Wireless setup wizard on hp 7410 all in one doesn't give promt for next step in setting up wireless

The printer is connected to a computer (windows xp) through usb I want to enable the wirless for my laptop (windows 7). I ran the wireless setup wizard and it says searching for available networks then goes back to the home screen. I ran the network utility and the printer doesn't show up but the printer is shown under devices and printers when I click start. The wirless router is a D-Link dir-815 wireless N dual band router. it is 802.11g and a compliant.

Uh, this is a wireless printer, so let's set it up that way:
- Disconnect the USB cable to the printer.
- in Start > All Programs > Hewlett-Packard> [your printer model] > Add a Device.
- Choose to add a Wireless or Network device.
- At one point in the installation it will ask you to TEMPORARILY connect a USB cable. Do so only after it asks.
- Remove the USB cable when it asks.
Now that the printer is wirelessly connected to your network you can do the same procedure with other computers on the network, only you will NOT use the USB cable to communicate network settings to the printer - that has already been done with the first computer.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Similar Messages

HP Officejet 7410 All-In-One Doesn't work after installing Snow Leopard

installed Snow Leopard yesterday ....my HP 7410 printer doesn't work properly ....take a look at the response the HP Service Center gave me:
+Hello Charles,+
+Thank you for contacting HP Total Care.+
+I understand from your email that you want the 'HP Officejet 7410 All-in-One Printer' software driver for 'MAC OS X 10.6'.+
+I appreciate for the opportunity to assist you.+
+*Charles, I regret to inform you that the unit does not support the operating system. I recommend you change the OS to Microsoft Windows to avail the unit software driver.*+
+I will be more than happy to assist you when you change the OS.+
+For information on keeping your HP and Compaq products up and running, please visit our Web site+
at:
+http://www.hp.com/go/totalcare+
Sincerely,
Sentinaro
+HP Total Care+
+Our advice is strictly limited to the question(s) asked and is based on the information provided to us. HP does not assume any responsibility or liability for the advice given and shall not be liable for any direct, indirect, special, incidental or consequential damages in connection with the use of this information. Always back upyour data.+
+For more information, including technical information updates, please visit our Web site at http://www.hp.com/support.+
+HP does not require you to send any financial data in your reply to this email. As a prudent reminder, do not insert credit card details or other financial information in any e-mail replies.+

Help! I've spent hours researching this and can't find a solution...
I upgraded 3 Intel Macs in the house to Snow Leopard last weekend. All went differently...but all were successful. I found that the connection to my HP Officejet 7410 (connected wirelessly to 802.11g Airport Express (AEX) network) was "broken". Deleted then "re-intalled". Documents could now be printed. I then found out scan function was "broken". Figured out how to scan with new Snow Leopard "baked-in" driver and Scan tab...different, but it worked.
Then, tonight, on the eve of my birthday, I was given the green light to purchase an Airport Extreme 802.11n (dual-band) base station (AEBS). I set it up and got 2.5X speed on the two 802.11n laptops in the household. Glorious! Then I went to work to ensure print and scan functions were still operational. Tried to re-connect HP OJ 7410 to wireless network...when it found the network it asked for the "WEP" key (on previous AEX network I was secured utilizing WPA2/Personal)...I entered the WPA2/Personal password (same as previous network) and got the error message "Key must be 5 or 13 characters OR 10 or 26 length with 0-9 and A-F (hex)". So I turned off the wireless radio and instead plugged the 7410 into the AEBS via USB. Deleted the previous queue and re-installed. Found the printer no problem but now without the Scan tab or function anywhere...despite following all the recommendations found both on the HP site and here in the Apple Forums. I print fine. Can't for the life of me figure out what the problem with the now lost again Scan function is.
Only strangeness I can think of is the following: When setting up the network(s), I had the option of naming the 5 ghz band something different. I set mine up with the same name of the 2.4 ghz network with 5ghz in parenthesis (i.e. BobbyG and BobbyG (5 Ghz)).
Sorry for the long post but we need the scan function in the house for my wife's teaching purposes. Any assistance would be GREATLY appreciated.
Very Respectfully,
Bobby G.

HP Photosmart 5520 Wireless Setup Wizard Hangs, USB fails to install

Hello,
I bought a HP Photosmart 5520 4 weeks ago. I installed it and setup a wireless connection. It worked for 1 week without flaws.
After a holiday my HP PS5520 printer lost its wireless connection to the network. I restarted the printer, still no wireless connection. all other devices like iPhones work OK on the wireless network. Tried to run the Wireless Setup Wizard again but the routine hangs (the spinner stops) when searching for routers and no networks are displayed, it hangs. Only a powercord detach can/will hard-restart the printer. After starting the printer, the printer complains that I should us the power butten, but that does not work when it hangs at the wireless setup wizard.
I tried this routine several times, but the printer hangs every time when searching for routers... Tried manual, reset factory defaults, reset network defaults etc... Wireless is simply impossible to use since it can not be setup.
So I tried to use the USB port directly attached to my PC. Since the wireless driver was installed, I connected the printer to the PC with USB but then it was marked as a unrecognised device by Windows 7. I tried to add the HP driver manually but when selecting the CD (inf), Windows tells me that the service stoppen (-10)...
So I installed the software from the CD which pointed me to the online version of the software which I installed. After selecting the USB radiobutton, it tells me to connect the HP PS 5520 which I did, but the HP install window failes to detect that the printer is plugged into the USB port and the printer is installed by Windows as an unknown device.
I uninstalled the 'unknown device' and tried again, wthout luck. Tried another USB port, Windows installed it again as an unknown device and the HP software failes to pick it up. So after googling I deleted all HP software from my computer (Intel I7 - 8 GB), uninstalled the unknown USB device from windows, rebooted several times, deleted all HP folders and cleaned all temp-folders (I am an IT professional!).
So, I installed the software again but when the HPO software asks me to attach the USB cable, Windows again installed the 5520 as an unbknown device and the HP software again failes to see that the printer is attached to the PC.
Tomorrow I will buy a new printer but since this HP 5520 is only 4 weeks old, I really want to knwo how I can fix
1 The issue that the HP printer hangs when searching for routers / wireless networks
2 Windows/HP software to find the HP 5520 through USB
I guess nobody will have an answer since Google does not give any help. This post is merely to expose my frustration that HP makes fine printers but failes to deliver issue-free software... I always have issues when setting up HP printers somehow...
Of coarse I hope that somebody has a clue..... Good night!
Regards
Marc Verkade
Curacao

I have had my 5520 for a couple of years, when intermittently it has dropped off the wireless network, and I have had to reinstall the network. Now it does it every time I switch it on - it has lost the network and password. This is very irritating...

WiFi Wireless Setup Wizard produces Blue Screen of Death on Officejet Pro 8600 Plus

The wireless setup wizard on my Officejet Pro 8600 Plus is failing immediately after "scanning for networks". I get a blue screen of death with error message B8494B00, followed by "turn printer on and off" with flashing screen.
I bought the printer about one month ago and it has worked perfectly so far. My Apple Time Capsule failed yesterday, so I bought a new one (latest model) and had to set up the wireless network again. When I tried to do so on the printer, I got the error for the first time. Nothing else had changed. Other devices are working with no problems on the new network. The computer is an Apple iMac running OS Mountain Lion.
I have tried turning the printer on and off, disconnecting the power and reconnecting, then turning it on again, but no result. I have restored the wireless to factory settings, but no difference.
Please help.

Right off I have to tell you I do not "speak Mac".
I assume the "Apple Time Capsule" is a name for a network router? A syncing device?
Unless I am mistaken:
You do not need the Wizard to set up the network -- it is pretty software for an HP PC; when it works, it can make things easier. The setup Wizard is not necessary for the process. I should think this is true for the Mac.
=====================================================================================
If you cannot get someone from the Printing group to answer your specific concern,
you may have succes with the following:
The User Guide has pretty good detail on how to set up the networking necessary to get the printer connected to either a PC or Mac environment. Assuming you can get the printer to "Reset network settings" (User Guide, page 222), then you can re-enter the information you require manually. It is a bit tedious, but is may work better than fighting the Wizard.
OfficeJet Pro 8600 User Guide
You may be able to circumvent sone or all of this by reinstalling the Full Feature Software for your printer -- that assumes you are first able to "reset network settings", at least, and get a printout test page to verify that the reset actually worked.
Select your printer from HP Office Jet 8600 series
Mac – By Garland_M
HP Wireless Printer Setup (Tutorial Video)
Mac
YouTube Search - HP printer install for mac
Good Luck!
<<< Click on the White Kudos Star on the Left to say Thanks!
Clicking “Accept as Solution" helps others find this fix for a same or similar issue >>>
2013 Year of the Snake!
Kind Regards,
Dragon-Fur

Wireless Setup Wizard not showing up on printer to setup wifi on 1525nw

I am not able to see the Wireless Setup Wizard when trying to get my printer setup on a new network. I would like to reset the printer to factory default settings and need some direction in getting this done. Please help.
Keltex

Hi Keltex,
Indeed a Wireless Setup Wizard is not an available option for the CP1525nw, it support either Wireless Protected Setup (WPS) or wireless setup through the HP software on your PC.
If your new router supports WPS you may use that option from that menu and click the WPS button on your router or your router configuration utility (refer to your router manual for more information) otherwise run the software installation for your printer by selecting wireless connection, you will be prompted to temporarly connect a USB in order to configure the wireless connection.
For any issues, be sure to clarify your operating system.
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

7410 All In One will not connect

I have a 7410 All In One. It's about 3 years old. Within the last 6 months it has been manifesting an ongoing problem. When not in use for a period of time, it will simply stop functioning. Upon disconnecting-reconnecting the power cord, the center screen will illuminate and a white bar across the bottom will appear suggesting it is connecting, but the "On" light will not come on. According the hp site the drivers are up to date.
Another oddity is that when it is in this condition, it will suddenly come back to life. This has happened a couple of times after anywhere from 6 to 12 hours. Unfortunately, it is in this mode now and there are documents that have to be printed.
It has never scanned properly, either, so the All In One functionality is pretty much nil.
Does anyone have any thoughts on this?
Thanks,
WS

Hi YSJA,
I'm sorry to hear you've had problems accessing your Officejet 7410 since adding the AirPort Extreme to your home network.
I have included a link to HP's Wireless Printing Center troubleshooting section. It has section, "Was anything changed or updated on your router recently?" that has detailed steps to help you resolve the issue.
Wireless Printing Center Troubleshooting
http://www.hp.com/global/us/en/wireless/troubleshooting.html
Regards,
Happytohelp01
Please click on the Thumbs Up on the right to say “Thanks” for helping!
Please click “Accept as Solution ” on the post that solves your issue to help others find the solution.
I work on behalf of HP

Fix for HP 7410 All-In-One Freezing after SN Upgrade!

I upgraded to SN and immediately my trusty 2 year old HP 7410 All-In-One went into an endless initialization loop. All it would do was display the HP logo and a continuous progress bar at the bottom of the little screen on the front of it. After no effective solution from the HP site, and nothing that worked here, I went into online search mode and found a blog entry that walks you through getting the device back up and running. It sure saved me $500 that I didn't have to spend!
I'd caution that this worked for me but I have no idea what the root cause was except something to do with the wireless card. The blog gives excellent step by step instructions to disconnect the wireless card connection but if your machine is still under warranty you COULD void that warranty I'd assume. But since this involves a simple unplugging of a connector that can be reconnected it's sure worth a try!
As I mentioned it seems that there's an issue with the wireless card that is somehow responsible for the device locking up permanently as well as it becoming invisible over the network. It becomes unusable over a wireless network as well as via direct USB connection. This shakes it all loose and gives immediate access via USB. There is apparently a few ways to reestablish wireless connectivity but I need to research that a bit more. If/when I find that I'll add another post to this thread.
http://larrycrazyness.blogspot.com/2009/01/hp-fixed.html
After the initial blog entry there are over 150 responses from people that it has worked for including me. I'm not associated with that blog but I thought the information could save many the expense of a service call (that apparently doesn't result in a fix) and the cost of a replacement. Enjoy!

UPDATE: As it stands, I opened the scanner bed and cleaned the glass Home Position strip (for the 6th time now) and low-and-behold, the printer functions properly again.
I know this issue will happen again in a few weeks to a month or so...
My question still stands...
Can ANYONE come up with a permanent solution to repair this issue?
Thanks again in advance.

"Initial Setup of Functional Unit DI all-in-one" not visible in NWA

Hello,
I am trying to configure the functional unit DI using the NWA configuration wizard. I am unable to see the configuration task "Initial Setup of Functional Unit DI all-in-one" in the NWA --> Deploy and Change.
I checked the note 1142136 on how to activate the usage type manually and performed the steps mentioned. However, still I do not see this configuration task.
Could anybody please help me how to perform the initial configuration tasks on the DI?
Thanks.

Hi Divya,
Looks like you already found the /sld/fun alias. The 'Configuration Task' checkbox in the table for the entry 'System Landscape Directory' should be checked. If so, and the config wizard hasn't been run the 'Enable Automatically' button should be available (not grayed out). Click on the 'Enable Automatically' button and the config wizard should start.
HTH.
O.

HP Officejet 7410 All-in-One no longer 'automatically' print double sided

After upgrading my PC from Windows XP 32-bit to Windows 7 64-bit my HP Officejet 7410 All-in-One printer no longer prints double-sided automatically. When sending something to print I am presented with only two options: Print One-Sided or Manually Print on Both Sides. If I choose the latter I have to manually reload the paper when prompted. I have tried searching for updates and downloading drivers but nothing has resolved the problem. I've even gone into printer properties printing shortcuts and changed the settings in "Print on Both Sides" to 'automatically' and still I am prompted to reload the paper. It is a real pain when I have to print a very large slide pack especially when the printer decides to pick up two sheets at the same time. I have spoken to HP and they say my printer is old and they cannot help me. It is about 8-10 years old. Any advice would be gratefully received.

Hello Toosweet
In Printer Preferences make sure the duplexer is enabled. Do you have the full feature software installed?
Don't forgot to say thanks by giving "Kudos" to those that help solve your problems.
When a solution is found please mark the post that solves your issue.

Remove and check cartridge on right error message on 7410 all in one

I recently changed the black ink cartridge in my 7410 all in one printer. After changing cartridge it gave me an error message of " Remove and check cartridge on right". I have tried removing and reinstalling , cleaning connection points with clean damp cloth (water) and still cannot get error message to go away.
Any ideas would be greatly appreciated. Thank You.

NoProblemAtoll wrote:
I know this is an older thread but being it is a top Google result associated with the "Remove and check cartridge on right" error it justifies adding a helpful suggestion for other. Our findings have been HP Printers are very biased against refilled \ recycled cartridges. I own a total of (5)x HP 7310 and HP 7410 printers in my IT Consulting office. These are feature rich MFP’s with an abundant supply of ink available at generously economical prices. On the face of it, it sounds like a good reason to keep a bevy of last gen printers around. EXCEPT the printers work great with the $30-$50 brand new HP brand 96 cartridges from Office Depot or Staples. Unfortunately if you try and buy some recycled cartridges off ebay the Printers detect the recycled\refilled cartridges as a previously depleted HP cartridge that may not be genuine and the units suddenly turn on you. Miraculously the "Remove and check cartridge on right" only manifests itself with non-HP brand cartridges or cartridges that have been refilled. (We have even tried to re-fill out own refreshly depleted cartridges with like results.) Think of it as an HP service reminder conveying you forgot to pay HP their $30-$50 profit on your ink this go round. Remember you need HP Branded ink cartridges (HP = Homogeneously Proprietary). It’s like an intention flaw written into the firmware. Best guess (purely on conjecture) is there is a check in the firmware/drivers for if the cartridges has been previously installed, previously depleted, max install count, and expiration date validation. If it encounters a condition it doesn’t like you get this nondescript error.
[advertisement snipped]
The above post is filled with conjecture and speculation, but is not based on fact. The Officejet7410 is not programmed to reject refilled/reman cartridges. It will check cartridges electrically for various things and will reject cartridges that fail. Typical failures would include a cracked printhead (caused by rough treatment - dropping the cartridge even a few inches for example), or open electrical connections caused by debris on the cartridge contacts. Cleaning the cartridge contacts as shown in the document here may resolve the issue in case of poor electrical contacts.
A cartridge that has been previously used in a different printer will likely be marked as empty, but the printer will happily print with a cartridge detected as empty.
The reality is that the quality of refill and reman cartridges are very variable, but generally poor. The study here has a study conducted by a testing facility, here is another study.
My personal experience has been similar. I donated an HP all-in-one to my son's high school years ago. Sometime later I got a call from the teacher complaining that it was not printing properly. I went and took a look and found they had put in a renam color cartridge that was not printing one of the colors*. They tried another cartridge, which also had a problem and then finally the third cartridge worked. I asked why they used renam cartridges and he said they bought these because they were cheaper. I asked if they were 1/3 the cost....
*The color missing had nothing to do with the printer - blotting the bad cartridge on a damp tissue gave only two of the three colors that would normally be present.
Bob Headrick, HP Expert
I am not an employee of HP, I am a volunteer posting here on my own time.
If your problem is solved please click the "Accept as Solution" button ------------V
If my answer was helpful please click the "Thumbs Up" to say "Thank You"--V

Scan function no longer available in preferences using HP 7410 All-in-One

I have a Mac Book pro running OS 10.9.5. When I select Printers and Scanners in the preferences my HP 7410 All-in-One no longer shows a "scan" selection on my Mac Book. It only shows "Open Print Queue".
It prints just fine and I know it used to show both the "print" and "scan" selection. I don't know when this ability disappeared. Does anyone know what I have to do to get this capability back? I'm not real computer savy so I appreciate all the help I can get.
This question was solved.
View Solution.

Hi,
Click the Apple icon, then About This Mac and select Software Update.
Allow it 30 seconds, then click the top Store menu and select Reload Page.
If there is any HP or Apple update available insall it, reboot your Mac and check if you may scan then.
If the same persists install the following package and check again:
http://support.apple.com/kb/dl907
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

HP 7410 All-in-one identifies itself as a 7310

HP 7410 All in one
Win 7 64bit
Mac
Hi all, first time poster here. Someone threw out a perfectly (almost) good HP 7410 printer. I say "almost" because the printer identifies itself as a 7300 series both on-screen (in both OS's) as well as in the printer report.
Also, the the serial numbers are different:
on the label it reads {Removed for privacy}
The printout reads as: Serial # {Removed for privacy}. Except the WIFI, the 7410 and the 7310 are identical.
All i can guess is that this is a refurb and that someone put a 7310 brain into the body of a 7410.
Is the firmware fried? Can i roll it back?
the printer works great otherwise and no WIFI is no deal breaker, but it'd be nice

Hi,
Well, both series use same manual, as you mentioned only with or without one or two parts:
http://h10032.www1.hp.com/ctg/Manual/c00235090.pdf
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

I just upgraded to mac osx lion and my 7410 all-in-one printer will not work

I cannot get my hp officejet 7410 all-in-one printer to work with Mac OS X Lion

hi,
check this link for Mac 10.7 installation guide.
l0ri3
~Though I work with HP my posts and replies are my own and not from HP.~

Uninstalling the drivers and programs for Windows 7 SP1 64 bit of the OfficeJet 7410 All-In-One

Hi
Which utility should be used to properly and completely uninstall the drivers and programs for Windows 7 SP1 64 bit installed with the OfficeJet 7410 All-In-One printer?
Thanks
Bye
balubeto

Hi @balubeto
I located a software removal utility for you but if you have other HP printers or scanners you may perform the more basica uninstall.
Software and Driver Removal Utility
Uninstalling the Printer Software (more basic uninstall)
I hope this resolves your inquiry.
Please click the Thumbs up icon below to thank me for responding.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Sunshyn2005 - I work on behalf of HP

Error Message flashing on Screen of 7410 All in One

The screen on my officejet 7410 all in one printer fax is flashing the word error (Ox84714145e1) and the auto answer light is alternatingly flashing. We have done the obvious by unplugging everything and trying to reboot but it is frozen. Cannot turn it off with the power button.

Hello there! Welcome to the forums I read your post about the "0x" error code you're seeing on your Officejet 7410. Please check out the link below for the error that might help you! 'Problem with Printhead,' 'Printer Failure,' 'Ink System Failure,' or a '0x...' or a 'C2...' Error Message Displays on the Printer Control Panel If the troubleshooting does not help at all, I would lastly suggest technical support.
Please call our technical support at 800-474-6836. If you live outside the US/Canada Region, please click the link below to get the support number for your region. http://www8.hp.com/us/en/contact-hp/ww-phone-assist.html Happy Holidays,

Wireless setup wizard on hp 7410 all in one doesn't give promt for next step in setting up wireless

Similar Messages

Maybe you are looking for