Wiring diagram of SC 2345

I am trying to figure out how the connections are made between the signal conditioning modules on my SC 2345 board and the board's J24 connecter and screw terminals. For example, I have an AI02 at channel 0/8 and I want to know where + and GND connect to this. Basically any wiring diagrams or tables with pin layouts will probably help me out quite a bit.

Check out page B-2 in the SC-2345 user's manual: http://www.ni.com/pdf/manuals/371064c.pdf
You will notice that each analog input slot on the SC-2345 can output two different Nonreference Single-ended (NRSE) signals to the Data Acquisition board that is connected to the 68-pin connector at J24. If you have a SCC-AI02 connected to J1, then it has two differential analog input signals which are conditioned and passed to the DAQ board as two separate single-ended signals to channels AI0 and AI8 on the 68-pin connector. You can look up the e-series pinout with the e-series user's manual: http://digital.ni.com/manuals.nsf/websearch/05A25C65C755D8DB86256FD30081687D. You will see that AI0 and AI8 correspond to pins 68 and 34 on the 68 pin connector. Page 11 of the SCC-AI user's manual: http://www.ni.com/pdf/manuals/323089a.pdf describes the inner-workings of the module, which will also give you some additional insight into the connections.
If you are just getting started with SCC and want to know how to configure it in software, then there is an SCC quick start guide that may also be of use to you: http://digital.ni.com/manuals.nsf/websearch/5D08FA2610E23C4A86256FB1005880FA
I hope that helps.
Logan Kunitz

Similar Messages

  • I'm replacing my motherboard for ane9220yl pavilion elite. I'm looking for a wiring diagram

     I'm replacing my motherboard for HP pavilion Elite e9220yl. I need a wiring diagram to help me make sure I'm rewiring correctly.
    This question was solved.
    View Solution.

    That depends on what type of connection your display has and whether or not your PC has a video card used for display or if you are using the onboard video outputs.
    Do you really mean PC monitor ( the old school kind) or did you mean to say LCD display (thin flat screens) instead?
    Use the setup poster.
    ****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
    2015 Microsoft MVP - Windows Experience Consumer

  • Convert MathScript node to regular wired diagram

    I wrote a program last year in LabView 8.6, with some MathScript codes in it.  But this year, after I upgraded LabView to 2009 Full Development System, I am not able to run this program anymore because I didn't purchase the MathScript Module.  And what even worse is, when I wrote the program, I shrinked the script node frame too much in order to save some room, but now I cannot even drag the frame bigger.  So now everything is hidden inside the script frame and I cannot see what's inside.  Is there anyway that I can find out what's inside the script node so I can translate them to regular wired diagram?  Thank you in advance.
    Message Edited by Support on 03-04-2010 02:25 PM

    Hello,
    Unfortunately there's no way to see your code without MathScript being installed. This seems like an overzealous restriction, so I have filed a bug report (ID 211321) to allow resizing and exporting text in a future version.
    In the meantime, I can think of two options. You could install the MathScript RT Module in Evaluation mode. This will let you try it out for 30 days for free. Or I'd be happy to copy the text from your nodes and post it on the forums. If you'd like me to do that, just let me know which VIs to look at in your ZIP file.
    jattas
    LabVIEW MathScript R&D

  • I need wiring diagram for Sony XM-2020 2 channel amplifier

    I need a clear picture of a Sony XM-2020 2 channel amplifier. The wiring diagram please.
    Solved!
    Go to Solution.

    Hello Shavonna,
    Welcome to the Sony community forums.
    I agree the one on the website is a bit fuzzy,
    I have  located an original and rescaned it for you.  hope this helps.

  • S5120Y Slimline Case Wiring Diagram

    I'm repairing an HP Pavilion S5120Y Slimline. I've been searching for a Slimline Case Wiring Diagram to help identify the correct front panel compnent wiring to install onto my ASUS P5G41T-M LX Plus motherboard. I have the diagram for the motherboard but I want to insure connecting the wires corectly to prevent damage to the board or the components.
    Anyone have a link to this would be much appreciated.
    This question was solved.
    View Solution.

    Your 4-pin cable from the HP 6-in-1 reader is a USB 2.0 connection.
    WATCH POLARITY -- POWER, GROUND.
    You can damage motherboard USB IC, Surface mount; OR 6-in-1 Reader.
    HP had a bad habit of using various Cable Kluges on their Front Panel wiring
    to support a variety of motherboards.
    Largely due to lack of USB 2.0 headers on motherboards, a decade ago.
    ** You should see their a000 computer case wiring ! ** (I have one, retrofitting to Intel standards).
    ===
    The Optical CD/DVD may be an LED or a simple switch. Did it originally connect to Drive or Motherboard?
    May not be supported on Asus motherboard ...

  • Wiring Diagram for an MS5182

    I have recently acquired an old MS5182 motherboard from a car boot sale and i am trying to set it up as a system for my daughter in her bedroom purely for her schoolwork,the board itself is in perfect condition but i have had no luck finding the wiring diagram for power switch,reset switch etc, I have downloaded the manual from MSI but that only gives the basics can anybody out there help?

    I don't know if your board has the same indications but for most of them, they have abbrev for the connectors on the board itself.
    In the manual that you've download, it is actually in 5182-2.pdf, page 18 of the manual in pdf format.
    I've downloaded the manual from this link below. Please note that the manual consist of 5 different pdf files and the one you are looking for is in "5182-2.pdf".
    http://www.msi.com.tw/program/support/manual/mnu/spt_mnu_detail.php?UID=230&kind=1

  • Typical wiring diagram

    Can anyone direct me to the typical wiring diagram of a Fios DVR multiple room tv system,internet and phone. I currently have DTV with 5 tvs all inter linked and operational from any room. I want to continue this setup but need to run new wiring( based on where my satelitte enters my house verse where cable enters) where they would put the fiber panel. I want to run all the wiring myself and just let this tech plug in the main feed line.

    While I agree with Telcoguru that there is no such thing as a "typical" FiOS installation, there are installations that are "fairly common" or "simple." I view mine fitting into the "simple" category, with two exceptions:
    1) I have Cat5 from the ONT to my Actiontec router. This is because I installed FiOS Internet 3 1/2 years ago, before TV was available, and before the ability to use coax only became available. Since I already had cat5 installed, I chose to continue using it when I got an Actiontec about 6 months ago. A normal installation today will not have cat5 from the ONT to the router, unless you install it yourself, so just ignore it.
    2) I have a PC at the other end of the house from the router, and do not have any cat5 run to that area. I wanted to have wired access for that PC, and since I had a leftover NIM100 from the original installation years ago, I used it to provide cat5 connectivity for that PC. Just ignore the splitter and NIM and assume a cat5 connection from a LAN port on the router to that PC.
    I have three TVs, one HD DVR and two SD STBs, two wired PCs and one wireless.
    Here is a link to my diagram: FiOS Wiring Diagram
    Maybe this will help some.
    Justin
    Verizon FiOS TV, Internet, and phone
    IMG 1.6.0, Build 06.89
    Keller, TX

  • Power switch wiring diagram for hp a867c

    does anyone know where I can get a diagram for the power switch wire hookup?  there are 3 sets of wires labeled hdd led, reset sw, and power led.  they plug in on the motherboard on the bottom right corner.  they came unhooked and know it will not power up.  Thanks in advance

    Will this help
    I am a volunteer. I am not an HP employee.
    To say THANK YOU, press the "thumbs up symbol" to render a KUDO. Please click Accept as Solution, if your problem is solved. You can render both Solution and KUDO.
    The Law of Effect states that positive reinforcement increases the probability of a behavior being repeated. (B.F.Skinner). You toss me KUDO and/or Solution, and I perform better.
    (2) HP DV7t i7 3160QM 2.3Ghz 8GB
    HP m9200t E8400,Win7 Pro 32 bit. 4GB RAM, ASUS 550Ti 2GB, Rosewill 630W. 1T HD SATA 3Gb/s
    Custom Asus P8P67, I7-2600k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX660 2GB, 750W OCZ, 1T HD SATA 6Gb/s
    Custom Asus P8Z77, I7-3770k, 16GB RAM, WIN7 Pro 64bit, EVGA GTX670 2GB, 750W OCZ, 1T HD SATA 6Gb/s
    Both Customs use Rosewill Blackhawk case.
    Printer -- HP OfficeJet Pro 8600 Plus

  • HP PAVILION SLIMLINE S5713W-B INSIDE WIRING DIAGRAM

    HELLO I HAVE A VERY SMALL 4 PIN CONNECTION WIRE WHICH IS BLUE/BLACK IN COLOR AND I FORGOT WHERE IT GOES. I REMOVED ALL 3 FANS TO CLEAN THEM. CD PLAYER IS WORKING AND HARD DRIVE IS WORKING ALL FANS WORKING. CAN SOMEONE HELP

    Hi,
    Review the motherboard layout diagram for your PC.  Check the F-line IN in the lower left hand corner.
    If this above is not the solution then trace the wire back to the other end and let us know where it terminates.
    HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
    HP Photosmart Premium C309G, HP Photosmart 6520
    HP Touchpad, HP Chromebook 11
    Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
    Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
    Windows 7/8 UEFI/Legacy mode, MBR/GPT

  • Wiring Diagram TV/DVD/FIO​S DVR

    Trying to connect a QIP6416 Fios DVR and my DVD player to a non HD TV.
    Any diagrams for that?  The only ones I find say VCR?  Hoping this is actually possible.
    I have coax in to DVR, what's next?
    Thanks

    So ... look at the back of your TV and DVD players and let us know the labels on all of the inputs or outputs -- or better still post the exact make and model number of your TV and DVD player and we can probably find a user guide online that has the diagram we need to see in order to tell you the best way to connect things together.  Should be possible, but need to see what the capabilities of the devices are first.

  • Video out wire diagram for ipod touch

    I have an older portable stereo with ipod dock and video out..  I want to rewire the stereo to charge and get video out from a 4th gen Ipod touch. I need to know what pins are used or a wiring diagram.    please help thank you..

    The hardware on the 4G can't support iOS 7.
    All the iOS devices compatible (iPhone 4 and later, iPad 2 and later, and 5G iPod touch) with iOS 7 have at least 512 MB of memory. The 4G only has 256 MB
    Also, you are not addressing Apple here. We are all just users like yourself.

  • C200 AC Adapter Pin Wiring

    Hi
    The wiring at the base of the DC pin on the AC Adapter for my daughters C200 was damaged when someone tripped over the AC cord, jerking the whole adapter. As a result the charging is very intermittent.
    Does anyone have a wiring diagram so i can resolder the wiring correctly as a new adapter is around $AUS 200 which seems quite a lot to solve a problem that can be fixed by a simple soldering job.
    Regards
    Andrew

    This may help; I found the hardware service  manuals:
    http://www-307.ibm.com/pc/support/site.wss/document.do?sitestyle=lenovo&lndocid=MIGR-66339
    RGDS
    Colin

  • Compaq Presario CQ50-139WM. Installing new DC jack, using existing wiring harness

    Need to know how to attach wiring harness to dc power jack connector socket - cannot locate wiring diagram

    You should buy the dc jack replacement that has the cable already connected, there are no wiring diagrams available.
    http://www.ebay.com/sch/i.html?_from=R40&_trksid=p5197.m570.l1313&_nkw=hp+486637-001&_sacat=See-All-...
    original HP part number is 486637-001

  • Place an image on the block diagram

    Is there an easy way to place an image on the block diagram?
    To clarify, I would like a simple way to paste a bmp or jpeg or png or whatever onto my block diagram for the purpose of documenting the block diagram for future programmers.
    The way I currently accompish this is by creating a picture constant on the diagram and running a seperate vi to load a picture into a picture window, then using copy and paste functions to get the image into the picture constnat in my block diagram.
    There's a simpler way, right?
    global variables make robots angry
    Solved!
    Go to Solution.

    Thanks, but that isn't at all what I am trying to do. I want to
    place an image on the block diagram, not read an image. I've attached a
    screen shot of my block diagram to show you that I am using an image
    that I pasted onto the block diagram to document the block diagram. The
    picture below the wiring is a schematic of a rectangular reticle that
    corresponds to the wiring diagram above. You can see which points go
    where when drawing the targeting reticle around kermit the frog, so it
    is easier to understand the wiring diagram.
    The method
    I have to use to paste an image into the block diagram is cumbersome. I
    would like to know if there is an easy way to paste an image into the
    block diagram.
    Message Edited by Root Canal on 01-10-2009 01:53 PM
    global variables make robots angry
    Attachments:
    like_this.PNG ‏73 KB

  • Wiring for a Symbol SPT17xx RJ45 to DB9 or where to find

    I have (as I have mentioned) the Symbol SPT1700 and SPT1740 with the charging cradle. I was able to repair the charging cradle (blown input capacitor and shorted voltage regulator), but I still need a cable to connect the RJ45 on the cradle to a DB9 serial port to HotSync. I thought I read that the original cable was a null modem cable, so I wired it up as such (or so I thought) but I cannot get it to sync.
    Can someone please give me a pin to pin wiring diagram to go from the RJ45 to a DB9 or tell me where I might can find this information? I don't see spending $25 to $30 for a cable that I can build myself for less than $5... I mean, I did spend three hours troubleshooting a SMT charging cradle instead of just buying a new one.
    Post relates to: Palm Pilot

    Did you ever figure this out? I have the SPT 1700 and 1800 that I want to do. actualy I want to convert it to db25 then use my serial to usb.

Maybe you are looking for