Wireless: wpa_supplicant failed to open config file [SOLVED]

Hi,
I'm having trouble configuring my wireless network. At the moment I'm following the guide from the wiki, I can scan for networks but when i try to connect with wpa_supplicant I get following error:
Successfully initialized wpa_supplicant
Failed to open config file '/dev/fd/63', error: No such file or directory
Failed to read or parse configuration '/dev/fd/63'.
So far I've tried to google the problem, but haven't found a solution that works. I hope you can point me in the right direction.
Additional info:
'ip link' provide following output:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: wwp0s29u1u4i6: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 02:80:37:ec:02:00 brd ff:ff:ff:ff:ff:ff
3: wlp3s0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DEFAULT group default qlen 1000
link/ether 00:24:d7:af:98:dc brd ff:ff:ff:ff:ff:ff
4: enp0s25: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP mode DEFAULT group default qlen 1000
link/ether f0:de:f1:53:66:eb brd ff:ff:ff:ff:ff:ff
And lspci:
lspci -k | grep Network
00:19.0 Ethernet controller: Intel Corporation 82579LM Gigabit Network Connection (rev 04)
03:00.0 Network controller: Intel Corporation Centrino Ultimate-N 6300 (rev 35)
And dmesg:
dmesg | grep firmware
[ 2.379351] iwlwifi 0000:03:00.0: Direct firmware load for iwlwifi-6000-6.ucode failed with error -2
[ 2.379368] iwlwifi 0000:03:00.0: Direct firmware load for iwlwifi-6000-5.ucode failed with error -2
[ 2.382114] iwlwifi 0000:03:00.0: loaded firmware version 9.221.4.1 build 25532 op_mode iwldvm
[ 8.560626] psmouse serio2: trackpoint: IBM TrackPoint firmware: 0x0e, buttons: 3/3
I guess it have something to do with the firmware, but I'm not sure, as when I googled the problem I stumbled upon a site stating that the wireless card should be supported by the kernel.
Last edited by cube2 (2015-01-07 14:00:34)

Yes it is on the same line as this:
sudo wpa_supplicant -D nl80211,wext -i wlp3s0 -c <(wpa_passphrase "SSID" "key")
systemtcl list-units
systemctl list-units
UNIT LOAD ACTIVE SUB DESCRIPTION
proc-sys-fs-binfmt_misc.automount loaded active waiting Arbitrary Executable File Formats File System Automount Point
sys-devices-pci0000:00-0000:00:01.0-0000:01:00.0-backlight-acpi_video1.device loaded active plugged /sys/devices/pci0000:00/0000:00:01.0/0000:01:00.0/backlight/acpi_video1
sys-devices-pci0000:00-0000:00:01.0-0000:01:00.0-drm-card0-card0\x2dLVDS\x2d1-nv_backlight.device loaded active plugged /sys/devices/pci0000:00/0000:00:01.0/0000:01:00.0/drm/card0/card0-LVDS-1/nv_backlight
sys-devices-pci0000:00-0000:00:02.0-backlight-acpi_video0.device loaded active plugged /sys/devices/pci0000:00/0000:00:02.0/backlight/acpi_video0
sys-devices-pci0000:00-0000:00:02.0-drm-card1-card1\x2dLVDS\x2d2-intel_backlight.device loaded active plugged /sys/devices/pci0000:00/0000:00:02.0/drm/card1/card1-LVDS-2/intel_backlight
sys-devices-pci0000:00-0000:00:16.3-tty-ttyS0.device loaded active plugged 6 Series/C200 Series Chipset Family KT Controller
sys-devices-pci0000:00-0000:00:19.0-net-enp0s25.device loaded active plugged 82579LM Gigabit Network Connection
sys-devices-pci0000:00-0000:00:1a.0-usb3-3\x2d1-3\x2d1.4-3\x2d1.4:1.0-bluetooth-hci0-rfkill2.device loaded active plugged /sys/devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.4/3-1.4:1.0/bluetooth/hci0/rfkill2
sys-devices-pci0000:00-0000:00:1a.0-usb3-3\x2d1-3\x2d1.4-3\x2d1.4:1.0-bluetooth-hci0.device loaded active plugged /sys/devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1.4/3-1.4:1.0/bluetooth/hci0
sys-devices-pci0000:00-0000:00:1b.0-sound-card0.device loaded active plugged 6 Series/C200 Series Chipset Family High Definition Audio Controller
sys-devices-pci0000:00-0000:00:1c.1-0000:03:00.0-ieee80211-phy0-rfkill3.device loaded active plugged /sys/devices/pci0000:00/0000:00:1c.1/0000:03:00.0/ieee80211/phy0/rfkill3
sys-devices-pci0000:00-0000:00:1c.1-0000:03:00.0-net-wlp3s0.device loaded active plugged Centrino Ultimate-N 6300 (3x3 AGN)
sys-devices-pci0000:00-0000:00:1d.0-usb4-4\x2d1-4\x2d1.4-4\x2d1.4:1.1-tty-ttyACM0.device loaded active plugged F5521gw
sys-devices-pci0000:00-0000:00:1d.0-usb4-4\x2d1-4\x2d1.4-4\x2d1.4:1.3-tty-ttyACM1.device loaded active plugged F5521gw
sys-devices-pci0000:00-0000:00:1d.0-usb4-4\x2d1-4\x2d1.4-4\x2d1.4:1.6-net-wwp0s29u1u4i6.device loaded active plugged F5521gw
sys-devices-pci0000:00-0000:00:1d.0-usb4-4\x2d1-4\x2d1.4-4\x2d1.4:1.9-tty-ttyACM2.device loaded active plugged F5521gw
sys-devices-pci0000:00-0000:00:1f.2-ata1-host0-target0:0:0-0:0:0:0-block-sda-sda1.device loaded active plugged INTEL_SSDSA2M160G2LE 1
sys-devices-pci0000:00-0000:00:1f.2-ata1-host0-target0:0:0-0:0:0:0-block-sda-sda2.device loaded active plugged INTEL_SSDSA2M160G2LE 2
sys-devices-pci0000:00-0000:00:1f.2-ata1-host0-target0:0:0-0:0:0:0-block-sda.device loaded active plugged INTEL_SSDSA2M160G2LE
sys-devices-pci0000:00-0000:00:1f.2-ata2-host1-target1:0:0-1:0:0:0-block-sr0.device loaded active plugged MATSHITADVD-RAM_UJ8A2
sys-devices-platform-serial8250-tty-ttyS1.device loaded active plugged /sys/devices/platform/serial8250/tty/ttyS1
sys-devices-platform-serial8250-tty-ttyS2.device loaded active plugged /sys/devices/platform/serial8250/tty/ttyS2
sys-devices-platform-serial8250-tty-ttyS3.device loaded active plugged /sys/devices/platform/serial8250/tty/ttyS3
sys-devices-platform-thinkpad_acpi-rfkill-rfkill0.device loaded active plugged /sys/devices/platform/thinkpad_acpi/rfkill/rfkill0
sys-devices-platform-thinkpad_acpi-rfkill-rfkill1.device loaded active plugged /sys/devices/platform/thinkpad_acpi/rfkill/rfkill1
sys-devices-platform-thinkpad_acpi-sound-card29.device loaded active plugged /sys/devices/platform/thinkpad_acpi/sound/card29
sys-module-configfs.device loaded active plugged /sys/module/configfs
sys-subsystem-bluetooth-devices-hci0.device loaded active plugged /sys/subsystem/bluetooth/devices/hci0
sys-subsystem-net-devices-enp0s25.device loaded active plugged 82579LM Gigabit Network Connection
sys-subsystem-net-devices-wlp3s0.device loaded active plugged Centrino Ultimate-N 6300 (3x3 AGN)
sys-subsystem-net-devices-wwp0s29u1u4i6.device loaded active plugged F5521gw
-.mount loaded active mounted /
dev-hugepages.mount loaded active mounted Huge Pages File System
dev-mqueue.mount loaded active mounted POSIX Message Queue File System
home.mount loaded active mounted /home
run-user-1000.mount loaded active mounted /run/user/1000
sys-kernel-config.mount loaded active mounted Configuration File System
sys-kernel-debug.mount loaded active mounted Debug File System
tmp.mount loaded active mounted Temporary Directory
systemd-ask-password-console.path loaded active waiting Dispatch Password Requests to Console Directory Watch
systemd-ask-password-wall.path loaded active waiting Forward Password Requests to Wall Directory Watch
session-c1.scope loaded active running Session c1 of user jakob
dbus.service loaded active running D-Bus System Message Bus
[email protected] loaded active running dhcpcd on enp0s25
[email protected] loaded active running Getty on tty1
kmod-static-nodes.service loaded active exited Create list of required static device nodes for the current kernel
systemd-backlight@backlight:acpi_video0.service loaded active exited Load/Save Screen Backlight Brightness of backlight:acpi_video0
systemd-backlight@backlight:acpi_video1.service loaded active exited Load/Save Screen Backlight Brightness of backlight:acpi_video1
systemd-backlight@backlight:intel_backlight.service loaded active exited Load/Save Screen Backlight Brightness of backlight:intel_backlight
systemd-backlight@backlight:nv_backlight.service loaded active exited Load/Save Screen Backlight Brightness of backlight:nv_backlight
systemd-fsck@dev-disk-by\x2duuid-69c2b129\x2dd95a\x2d48f7\x2d84de\x2d058ba5f97b42.service loaded active exited File System Check on /dev/disk/by-uuid/69c2b129-d95a-48f7-84de-058ba5f97b42
systemd-journal-flush.service loaded active exited Trigger Flushing of Journal to Persistent Storage
systemd-journald.service loaded active running Journal Service
systemd-logind.service loaded active running Login Service
systemd-random-seed.service loaded active exited Load/Save Random Seed
systemd-remount-fs.service loaded active exited Remount Root and Kernel File Systems
[email protected] loaded active exited Load/Save RF Kill Switch Status of rfkill0
[email protected] loaded active exited Load/Save RF Kill Switch Status of rfkill1
[email protected] loaded active exited Load/Save RF Kill Switch Status of rfkill2
[email protected] loaded active exited Load/Save RF Kill Switch Status of rfkill3
systemd-sysctl.service loaded active exited Apply Kernel Variables
systemd-tmpfiles-setup-dev.service loaded active exited Create Static Device Nodes in /dev
systemd-tmpfiles-setup.service loaded active exited Create Volatile Files and Directories
systemd-udev-trigger.service loaded active exited udev Coldplug all Devices
systemd-udevd.service loaded active running udev Kernel Device Manager
pstree
systemd─┬─chromium─┬─chrome-sandbox───chromium─┬─chrome-sandbox───nacl_helper
│ │ └─chromium─┬─chromium─┬─2*[{Blink GC Sweepe}]
│ │ │ ├─2*[{Blink Heap Mark}]
│ │ │ ├─{Chrome_ChildIOT}
│ │ │ ├─{Compositor}
│ │ │ ├─{HTMLParserThrea}
│ │ │ ├─{OptimizingCompi}
│ │ │ ├─{WorkerPool/662}
│ │ │ └─{WorkerPool/663}
│ │ ├─chromium─┬─2*[{Blink GC Sweepe}]
│ │ │ ├─2*[{Blink Heap Mark}]
│ │ │ ├─{Chrome_ChildIOT}
│ │ │ ├─{Compositor}
│ │ │ ├─{HTMLParserThrea}
│ │ │ └─{OptimizingCompi}
│ │ ├─12*[chromium─┬─2*[{Blink GC Sweepe}]]
│ │ │ ├─2*[{Blink Heap Mark}]]
│ │ │ ├─{Chrome_ChildIOT}]
│ │ │ ├─{CompositorRaste}]
│ │ │ ├─{Compositor}]
│ │ │ ├─{HTMLParserThrea}]
│ │ │ └─{OptimizingCompi}]
│ │ ├─chromium─┬─2*[{Blink GC Sweepe}]
│ │ │ ├─2*[{Blink Heap Mark}]
│ │ │ ├─{Chrome_ChildIOT}
│ │ │ ├─{CompositorRaste}
│ │ │ ├─{Compositor}
│ │ │ ├─{HTMLParserThrea}
│ │ │ ├─{OptimizingCompi}
│ │ │ ├─{WorkerPool/155}
│ │ │ └─{WorkerPool/156}
│ │ ├─chromium─┬─2*[{Blink GC Sweepe}]
│ │ │ ├─2*[{Blink Heap Mark}]
│ │ │ ├─{Chrome_ChildIOT}
│ │ │ ├─{CompositorRaste}
│ │ │ ├─{Compositor}
│ │ │ ├─{HTMLParserThrea}
│ │ │ ├─{OptimizingCompi}
│ │ │ ├─{WorkerPool/666}
│ │ │ └─{WorkerPool/667}
│ │ └─chromium─┬─{AudioOutputDevi}
│ │ ├─2*[{Blink GC Sweepe}]
│ │ ├─2*[{Blink Heap Mark}]
│ │ ├─{Chrome_ChildIOT}
│ │ ├─{CompositorRaste}
│ │ ├─{Compositor}
│ │ ├─{FFmpegDemuxer}
│ │ ├─{HTMLParserThrea}
│ │ ├─{Media}
│ │ ├─{OptimizingCompi}
│ │ ├─{WorkerPool/688}
│ │ └─{WorkerPool/693}
│ ├─chromium─┬─chromium
│ │ ├─{Chrome_ChildIOT}
│ │ └─{Watchdog}
│ ├─{AudioThread}
│ ├─{Blink GC Sweepe}
│ ├─2*[{Blink Heap Mark}]
│ ├─3*[{BrowserBlocking}]
│ ├─{BrowserWatchdog}
│ ├─3*[{CachePoolWorker}]
│ ├─{Chrome_CacheThr}
│ ├─{Chrome_DBThread}
│ ├─{Chrome_FileThre}
│ ├─{Chrome_FileUser}
│ ├─{Chrome_HistoryT}
│ ├─{Chrome_IOThread}
│ ├─{Chrome_ProcessL}
│ ├─{Chrome_SafeBrow}
│ ├─{Chrome_SyncThre}
│ ├─{CrShutdownDetec}
│ ├─{IndexedDB}
│ ├─{LevelDBEnv.IDB}
│ ├─{LevelDBEnv}
│ ├─{NSS SSL ThreadW}
│ ├─{NetworkChangeNo}
│ ├─{OptimizingCompi}
│ ├─2*[{Proxy resolver}]
│ ├─{WorkerPool/1890}
│ ├─{WorkerPool/1936}
│ ├─{chromium}
│ ├─{extension_crash}
│ ├─{gpu-process_cra}
│ ├─{handle-watcher-}
│ ├─{inotify_reader}
│ ├─{renderer_crash_}
│ └─{sandbox_ipc_thr}
├─2*[dbus-daemon]
├─dbus-launch
├─dhcpcd
├─login───startx───xinit─┬─Xorg.bin─┬─xf86-video-inte
│ │ └─{Xorg.bin}
│ └─awesome───{gmain}
├─systemd───(sd-pam)
├─systemd-journal
├─systemd-logind
├─systemd-udevd
├─xterm───bash───pstree
└─xterm───bash

Similar Messages

  • Failed to open package file due to error 0x800C0006 "The system cannot locate the file in C# code.

    Hi, Am facing issue when I try to run SSIS package via C# code, I have given full access to all the folder in which the package is available.
    In the below line am getting error,
    using Microsoft.SqlServer.DTS.Runtime;
    Application app=new Application();
    Package package=null;
    package=app.LoadPackage("PackageFullPath",null) --error line
    Failed to open package file "C:\SSIS\Package.dtsx" due to error 0x800C0006 "The system
    cannot locate the object specified.".  This occurs when loading a
    package and the file cannot be opened or loaded correctly into the XML document

    Are you trying to run this code from job or something? Check if account executing the package has access to the path. Also check if path value passed is correct. If its a remote system path pass it in UNC format (ie //machine/...)
    Please Mark This As Answer if it solved your issue
    Please Vote This As Helpful if it helps to solve your issue
    Visakh
    My MSDN Page
    My Personal Blog
    My Facebook Page

  • "Failed to open package file ..." when modifying job step on remote server

    I have SSIS package setup on a remote SQL Server to run on schedule via SQL Server Agent. It was setup initially by remote desktop-ing to the server and connecting to it via SSMS running on the same machine where SQL Server is running. Package source is
    "File System" and absolute path is specified (D:\Folder1\Package1.dtsx). There is just one step in the job - to run SSIS package. Everything works as it should.
    Now I want to modify this job - change number of retry on failure attempts. I can successfully connect to this SQL Server instance via SSMS from my developer workstation. I can then go to "Advanced Settings" for this job step and change "Retry attempts"
    to some other number. However, when I press "OK" I get this error message:
    TITLE: SSIS Execution Properties
    Failed to open package file "D:\Folder1\Package1.dtsx" due to error 0x80070003 "The system cannot find the path specified.".  This happens when loading a package and the file cannot be opened or loaded correctly into the XML document. This can
    be the result of either providing an incorrect file name was specified when calling LoadPackage or the XML file was specified and has an incorrect format.
     ({105912C7-6345-42B4-99B4-58566291867B})
    ADDITIONAL INFORMATION:
    Failed to open package file "D:\Folder1\Package1.dtsx" due to error 0x80070003 "The system cannot find the path specified.".  This happens when loading a package and the file cannot be opened or loaded correctly into the XML document. This can
    be the result of either providing an incorrect file name was specified when calling LoadPackage or the XML file was specified and has an incorrect format.
     ({105912C7-6345-42B4-99B4-58566291867B})
    Interestingly enough, in spite of this error message the number of retries is successfully changed.
    I understand it happens because SSMS tries to locate package on my local hard drive and the same folder doesn't exist on my development PC. It still doesn't make sense to me. Does SSMS not know I am accessing remote server? How come I don't get any errors
    when I just execute this job via SSMS when SSMS runs on my development PC?

    Hi, Am facing same issue, but I am trying run SSIS package via C# code, I have given full access to all the folder in which the package is available.
    In the below line am getting error,
    using Microsoft.SqlServer.DTS.Runtime;
    Application app=new Application();
    Package package=null;
    package=app.LoadPackage("PackageFullPath",null) --error line
    Failed to open package file "C:\SSIS\Package.dtsx" due to error 0x800C0006 "The system
    cannot locate the object specified.".  This occurs when loading a
    package and the file cannot be opened or loaded correctly into the XML document
    full access to which account? also trying to run from where? In the same machine where package resides?
    Please Mark This As Answer if it solved your issue
    Please Vote This As Helpful if it helps to solve your issue
    Visakh
    My MSDN Page
    My Personal Blog
    My Facebook Page

  • "Extraction Failed: Cannot Open Output File" error message when installing new drivers

    Hello, I'm trying to install new drivers for my HP Photosmart C4385 Printer.  I downloaded the full feature drivers for Windows XP 32-bit, and when I start to install (extract), I get the error message:
    Extraction Failed
    Cannot Open Output File
    And the process closes.  It happens at about 85% extraction every time.
    Any idea why?  I called HP but since it is out of warranty they wanted money, which I think as absolutely ridiculous - won't even give me basic support??  Poor, poor customer service.
    This question was solved.
    View Solution.

    Hi,
    If you haven't still got the  Full Feature software installer, download it from the link below and save it to your Desktop.  If you already have it, place it on your Desktop.
    ftp://ftp.hp.com/pub/softlib/software10/COL20274/mp-53147-4/100_228_PS_AIO_02_Full_USW_enu_NB.exe
    Make sure the Printer is disconnected from your PC.
    Download and install 7-ZIP.  Once installed, right click on the software installer for your printer, select 7-Zip and choose extract files, then click Ok.
    Open the newly extracted folder and double click the setup application to start the installation ( the setup application will probably have the same icon as the original software installer you downloaded ).  Connect the printer to your PC when the software asks.
    Hope this helps.
    Best wishes,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • Libre ~ Error 2038 "failed to open the file"

    Good morning.
    I have a Libre-eBook reader Pro.
    I have downloaded and synced from Kobo to my Libre with no problems.
    But when I try to download ebooks from the public library they download and open in Digital Editions just fine.  I drag and drop them into the bookshelf marked Libre-eBook Reader Pro.
    They show up when I turn on my ebook, but when I try to open them I get the 'failed to open the file'.
    I was also getting the Error 2038 in Digital Editions when I did the drag and drop thing.  I read through the forum and went through the steps recommended for the Nook ~ deleting the digital editions folder on my ebook and having Adobe reauthorize it.  I no longer get the 2038 error message in Adobe, but I am still unable to open the books from the library.
    I have tried deleting the books from ereader and ADE and redownloading from the Library.  Didn't help.
    Any other suggestions?
    Thanks.
    Heather

    Hi Ambs101010,
    Based on my research, the error can be caused by that the machine.config file is incorrect or corrupted. Please use the following steps to troubleshoot the issue and check if the error still occurs.
    1. Open the machine.config in Visual Studio and check if there is any syntax errors. If syntax errors exist, modify the machine.config file directly. For more details, please review this similar
    thread.
    2. If the error still persists, please follow the steps to replace the machine.config file. Another alternative method is to replace the current machine.config with the machine.config file from another computer.
          a.  Go to the folder C:\windows\Microsoft.NET\Framework\v2.0.50727\CONFIG
          b.  Rename the file machine.config to machine.config.old
          c.  Make a copy of the file machine.config.default and rename the copy to be machine.config
          d.  If your Operating System is 64-bit, go to the folder C:\windows\Microsoft.NET\Framework64\v2.0.50727\CONFIG and repeat the above steps
          e.  Reboot your computer
    Thanks,
    Lydia Zhang

  • "Unable to open config file" Error when starting tomcat

    hi all,
    Here is the output from two of the log files when I start tomcat4 on my linux box. I have configured the mod_jk on the tomcat side.
    From the output of the second log file, it seems that the ajp13 worker I defined was started successfully. What I don't understand is the following:
    1) In catalina.out, where des the line 'Unable to open config file' come from? Which config file?
    2) Tomcat4 is supposed to generate a mod_jk.conf automatically, but I don't see any file generated in 'conf/auto/'.
    Content of 'catalina.out'
    Unable to open config file
    Starting service Tomcat-Standalone
    Apache Tomcat/4.0.4
    Unable to open config file
    Starting service Tomcat-Apache
    Apache Tomcat/4.0.4content of 'catalina_log.2002-08-16.txt'
    2002-08-16 01:05:22 HttpConnector Opening server socket on all host IP addresses
    2002-08-16 01:05:28 Ajp13Connector[8009] Opening server socket on all host IP addresses
    2002-08-16 01:05:28 Ajp13Connector[8009] Starting background thread
    2002-08-16 01:05:29 Ajp13Processor[8009][0] Starting background thread
    2002-08-16 01:05:29 Ajp13Processor[8009][1] Starting background thread
    2002-08-16 01:05:29 Ajp13Processor[8009][2] Starting background thread
    2002-08-16 01:05:29 Ajp13Processor[8009][3] Starting background thread
    2002-08-16 01:05:29 Ajp13Processor[8009][4] Starting background thread

    I have all those files too.
    I think the 'config file' mentioned in the error log is the mod_jk.conf.
    On Jason Hunter's tomcat4 guide, it says don't use the tomcat4 RPM to installed. What is the difference bettween the RPM version and the tar.gz version? The only difference I can think of is that in the RPM version, the conf directory is in the 'etc/tomcat4/conf'. Could it be the reason that tomcat4 cannot read the config file? But it has no problem reading the server.xml though.

  • SP2-0310: Failed to open the file "coreins.sql"

    Hi, when i try to install apex 3.0... on oraclexe , in the file install****.log show this error SP2-0310: Failed to open the file "coreins.sql"

    You will find the answer to your problem in this forum..
    Database Installation

  • Pls Help!-'Failed to open the file'

    what do you do when an error 'failed to open the file' shows
    up when you try to open something...?
    i'm pretty sure that i am using the same version of flash as
    the one i used before to create this file.. but just on a different
    mac.
    please
    help!!!!　(ﾉ△･｡)

    yumibobcat wrote:
    > what do you do when an error 'failed to open the file'
    shows up when you try to
    > open something...?
    > i'm pretty sure that i am using the same version of
    flash as the one i used
    > before to create this file.. but just on a different
    mac.
    > please help!!!!?(????)
    >
    If you are using the same version the file was made in then
    the only thing
    left which give such error is a corrupted FLA. Beyond
    recovery once fail to
    open.
    Best Regards
    Urami
    "Never play Leap-Frog with a Unicorn."
    <urami>
    If you want to mail me - DO NOT LAUGH AT MY ADDRESS
    </urami>

  • After Effects CS3 error: file not found -43 and TIFFIO failed to open the file

    Hello
    I am experiencing a problem with AE CS3.
    I have several TIFF sequences (with alphas) that are giving me a headache. When I import them into AE, I get an "AEGP Plugin TIFFIO: Failed to open the file" error.
    I researched the forums and found that this could be related to odd formatting of the source media (my TIFF sequence). I created these TIFFs in Maya 2008 and I have imported other sequences made with Maya into AE with no issues.
    Just to be sure, I created a Photoshop droplet that re-saved my TIFFs as Photoshop TIFFs with the same names.
    I re-imported the new Photoshop TIFF sequences (still with alphas) into AE CS3, and I get the same error.
    Any ideas? I don't know what to do next.
    Thanks,
    -------------S

    Your USB drive may have had a weird character in it's name.
    AE can't read CMYK images, that is usually the problem.
    Imported images do not have to conform to any specific sizes (unless you want to go over 30,000 x 30,000 pixels.)
    - Jonas Hummelstrand
    http://generalspecialist.com/

  • 'failed to open the file'

    what do you do when an error 'failed to open the file' shows
    up when you try to open something...?
    i'm pretty sure that i am using the same version of flash as
    the one i used before to create this file.. but just on a different
    mac.
    please
    help!!!!　(ﾉ△･｡)

    You will find the answer to your problem in this forum..
    Database Installation

  • Fail to open PDF file. Error for trying to paste in object.

    So occasionaly, i will paste in a PDF into my InDesign document and this error will pop up, Fail to open PDF file.  It's not like im opening
    the file im just trying to paste it in.  I try other pdf files and the same error comes up.  Usually this error does not happen when i am pasting in
    PDF's into my document but when one error comes up, no PDF's will work.  I have to resave my file into another format and then it will work.
    What is up with these errors that happen sometimes?
    CS5 ID 7.0.3
    P.C.

    Try it again...this time click the show options check box in the place dialog.
    Bob

  • Failed to open pdf files

    Hi,
    I guess since the latest os/safari upgrade, the application has failed to open pdf files on several occasions. It's one of those files that you have to download then I guess the safari or adobe reader opens it... The beach ball keeps spinning and safari has to be force quit. I have the latest safari and adobe reader.
    Can someone please help, thanks.
    PowerBook G4 1.67GHZ   Mac OS X (10.4.6)  

    Why not let Safari/Preview handle your PDF files? Tiger offers this alternative. To do so, remove the Adobe Reader plug-in from your Internet Plug-in folder (may be in either your Main or User Library folder). When Safari encounters a PDF file, it will then automatically open the file in Safari using Previews PDF format.
    Another alternative (which includes removing the Adobe plug-in) is to use PDF Browser Plug-in. This plug-in is freeware for private use.
    iMac G5 Rev C 20" 2.5gb RAM 250 gb HD/iBook G4 1.33 ghz 1.5gb RAM 40 gb HD   Mac OS X (10.4.6)   LaCie 160gb d2 HD Canon i960 printer

  • Failed tp open .prp file while running HAL ...it says Sharing voilation ..

    Failed tp open .prp file while running HAL ...it says Sharing voilation ..
    I am running a HAL job.
    While opening .prp file it says error Sharing voilation cannot open file.
    Please help to resolve issue.

    Are you sure there are not multiple instances of the prp open, say 2 remote connections both with the file open.
    If there is a lock on the file and you are able to reboot the machine I would give that a go.
    Cheers
    John
    http://john-goodwin.blogspot.com/

  • Conf HTTP server getting error "failed to open memory file"

    Hi,all,
    Anyone has any idea what is happening here? Should the System Admin can help? or I should check my httpd.conf file?
    Thanks,
    Ken
    ====================================
    Apache > bin/apachectl configtest
    Ouch! ap_mm_create(1048576, "/oracle/app/oracle/product/10.1.3.1/OracleAS_1/Apache/Apache/logs/mm.8359") failed
    Error: MM: mm:core: failed to open memory file (Permission denied): OS: No such file or directory
    WARNING!! Direct use of apachectl within OracleAS is
    deprecated. Using apachectl in conjunction with opmn may lead
    to unexpected behavior (such as opmn automatically restarting
    OHS after it has been shutdown using apachectl). Please use
    opmnctl (located at ORACLE_HOME/opmn/bin/opmnctl) instead.
    apachectl may not be shipped with future versions of OracleAS.
    [16:15:23]
    [ebizora01 8] Apache > ls -l logs/
    total 17212
    drwxr-x--- 4 oracle dba 1536 Jun 21 11:31 .
    -rw------- 1 oracle oinstall 0 Jun 19 12:50 mm.3482.sem
    -rw------- 1 oracle oinstall 1052672 Jun 19 12:50 mm.3482.mem
    -rw------- 1 oracle oinstall 0 Jun 19 12:46 mm.3475.sem
    -rw------- 1 oracle oinstall 1052672 Jun 19 12:46 mm.3475.mem
    -rw------- 1 oracle oinstall 0 Jun 19 12:35 mm.3388.sem
    -rw------- 1 oracle oinstall 1052672 Jun 19 12:35 mm.3388.mem
    drwxr-x--- 16 oracle dba 512 Jun 19 11:05 ..
    -rw-r--r-- 1 root root 4546 Mar 26 13:11 error_log.1174910400
    -rw------- 1 root root 0 Mar 26 13:11 mod_oc4j.4395.shm.sem
    -rw------- 1 root root 1052672 Mar 26 13:11 mod_oc4j.4395.shm.mem
    -rw-r--r-- 1 root root 5 Mar 26 13:11 httpd.pid
    -rw------- 1 root root 7405568 Mar 26 13:11 dms_metrics_4390.shm.mem
    ---Sr--r-- 1 root root 0 Mar 26 13:11 dms_metrics_4390.lock
    -rw------- 1 root root 0 Mar 26 13:11 dms_metrics_4390.shm.sem
    -rw------- 1 oracle root 0 Mar 26 13:11 mm.4390.sem
    -rw------- 1 oracle root 1052672 Mar 26 13:11 mm.4390.mem
    -rw------- 1 root root 0 Mar 26 12:32 mm.3468.sem
    -rw------- 1 root root 1052672 Mar 26 12:32 mm.3468.mem
    -rw------- 1 root root 0 Mar 26 12:30 mm.3465.sem
    -rw------- 1 root root 1052672 Mar 26 12:30 mm.3465.mem
    -rw------- 1 root root 0 Mar 26 12:28 mm.3451.sem
    -rw------- 1 root root 1052672 Mar 26 12:28 mm.3451.mem
    -rw------- 1 root root 0 Mar 26 12:26 mm.3444.sem
    -rw------- 1 root root 1052672 Mar 26 12:26 mm.3444.mem
    -rw-rw---- 1 oracle dba 477791 Mar 23 08:42 access_log.1174651200
    -rw-rw---- 1 oracle dba 894031 Mar 23 08:42 error_log.1174651200
    -rwxr-x--- 1 oracle dba 4180 Mar 23 07:37 ssl_engine_log
    -rw-rw---- 1 oracle dba 476971 Mar 22 11:11 access_log.1174564800
    -rw-rw---- 1 oracle dba 890666 Mar 22 11:11 error_log.1174564800
    -rw-rw---- 1 oracle dba 478049 Mar 20 11:19 access_log.1174392000
    -rw-rw---- 1 oracle dba 895811 Mar 20 11:19 error_log.1174392000
    -rw-rw---- 1 oracle dba 478593 Mar 15 11:10 access_log.1173960000
    -rw-rw---- 1 oracle dba 895242 Mar 15 11:10 error_log.1173960000
    -rw-rw---- 1 oracle dba 478006 Mar 13 11:15 access_log.1173787200
    -rw-rw---- 1 oracle dba 894983 Mar 13 11:15 error_log.1173787200
    -rw-rw---- 1 oracle dba 1346 Mar 12 11:07 access_log.1173700800
    -rw-rw---- 1 oracle dba 395 Mar 12 11:07 error_log.1173700800
    -rw-rw---- 1 oracle dba 1288 Mar 9 16:42 access_log.1173484800
    -rwxr-x--- 1 oracle dba 790 Mar 9 16:42 error_log.1173484800
    drwxr-x--- 3 oracle dba 512 Mar 9 16:40 fastcgi
    drwxr-x--- 2 oracle dba 512 Mar 9 16:40 oracle

    my bad. my account was not oracle, so I did not have the privelleges to write to the directory.
    This is fixed after su to oracle.
    Thanks,
    Ken

  • Tried to install Firefox but an error message "Extraction failed - cannot open output file" always pops up, without a reason. Why's this happening?

    Tried to install Firefox but an error message "Extraction failed - cannot open output file" always pops up, without a reason. Why's this happening?

    Try to disable your anti-virus software temporarily to see if that makes it work.
    You may need to delete the temp folder (%TEMP%) to remove the old files.

Maybe you are looking for