Wireless site survey doubts with cisco aironet site survey utility tool
Hi,
I have 1131 autonomous AP and we have project where we need to implement WLC 5500 with 1140 LAP.
Before that , we need to do site survey . we are going to use cisco aironet adapter and with the help of site survey utility tool we are planning to do site survey .
I have below doubt before starting the site survey :
1) do we need to configure the AP 1131 with existing LAN set-up of client to get connected ?
If yes , how can i shift this 1131 ap always from one location to another location and connect to respective vlan in switch ? It would be tedious job ....
because , We need to connect ( get associated ) our laptop always to 1131 ap and then roam around to get the RSSI , signal strength , SNR and throughput .... ...
to configure the AP to existing lan set-up of client , it would not be flexible to do site survey ?
without that , how can I just plug-in power to 1131 AP with standalone configuration .... and without connecting to switch ( any lan-port ) , do the site survey ?
Please suggest me .............
In short , without connecting to LAN set-up of client , how can i do the site survey ?
2) will it be worth to do site survey with cisco aironet card ( site survey utility ) ? or we should i have different site survey software for the same ?
Please share the knowledge ....
Site Surveys are important and should be done by a professional. A poor site survey can lead to a lot of problems. It would be hard to put all aspects of conducting a proper site survey in a single post. Lets cover a few of the basics.
1) If you plan to deploy 1140 model access points. Then you should use that AP in autonomous mode so you dont have to be plugged into your network
2) The AP gets powered by an exteral power source like this battery for exmaple:
http://www.tessco.com/products/displayProductInfo.do?sku=345625&WT.mc_id=google_base&sp=true
3) As far as moving the AP around you can purchase a site survey pole like this:
http://www.tessco.com/products/displayProductInfo.do?sku=392506&eventPage=1
4) As for software, I like AirMagnet Surveyor
http://www.airmagnet.com/products/survey/
But again. There is a lot to know about doing surveys...
Similar Messages
-
Which wireless conferencing device comparable with Cisco
Hi
I am fairly new to wireless and need some clarification about Voice conferencing. We have Cisco call manager now my office want make a voice conferencing with other office .we are looking a conferencing device which should be wireless and getting IP via wireless goes through our call manager to other site. Can anyone tell me which wireless conferencing device comparable with Cisco call manager for voice conference and what we have to do to make voice conference.Any help would be appreciated.
(Meeting Room)Voice conferencing device ----->access point----->LAN-àCisco call manager---à
Router -------> Internet cloud ------àRemote site meeting room
Thanks
AminulYou definitely need a WLC/WiSM, that's for certain. Your WLC/WiSM needs to run Mesh IOS/Firmware.
BUILDING IS IN A ROUND SHAPE. WALLS ARE THICK AROUND 20 CM. WE CAN CONNECT ONLY ONE AP TO THE ROUTER WHICH IS ALREADY CONNECTED, OR WE CAN CONNECT ANY WIRELESS ROUTER ITSELF ON THE PLACE OF EXISTING ROUTER.
How do you plan to power up the APs?
Next tricky part is what type of Mesh WAP are needed.
You need 1500 Mesh AP.
Cisco Aironet 1520 Series Lightweight Outdoor Access Points
http://www.cisco.com/en/US/prod/collateral/wireless/ps5679/ps8368/data_sheet_c78-532987.html
Cisco Aironet 1520 Series Lightweight Outdoor Access Point Ordering Guide
http://www.cisco.com/en/US/prod/collateral/wireless/ps5679/ps8368/product_data_sheet0900aecd8066a157.html
Cisco 1520 Series Outdoor Mesh Range Calculation Utility
http://www.cisco.com/en/US/prod/collateral/wireless/ps5679/ps8368/1520_Link_Calculator.xls
NOTE: Try avoid using all caps when typing. It's rude. -
Configuration of a Point to MultiPoint link with Cisco Aironet 1310 bridges
Hi All,
The previous problem of which I started another conversation here:
http://forum.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Wireless%20-%20Mobility&topic=General&CommCmd=MB%3Fcmd%3Ddisplay_location%26location%3D.1ddba023
somehow dissapeared. It could have been a problem of interferences.
I have another issue with other (multipoint) wireless WAN link, which I hope has a solution.
On the central node, we have an Cisco Aironet 1310 bridge configured as root-bridge. It has a panel of four vertical polarity 17 dBi panel 90? antennas, with more than enough gain (there is a 250 mWatts 802.11 b/g amplifier, before the 4-way splitter) and excellent line of sight to three remote bridges.
The three (03) remote bridges are also Aironet 1310 models, confidured as non-root-bridges.
The problem we have is that it seems that when the three remote links operate concurrently the amount of lost packets is huge. When I shutdown the radio interfaces of two bridges, the remaining bridge makes an excellent link with the central node.
It seems that some hours are more critical than others, also the links operate much worse when there is some (small) network traffic in them.
I have read the 1310 manuals, and I can't find a sample configuration for point to multi-point links.
Does someone knows what radio interface configuration should I need to use to establish better quality communication?
I mean, perhaps the 1 x root - 3 x no root configuration is not recommendable for the multipoint link configuration.
Any hints will be welcome.
Best Regards,
Igor Sotelo.Hi All,
Thank you for the information. I configured the distance on the root bridges, but the links showed instability.
I'm using a bi-directional amplifier. It has two pieces. According to the manuals, one is installed indoors, the other outdoors. I'm not sure if the indoors piece has the transmition module or it's only the injector.
We could establish connection at 7 km (around 4 milles) distance from the central point, using 24 dBi antennas on the other side.
However, we have issues with a near located point that is only 1.2 Km (around 0.8 milles) away and has a 13 dBi integrated patch antenna. The signal strenght value we get there is in the -62 to -68 dBm range, and is noticiably (5-10 dBm) lower than the strenght we get at other points of the link. And I have trouble establishing a high quality link with that point, using OFDM modulation. I tend to think that if I remove the amplifier I'm not going to reach that point at all. The EIRP on the central iste is 34 dBm / 2.5 watts, without amplifier it would be 26 dBm / 0.4 watts.
On the opposite sites the EIRP is 33 dBm / 2 watts using CCK or 28 dBm / 0.63 watts using OFDM.
When one looks at the central site from that point, an Motorola Canopy with passive reflector (EIRP 48 dBm or around 64 watts) can be seen. It doesn't have the same direction, but the opposite site must be large distance and could interfere with my wireless network. Attached is an amplified photo of the view. It's safe to assume that the Canopy operates in the 2.4 GHz frequency range.
Once I connect the point at 1.2 Km, the multipoint link loses its quality, and soon the lost packets get too frequent.
The CCK seems to be much more interfered than OFDM, I guess because of that canopies.
Another thing I'm wondering about is if the Aironet 1310 can continuosly switch CCK-OFDM over the same point - multipoint link, without losing packets.
What other parameters should I tweak? Is there a way to avoid interferences fromt the canopy?
I would like to apply 100 mWatts local power using the radio with OFDM, but it seems that's not possible.
Best Regards,
Igor Sotelo. -
Linksys WRT54G with Cisco Aironet antennas
Hi Cisco users,
I've got a small project:
I need to provide a wireless network from a farmhous to a piggery:
Distance about 40 metres, no obstructions
Equipment: Linksys WRT54G v3.1
When i place the wrt54g to the most far point of the house (towards the piggery) i get a fairly stable signal of around 11Mbps
I want to strengthen the signal via an external antenna, preferrably outdoor.
i'm thinking of this antenna:
Cisco Aironet 8.5-dBi Patch Antenna (AIR-ANT2485P-R)
http://www.cisco.com/en/US/docs/wireless/antenna/installation/guide/ant2485.html
or the same one as above only with 6 dBi.
http://www.cisco.com/en/US/docs/wireless/antenna/installation/guide/ant2460.html
Both the linksys and cisco aironet antenna's has RP-TNC connectors.
My questions:
1: Can cisco aironet antenna's work with a linksys wrt54G, based on the same connectors.
2: Is the antenna strong enough? can i cover a distance of 40/50 meters with this antenna, or with the 6dBi version?
3: it's a directional antenna. the piggery is straigh ahead of the farm house. How much beam width do i have on the end of the signal for coverage?
4: maybe i need an extension cable. is this the right one?
Cisco Aironet 5-ft, low-loss, 2.4-GHz RF cable with RP-TNC connectors (AIR-CAB005LL-R)
http://www.comegacity.com/networking-wireless-b-bn/antennas-cables/cisco-air-cab005ll-r-aironet-5-low-loss-cable
Thanks in advance.The connector has to be the same but also the impedance. Cisco APs are at 50 ohms. Not sure about linksys ...
Otherwise if you put the antenna outdoor and there is no obstacle, 40/50m should be reached with those antennas. Take the lowest length of cable possible to put the antenna outdoor though as cable brings loss.
I can't comment about if the 6dbi will be enough as this would require experience with the same hardware which I don't have.
My 2 cents
===
don't forget to rate answers that you find useful -
Hello,good day problem with Cisco aironet 1040 series acces point
Hello good day to all, how to configure cisco aironet 1040 series using web configuration attaching through patch cord without using the console.
if possible please send me step by step instruction, any help is gladly appreciated.
thank you in advance, More power
melhelo good day sir,
this is the first time i configure this device i am using Cisco aironet 1040 for our wireless using POE for power, and using cisco catalyst 2960 as switch
i jack the patch cord in and its goes on colored green,
the thing is how i can configure the aironet 1040 sir?
waiting for a step by step instruction,
thank you in advance
mel -
Cisco Aironet Site Survey Utility with Windows Vista
Where can I download the Cisco Site Survey utility that is supported by Vista?
I to do wonder about this. It would be grand to get an answer from someone at Cisco about this..
-
Severe Site Slow-Down with multiple DNS/Sites
Alright.. this is a bit of a strange situation, any help is appreciated because I'm pretty much out of troubleshooting options.
Mac OS X Server hosting a few important sites and then several "redirect" sites.
- A PHP/MySQL system
- 2 normal PHP/MySQL websites
- 8 Redirects (domain.bz, domain.biz, domain.name, etc..)
The redirects are set up like so:
- A DNS entry with a "www" alias pointing to the local machine.
- A site with a .html file containing a meta-refresh to domain.com
The Redirects work just fine when they are enabled, www.domain.biz goes to www.domain.com, etc.. however, the 3 sites that run on the server experience severe slow-down to the point of not even loading.
Normally the sites are blazingly fast..
Anyway, if the redirect site entries are disabled, the slow-down disappears.
As an added oddity.. if Safari is experiencing the slowdown, but I cancel the site load.. the site pulls up missing images/css in varying degrees, depending on when I cancel, so it's like something is "hanging".
There's nothing apparent in the error logs other than a report that 'there is a mismatch between the domain name and reverse DNS' etc.. 'may cause some services to not work properly'.Nevermind, I found the problem.
The performance cache was enabled for the redirect sites. -
Slow connection with Cisco Aironet 1040
I have been racking my brain for a while and cannot figure out why I am not getting 144Mbps out of my Aironet 1040. I was reading a previous thread (
https://supportforums.cisco.com/thread/2141961) and set it up exactly like it said. I have set the encryption to Cipher AES CCMP and set the SSID to open authentication. I also set the SSID's key management to enable WPA (WPAv2).
I was reading that WMM has to be set. I have 3 options: Disabled, Legacy, and dot11d. If i chose dot11d I have to put in a coutry code. Problem is there are no options in the country code pull down. I cannot even manually type it in.
Another problem is that cell phones cannot connect. It keeps saying authentication fails in the log.
Any reason why I am having such slow speeds?WMM is enabled by default, or at least it should be.
What type of client are you using? Check the specs of the WNIC, and see how many spatial streams that it supports.
HTH,
Steve
Please remember to rate useful posts, and mark questions as answered -
We currently own several Cisco aironet cards which we do site survey's with. As a company standard our laptops were replaced with new laptops which did not include type II pcmcia slots. Is their a solution for the express 34/54 slots to work with the Cisco aironet site survey software?
I have seen PCMCIA to USB adapters but I think they need to be cutom made for each type of PCMCIA card. Does anyone know of a suitable adapter?
-
Cisco Aironet 1200 wireless network very slow
I have a simple wireless network set up, 2 - Cisco Aironet 1200 AIR-AP1220B-A-K9 wireless access points with 2 dBi Diversity Omni directional Ceiling Mount Antennas. They are the only devices connected to a Multitech Routfinder router, the WAN side the router is connected to a dedicated DSL connection. They are powered by AIR-PWRINJ3 power injectors. The WAP get the IP address from the DHCP in the router.
When connecting to the wireless network it runs very very slow, the signal strength is excellent and the connection speed is 54 mbps. But when opening a web browser it takes for ever to load a simple page like msn.com. If I connect the notebook directly to the router it runs very fast. We have tested with several notebooks and have the same problem. When I view the available wireless networks in range the only two that show up are the two Cisco 1200 WAP.
I have done the following with no improvement:
Change the channels from auto to 6 on one and 11 on the other.
Reset to factory defaults.
Update the firmware to c1200-k9w7-tar.123-7.JA2.tar
Replace the 802.11b radios with 802.11g radios AIR-MP21G-A-K9.
Disable the Aironet extensions.
Following is the configuration from one of the access points (before the firmware update):
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname MMA1
aaa new-model
aaa group server radius rad_eap
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa authentication login default local
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authorization exec default local
aaa authorization ipmobile default group rad_pmip
aaa accounting network acct_methods start-stop group rad_acct
aaa session-id common
username xxxx privilege 15 password xxxx
username xxx privilege 15 password xxxx
ip subnet-zero
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
ssid MMA1
authentication open
guest-mode
speed basic-1.0 basic-2.0 basic-5.5 basic-11.0
rts threshold 2312
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 192.168.10.100 255.255.255.0
no ip route-cache
ip default-gateway 192.168.10.1
ip http server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag/ivory/1100
ip http authentication aaa
bridge 1 route ip
line con 0
line vty 5 15
End
Any suggestions would be greatly appreciated.
Best regards,
RandyThanks for the info.
The documentation say not to switch from auto to full duplex or half duplex when using inline power, well I think it says the AP may reboot. I may have tried half duplex before I upgraded the firmware.
While upgrading I disconnected the AP, used a patch cord to connect it to the router and pluged the power directly into it to make sure the wiring to the AP was not the problem and it did the same thing.
However, when trying to upgrade the firmware it took ~ 45 minuets to upload the image and filed a couple of times retrying. I connected the AP to the notebook directly with a crossover cable and it uploaded in about 45 seconds.
That got me to thinking that there may be a problem with the router so I have replaced it with a Linksys.
In the mean time the DSL went down yesterday so I have not been able to test the new setup.
The cables are T568B
W/O
O/W
W/G
B/W
W/B
G/W
W/B
B/W
Best regards,
Randy -
Using Quota templates with Self Service Site Creation
I am having an issue with quota templates not getting assigned to site collections created with Self Service Site Creation.
I set up a quota template in 'Specify Quota Templates' and give it the name 'test'. I then go to self service site creation management and select the name 'test' from the 'Quota template to apply' dropdown. I then create a site using self service
site creation and when completed no template is applied to the new site collection. I am wondering if anybody has seen this or if not am I incorrect in what I am expecting, that is that all site created in that web application should have the quota template
applied that I selected in self-service site creation management
Steven Albrecht
University of Colorado Denver
Steven AlbrechtHi Steven,
Please create a quota template named "Personal site" and apply in self service site creation page, then check again.
http://blogs.msdn.com/b/jimmiet/archive/2012/07/22/10332361.aspx
http://danmyhre.wordpress.com/2010/03/16/my-sites-do-not-have-a-quota-when-they-are-created/
Thanks
Daniel Yang
TechNet Community Support -
Cisco Aironet FW 15.2 Does not work with Non-Cisco Media Bridges
I have a Cisco Aironet 1142i that was just updated from 12.4(23c)JY to 15.2(4)JA1 (don’t think model matters as the issue seem to be the firmware) and now I cannot get my media bridges (3 different ones) to either connect to the 1142 AP or obtain and pass the DHCP addresses to other device connected to the built in switch. If I reload the 1142 AP firmware to 12.4, than this works fine. I have not seen anything in the release notes that changed how this works or if there is I could not find it.
Does anyone know why this changed and if there is any settings that I need to enabled / disable?
Any help on this would be greatly appreciatedMore info to add to this.
AIR-AP1142N-A-K9 Hardware Version of v06 works with firmware 15.2.
AIR-AP1142N-A-K9 Hardware Version v05 does not work with firmware 15.2, but will when downgraded to firmware 12.4.
I'm also having this issue with Cisco Aironet 3602 Fw 15.2(2)JB and 3502 Fw 15.2(2)JB$ that's on a Cisco 2500 WLAN Controller Sw Ver. 7.4.100.0.
Any help on this would be greatly appreciated -
Cisco aironet 1130 and Intermec CV30
Hi to all,
I've a little problem with three Cisco 1130 AP. Anticipately i tell you that i'm not a guru of cisco wireless, but my implementation is very simple. I need a roaming for the 3 AP. I only have Ap, so i configure one as Master Ap and the others like repeater with cisco aironet extension configured. All 3 on the same channel and only the Master one broadcast SSID. Wep security implemented. My Cv30 terminals randomly loose the signal also if they're near an AP. They use windows mobile but i think is only a wrong config problem. I need help. Thank you very much.
AlexThe device is using the LWAPP image.. please upgade the same to autonomous image and convert the same..
Please use the below doc that i hv written and this will helpu!!
https://supportforums.cisco.com/docs/DOC-14960
Please dont forget to rate the usefull posts!!
Regards
Surendra -
Configuring Cisco Aironet 1140 for Radius and setting up a Radius server
guys i need some help setting up my Radius to work with cisco aironet 1140, i am new at this however i was tasked with setting up a Radius server and setting our AP with WPA2- enterprise so users can log into our AP using AD credentials.
When i try to setup on the AP a new SSID i do not see the option for WPA2- enterprise?Here are other links with examples:
https://supportforums.cisco.com/thread/331581
http://targetcisco.blogspot.com/2011/03/cisco-autonomous-access-point.html
http://downloads.avaya.com/css/P8/documents/100041614
Thanks,
Scott
Help out other by using the rating system and marking answered questions as "Answered" -
Cisco aironet 1310 Outdoor access point
I am looking at outdoor access points, I want to stick with Cisco aironet, we currently have 6 of them that are 6 years old and running great, one has had a problem because of humidity, dried it out and relocated and we are good again.
I was looking at the Aironet 1310 Outdoor access point, but I can't find much information on it. I am looking to see how many SSIDs can be setup, we currently have 2 one private, and one public, this is done with VLANS. I am also looking at finding out about the power injector, it converts to coaxial cable, it has 2 RJ-45 and 2 Coaxial, does this mean if we get 2 access points, then I only need 1 power injector?
Thanks for any help you can give.Rusty:
AP supports up to 16 SSIDs to be configured.
Multiple SSIDs with VLANs configuration is done almost the same way you do with current Aironet APs.
see here: http://tiny.cc/0qwnkw
You also need one power injector per AP. Each AP should use it's own power injector.
The two coaxial output in the power injector both are used to be connected to the AP (see below image).
The RJ-45 connectors in the power injector one of them is for Console connectivity and the other for network ethernet connectivity.
Check here: http://tiny.cc/7gxnkw
HTH
Amjad
Rating useful replies is more useful than saying "Thank you"
Maybe you are looking for
-
I can't get Previews to work in Aperture
Hi all, I have some projects within Aperture where the previews are fine. However, for one project, I am unable to get the Previews to work (or be seen by other iLife apps). Here's what I have done so far: 1. Select my CHINA project 2. Ctrl-click and
-
Oracle Help search feature doesn't work with RoboHelp generated output
I am using RoboHelp HTML, Version 10 on Windows 7. I am able to generate Oracle Help output and integrate it with my Java application. When I do this, the Content and Index tabs work fine, but the Search feature does not. Regardless of what search
-
Hi All, There are few Items which are maintained in our DB as Fixed Assets, and now we want to use the same Item as Inventory also. So How do we maintain this. Below is the example of an Item with the senareo. Item: Wire, Fixed asset and
-
when i start itune than error shows this ipod cannot be use because the required software not install
-
Hi, We recently did a copy of a standard IDES XI system and ran some configuration scripts (provided) in the target system. Subsequent to that, we are facing the following related problems. Any help is welcome - When we run SLDCHECK, we get the follo