Wireless users facing issue range issue between two ssid

Hi
It has been observed users aren’t able to be connect to CORP SSID however they are able to connect the GUEST SSID at the same time. Incase user is moved more towards the AP then he is able to connect to CORP SSID.
Also observed that CORP SSID is showing less signal as compared to guest SSID at same location.
Please help.
Thanks
Puneet

Punnet,
Its not about the number of clients on that ap at the moment, though you are right recommendations are of about 24 clients on indoor lap platforms provided RF looks good, otherwise i have seen plannings with 16 per lap.
I think the question George is asking is what is the power level your client is transmitting at and what is the power level of your lap that is in question here?
Default transmit power on lap is 20dbm, 100 mw to give you the actual power value.
Usually clients/ machines transmit at 30mw.
My Questions:
- Which radio does this client connect to, 802.11b/g/n or a/n?
- What is the distance between lap and client when it fails to connect?
- What is the power level for the radio client connects to on that lap? (1 being max and 6 being lowest)
- Do you have lower data rates of 1 and 2 Mbps enabled on wlc?
- If yes can we try disabling them, this will improve capacity though at the cost of reduced service area for that lap.
Regards
Sahil

Similar Messages

OBIEE 11G - Issue passing parameters between two reports

Hi folks,
I am struggling to pass parameters between two reports in OBIEE 11G.
My first report contains the following columns: Rolling Year Type (VCHAR), Year(VCHAR), Month(VCHAR), Cost(Double).
My second report contains the following columns: Rolling Year Type(VCHAR), Year(VCHAR), Month(VCHAR), Category(VCHAR), Cost(Double).
My requirement is to pass the Rolling Year Type, Year and Month values from report 1 to report 2.
On the Month column properties of report 1, I have created an Action Link called 'Drill to Category'. I have clicked on 'Navigate to BI Content' and selected Report 2.
Then on Report 2, I have included three filters: Rolling Year Type is prompted, Year is prompted, Month is promted.
When I run the report I always get the following error:
The specified criteria didn't result in any data. This is often caused by applying filters and/or selections that are too restrictive or that contain incorrect values. Please check your Analysis Filters and try again. The filters currently being applied are shown below.
When I check the cursor cache, the filter values are correct. Does anybody have any idea why Report 2 does not display?
When I remove the Month filter, the report works correctly.
I have since changed the third filter to be Month No and although Report 2 does display, it does not pick up the filter on the Month No.
I initially thought this may have been a caching issue and so I have disabled BI Server Cache but this does not fix my problem.
This was never an issue on OBIEE 10G as I found it very easy to navigate between two requests.
Has anyone else experienced problems with passing parameters between two request in 11G?
Any help appreciated.
Thanks
Gavin

Hi,
I once tried this kind of requirement(with dashboard prompts though) and hit at similar issue. I later found out that the problem is with the space in the parameter values. Can you please let me know, if the same is the case with you?
Suppose the parameter passed is "Jan 2010", but the report on the destination takes the value as "Jan" & "2010". Yes, it kind of split the parameter value to two based on space. I think we can notice the filters the destination report got, by enabling filter view.
In this case, since you pass only value at a time, could you try placing the parameter value anyway in double quotes? I think the Server then will understand it as one value.
Thank you,
Dhar

Wireless users facing frequent connection and disconnection

Hi,
I am running 5508 controller with version 7.0 and 1141 access points.. I am facing a problem on user connectivity.
Wireless Users are getting frequent connection and disconnection. These users are not getting connected to the access point nearby although this access point is up and running. I ahve tried reducing the power level, configured the AP after resetting it. But nothing helps.
Has anybosy faced this issue ? May i know what could be the reason for this??

wat does the logs say?? msg logs and trap logs??
Run the debug on the client "debug client and paste it here
Regards
Surendra

Date range: relation between two datepicker.

Hi,
I would change/update start date on the second datepicker when the user selected the date on the first datepicker.
How can I manage it?
Thanks.

I did an error!
It works!
/* DatePicker */
private void fromDatePicker_SelectedDateChanged(object sender, SelectionChangedEventArgs e)
var fromPicker = sender as DatePicker;
DateTime? data = fromPicker.SelectedDate;
if (data != null)
toDatePicker.SelectedDate = data.Value.AddDays(1);
toDatePicker.DisplayDateStart = data.Value.AddDays(1);

Communication between Two WebLogic instances on the same machine

Hi,
We're having a problem with communication between two copies of Weblogic on
the same machine. They are configured with seperate ports (regular and SSL).
Independantly, they run fine. I can access EJBs running on either of them.
The problem is that a bean in one of them has code which attempts to access
an EJB on the other one. The procude fails when trying to obtain the initial
context. This same code works if compilied independantly of WebLogic on the
same machine.
Are there any known issues regards communication between two running
instances of Weblogic on the same machine?
Thanks in advance,
Randy Yarger
marchFIRST
[email protected]

Thanks for the prompt reply.
There is one IP address (internal address 10.227.1.34) one the machine. WLS1
is set up at ports 7001 and 5133. WLS2 is setup at ports 7004 and 7005.
When WLS1 attempts to obtain a context to WLS2 with the URL
t3://10.227.1.34:7004/ it pauses for a long period of time. Running truss
on the both WLS processes shows communication occuring between the two
followed by long periods of silence. Finally WLS2 spits out the error
ConnectionException[7001,7001,5133,5133,7001,7001] (paraphrased, I can get
the entire error if it would help).
After another long pause, WLS1 quits trying with the error 'Server
10.227.1.34:7004 not found' (again paraphrased).
Among the things we've tried:
* Changing the URL from the IP to 127.0.0.1
* Enabling/disabling SSL on either or both WLSs.
* Changing the server name in WLS2's copy of weblogic.properties from
'myserver' to 'myserver2' (previously they were both 'myserver')
* Upgrading WLS2 to 5.1.0sp5 (Tried upgrading WLS1, but was getting class
not found errors and quit because that WLS is being used by other people)
This is a Solaris server. WLS1 is running 5.1.0 and WLS2 is running 5.1.0sp5
Any suggestions would be appreciated.
Best,
Randy Yarger
marchFIRST
[email protected]
"Michael Girdley" <[email protected]> wrote in message
news:[email protected]...
>
>
There should not be. What is your network configuration? Are they on
separate IP addresses?
Thanks,
Michael
Michael Girdley
BEA Systems Inc
"Randy Jay Yarger" <[email protected]> wrote in message
news:[email protected]...
Hi,
We're having a problem with communication between two copies of Weblogicon
the same machine. They are configured with seperate ports (regular andSSL).
Independantly, they run fine. I can access EJBs running on either of
them.
The problem is that a bean in one of them has code which attempts toaccess
an EJB on the other one. The procude fails when trying to obtain theinitial
context. This same code works if compilied independantly of WebLogic onthe
same machine.
Are there any known issues regards communication between two running
instances of Weblogic on the same machine?
Thanks in advance,
Randy Yarger
marchFIRST
[email protected]

How to switch between two query in Web templete.

Hi all,
Here i am facing problem to switch between two query in web template by using one 'table' web item. is there any way to use hyperlink 'SAP_BW_URL' and we can switch to query. here i am using these HTML code..
<table><tr><td class="SAPBEXBtnStdBorder" cellspacing="0" cellpadding="0" border="0"><tr><td>
<table><tr><td class="sapbexbtnstd" ><A href="<SAP_BW_URL cmd='reset_item' item='table_data' query_ID='ZSD_ZSD_M01_Q20' apply_cmd_on_target= "X">" >Switch to other query</A></td></tr></table>
but i am not getting correct functionality.
please help me to solve this problem.
I know the best way to say thanks in SDN.
thanks
Kiran Patel

Kiran,
Use the web api reset_data_provider as links or in select option in HTML.
   Onchange event of this select option should call JAVASCRIPT method and
   this in turn resets the current dataprovider to your concerned one.
   How to change graphs:
   The graph item has the default data provider:
   <object>
         <param name="OWNER" value="SAP_BW"/>
         <param name="CMD" value="GET_ITEM"/>
         <param name="NAME" value="CHART_1"/>
         <param name="ITEM_CLASS" value="CL_RSR_WWW_ITEM_CHART"/>
         <param name="DATA_PROVIDER" value="DATAPROVIDER_1"/>
         <param name="TMP_CHART_DATA_HANDLE" value="IIP_49MOXB0UVNOMM6JOZMZU7QO21"/>
         ITEM:            CHART_1
   </object>
So if you change the DATAPROVIDER_1 using RESET_DATA_PROVIDER to your concerned DP, this changes chart as well !!
   Please use this method and refer to sample code for Onchange Event on SELECT OPTION:
<HTML>
<HEAD>
<script>
function callDP() {
     if(document.forms[0].dp.value == "1") {
        //form your URL here..
       url = SAP_BW_URL_Get() + "&CMD=RESET_DATA_PROVIDER&DATA_PROVIDER_1=..&...";
        SAPBWOpenURL(url);
        //or docuemtn.location.href = url..
        //etc..
</script>
</HEAD>
<BODY>
<form>
<select name="dp" onChange="javascript:callDP();">
<option value="1">1</option>
<option value="2">2</option>
</select>
</form>
</BODY>
</HTML>
HOPE THIS HELPS !!!

ADF BC: Choosing between two identical DB schemas on application startup

Hi,
We want to provide users with capability to choose between two identical db schema.
Anu idea how to do this ?

Cvele wrote:
Thanks a lot ! My pleasure.
One question: datasource name entered by the user (on the login form) is a JDBCDataSource property value for the Application module Configuration (which connect trough JDBC DataSource), correct ?Yes.
If so, then, we still must define two different sets of App Module Configurations, one for each DB schema, correct ?No. I'm not suggesting that you implement your UI like the demo that I forwarded. It might not be appropriate for your user to type in the datasource name, but the same code would be required to make the datasource name change work. Rather than getting the datasource name from the HTTPRequest and setting on the session where the custom sesison cookie impl and env info provider access you, for your solution that datasource value might come from some other place that the end-user doesn't directly type in.
Otherwise:
1. we cannot have two different datasource names, correct ?The example I forwarded should allow you to enter different JNDI names, so those would be different datasources.
2. in case of one Configuration – what is a way to define (at deployment time) username/password for each of those two schemas ? Is this correct ?The username/password information is encapsulated inside the Java EE container when you define the datasource. The application doesn't know that information and doesn't have to provide it when you are using a JDBC datasource by JNDI name.
On the other hand, what confuses me, is a fact that you say:
“You wouldn't use different configurations” And really, you example attached to me have just one App module Configuration (datasource name = jdbc/scottDS), which connect through dataSource.
Wondering what a user can enter as datasource name, except jdbc/scottDS ?I forget whether in my example I configured another datasource, but the user could enter the name of any available JNDI name for the datasource on the Java EE container.
Again, I don't suggest necessarily that you let the end-user type it in, that was just how I built the demo since I quickly evolved it from the other dynamic credentials demo that accepted the username and password from the end-user.

A homepage where I can toggle between two languages?

How can I create a homepage where I give the user the opportunity to toggle between two languages?
I what to have to differences flags in the corner, so when you press on one flag it switch to another languages.

Hi Jan,
You can to create different pages for different languages. You can place the flag on the home page and link them to the desired language page.
Regards,
Aish

N5902 wireless range issues

I bought a Lenovo wireless keyboard N5902 with backlit.
It has just arrived. Unfortunately, keyboard is not working properly: it's range is between 2-4 feet, which is way too low. I was trying to call customer service (8669684465) but noone was picking up about 11EST. What number should I reach to get customer support? Is this common issue with the keyboard?

Try using a USB cable, and repositioning the dongle. My HTPC was close to the floor, and my cursor was very erratic like yours. I moved the dongle to about 5 ft. above the floor, and it fixed the cursor movement. Try different locations.

Getting S.M.A.R.T. when trying to install Mountain lion. Hard drive works pretty well. I understand that many users have been facing the same issue. Has apple patched it yet?

I'm getting S.M.A.R.T. error when trying to install Mountain lion. Hard drive works pretty well despite the Failing status. I understand that many users have been facing the same issue. My hard drive was/is working perfectly. Has Apple patched it yet?
Has someone found a solution which is not replacing the hard drive which works just fine? Or Is anyone aware of a procedure that can force the installation despite the S.M.A.R.T error? Below details of my hard drive
Thanks
ST31******ASQ:
Capacity:          1 TB (1,000,204,886,016 bytes)
Model:          ST31000528ASQ
Revision:          AP24
Serial Number:                      6V***5JR
Native Command Queuing:          Yes
Queue Depth:          32
Removable Media:          No
Detachable Drive:          No
BSD Name:          disk0
Rotational Rate:          7200
Medium Type:          Rotational
Partition Map Type:          GPT (GUID Partition Table)
S.M.A.R.T. status:          Failing
<Edited By Host>

If you haven't done so, run Disk Utility /Applications/Utilities
to run a live verification.
The drive may be ok at the moment, but that's not to say the drive may fail at anytime.
Hopefully you have all your important data backed up just in case.

Month filter between two ranges based on user response inIDT

Hi,
I am working on SAP BO4.0.I have a requirement of creating a month filter on a date which will be between two ranges.The first range is the user response and the second range will be 6 months added to that user response.For eg:-If a user enters 1 as the response for month prompt then the date will be filtered between 1 and (1+6)=7.The database used is SAP HANA.
Please let me know if further clarifications are required.
Any help on this will be appreciated.
Thanks in advance.

Hi Riddhi ,
afaik this is not doable in UDT/IDT .Only thing we can make is to run the report for last month by using magic dates concept.
Check below logic if it helps.
For a requirement to run a report for fiscal year starting date to last month if nothing selected .
@Select(Time\Yr-Mth Key) between@Prompt('From Date','A','Time\Month / Year',mono,primary_key,,{'JUL 2013'}) and
(case when @Prompt('To Date','A','Time\Month / Year',mono,primary_key,,{'JAN 1999'})='JAN 1999' then to_char(add_months(sysdate,-1),'YYYYMM')
else
@Prompt('To Date','A','Time\Month / Year',mono,primary_key,,{'JAN 1999'}) end)
This is on Oracle Database.
When you run webi report
From Date : JUL 2013 (fiscal year start date)
To date : JAN 1999( without changing this you can refresh the report for last month , else it'll refresh for selected month)

A User facing a issue of "Collaboration Folder is not created"

Dear All,
A user facing an issue of collaboration folder is not created even through they have created in the SRM Potal.
Can anybody put some light on the issue as soon as possible.
Thanks,
Pranav

Hi
Please refer below URL.
cFolder settings in SRM
Thanks
Karitkeya

TS1398 I have an AT&T iPhone but only use wifi. Since I updated my phone to iOS 6.0 I cannot receive text messages from other iPhone users outside wifi range. What is the issue?

I have an AT&T iPhone but only use wifi. Since I updated my phone to iOS 6.0 I cannot receive text messages from other iPhone users outside wifi range. What is the issue?

Check Settings>General>Cellular to be sure you have Cellular Data set to On.

Cisco NAC: Issue for the Wireless Users being assigned "Un-Authenticated Role" to stop accessing the Network !!!

Hi,
I am looking for a solution to deal with the wireless NAC users being authenticating (Web Login Only) from a particular AD group. The mapped users gets into a particular role and access VLAN but un-mapped users get the default role which is "Un-Authentication Role" but also gets the same Access VLAN. So, the un-wanted users gets also the same access which is undesired.
I tried with one solution which is, i put those users into a role named as "Deny_Role" and Enable a Timer of 1 minute (least Time) on it, which seems working but i can see that user is disconnecting (session timeout) after 3 or 5 minutes. I want to limit this but again, i do not find this as an appropriate solution.
We could deal with wired users easily, bounce the port and get them again in "Unauthenticated Role" and VLAN will be "Un-Auth VLAN" with no network access or rediect them into a particular role with a specific VLAN. But, this is not valid in case of "Wireless Users".
So, I am looking for a solution to deal with the wireless users in this situation...
Please advise or give an idea.
BR,
Mubasher Sultan

Hi,
Any idea or suggestion...
BR,
Mubasher Sultan

How do I share files between two Macs on my wireless network?

I have an iMac G4 and an ibook G3 on a wireless network. I have "file sharing" activated on both computers. (Also Appletalk, which may or may not be a misguided move, but I got the idea from OSX "Help.")
When I try to get from either computer onto the other, my computer is recognized by name (another alternative is to log on as a "guest"). I'm prompted for a password. None of the passwords I use works. I've tried the administrative passwords for both computers.
How do I get beyond this hurdle to share files? I've posted elsewhere to no avail. This must be an easy one. How do you share files between two macs on one network?

Do your accounts on the machines have the same short name? It's an issue I've seen a few names.. one machine with bsmith, the other with bobsmith, but the long names for both being "Bob Smith". The login windows would confuse users because it showed their names, but because the short names didn't match, it wouldn't work.
The password you should use is the administrative one, so I don't know why you're not having luck.

Wireless users facing issue range issue between two ssid

Similar Messages

Maybe you are looking for