Wireless Zero Configuration fails to start. (WZC)
When the computer is turned on the WZC fails to start. This wasn't a problem until two days ago. I have to use the BT Desktop Help which resolves whatever the issue is but every time I power down the problem returns. No new programs loaded. No new hardware added. Any suggestions on how to fix the problem.
It is usually cause by a 3rd party wireless manager which conflicts with Windows.
The usual culprit is the BT Wireless manager.
If you want to use Windows to manage your wireless connection, then it would be best to remove the BT one using add/remove programs.
BT Desktop Help, often causes more problems than it fixes in some cases. Again, unless you really cannot manage without it, I would advise removing it.
There are some useful help pages here, for BT Broadband customers only, on my personal website.
BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.
Similar Messages
-
Linksys Wireless Network monitor overrides Windows XP Wireless Zero Configuration
Hello all,
I am currently using the wireless router Verizon sent me and it works fine when using the Windows XP Wireless Zero Configuration tool. Previously I was using a Linksys wireless router and I have the Linksys Wireless Network monitor installed. About half the time when starting up the computer, the Linksys monitor starts up and I have to manually switch to the Windows XP Wireless Zero Configuration tool. This is very irritating and I would like to know if there is a way I can remove the Linksys Monitor and still be able to use the Linksys wireless adapter cards installed in the computer.I think I know.
#1 http://netsquirrel.com/msconfig/msconfig_xp.html
#2 Very carefully, look through the list in MSConfig.
#3 Disable the Linksys Wireless Network monitor.
Restart the computer as need be.
If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it. If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button. -
[SOLVED] Shorewall Universal configuration fails to start
I wanted to try shorewall.
I installed it with pacman:
$ pacman -Q shorewall
shorewall 4.6.1.2-1
I chose the Universal configuration, copying the corresponding files to /etc/shorewall.
When I try to start it by 'systemctl start shorewall.service', it fails with:
juin 25 17:54:24 arch64 systemd[1]: Starting Shorewall IPv4 firewall...
juin 25 17:54:24 arch64 shorewall[24056]: Compiling...
juin 25 17:54:24 arch64 shorewall[24056]: Processing /etc/shorewall/params ...
juin 25 17:54:24 arch64 shorewall[24056]: Processing /etc/shorewall/shorewall.conf...
juin 25 17:54:24 arch64 shorewall[24056]: Loading Modules...
juin 25 17:54:25 arch64 shorewall[24056]: Compiling /etc/shorewall/zones...
juin 25 17:54:25 arch64 shorewall[24056]: Compiling /etc/shorewall/interfaces...
juin 25 17:54:25 arch64 shorewall[24056]: Determining Hosts in Zones...
juin 25 17:54:25 arch64 shorewall[24056]: Locating Action Files...
juin 25 17:54:25 arch64 shorewall[24056]: Compiling /etc/shorewall/policy...
juin 25 17:54:25 arch64 shorewall[24056]: Running /etc/shorewall/initdone...
juin 25 17:54:25 arch64 shorewall[24056]: Adding rules for DHCP
juin 25 17:54:25 arch64 shorewall[24056]: Compiling TCP Flags filtering...
juin 25 17:54:25 arch64 shorewall[24056]: Compiling Kernel Route Filtering...
juin 25 17:54:25 arch64 shorewall[24056]: Compiling Martian Logging...
juin 25 17:54:25 arch64 shorewall[24056]: Compiling MAC Filtration -- Phase 1...
juin 25 17:54:25 arch64 shorewall[24056]: Compiling /etc/shorewall/rules...
juin 25 17:54:25 arch64 shorewall[24056]: Compiling /etc/shorewall/conntrack...
juin 25 17:54:25 arch64 shorewall[24056]: Compiling MAC Filtration -- Phase 2...
juin 25 17:54:25 arch64 shorewall[24056]: Applying Policies...
juin 25 17:54:25 arch64 shorewall[24056]: Compiling /usr/share/shorewall/action.Drop for chain Drop...
juin 25 17:54:25 arch64 shorewall[24056]: Compiling /usr/share/shorewall/action.Broadcast for chain Broadcast...
juin 25 17:54:25 arch64 shorewall[24056]: Generating Rule Matrix...
juin 25 17:54:25 arch64 shorewall[24056]: Optimizing Ruleset...
juin 25 17:54:25 arch64 shorewall[24056]: Can't use string ("filter") as a HASH ref while "strict refs" in use at /usr/share/shorewall/Chains.pm line 3486.
juin 25 17:54:25 arch64 shorewall[24056]: /bin/sh: /var/lib/shorewall/.start: Aucun fichier ou dossier de ce type
juin 25 17:54:25 arch64 shorewall[24056]: /bin/sh: /var/lib/shorewall/.start: Aucun fichier ou dossier de ce type
juin 25 17:54:25 arch64 systemd[1]: shorewall.service: main process exited, code=exited, status=127/n/a
juin 25 17:54:25 arch64 systemd[1]: Failed to start Shorewall IPv4 firewall.
juin 25 17:54:25 arch64 systemd[1]: Unit shorewall.service entered failed state.
I am unable to understand and fix this issue.
Can someone help me please?
Edit: changed the title of the thread.
Last edited by berbae (2014-08-22 12:33:58)Since shorewall 4.6.2.5 the 'interfaces' file of the Universal configuration doesn't work anymore:
août 19 16:14:09 arch64 shorewall[572]: Shorewall configuration compiled to /var/lib/shorewall/.start
août 19 16:14:09 arch64 shorewall[572]: Starting Shorewall....
août 19 16:14:10 arch64 shorewall[572]: ERROR: No network interface available: Firewall state not changed
août 19 16:14:10 arch64 shorewall[572]: [112B blob data]
août 19 16:14:10 arch64 systemd[1]: shorewall.service: main process exited, code=exited, status=143/n/a
août 19 16:14:10 arch64 systemd[1]: Failed to start Shorewall IPv4 firewall.
août 19 16:14:10 arch64 systemd[1]: Unit shorewall.service entered failed state.
The compiling stage worked but the generated script didn't.
I identified the problem to be the usage of the '+' wildcard character in the 'physical' option value of the 'interfaces' file:
#ZONE INTERFACE OPTIONS
- lo ignore
net all dhcp,physical=+,routeback,optional
As I have only one interface 'eth0', I don't need to use a wildcard character and the 'all' value, so I changed the file to:
#ZONE INTERFACE OPTIONS
- lo ignore
net eth0 dhcp,routeback,optional
And the firewall works again after that change.
It's certainly a regression bug introduced in the new releases.
I changed the title of the thread
from:
Newly installed shorewall fails to start
to:
shorewall Universal configuration fails to start
Last edited by berbae (2014-08-22 14:59:46) -
EM Configuration Failed - Error starting DB
Hi There,
I'm trying to isntall Oracle 10gR2 on Oracle Enterprise Linux 4.8 and, while installing I got the following Error in the Database creation step.
Enterprise manager configuration failed due to the following error-
Error starting Database Control
Refer to the log file at /u01/app/oracle/product/10.2.0/db_1/cfgtoollogs/dbca/demo1/emConfig.log for more details.
You can retry configuring this database with Enterprise Manager later by manually running /u01/app/oracle/product/10.2.0/db_1/bin/emca script.
--------tail Log from the Log file
CONFIG: New Env List: [DISPLAY=:0.0, NEED_EXIT_CODE=1, ORACLE_SID=demo1, PATH=/u01/app/oracle/product/10.2.0/db_1/bin:/usr/bin:/usr/bin:/usr/ccs/bin:/u01/app/oracle/product/10.2.0/db_1/bin:/usr/lib/qt-3.3/bin:/usr/kerberos/bin:/usr/local/bin:/usr/bin:/bin:/usr/X11R6/bin:/home/oracle/bin:/home/oracle/10gR2_db/database/install, TZ=]
Mar 21, 2010 6:26:10 PM oracle.sysman.emcp.util.PlatformInterface executeCommand
CONFIG: Starting execution: /u01/app/oracle/product/10.2.0/db_1/bin/emctl start dbconsole
Mar 21, 2010 6:33:13 PM oracle.sysman.emcp.util.PlatformInterface executeCommand
CONFIG: Exit value of 1
Mar 21, 2010 6:33:13 PM oracle.sysman.emcp.util.PlatformInterface executeCommand
CONFIG: TZ set to US/Central
Oracle Enterprise Manager 10g Database Control Release 10.2.0.1.0
Copyright (c) 1996, 2005 Oracle Corporation. All rights reserved.
http://rhel4.localdomain:1158/em/console/aboutApplication
Starting Oracle Enterprise Manager 10g Database Control ............................................................................................. failed.
Logs are generated in directory /u01/app/oracle/product/10.2.0/db_1/rhel4.localdomain_demo1/sysman/log
Mar 21, 2010 6:33:13 PM oracle.sysman.emcp.util.PlatformInterface executeCommand
WARNING: Error executing /u01/app/oracle/product/10.2.0/db_1/bin/emctl start dbconsole
Mar 21, 2010 6:33:13 PM oracle.sysman.emcp.EMConfig perform
EVERE: Error starting Database Control
Refer to the log file at /u01/app/oracle/product/10.2.0/db_1/cfgtoollogs/dbca/demo1/emConfig.log for more details.
Mar 21, 2010 6:33:13 PM oracle.sysman.emcp.EMConfig perform
CONFIG: Stack Trace:
oracle.sysman.emcp.exception.EMConfigException: Error starting Database Control
at oracle.sysman.emcp.EMDBPostConfig.performConfiguration(EMDBPostConfig.java:565)
at oracle.sysman.emcp.EMDBPostConfig.invoke(EMDBPostConfig.java:177)
at oracle.sysman.emcp.EMDBPostConfig.invoke(EMDBPostConfig.java:146)
at oracle.sysman.emcp.EMConfig.perform(EMConfig.java:155)
at oracle.sysman.assistants.util.em.EMConfiguration.run(EMConfiguration.java:426)
at java.lang.Thread.run(Thread.java:534)
############## Preconfig details ############
1. /etc/hosts
[root@rhel4 ~]# cat /etc/hosts
# Do not remove the following line, or various programs
# that require network functionality will fail.
127.0.0.1 localhost.localdomain localhost
192.168.2.154 rhel4.localdomain rhel4
2. .bash_profile
umask 022
ORACLE_BASE=/u01/app/oracle
ORACLE_HOME=$ORACLE_BASE/product/10.2.0/db_1
ORACLE_SID=demo1
PATH=$ORACLE_HOME/bin:$PATH
export PATH
export ORACLE_BASE ORACLE_HOME ORACLE_SID
3. Required Packages check:
libaio-0.3.105-2
[root@rhel4 ~]# rpm -q binutils gcc gcc-c++ glibc gnome-libs libstdc++ libstdc++-devel make \
pdksh sysstat xscreensaver libaio
binutils-2.15.92.0.2-25
gcc-3.4.6-11.0.1
gcc-c++-3.4.6-11.0.1
glibc-2.3.4-2.43
gnome-libs-1.4.1.2.90-44.2
libstdc++-3.4.6-11.0.1
libstdc++-devel-3.4.6-11.0.1
make-3.80-7.EL4
pdksh-5.2.14-30.6
sysstat-5.0.5-25.el4
xscreensaver-4.18-5.rhel4.14.0.1
libaio-0.3.105-2
4.[root@rhel4 ~]# id oracle
uid=500(oracle) gid=501(oinstall) groups=501(oinstall),502(dba)
I have setup all the steps as specified in the Oracle Site, Oracle-Base site..
Can any one tell me what could be the issue..
Since 1 week I'm trying to resolve this issue but, I couldn't ..user3890610 wrote:
Hi Andy, I tried as you mentioned but, no luck. Getting same error.
Please some one help me on this.
Thanks,
RahulIt appears you have a working database, but the creation of the dbcontrol failed at installation/creation. I've seen this several times, due to the db not being registered with the listener.
You are going to have to work at a command line. Sorry about that. ;-)
First make sure your listener is up. (lsnrctl status)
Second make sure the database is up (sqlplus / as sysdba)
Next, make sure your db is registered with the listener (lsnrctl status)
When all that is in place, you will need to drop and recreate your dbcontrol, using the 'emca' utility. I don't have the exact syntax at hand, but given what I've told you so far, it shouldn't be too hard to find the details. You may need to drop the SYSMAN user before recreating/reconfiguring the dbcontrol. -
WRT54G Wireless not cooperating with Wireless Zero Configuration
Hello! I'm wondering if anyone can help me spot out the problems that I have here: For a while this hasn't been too much of an issue, but whenever I try to view the list of Wireless Networks it gives the "Windows cannot configure this wireless connection. If you have enabled another program to manage this wireless connection, use that software." I have gone into the registries to find WZC has been on, and I unchecked/checked the option again to make sure it wasn't a source of the problem. Yet whenever I open the "Wireless Network Connection Status" window I am only given 2 tab options. The General tab, and the Support tab. The third tab is missing, the one that would allow me to check the option of letting Windows configure my wireless settings but I cannot seem to be able to bring that tab back no matter what. Any help at all is greatly appreciated, please and thank you!
Solved!
Go to Solution.This laptop is Windows XP and can connect to the router, the other laptop with Windows Vista can connect to it also.
Edit: Ah before the laptop with Windows Vista wasn't able to connect to the router, after a firmware upgrade it could connect to it just fine but the laptop with XP's problem still existed. -
Windows Zero Configuration does not start automatically
It won't start automatically, even though I have set it to automatic in the Services Tab. Every time the computer goes to sleep, logs out or restarts, I have to go back into Services and restart it. How can I get it to start automatically. NOTE: I HAVE CHANGED THE STARTUP TYPE IN THE SERVICES TAB BUT IT IS TO NO AVAIL (I have asked this question in other places, and they still give me this answer, so I hope you guys are smart enough to not tell me what I already said I did.)
On the recovery tab of the service properties, set them all to restart. Does that work for you? If you can not start a service, there might be some kind of malware or virus that is forcing the service to start. Could also be a corrupted file on the hard drive. If you look at your event logs, does it show what any error messages?
-
Network: Unknown / The dependency service or group failed to start
Hello, MicroSoft tech crew. I know my issue is not something new to you, there are earlier posts with similar to identical problems to mine. For a whole day I tried everything I could find on the internet to fix my issue, but nothing seemed to work.
I cannot connect to the internet. My network and sharing center displays the following, instead of the map:
Unknown
The dependency service or group failed to start.
I am running windows 7 Professional 64-bit.
I used ESET NOD32 as antivirus. I uninstalled it the day this issue appeared.
I have no restore point.
Any other computer or device can successfully connect to my router.
Re-installing a fresh copy of windows is not an option.
These are the solutions I tried and didn't work:
I tried restarting the router (1 minute power-off)
I HAVE reinstalled my drivers for both LAN and WAN network cards at least twice each.
~ I ran the following commands in CMD as administrator over 3 times, successfully, followed by reboot:
* sfc /scannow
* netsh winsock reset // netsh winsock reset catalog
* netsh int ip reset // netsh int ip reset reset.log hit
I have checked the following in the registry:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\servicel\NlaSvc has always had full control and read permissions for both SYSTEM and Administrators.
I replaced my nlasvc.dll file from C:\Windows\System32\ with one from another computer (and set TrustedInstaller as its owner)
Booting in Safe mode with networking does not change this situation.
These are some of my services. Note that I turned some of those from Manual to Automatic.
1) COM+ Event System
* Automatic, Started
2) Computer browser
* Automatic, Started
3) DHCP Client
* Automatic, Stopped
* When I attempt to start this service I get this error message:
"Windows could not start the DHCP Client Service on Local Computer."
"Error 1186: Element not found."
* Dependencies:
3.1) Network Store Interface Service
* Automatic, Started
4) DNS Client
* Automatic, started
5) Network Connections
* Automatic, Started
6) Network Location Awareness
* Automatic, Stopped
* When I attempt to start this service I get this error message:
"Windows could not start the Network Location Awareness service on Local Computer."
"Error 1068: The dependency service or group failed to start"
* Dependencies:
6.1) Network Store Interface Service
* Automatic, Started
6.2) Remote Procedure Call (and all it depends on)
* Automatic, Started
7) Remote Procedure Call (RPC)
* As stated above: Automatic, Started
8) Server
* Automatic, Stopped
* When I attempt to start this service I get this error message:
"Windows could not start the Server service on Local Computer."
"Error 50: The request is not supported."
* Dependencies:
8.1) Security Accounts Manager (and the RPC)
* Automatic, Started
9) TCP/IP Netbios helper
* Automatic, Started
10) Wireless Zero Configuration (XP)
* Nonexistent
11) WLAN AutoConfig
* Automatic, Started
12) Workstation
* Automatic, Started
Also, my ipconfig /all looks very strange. I am not allowed to post pictures yet, but this is the image on skydrive server:
/#cid=2168FA597AC0EAF1&id=2168FA597AC0EAF1%21107I follow your solution and found the
Network Location Awareness service
could not start.
Then I found the solution from:
http://mjmcfalls.wordpress.com/2012/04/07/network-location-awareness-service-terminated-with-service-specific-error-1073741288/
by running the commands:
net localgroup administrators localservice /add
net localgroup administrators networkservice /add
to add the "Localservice" user and "NetworkService" user
to the adminstrators group.
And the problem solved after reboot. -
Windows xp keeps turning wireless zero config.off
I have a new Toshiba PC which was working well until I connected a purchased/used Ipod mini to it in order to restore it. Since then, this PC has been turning the Wireless Zero Config service off and not connecting to our Airport Extreme. If I restart the PC it will configure for awhile and then randomly loose the connection. When I check the Airport Admin the home network is not identified. Other computers in the network have not problems. This seems to have started when I connected the ipod--it zapped something. I anyone can help, I'd certainly appreciate it. I've tried all many of the support sites at Windows and Apple. Thanks, Betty
Toshiba satillite 4324 Windows XPMissing Zero Wireless Configuration Installation
Enable Display Hidden Files
- Open Windows Explorer, click Tools, and select Folder Options.
- Go to the View tab and scroll down until you come across the option “Show Hidden Files and Folders” and check it. Also, uncheck the option “Hide Protected Operating System Files (Recommended).”
- Click OK.
Install the Wireless Zero Configuration Service
- Click the Start button, and then click Control Panel.
- In the Control Panel window, if you’re in Category View, then under Pick a Category, double-click the Network and Internet Connections icon (if you’re in Classic View, click on the Network Connections icon and skip to step #4).
- In the Network and Internet Connections window, under the Control Panel icon, double-click the Network Connections icon.
- In the Network Connections window, under LAN or High Speed Internet, click to select the Local Area Connection icon.
- On the menu bar, click File and select Properties from the file menu. (Altneratively, right-click on the Local Area Connection icon and select Properties from the context menu).
- In the Local Area Connections Properties window, on the General tab, click the Install button.
- In the Select Network Component Type window, in the Click the type of network box, click to select the Service icon.
- Click the Add button.
- In the Select Network Service window, click the Have Disk button.
- Click the OK button.
- In the Install From Disk window, click the Browse button.
- In the Locate File window, browse to the C:\Windows\Inf folder (this is a hidden folder).
- Click to select NETWZC.INF.
- Click the Open button.
- In the Install from Disk window, click the OK button.
- In the Select Network Service window, in the Network Service box, select Microsoft as the manufacturer, and then click to select Wireless Zero Configuration.
- Click the OK button.
At this point you’ll need to reboot your PC. With that completed, you should find that the Wireless Zero Configuration service has been successfully installed on your system and you should now have access to the Windows Network tab.
NOTE: If you don’t see the Wireless Network tab when you go back into the Network Properties Page, then the most likely reason is that the service did not start. To initialize it, open Administrative Tools in the Control Panel and select Services. Scroll down to Wireless Zero Configuration, Right-click on it, and select Start. The service is now enabled, and the Wireless Network tab will be visible in Network Properties. -
WLC 440x 4.2.176 Windows Zero Configuration random disabling
I have a lot of PCs that are running a combo of XP SP2 and SP3 that will randomly stop working and the windows zero configuration service will be stopped and or disabled. They are associated with Cisco access points 1232 access points running LWAPP. Wireless signal strength is not an issue. No coverage problems. I have a small wireless lab setup with 6 wireless laptops all running XP using 802.11G at 54 megs and some will just randomly drop connection and when I go and look the wireless zero configuration is disabled. I use only the built in WIndows wireless to manage my connections. When they stop working they stop working all at the same time, but not all. Some will continue to work just fine. I dont know what else to look at. Has anyone else had this same issue that has a fix? I am currently upgrading the WLC to a new code to see it that has any resolution. The problem is that it is so random I cannot duplicate it.
Thanks.The problem is that its not deauthenticating the user, its just dropping completely and disabling the windows zero configuration in the services. I do not know how or what in the WLC would do this? I really dont think this is anything that I can control. I am guessing that there is an internal conflict on the pc. I have been told that the image used to image the machine has had the manufacturers wireless client utility removed. I did find a DW Utility in the services list. I think that is my problem. I did however go ahead and upgrade them to 5.2.193. All I can do is have the customer monitor and see what happens. Will post an update when I get one.
-
BOE XI R2 - Configuring RAS with Service user, RAS Fails to start...
Colleagues:
Where would kbase article c2018785 be found?
I am configuring my BOE XI R2 to use End-to-End SSO via IIS using this document from Business Objects:
Link: [https://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/403cdf46-c63e-2b10-2997-978cb8ba59f0]
In this document, you create a service user under which certain applications run, including the Report Application Server.
There is a specific note on page 6 in the doc which states:
The RAS server may fail to start under this new service account. If you experience this issue, follow the steps outlined in the following kbase:
Link: [http://support.businessobjects.com/library/kbase/articles/c2018785.asp]
Unfortunately, the link is out of date, and I have not found the article using the existing search tools.
I did use the -trace argument to the command line to start up the RAS service, and the output is follows:
Timestamp ProcessID ThreadID Message
[Thu May 07 13:21:39 2009] 4448 4228 (.ashwin32service.cpp:165): trace message: RAS starting
[Thu May 07 13:21:39 2009] 4448 4228 (.dtsdts.cpp:1794): trace message:
TraceLog 2009 5 7 8:21:39.936 4448 4228 (.dtsdts.cpp:2039): CDTSApp::InitInstance(): In CDTSParameters::RUN
[Thu May 07 13:21:39 2009] 4448 4228 (.dtsdts.cpp:1794): trace message:
TraceLog 2009 5 7 8:21:39.936 4448 4228 (.dtsdts.cpp:2055): CDTSApp::InitInstance(): Starting server. Process Id=4448
[Thu May 07 13:21:39 2009] 4448 4228 (.dtsdts.cpp:1794): trace message:
TraceLog 2009 5 7 8:21:39.936 4448 4228 (.dtsdts.cpp:2062): CDTSApp::InitInstance(): setServerParameters() done
[Thu May 07 13:21:39 2009] 4448 4228 (.dtsdts.cpp:1794): trace message:
TraceLog 2009 5 7 8:21:39.936 4448 4228 (.dtsdts.cpp:2130): CDTSApp::InitInstance(): initLicenseLimit() returns 1
[Thu May 07 13:21:39 2009] 4448 4228 (.dtsdts.cpp:1794): trace message:
TraceLog 2009 5 7 8:21:39.936 4448 4228 (.dtsdts.cpp:3895): CDTSApp::loadServerOptions(): about to SaveToRegistryAsDefault
[Thu May 07 13:21:39 2009] 4448 4228 (.dtsdts.cpp:1794): trace message:
TraceLog 2009 5 7 8:21:39.936 4448 4228 (.dtsdts.cpp:3897): CDTSApp::loadServerOptions(): done SaveToRegistryAsDefault hr=-2147024891
[Thu May 07 13:21:39 2009] 4448 4228 (.dtsdts.cpp:1794): trace message:
TraceLog 2009 5 7 8:21:39.936 4448 4228 (.dtsdts.cpp:3916): CDTSApp::loadServerOptions(): error Access is denied.
[Thu May 07 13:21:39 2009] 4448 4228 (.dtsdts.cpp:1794): trace message:
TraceLog 2009 5 7 8:21:39.936 4448 4228 (.dtsdts.cpp:2134): CDTSApp::InitInstance(): loadServerOptions() returns 0
[Thu May 07 13:21:39 2009] 4448 4228 (.dtsdts.cpp:1794): trace message:
TraceLog 2009 5 7 8:21:39.936 4448 4228 (.dtsdts.cpp:2194): CDTSApp::InitInstance(): getDataEngineName() returns C:TrouxBusiness Objectscommon3.5 incrpe32.dll
[Thu May 07 13:21:39 2009] 4448 4228 (.dtsdts.cpp:1794): trace message:
TraceLog 2009 5 7 8:21:39.936 4448 4228 (.dtsdts.cpp:2197): CDTSApp::InitInstance(): openEngine() returns 0
[Thu May 07 13:21:39 2009] 4448 4228 (.dtsdts.cpp:1794): trace message:
TraceLog 2009 5 7 8:21:39.936 4448 4228 (.dtsdts.cpp:2292): CDTSApp::InitInstance(): preloadMSXML() done
[Thu May 07 13:21:39 2009] 4448 4228 trace message: EnCOMSessionMgr::EnCOMSessionMgr begins...
[Thu May 07 13:21:39 2009] 4448 4228 trace message: EnCOMSessionMgr::EnCOMSessionMgr trying to get Singleton SessionManager.
[Thu May 07 13:21:39 2009] 4448 4228 trace message: CInfoSessionManager::Initialize start
[Thu May 07 13:21:39 2009] 4448 4228 trace message: CInfoSessionManager::Initialize, start the cluster refresh thread
[Thu May 07 13:21:40 2009] 4448 4228 (.dtsdts.cpp:1794): trace message:
TraceLog 2009 5 7 8:21:40.217 4448 4228 (.dtsdts.cpp:2445): CDTSApp::InitInstance(): caught UNKNOWN EXCEPTION!!!
[Thu May 07 13:21:40 2009] 4448 4228 (.dtsdts.cpp:1794): trace message:
TraceLog 2009 5 7 8:21:40.217 4448 4228 (.dtsdts.cpp:2461): CDTSApp::InitInstance() returns 0
[Thu May 07 13:21:40 2009] 4448 4228 (.dtsdts.cpp:1794): trace message:
TraceLog 2009 5 7 8:21:40.217 4448 4228 (.dtsdts.cpp:1039): CAgentMapMT::ShutDown - outstanding agents:
[Thu May 07 13:21:40 2009] 4448 4228 (.ashwin32service.cpp:329): trace message: RAS Exiting: return code = 0
In the Windows event viewer, this error is echoed:
Failed to load Report Application Server settings from the system registry.
Detailed Message: Access is denied.
It seems my service account needs a certain permission to be able to load and read the registry for this application, and I'm sure this permission is discussed in the missing kbase article.
Could you please let me know what permission is required for this user on the OS? This is Win2003 x64 SP2.
Thanks, and have a good dayHi,
if this a permissions problem then just start +regedit*, go to
My Computer\HKEY_LOCAL_MACHINE\SOFTWARE\Business Objects
select it, press the right mouse button and choose Permissions. Press the advanced button and assign your service account with full control at this point of the registry. Do not forget to select the +Replace Permissions Entries on all child objects ... + option.
You can also take a look at Notes 1199630 and 1201489 (this one is for CR 10 but it may be worth it to follow the instructions there) ( [https://service.sap.com/notes])
Regards,
Stratos -
TS3212 Application has failed to start because application configuration is incorrect
Hello
Am hoping for some help please if possible, I have just downloaded the latest version of I-Tunes, when I double click on the .exe to install I get the following message;
This application has failed to start because the application configuration is incorrect. Reinstalling the application may fix this problem.
I've tried searching forums and have seen similar posts - one suggesting it may be a problem with a dll file but gave no further details and another post that suggested it could be the .net framework which I downloaded a fix for from Microsoft but this has not worked unfortunately.
I am running Windows XP Professional Service Pack 3
Any help would be gratefully appreciated
Thank you
RichardClick here and follow the instructions. You may need to completely remove and reinstall iTunes and all related components, or run the process multiple times; this won't normally affect its library, but that should be backed up anyway.
(99596) -
This morning I went to go into Firefox, a message came up stating it was updating. After the update, Firefox didn't open, so I clicked on the icon and got this message. C:\Program Files (x86) Mozilla Fire\firefox.exe. The application has failed to start because its side-by-side configuration is incorrect. I tried removing & re-installing and I even try the Window's restoration point of a couple days back and I still get the message. Has anyone had or have this problem?
You can click the link in my above post if you haven't done that yet.
*https://support.mozilla.org/questions/910134
That SxS error seems to be caused by a corrupted Visual C installation that requires some DLL files to be reinstalled.
*http://www.vistax64.com/software/245768-side-side-configuration-incorrect.html -
When I try to install Itunes64setup software in a w vista 64 notebook I get an error message "The application has failed to start because its side-by-side configuration is incorrect." Can you help me ?
This forum is for questions from those managing sites on iTunes U, Apple's service for colleges and universities to post educational material in the iTunes Store. You'll be most likely to get help with this issue if you ask in the general iTunes for Windows forum.
Regards. -
The application has failed to start because it's side-by-side configuration is incorrect. Please see
When opening preimere pro cs5.5 i get this:
the application has failed to start because it's side-by-side configuration is incorrect. Please see the application event log or use the command-line sxstrace.exe tool for more detailMoving this discussion to the Premiere Pro CS5 & CS5.5 forum.
-
This application failed to start because it's side-by-side configuration is incorrect....
This is a redirected question from
here
While trying to run YouCam.exe, i encountered the error message,
"The application has failed to start because its side-by-side configuration is incorrect. Please see the application event log or use the command-line sxstrace.exe tool for more detail. "
I then searched the forums and installed a slew of updates that mostly VC++ Redistritutable 64-Bit version, DotNetFix etc etc but it still did not work.
I then ran 'Event Viewer' and pulled out the error logs for the YouCam program.
"Activation context generation failed for "C:\Program Files\CyberLink\YouCam\YouCam.exe.Manifest". Dependent Assembly Microsoft.VC80.MFC,processorArchitecture="x86",publicKeyToken="1fc8b3b9a1e18e3b",type="win32",version="8.0.50608.0" could not be found.
Please use sxstrace.exe for detailed diagnosis."
I am using a Fujitsu SH760 laptop which is running a Win7 64-bit Enterprise OS.
Note that I do not have the recovery disk.
Please assist and if you require further information, i will try to give it asap.
Thank You.I ran sxstrace.exe and here is the log file i obtained. Details as follows,
=================
Begin Activation Context Generation.
Input Parameter:
Flags = 0
ProcessorArchitecture = Wow32
CultureFallBacks = en-US;en
ManifestPath = C:\Program Files (x86)\CyberLink\YouCam\YouCam.exe.Manifest
AssemblyDirectory = C:\Program Files (x86)\CyberLink\YouCam\
Application Config File =
INFO: Parsing Manifest File C:\Program Files (x86)\CyberLink\YouCam\YouCam.exe.Manifest.
INFO: Manifest Definition Identity is YouCam,processorArchitecture="X86",type="win32",version="3.0.1104.3278".
INFO: Reference: Kanten.X,type="win32",version="1.0.0.0"
INFO: Reference: Microsoft.VC80.CRT,processorArchitecture="x86",publicKeyToken="1fc8b3b9a1e18e3b",type="win32",version="8.0.50608.0"
INFO: Reference: Microsoft.VC80.MFC,processorArchitecture="x86",publicKeyToken="1fc8b3b9a1e18e3b",type="win32",version="8.0.50608.0"
INFO: Resolving reference Kanten.X,type="win32",version="1.0.0.0".
INFO: Resolving reference for ProcessorArchitecture Kanten.X,type="win32",version="1.0.0.0".
INFO: Resolving reference for culture Neutral.
INFO: Applying Binding Policy.
INFO: No binding policy redirect found.
INFO: Begin assembly probing.
INFO: Did not find the assembly in WinSxS.
INFO: Attempt to probe manifest at C:\Program Files (x86)\CyberLink\YouCam\Kanten.X.DLL.
INFO: Attempt to probe manifest at C:\Program Files (x86)\CyberLink\YouCam\Kanten.X.MANIFEST.
INFO: Manifest found at C:\Program Files (x86)\CyberLink\YouCam\Kanten.X.MANIFEST.
INFO: End assembly probing.
INFO: Resolving reference Kanten.X.mui,language="*",type="win32",version="1.0.0.0".
INFO: Resolving reference for ProcessorArchitecture Kanten.X.mui,language="*",type="win32",version="1.0.0.0".
INFO: Resolving reference for culture en-US.
INFO: Applying Binding Policy.
INFO: No binding policy redirect found.
INFO: Begin assembly probing.
INFO: Did not find the assembly in WinSxS.
INFO: Did not find manifest for culture en-US.
INFO: End assembly probing.
INFO: Resolving reference for culture en.
INFO: Applying Binding Policy.
INFO: No binding policy redirect found.
INFO: Begin assembly probing.
INFO: Did not find the assembly in WinSxS.
INFO: Did not find manifest for culture en.
INFO: End assembly probing.
INFO: Resolving reference Microsoft.VC80.CRT,processorArchitecture="x86",publicKeyToken="1fc8b3b9a1e18e3b",type="win32",version="8.0.50608.0".
INFO: Resolving reference for ProcessorArchitecture WOW64.
INFO: Resolving reference for culture Neutral.
INFO: Applying Binding Policy.
INFO: No publisher policy found.
INFO: No binding policy redirect found.
INFO: Begin assembly probing.
INFO: Did not find the assembly in WinSxS.
INFO: Attempt to probe manifest at C:\Windows\assembly\GAC_32\Microsoft.VC80.CRT\8.0.50608.0__1fc8b3b9a1e18e3b\Microsoft.VC80.CRT.DLL.
INFO: Did not find manifest for culture Neutral.
INFO: End assembly probing.
INFO: Resolving reference for ProcessorArchitecture x86.
INFO: Resolving reference for culture Neutral.
INFO: Applying Binding Policy.
INFO: Find publisher policy at C:\Windows\WinSxS\manifests\x86_policy.8.0.microsoft.vc80.crt_1fc8b3b9a1e18e3b_8.0.50727.4940_none_516d712b0f495a45.manifest
INFO: Publisher Policy redirected assembly version.
INFO: Post policy assembly identity is Microsoft.VC80.CRT,processorArchitecture="x86",publicKeyToken="1fc8b3b9a1e18e3b",type="win32",version="8.0.50727.4940".
INFO: Begin assembly probing.
INFO: Attempt to probe manifest at C:\Windows\WinSxS\manifests\x86_microsoft.vc80.crt_1fc8b3b9a1e18e3b_8.0.50727.4940_none_d08cc06a442b34fc.manifest.
INFO: Manifest found at C:\Windows\WinSxS\manifests\x86_microsoft.vc80.crt_1fc8b3b9a1e18e3b_8.0.50727.4940_none_d08cc06a442b34fc.manifest.
INFO: End assembly probing.
INFO: Resolving reference Microsoft.VC80.CRT.mui,language="*",processorArchitecture="x86",publicKeyToken="1fc8b3b9a1e18e3b",type="win32",version="8.0.50727.4940".
INFO: Resolving reference for ProcessorArchitecture WOW64.
INFO: Resolving reference for culture en-US.
INFO: Applying Binding Policy.
INFO: No publisher policy found.
INFO: No binding policy redirect found.
INFO: Begin assembly probing.
INFO: Did not find the assembly in WinSxS.
INFO: Attempt to probe manifest at C:\Windows\assembly\GAC_32\Microsoft.VC80.CRT.mui\8.0.50727.4940_en-US_1fc8b3b9a1e18e3b\Microsoft.VC80.CRT.mui.DLL.
INFO: Did not find manifest for culture en-US.
INFO: End assembly probing.
INFO: Resolving reference for culture en.
INFO: Applying Binding Policy.
INFO: No publisher policy found.
INFO: No binding policy redirect found.
INFO: Begin assembly probing.
INFO: Did not find the assembly in WinSxS.
INFO: Attempt to probe manifest at C:\Windows\assembly\GAC_32\Microsoft.VC80.CRT.mui\8.0.50727.4940_en_1fc8b3b9a1e18e3b\Microsoft.VC80.CRT.mui.DLL.
INFO: Did not find manifest for culture en.
INFO: End assembly probing.
INFO: Resolving reference for ProcessorArchitecture x86.
INFO: Resolving reference for culture en-US.
INFO: Applying Binding Policy.
INFO: No publisher policy found.
INFO: No binding policy redirect found.
INFO: Begin assembly probing.
INFO: Did not find the assembly in WinSxS.
INFO: Attempt to probe manifest at C:\Windows\assembly\GAC_32\Microsoft.VC80.CRT.mui\8.0.50727.4940_en-US_1fc8b3b9a1e18e3b\Microsoft.VC80.CRT.mui.DLL.
INFO: Did not find manifest for culture en-US.
INFO: End assembly probing.
INFO: Resolving reference for culture en.
INFO: Applying Binding Policy.
INFO: No publisher policy found.
INFO: No binding policy redirect found.
INFO: Begin assembly probing.
INFO: Did not find the assembly in WinSxS.
INFO: Attempt to probe manifest at C:\Windows\assembly\GAC_32\Microsoft.VC80.CRT.mui\8.0.50727.4940_en_1fc8b3b9a1e18e3b\Microsoft.VC80.CRT.mui.DLL.
INFO: Did not find manifest for culture en.
INFO: End assembly probing.
INFO: Resolving reference Microsoft.VC80.MFC,processorArchitecture="x86",publicKeyToken="1fc8b3b9a1e18e3b",type="win32",version="8.0.50608.0".
INFO: Resolving reference for ProcessorArchitecture WOW64.
INFO: Resolving reference for culture Neutral.
INFO: Applying Binding Policy.
INFO: No publisher policy found.
INFO: No binding policy redirect found.
INFO: Begin assembly probing.
INFO: Did not find the assembly in WinSxS.
INFO: Attempt to probe manifest at C:\Windows\assembly\GAC_32\Microsoft.VC80.MFC\8.0.50608.0__1fc8b3b9a1e18e3b\Microsoft.VC80.MFC.DLL.
INFO: Did not find manifest for culture Neutral.
INFO: End assembly probing.
INFO: Resolving reference for ProcessorArchitecture x86.
INFO: Resolving reference for culture Neutral.
INFO: Applying Binding Policy.
INFO: No publisher policy found.
INFO: No binding policy redirect found.
INFO: Begin assembly probing.
INFO: Did not find the assembly in WinSxS.
INFO: Attempt to probe manifest at C:\Windows\assembly\GAC_32\Microsoft.VC80.MFC\8.0.50608.0__1fc8b3b9a1e18e3b\Microsoft.VC80.MFC.DLL.
INFO: Attempt to probe manifest at C:\Program Files (x86)\CyberLink\YouCam\Microsoft.VC80.MFC.DLL.
INFO: Attempt to probe manifest at C:\Program Files (x86)\CyberLink\YouCam\Microsoft.VC80.MFC.MANIFEST.
INFO: Attempt to probe manifest at C:\Program Files (x86)\CyberLink\YouCam\Microsoft.VC80.MFC\Microsoft.VC80.MFC.DLL.
INFO: Attempt to probe manifest at C:\Program Files (x86)\CyberLink\YouCam\Microsoft.VC80.MFC\Microsoft.VC80.MFC.MANIFEST.
INFO: Did not find manifest for culture Neutral.
INFO: End assembly probing.
ERROR: Cannot resolve reference Microsoft.VC80.MFC,processorArchitecture="x86",publicKeyToken="1fc8b3b9a1e18e3b",type="win32",version="8.0.50608.0".
ERROR: Activation Context generation failed.
End Activation Context Generation.
Maybe you are looking for
-
Classification, Batch Management, Serialisation Profile along with QM
Hi All GURUS, I have very interesting scenario to work on. My client requirement is to identify produciton lot seperately and maintain production data seperately for each production lot. Also for some materials client requires to maintain uni
-
Exception while trying to deploy to portal
Dear all, I have a serious deploy problem with the SAPNWCE71TrialSP1Preview_DevStudio in combination with SAP WAS... This is the error message Reason: Clusterwide exception: server ID 23000550:com.sap.engine.services.deploy.exceptions.ServerDeploymen
-
Address Book Distribution List - Multi Selection
In sending email to all members of a Smart Group, I need to send to more than one address per vCard (e.g. home AND work email, or his AND her address) But Edit Distribution List won't allow multiple selections. Is there a work around?
-
Could not establish trust relationship for the SSL/TLS secure channel with authority
Hello everyone, I need to establish a connection between my HTTPS WCF hosted in Windows Azure Web Role and my Windows Store App Client. The service is actually exposed for testing purposes using a self-signed certificate. I have installed the certifi
-
Trouble: Keynote to .swf being viewed on CourseMill LMS
I'm using Keynote 4 to present content that I'm exporting as Flash files. Each file is 1 Keynote slide. and works fine as .swf files in my authoring system (Lectora) particularly when I export to HTML, CD-ROM or as executable files. However, when I u