Wireless router not allowing full handshake in router mode

This is a follow-up of a question I asked here: https://supportforums.cisco.com/discussion/12180986/rv220w-only-routing-icmp-traffic
I have a recently-purchased rv220w wireless router. My setup is as follows: Internet -> asa 5505 -> 10.0.1.0 subnet -> wireless router (subnet 10.0.3.0, public facing ip is 10.0.1.140).
I can ping between the two subnets fine, but not much else. I did a packet capture with wireshark and noticed something really interesting. If I try to connect from a machine from the 10.0.1.0 subnet to the 10.0.3.0 subnet, say remote desktop for this example, I get a SYN, then a SYN_ACK, and then not ACK back. Only a reset (RST) is getting sent from the machine initiating the connection.
This is super weird. ANy help would please be appreciated. I have the detailed captures if necessary.
UPDATE: I have uploaded the wireshark capture.

For those interested, I have solved this problem, see http://www.reddit.com/r/techsupport/comments/23qsyn/cisco_wireless_router_not_allowing_full_tcp/

Similar Messages

WIRELESS CONNECTION NOT ALLOWED

My WRT160N router will not allow me to connect via WI-FI. On the Linksys EasyLink Advisor...it will not even allow me to select "Wireless Connection" as an option under "Select a Connection Method.
HELP!

pbireton,
What is the operating system of your wireless computers/devices that were not able to connect to the network? I suggest that you set the router's wieless settings. Go to http://192.168.1.1 leave the username blank and type admin as the password. Then go to Wireless tab, set it to Manual and change the Channel to 11. You may actually use other channels like channel 6, 1, 9, and other channels. Choose the onw with the best result.
You may also check this page.
http://linksys.custhelp.com/cgi-bin/linksys.cfg/php/enduser/std_adp.php?p_faqid=3759

Time capsule does not allow me to select bridge mode or manual setup

I've got an Aztech combined router and modem. I have disabled its wireless feature, and from what I have read, understand that I need to set up the Time capsule in manual mode in order to have a bridge connection (?). I've reset the TC several times, but the manual setup option or the bridge connection option does not seem to be available. I can backup fine, but want to use the router facility given the price I paid! If I try to edit the router mode with the TC already setup, the option to change it is greyed out (DHCP & NAT)
Bit of a novice at these things, so any help greatly appreciated!

You need to make sure your ISP supports pppoe as a method of authentication.. if so then you must bridge the Aztech modem.. so it no longer handles the connection.. look up the manual for the modem to find out how to do this.
With the modem bridged.. reset the TC and the airport utility should recognise that it is now needing to run in router mode.. you are running Lion or ML and v6 utility has no manual setup.. it auto sets bridge. You need to force it to router.. but by default from reset the TC will be router.. you then need to setup pppoe client.. have no idea how to do that in v6 utility.. I am pleased to say!!
If you run lion.. download and install the v5.6 utility.. then all your troubles will go away.. it is a tool.. rather than Lion version being a toy utility.
http://support.apple.com/kb/DL1482

HDMI to DVI adapter not allowing full resolution when using Mac OS but does with Windows 8.1

I have a Mac Mini and using the HDMI to DVI cable that came with the computer the maximum resolution it will allow is 1280 x 1024. I have 2 of the same monitors. The other is connected with DisplayPort to VGA adapater and displays full resolution (1920 x 1080) on both monitors but the HDMI to DIV will only show 1280 x 1024. I thought maybe it was my DVI cable or the adapter but when I boot up in Windows 8.1 through bootcamp both monitors display at full 1920 x 1080 resolution. Why does Windows give me the option for full resolution on both but the Mac OS doesn't? All the latest updates have been installed. I've contacted support and all the things they had me do didnt work. I see all these posts with people complaining about the same resolution issues. Is it that difficult for this to work?

Humm... the dual Samsung 21.5" monitor setup on my 2010 Mac Mini running Mavericks works a expected.One is on the HDMI to DVI adapter and the other in on a Kanex Mini DisplayPort to DVI adapter.
Try > Display Menu from the Mac App Store and see if you can select 1920 x 1080 for both monitors using it.
Addtitionally, are you sure that it the HDMI to DVI monitor that is not getting the correct resolution...? Most people are complaining that it is a VGA connected monitor that is not getting the correct resolution.
If it turns out to be VGA connected monitor, then try using a Mini DisplayPort to DVI adapter and DVI cable for that monitor instead of VGA.

E4200 not allowing full internet bandwidth

Hi
I have a 100mb conection and regularly get 90mb plus speed when conected direct to the modem. If I conect via the E4200 I only get 50mb ? I have tried disabling the firewall and QOS but this has had no effect. I am using a wired conection and the latest firmware. Its almost as the E4200 is capped at 50mb throughput.
Anyone got any ideas?
Regards
Dean

You have mentioned that you have the latest firmware on E4200. I assume its 1.0.0.3. Now, did you reset the router after you update the firmware. If not, please do that and reconfigure the router again using Cisco Connect.
These are the steps:
http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=02b368886e424d0daa9a756a75e86bc0_E4200_Frequently_...
Steps to reconfigure E4200 using Cisco Connect:
http://www6.nohold.net/Cisco2/ukp.aspx?pid=93&login=1&vw=1&app=search&articleid=22734&userrole=Links...

OWB does not allow full outer join

I got following error (twice) while validating my mapping: "VLD-1506: Invalid Expression: Mixing full and partial outer joins in one mapping is not supported".
I have following join conditions in my mapping:
1) INGRP1.DISTRICT_ID = INGRP2.DISTRICT_ID And INGRP1.CHARGE_PERIOD_ID = INGRP2.CHARGE_PERIOD_ID And INGRP1.UTL_ID = INGRP2.UTL_ID
2) The same
3) INGRP1.CHARGE_PERIOD_ID (+) = INGRP2.CHARGE_PERIOD_ID (+) And
INGRP1.DISTRICT_ID (+) = INGRP2.DISTRICT_ID (+) And
INGRP1.PROVIDER# (+) = INGRP2.PROVIDER# (+)
I suppose there is not any partial joins here. I tried to make first and second conditions with full outer joins too:
INGRP1.DISTRICT_ID (+) = INGRP2.DISTRICT_ID (+) And
INGRP1.CHARGE_PERIOD_ID (+) = INGRP2.CHARGE_PERIOD_ID (+) And
INGRP1.UTL_ID (+) = INGRP2.UTL_ID (+) And
INGRP1.DISTRICT_ID IS NOT NULL And
INGRP2.DISTRICT_ID IS NOT NULL
If I do this, validation reports the same error, but six times instead of twice.
If I remove outer joins OWB generates following mapping statement:
MERGE
/*+ APPEND PARALLEL(MMB$ACCOUNT, DEFAULT, DEFAULT) */
INTO
"MMB$ACCOUNT"
USING
(SELECT
/*+ NO_MERGE */
"INGRP1"."DISTRICT_ID" "DISTRICT_ID",
DIC$TIME_RECODER."MONTH_ID" "MONTH_ID",
"INGRP1"."PROVIDER#" "PROVIDER#",
"INGRP1"."ACCOUNT_NO" "ACCOUNT_NO",
"INGRP2"."ACCOUNT_NO" "ACCOUNT_NO_1"
FROM "DIC$TIME_RECODER" DIC$TIME_RECODER,
(SELECT
/*+ DRIVING_SITE("AGG"."AGG_INPUT_SUBQUERY"."FC_CHARGES_1_GKH_REL2_GKH_STAR") */
"AGG"."CHARGE_PERIOD_ID" "CHARGE_PERIOD_ID",
"AGG"."DISTRICT_ID$0" "DISTRICT_ID",
"AGG"."PROVIDER#$0" "PROVIDER#",
"AGG"."ACCOUNT_NO$0" "ACCOUNT_NO"
FROM (SELECT
("AGG_INPUT_SUBQUERY"."CHARGE_PERIOD_ID$0") "CHARGE_PERIOD_ID",
("AGG_INPUT_SUBQUERY"."DISTRICT_ID$1") "DISTRICT_ID$0",
("AGG_INPUT_SUBQUERY"."PROVIDER#$1") "PROVIDER#$0",
COUNT(DISTINCT ("AGG_INPUT_SUBQUERY"."ACCOUNT_NO$1")) "ACCOUNT_NO$0"
FROM (SELECT
"INGRP1"."DISTRICT_ID" "DISTRICT_ID$1",
"INGRP1"."CHARGE_PERIOD_ID" "CHARGE_PERIOD_ID$0",
DM_UTILITIES_1_GKH_R14554."PROVIDER#" "PROVIDER#$1",
"FC_CHARGES_1_GKH_REL2_GKH_STAR"."ACCOUNT_NO" "ACCOUNT_NO$1"
FROM {"FC_CHARGES"@GKH_REL2_GKH_STAR} "FC_CHARGES_1_GKH_REL2_GKH_STAR",
{"DM_UTILITIES"@GKH_REL2_GKH_STAR} DM_UTILITIES_1_GKH_R14554,
(SELECT
"DEDUP"."DISTRICT_ID$2" "DISTRICT_ID",
"DEDUP"."CHARGE_PERIOD_ID$1" "CHARGE_PERIOD_ID",
"DEDUP"."UTL_ID" "UTL_ID"
FROM (SELECT
DISTINCT
"FC_CHARGES_GKH_REL2_GKH_STAR"."DISTRICT_ID" "DISTRICT_ID$2",
"FC_CHARGES_GKH_REL2_GKH_STAR"."CHARGE_PERIOD_ID" "CHARGE_PERIOD_ID$1",
"FC_CHARGES_GKH_REL2_GKH_STAR"."UTL_ID" "UTL_ID"
FROM {"FC_CHARGES"@GKH_REL2_GKH_STAR} "FC_CHARGES_GKH_REL2_GKH_STAR" WHERE ( (MAP_DIC$ACCOUNT."DATE_START") <= coalesce ( "FC_CHARGES_GKH_REL2_GKH_STAR"."CHANGED_DATE_#" , "FC_CHARGES_GKH_REL2_GKH_STAR"."CREATED_DATE_#" ) )) "DEDUP" ) "INGRP1" WHERE ( "INGRP1"."DISTRICT_ID" = "FC_CHARGES_1_GKH_REL2_GKH_STAR"."DISTRICT_ID" ) AND
( "INGRP1"."CHARGE_PERIOD_ID" = "FC_CHARGES_1_GKH_REL2_GKH_STAR"."CHARGE_PERIOD_ID" ) AND
( "INGRP1"."UTL_ID" = "FC_CHARGES_1_GKH_REL2_GKH_STAR"."UTL_ID" ) AND
( ( DM_UTILITIES_1_GKH_R14554."UTL_ID" (+) = "INGRP1"."UTL_ID" ) )) "AGG_INPUT_SUBQUERY"
GROUP BY
("AGG_INPUT_SUBQUERY"."DISTRICT_ID$1"), ("AGG_INPUT_SUBQUERY"."CHARGE_PERIOD_ID$0"), ("AGG_INPUT_SUBQUERY"."PROVIDER#$1")) "AGG" ) "INGRP1",
(SELECT
/*+ DRIVING_SITE("AGG_1"."AGG_INPUT_SUBQUERY$0"."FC_PAYMENTS_1_GKH_RE143940") */
"AGG_1"."PROVIDER#$2" "PROVIDER#",
"AGG_1"."DISTRICT_ID$3" "DISTRICT_ID",
"AGG_1"."CHARGE_PERIOD_ID$2" "CHARGE_PERIOD_ID",
"AGG_1"."ACCOUNT_NO$2" "ACCOUNT_NO"
FROM (SELECT
("AGG_INPUT_SUBQUERY$0"."PROVIDER#$3") "PROVIDER#$2",
("AGG_INPUT_SUBQUERY$0"."DISTRICT_ID$4") "DISTRICT_ID$3",
("AGG_INPUT_SUBQUERY$0"."CHARGE_PERIOD_ID$3") "CHARGE_PERIOD_ID$2",
COUNT(DISTINCT ("AGG_INPUT_SUBQUERY$0"."ACCOUNT_NO$3")) "ACCOUNT_NO$2"
FROM (SELECT
"INGRP1"."DISTRICT_ID" "DISTRICT_ID$4",
"INGRP1"."CHARGE_PERIOD_ID" "CHARGE_PERIOD_ID$3",
DM_UTILITIES_GKH_REL2_GKH."PROVIDER#" "PROVIDER#$3",
"FC_PAYMENTS_1_GKH_RE143940"."ACCOUNT_NO" "ACCOUNT_NO$3"
FROM {"FC_PAYMENTS"@GKH_REL2_GKH_STAR} "FC_PAYMENTS_1_GKH_RE143940",
{"DM_UTILITIES"@GKH_REL2_GKH_STAR} DM_UTILITIES_GKH_REL2_GKH,
(SELECT
"DEDUP_1"."DISTRICT_ID$5" "DISTRICT_ID",
"DEDUP_1"."CHARGE_PERIOD_ID$4" "CHARGE_PERIOD_ID",
"DEDUP_1"."UTL_ID$0" "UTL_ID"
FROM (SELECT
DISTINCT
"FC_PAYMENTS_GKH_REL2_GKH_STAR"."DISTRICT_ID" "DISTRICT_ID$5",
"FC_PAYMENTS_GKH_REL2_GKH_STAR"."CHARGE_PERIOD_ID" "CHARGE_PERIOD_ID$4",
"FC_PAYMENTS_GKH_REL2_GKH_STAR"."UTL_ID" "UTL_ID$0"
FROM {"FC_PAYMENTS"@GKH_REL2_GKH_STAR} "FC_PAYMENTS_GKH_REL2_GKH_STAR" WHERE ( (MAP_DIC$ACCOUNT."DATE_START") <= coalesce ( "FC_PAYMENTS_GKH_REL2_GKH_STAR"."CHANGED_DATE_#" , "FC_PAYMENTS_GKH_REL2_GKH_STAR"."CREATED_DATE_#" ) )) "DEDUP_1" ) "INGRP1" WHERE ( "INGRP1"."DISTRICT_ID" = "FC_PAYMENTS_1_GKH_RE143940"."DISTRICT_ID" ) AND
( "INGRP1"."CHARGE_PERIOD_ID" = "FC_PAYMENTS_1_GKH_RE143940"."CHARGE_PERIOD_ID" ) AND
( "INGRP1"."UTL_ID" = "FC_PAYMENTS_1_GKH_RE143940"."UTL_ID" ) AND
( ( DM_UTILITIES_GKH_REL2_GKH."UTL_ID" (+) = "INGRP1"."UTL_ID" ) )) "AGG_INPUT_SUBQUERY$0"
GROUP BY
("AGG_INPUT_SUBQUERY$0"."DISTRICT_ID$4"), ("AGG_INPUT_SUBQUERY$0"."CHARGE_PERIOD_ID$3"), ("AGG_INPUT_SUBQUERY$0"."PROVIDER#$3")) "AGG_1" ) "INGRP2" WHERE ( "INGRP1"."CHARGE_PERIOD_ID" = "INGRP2"."CHARGE_PERIOD_ID" ) AND
( "INGRP1"."DISTRICT_ID" = "INGRP2"."DISTRICT_ID" ) AND
( "INGRP1"."PROVIDER#" = "INGRP2"."PROVIDER#" ) AND
( ( DIC$TIME_RECODER."PERIOD_ID" (+) = "INGRP1"."CHARGE_PERIOD_ID" ) )
) "MERGEQUERY_325"
ON (
"MMB$ACCOUNT"."DISTRICT_ID" = "MERGEQUERY_325"."DISTRICT_ID" AND
"MMB$ACCOUNT"."MONTH_ID" = "MERGEQUERY_325"."MONTH_ID" AND
"MMB$ACCOUNT"."PROVIDER_ID" = "MERGEQUERY_325"."PROVIDER#" )
WHEN NOT MATCHED THEN
INSERT
("MMB$ACCOUNT"."DISTRICT_ID",
"MMB$ACCOUNT"."MONTH_ID",
"MMB$ACCOUNT"."PROVIDER_ID",
"MMB$ACCOUNT"."QNT_CHARGED",
"MMB$ACCOUNT"."QNT_PAID")
VALUES
("MERGEQUERY_325"."DISTRICT_ID",
"MERGEQUERY_325"."MONTH_ID",
"MERGEQUERY_325"."PROVIDER#",
"MERGEQUERY_325"."ACCOUNT_NO",
"MERGEQUERY_325"."ACCOUNT_NO_1")
WHEN MATCHED THEN
UPDATE
SET
"QNT_CHARGED" = "MERGEQUERY_325"."ACCOUNT_NO",
"QNT_PAID" = "MERGEQUERY_325"."ACCOUNT_NO_1";
What does it mean? Is JOINER's full outer join is incompatible with KEY LOOKUP operator and KL should be replaced with WB_LOOKUP_NUM?

Sanders,
Key lookup always does a partial outer join. When the full outer join and partial outer join conditions are put together, there is no available syntax to facilitate it.
The way to this to generate the join operator (with full outer join) first in a subquery, then generate the key lookup as the outer query. Or the other way around, first the key lookup then the full outer join. The important part is that the key lookup can't be merged into the FROM-list.
So there are two workarounds. One is what you already pointed out, using WB_LOOKUP_NUM.
The other is to explicitly spell out the key lookup logic in the mapping by introducing a join with the lookup table, like this.
Change
Table1
.......... Join (w/ foj cond.) ---> KeyLookup
Table2
to
Table1
.......... Join (w/ foj cond)
Table2 ........................ Join (w/ poj cond.) ---> Lookup table
Nikolai Rochnik

LI2323S Not Allowing Full Gaming Resolution?

Hey there, so I'm a complete newbie at this kind of thing so please bear with me. This is my first PC and thus my first monitor in a very long time.
But yeah, basically, with help of my computer nerd friends (who can't seem to diagnose this problem either, oops), I recently purchased a very nice, very expensive gaming/graphics PC. It was custom built through IBuyPower and definitely has that last part. Power. It has a Nvidia 970 graphics card, Intel i5 processor, 16 gb ram, etc. etc. And when I had it hooked up to my 42" TV, I was able to play every game in Ultra/Nvidia settings.
Then I hooked it up to this monitor. Again, I don't know much about monitors and how they work, but should they be able to cap your graphics settings? I can still access Ultra (but not Nvidia) in Far Cry 4. I'm honestly not even sure what Nvidia was, but I'm confused why it would no longer be an option on my monitor vs my TV.
I'm connected through a high speed HDMI cable, the same one I was using with my TV. If you guys have any idea what is causing this/how to fix this, I'd super appreciate it. If not, I'll probably return the monitor and buy another one.
P.S. A little disappointed Lenovo has made contacting them directly so very difficult. You have to Google to find their customer service line (which I didn't have time to call this morning), and I could not find an email. Perhaps I'm blind, but I also wager I'm a pretty Average Consumer, in which case... shouldn't it be easier to find, if I'm having problems? Just a side thought.

Humm... the dual Samsung 21.5" monitor setup on my 2010 Mac Mini running Mavericks works a expected.One is on the HDMI to DVI adapter and the other in on a Kanex Mini DisplayPort to DVI adapter.
Try > Display Menu from the Mac App Store and see if you can select 1920 x 1080 for both monitors using it.
Addtitionally, are you sure that it the HDMI to DVI monitor that is not getting the correct resolution...? Most people are complaining that it is a VGA connected monitor that is not getting the correct resolution.
If it turns out to be VGA connected monitor, then try using a Mini DisplayPort to DVI adapter and DVI cable for that monitor instead of VGA.

Viewsonic 2431wm does not use full width in 1920x1080 mode

HI Folks,
I've recently replaced a failed Viewsonic 2433wm monitor with a 2431wm. My Mac Pro 5,1 has the 1GB Radeon HD5770 video HBA and is a 2 monitor configuration. The previous pair of 2433wm's functioned wonderfully at the 1920x1080@60Hz settings.
However, with the new 2431wm attached, the displayed image does not use the full width of the screen. I've tried manually adjusting the horizontal settings and using the monitor's Auto Image Adjust with no change. I've also installed the latest drivers from the Viewsonic site.
For grins, I borrowed a colleague's 2433wm and it immediately worked as expected with no changes on the monitor or my Mac Pro. Also, setting the 2431wm's resolution to 1680x1024 uses the entire screen width.
Does anyone have tips about the 2431wm or manual OS X settings that could resolve this?
Thanks,
Tim

When using a CRT, the phosphor is painted on the display much more widely. The maximum resolutions used are always far less than the maximum the display could produce IF we were to tune it to absolutely perfectly hit every Phosphor dot. But if you did this, you would have to adjust your display ever time a new picture went up on it.
An LCD display does not wave an electron gun around and light up some phosphor dots. The dots are addressed directly. Optimum resolution is EXACTLY every dot that the manufacturer placed on the glass -- no more, no less.
If you chose any resolution other than the optimum resolution, the display may try to approximate what you asked for and fill the display -- or may not. If it does fill the screen, it will be a poor imitation of the best picture you can possibly get from the display.
My recommendation: Find out what is the optimum or recommended resolution is for your specific display, set your display to that resolution, and do not change it.

HT1414 My new ipad mini does not allow me to switch between modes in the built-camera app. It is stuck on video mode. Can anyone advise?

My new ipad mini will not let me switch between modes when using the built in camera app. It is stuck on Video mode. I am unable to take photos, although I could when I first used it. Could this be a fault with the pad or with the new 7.0.4 update? Can anyone help please?

Have you tried to force quit the app? Double tap the home button. Scroll sideways if needed to see the icon and preview for the camera app. Flip that app up and off the screen to close it then single tap on the home screen preview or single tap the home button to exit the mode.
Try your camera app again and see if you can switch modes.
When you switch modes, you do have to drag the words, not just tap on the video word, if that makes any sense. When you try to go from video to photo, do you try to drag the photo word to the front?

Perplexing Wireless Router Issue! Please Help!

OK Guys and Girls, I could really use some help. I have a wireless router Mod. WRT54G ver. 2.0, and yes it has the firmware upgrade. The problem that I am current having is this, my computer can connect to the router no problem, and i can access the settings too, but it will not let me access the internet at all. It's not the cable modem because I can hook up my laptop to it and get internet. So in short the router isn't, for some strange reason, letting my computer access the internet but the router can access the web. Please any suggestions are welcome. Thank you in advanced.

Access the setup page of the router by launching an
Browser and type on the address bar, 192.168.1.1 and press enter.
When it prompts for the username and password, leave the username field
empty and provide password as "admin" (Without quotes)
click on ok.
On the main setup page the ""Internet Connection Type"" should be
on ""Obtain IP Automatically - DHCP “. Click on the Save Settings
button.
Now click on the sub tab ""MAC address clone"".
- Click on enable
Click Clone & click save settings
Check WAN Ip on Status page of router ....
If getting Valid Ip .... try going online
If not ... power cycle for 4-5 minutes & then again check the WAN Ip address .....

TS1398 My wireless router failed and I had to purchase a new one. My security on the new one will not allow me to use the same password. I entered a new password, but of course it is not on my ipod or ipad mini . How can I enter new password ?

My wireless router in my home has failed. I purchased a new router, but it will not allow some of the characters which I used for my old password. Therefore I cannot access the internet with my ipad mini or my ipod touch. I am unable to change the password on either device. How do I go about changing the password on these units so that I can access the internet? Thanks
Terry Beckingham

http://www.apple.com/support/appleid/contact/

ARRIS NVG599 Wireless Router is not a great product for Gigapower customers!

AT&T your new ARRIS NVG599 Router/Wireless is not a great product for Gigapower customers. The built in wireless on this device really has poor quality. My previous 2Wire589 had a lot better reception and quality. At least when it was a 100% I was able to get full range in my home. With the ARRIS NVG599 coming in default 100% for the wireless the range is very poor to include speed quality with just one wireless device on it. My friend and I who both have gigapower have the save exact issues and live in two different parts of Austin, TX area. Our wireless receiver with uverse keeps freezing and pixelating. Very irritating!!! The tech you sent to my house by the way did an outstanding job in triaging this poor hardware setup you give to your Gigapower customers. I felt bad the for guy because he was stumped just as much as I was. Luckily I was fortunate enough for him to see my issues with the wireless TV box. The tech cleaned the fiber pair. Signal quality was still great before and after the cleaning. Recrimped all copper line. Again Layer 1 is not the issue when it comes to cabling. Only layer 1 issue is the hardware. He even replaced my router with a new one and the wireless quality became worse. He's like the fifth tech to come to my house provide great support since I was upgraded to the new ARRIS NVG599 router. So again this particular model you are giving us really isn't great and I am hoping you all are looking for a better quality product such as the 2Wire or Cisco product. I prefer Cisco quite honestly. I am very disappointed as I never had issues with my 2Wire. Only issue was not getting my true Gigapower speed due to hardware capabilities. You all need to allow your customers to customize their own routers. Why do I have to use AT&T's DNS for DNS? Why can't I use OPENDNS which is a lot more safer my family since we have younger children. I mean if all else fails due to customer issue you can always do a hardware default reset. All if you can stay away from this router they provide as it really is a poor quality of a router and most of product for gigapower customers!

You can change it away from 192.168.1.0/24. But you cannot change it anywhere under 10.0.0.0/8. But 192.168.2.0/24 is fine, and I've heard of people using 172.16.0.0/16 as well.
The DNS is locked in part due to the double (or triple) duty as a gateway for TV. You can always purchase your own router and install it behind the NVG 599 and set it up for whatever DNS and/or subnet you want.

Network diagnostics is not accepting the WEP password on my wireless router. I know the password is case sensitive and was very careful in entering it but it still gives me the "Unable to join Wi-Fi Network" error message.

I need help setting up the wireless router for my iMac. I did not know the WEP password when I first turned it on to set things up. Now that I know the WEP password I cant get Network Diagnostics to accept it. I know it is case sensitive and was very careful when I entered the password. What should I do?

Hi, unfortunately WEP is about as secure as a bar of gold lent to a Gang Den! It can be broken in under 30 seconds these days!
If the PW is ASCII, try enclosing it in qoute marks, if Hex try preceding it with the & or % sign.
Also, is the Router set to only allow connect ion to MAC addies of the Interface?

HT4628 I recently transferred my internet service to another state. Have not yet moved my imac, just my pc laptop. I cannot get my airport extreme wireless router to work. The green light stays lit when everything is connected but I can't connect to the i

I recently transferred my internet service to another state.I have not yet moved my imac, just my pc laptop. I cannot get my airport extreme wireless router to work. The green light stays lit when everything is connected but I can't connect to the internet. Any suggestions?

I would recommend that you do the following as a minimum:
Power-down the modem, AirPort base station, and computer(s).
Power-up the modem; wait at least 10-15 minutes to allow it adequate time to initialize.
Power-up the AirPort base station; wait at least 5-10 minutes. Note: The AirPort's status light may continue to flash amber after it has intialized. That is because, there may be some additional configuration items necessary, like setting up wireless security, before the overall setup is completed to get a green status.
Power-up your computer(s).
If the above steps do not solve the problem, start over with step 1 above, but then perform the next steps between steps 1 & 2. above.
Disconnect the AirPort base station from the Internet broadband modem.
While all of the devices are powered-down, perform a "factory default" reset on the base station. This will get it back to its "out-of-the-box" configuration and make setting it up much easier, especially if you use the "Assist me" process within the AirPort Utility. (ref: Resetting an AirPort Base Station or Time Capsule)
After the base station resets, go ahead and power it back down.
Reconnect the AirPort base station to the Internet broadband modem. For the Extreme and Time Capsule, be sure to connect the cable to the base station's WAN (circle-of-dots) port.
Continue with step 2 in the first set of steps.
In this basic configuration, the AirPort base station will broadcast an unsecured wireless network with a Network Name (SSID) of Apple Network NNNNNN. Network clients, connected to the base station either by wire or wireless, should now be able to access the Internet through the ISP's modem. Once Internet connectivity has been verified, you can use the AirPort Utility to configure the base station for wireless security and any other desired options. Please post back your results.

I have a new wireless router and now my laptop will not recognize the printer.

I recently installed a new wireless router,Linksys E2500, and now my laptop will not connect to my OfficeJet 4500 wireless printer. Operating system is Windows XP. Says it does not recognize the printer. It was working fine with my other Linksys router and I have been able to connect all of my other electronic equipment. Thanks.

You must reinstall the full feature software and drivers again to be sure it will work with the new router. This is the fastest way. Simply follow the instructions that came with the printer.
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired!

Wireless router not allowing full handshake in router mode

Similar Messages

Maybe you are looking for