want to start with a broker router even if you may be able to revive it. You'll never know what caused the problem and whether you will have more issues later.

Need Help setting up wireless router

Hi, ive spent the week on the phone trying to reach all the various technical support people to help me, and getting no where, i wait forever and then get dropped.
I just got time warner cable in NYC (queens) and the modem and internet surfing works fine if I use a USB cable from the modem to my computer, the problem is the ethernet doesnt work, and I dont have drivers for ethernet, but im more interested in setting up wireless from the modem, to the wireless router to my computer with the wireless card.
I accidently installed some kind of microsoft tcp/ip thingy when surfing around my computer trying to fix this and now I cant use the wireless router and card.
I dont want to spend hours on the phone in a tech support message maze, so please help me thru PM.
Mark
please PM me
(Edited for guideline compliance. Thanks!)
Message Edited by JOHNDOE_06 on 07-15-2007 12:16 PM

Hi Mark, first off let me know are you able to go online directly with the modem, if computer is connected directly to the ethernet port of modem? if not, i think ethernet port of the modem is not working or may be it's defective or drivers for ethernet adapter is not installed , as you've mentioned you can able to go online with the USB cable, once computer is connnected directly to the USB port of modem...unless and untill ethernet port on the modem is not working you won't be able to configure the wireless router... router doesn't have USB port on it... anyways connect modem to the ethernet port of the router >> computer (wireless), reset the router back to factory default settings by pressing reset button on the back panel of the router... release the reset button after 30 seconds, power cycle the network by unplugging power cable of the modem and router... wait for couple of minutes and power up the modem first and wait for few seconds once modem is rebooted, after that power up the router, check the light status power, WLAN and internet light on the router should be on... try connecting to "linksys" wireless n/w from wireless pc...check whether it works or not and let me know...

Infinity and wireless router issues

Hi Folks,
Thanks for taking the time to read this, if anyone has any similar issues or resolutions to the situation feel free to chip in..
We had Infinity installed a while back and noticed some intermittent connection problems, the issue was that wireless connections would suddenly loose the gateway and go offline but unusually it was always fixed by simply restarting the network adapter on the client machine, the wireless signals were always near full strength.
Later on I noticed that although the clients seemed to loose connection it actually appears to loose DNS and keeps existing connections live, example below, meaning that if you had fired up a streaming connection before the 'drop' it would continue to stream to the client perfectly although the client could not access any new connections(online).
The setup we were given on installation consisted of an Infinity wired(only) box that connects to our old wireless router which appears to be acting as a wireless bridge to the Infinity box.
Having been a BBI Tech for a well known ISP Customer Service Centre, using a process of elimination I am guessing that there is an issue between the old router and the new Infinity router that is causing conflicts to crop up.
**Example** A friend working out of the country was using a VNC client to logon to my machine as he couldn't access our DB servers from his location, he became confused when he was using my desktop and suddenly he lost online capability.... even though he was remotely logged into my machine to witness it he couldnt open any websites or connect to any DB's.
I would appreciate any input as im thinking that the best way to fix this would be to buy a new Infinity capable modem with wireless built in, but am reluctant to do so as the standard kit should work after being setup by the engineer..
In summary:-
wireless drops dns with signal full, (not a signal issue)
current connections stay open, (again not a signal issue or problem with the broadband)
cannot open any new connections, (not sure if this is dns based as cant even connect to direct ip's)
the clients have all been fine on other wireless networks, (not just tested on an individual, faulty adapter)
renewing the connection from the client fixes the issue, (something to do with lease times or bad routing maybe?)
The wireless router is one of the black homehubs.
Any help appreciated as im having to write this post using my 3G connection to ensure i dont get dropped.
Thanks
Mike

This is the setup left by the engineer...

Trying to link with PC wireless router

Hi I am newbie to the mac world but picked up a G3 relatively inexpensive (to test before going for a new mac) and I have installed an airport card into it with the adapter and I show that the airport card is working but it is not detecting my wireless router that my other 2 windows pcs are on. It is a Linksys wtr54gs that is wired with ethernet to my desktop pc and wireless to my dell laptop. I am really wanting to get this other pc up and running by this weekend so the kids can use it for back to school which starts next week. It displays that it is sending out a signal but it is not picking up my router. The smae spot in my kitchen where the iMac is my dell laptop gets a perfect signal so it is not that it cant detect there. Someone please help me!!!!!

...as on my dell laptop when i look to the connection it tells me it is hooked to my network called linksystwo
That is no indication of whether the wireless router is broadcasting the network name or not. To connect, the PC must know the name. The PC displays the name of the network regardless of if this feature is enabled or not on the router.

Wireless router cant login

Similar Messages

Maybe you are looking for