WiSM-2 Module and VSS 6500

Hello
What consequences could i have if i install a WiSM-2 module into a pair of 6500 configured in VSS and another WiSM-2 module into other pair of 6500 configured in VSS for serving a 300  APs??...in this case, do i need to configure mobility groups for guarantee a high availability and also redundancy of controllers??
Under the best practices, is much better having the two WiSM-2 modules into a single pair of 6500 configured in VSS??
I hope my question is gonna be understood if not just let me kow to explain better.
Thanks,
AM

You always need to configure mobility groups if your wlc will share the same mobility. Like Steve mentioned it is wise to split the WiSMs between both chassis. Just because you are doing VSS between the 6500's doesn't mean the WiSM2 will work like VSS, you need to configure the wlc or redundancy if that is what try will be used for.
Thanks,
Scott Fella
Sent from my iPhone

Similar Messages

  • Controllers in the same WISM module in the 6500, i'm trying to make one of them anchor controller for guest internet

    I have 2 controller in the same WISM module and I'm trying to make one of them Anchor controller for guest WLAN, but when I give put the anchor controller in a separated non-routed VLAN and connect it to an outside switch by creating VLAN 192 on the core. ( the Internet router is connected to the same switch).-it is showing path down... ( VLAN 192 visitor Internet and VLAN 224 my internal controller management VLAN are not talking)
    there is no routing between these 2 VLAN ( because of security), but i can't get the controller to communicate.
    -if I connect my laptop to this switch I'm able to go out on Internet but my visitor WLAN is not able to get IP address from the router connected to this switch.
    - I called Cisco and one the guys told me that i can leave the management in VLAN 224 for the controller to communicate ( which they did), but the issue I'm having right now is that my visitors are not getting IP addresses from this VLAN at all
    some one please advise
      vlan192   4/1 vlan 192              int g0/0 192.168.2.201
      6500 ----- switch ---- router---------  (outside)
        |         |   |
        |        DHCP server
       WLC

    A couple of questions, is VLAN 192 allowed across the trunk link to the wlc?  Do you have an interface tagged for vlan 192, with a valid address?  What is providing the DHCP?
    Cheers,
    Steve
    If  this helps you and/or answers your question please mark the question as "answered" and/or rate it, so other users can easily find it.

  • Configure port channel between IO Module and FI

                       Hi,
    I have the current setup
    UCS chassis (4 uplinks) --> FI --> (Port channel) --> N5K --> (port channel) --> VSS 6500
    I configure port channel between IO Module and the FI by changing to policy to "Port Channel" and set the link to 4
    FI has created a portchannel under "Internal" containing all the FI interfaces that are connected to the IO module.
    I have installed ESXI on a blade but i was unable to reach it, even the esx was unable to ping the gateway.
    VLAN tagging is enabled from the ESX server.
    I have issued the command "show mac address-table | inc <mac address of the vnic assigned from thre service profile> on both the N5K and thr 6500 and the mac is there.
    I have allowed all the vlans on the vNIC from the service profile.
    am I missing anything?
    thanks

    Hello,
    Can you please check whether your ESXi vmkernel interface ip address learned on right VLAN on FI / upstream switch or not.
    connect nxos
    show mac-address-table | inc 
    Padma

  • Modules Gbic Catalyst 6500

    I have a peculiar problem with two gbic modules of Catalyst 6500.
    First problem, I have a gbic port in module 7, which was a trunkport to Catalyst 2950, that does not allow conection to switch Catalyst 2950, and besides it harmed the yield of Catalyst 6500. I have to disconnect the optical fiber cable so that everything returned to normality.
    Second problem. A port gbic in module 8, I let work and I disconnect of the network to one of the servants, by such reason I had to connect the fiber cable in another one gbic of he himself I module.
    My question is: is necessary to change I modulate 7 and 8 not to have network problems on watch? or single to change gbic affected in each one of the modules?
    Thank you,

    Failure to get GBIC up during installation could be as a result of system requirements not met, incorrect cable installed, lack of power to the device, configuration errors or hardware failure. Verify that the GBIC cable is connected to another active network device and that the port is not shut down. Replace cable with a known good cable. Make sure GBICs are matched on either side of the connection. Make sure the flow control and port negotiation settings are consistent on both sides of the link. There may be incompatibilities in the implementation of these features if the switches being connected are from different vendors. If in doubt, turn these features off on both switches. Swap GBIC to a different slot. Also, try using a spare GBIC to see if it works. For more information, refer to Troubleshooting link :
    http://www.cisco.com/en/US/products/hw/switches/ps628/products_installation_guide_chapter09186a00800d7681.html

  • ACE20-MOD-K9 and ACE10-6500-K9 in redundant mode

    Can ACE20-MOD-K9 and ACE10-6500-K9 be configured to work togeather as redundant pair?

    ACE10-6500-K9 and ACE20-MOD-K9 modules can occupy the same chassis.
    http://www.cisco.com/en/US/docs/interfaces_modules/services_modules/ace/installation/note/aceinote.html

  • Memory modules and hard drive not recognized

    I removed and reinserted the factory installed Satellite L505D-LS5007 laptop hard drive and memory modules just as practice for installing a hard drive upgrade and an 8GB memory upgrade. The problem is obviously with the memory and not with the hard drive.
    After the first practice try, one memory module was recognized. Also for a few seconds after the first practice try, I ran the PC with the battery installed, but no memory installed. I did not look in the User's Guide first to see that I should have removed the battery before removing the memory.
    Now the System Indicator Lights for the HDD Activity and Memory Card Reader do not light up. The PC turns on and the display is solid black with no messages.
    Before buying new memory modules, what possible ways might there be to get the PC to recognize the factory installed memory modules and hard drive again?
    Solved!
    Go to Solution.

    When troubleshooting, I always change one variable at a time. I would hate to miss a solution by being in a hurry. In this case, you may have damaged either the RAM or the RAM slot. I would stick with the Toshiba specifications for the RAM, making sure it is the correct size, speed and type recommended. I also recommend that when you replace the RAM that both modules be from the same manufacturer, size, and specification. Try one RAM module in one slot and then the other. And then try both RAM modules in both slots. After the testing you should be able to figure if this is a RAM problem or a RAM slot problem.
    In the case of hard drives, the real test is whether or not the Bios sees the hard drive. If the Bios doesn't see the hard drive, it's not going to work. The Bios should see the hard drive whether or not the hard drive is partitioned, formatted or has data on it. My experience has been that many Toshiba laptops will work fine with larger capacity hard drives provided they are the same speed in RPMs, have the same interfacing connection and physically the same size.
    Again, prior to doing any work on your computer, make sure that both the AC power has been disconnected and the battery has been removed. Be careful out there. A blown repair job by a non-Toshiba tech is NOT covered under warranty.

  • Who worked with ICS' Model 4896 GPIB? I can not count the data from the module. Can prompt as it to make. It is desirable with examples (data read-out from the module and data transmission between channels. It is in advance grateful.

    I can not count the data from the module. Can prompt as it to make. It is desirable with examples (data read-out from the module and data transmission between channels. It is in advance grateful.

    Hello. Most of the engineers in developer exchange are more familiar
    with NI products. Contacting ICS for technical support is a better
    course of action.

  • Problem with modules and ModuleLoader

    Hi everybody,
    i'm facing a real funny problem with modules and
    moduleLoader, i hope
    it's not (only) my fault anyway...
    If i create a normal flex project with fBuilder, i'm able to
    use
    modules in a lot of different ways (as mxml, as as in a
    function etc..)...
    but if i try to use them in my fds application (created with
    fds
    eclipse plugin or as a dataServices project) i can't use
    modules. The compile-time error message is
    always the same:
    Could not resolve <mx:ModuleLoader> to a component
    implementation
    I tried a lot of solutions, paying attention to import all
    the classes, to declaration, naming, positioning
    etc...but nothing changes, this thing is drivining me
    crazy!!!.
    I will appreciate anykind of help.
    TIA
    Fabio

    Any idea?

  • Required help on Function Modules and Bapis

    Web portal publishing of ERS invoice letters. This involves modification in the BAPI screens to show the invoice PDF instead of printing??
    can anyone help me in fixing this issue.

    hi Anjaneyulu,
    open the t-code --> and go to menu system->status-->select the program and open the program-->
    selct the tree structure----in the left side the includes screen and function module everthing will show..
    or
    open the t-code --> and go to menu system->status-->select the program and open the program-->
    go to attributes and select the Package..
    next----
    go to se80--> enter the package --> and dispalay it shows the list of Program , include transaction function modules and bapi's under the pakage
    Regards,
    Prabhudas

  • Examples for using function modules and BApis.

    My Dear FRNDS,
    I am very new to ABAP. And I have read the documentation for  function modules but i am not that clear to practice them.So I would be very happy if u people share a little bit of ur experience with me.
    Please provide me some examples of all the use cases in function modules and specially exception handling.
    Frnds, i am going to work with bapis so i feel practicing function module will give me a edge.
    and please tell me after calling a BAPI FM why we have to perform   'BAPI_TRANSACTION_COMMIT' and 'BAPI_TRANSACTION_ROLLBACK'.
    .Ur efforts  will be greatly rewarded.
    thx,
    reshali

    Hi,
    Please check this sample codes.
    DATA: BAPI_Z05DOGI_DELIVERY LIKE BAPIOBDLVHDRCON-DELIV_NUMB ,
    BAPI_Z05DOGI_HEADER_DATA LIKE BAPIOBDLVHDRCON OCCURS 0 WITH HEADER LINE ,
    BAPI_Z05DOGI_HEADER_CONTROL LIKE BAPIOBDLVHDRCTRLCON OCCURS 0 WITH HEADER LINE,
    BAPI_Z05DOGI_ITEM_DATA LIKE BAPIOBDLVITEMCON OCCURS 0 WITH HEADER LINE,
    BAPI_Z05DOGI_ITEM_CONTROL LIKE BAPIOBDLVITEMCTRLCON OCCURS 0 WITH HEADER LINE ,
    BAPI_Z05DOGI_RETURN LIKE BAPIRET2 OCCURS 0 WITH HEADER LINE .
    CLEAR: BAPI_Z05DOGI_DELIVERY , BAPI_Z05DOGI_HEADER_DATA , BAPI_Z05DOGI_HEADER_CONTROL , BAPI_Z05DOGI_ITEM_DATA ,BAPI_Z05DOGI_ITEM_CONTROL , BAPI_Z05DOGI_RETURN .
    REFRESH: BAPI_Z05DOGI_HEADER_DATA , BAPI_Z05DOGI_HEADER_CONTROL , BAPI_Z05DOGI_ITEM_DATA , BAPI_Z05DOGI_ITEM_CONTROL , BAPI_Z05DOGI_RETURN .
    BAPI_Z05DOGI_DELIVERY = ZMM_WB1-ISSUE .
    BAPI_Z05DOGI_HEADER_DATA-DELIV_NUMB = ZMM_WB1-ISSUE.
    APPEND BAPI_Z05DOGI_HEADER_DATA.
    BAPI_Z05DOGI_HEADER_CONTROL-DELIV_NUMB = ZMM_WB1-ISSUE.
    BAPI_Z05DOGI_HEADER_CONTROL-POST_GI_FLG = 'X'.
    APPEND BAPI_Z05DOGI_HEADER_CONTROL.
    BAPI_Z05DOGI_ITEM_DATA-DELIV_NUMB = ZMM_WB1-ISSUE.
    BAPI_Z05DOGI_ITEM_DATA-DELIV_ITEM = 10.
    BAPI_Z05DOGI_ITEM_DATA-DLV_QTY = LFIMGGIA.
    BAPI_Z05DOGI_ITEM_DATA-SALES_UNIT = XTAB-MEINS.
    BAPI_Z05DOGI_ITEM_DATA-DLV_QTY_IMUNIT = LFIMGGIA.
    BAPI_Z05DOGI_ITEM_DATA-FACT_UNIT_NOM = UMVKZLIPS.
    BAPI_Z05DOGI_ITEM_DATA-FACT_UNIT_DENOM = UMVKNLIPS.
    APPEND BAPI_Z05DOGI_ITEM_DATA.
    BAPI_Z05DOGI_ITEM_CONTROL-DELIV_NUMB = ZMM_WB1-ISSUE.
    BAPI_Z05DOGI_ITEM_CONTROL-DELIV_ITEM = 10.
    BAPI_Z05DOGI_ITEM_CONTROL-CHG_DELQTY = 'X'.
    APPEND BAPI_Z05DOGI_ITEM_CONTROL.
    CALL FUNCTION 'BAPI_OUTB_DELIVERY_CONFIRM_DEC'
    EXPORTING
    DELIVERY = BAPI_Z05DOGI_DELIVERY
    HEADER_DATA = BAPI_Z05DOGI_HEADER_DATA
    HEADER_CONTROL = BAPI_Z05DOGI_HEADER_CONTROL
    TABLES
    ITEM_DATA = BAPI_Z05DOGI_ITEM_DATA
    ITEM_CONTROL = BAPI_Z05DOGI_ITEM_CONTROL
    RETURN = BAPI_Z05DOGI_RETURN.
    CALL FUNCTION 'BAPI_TRANSACTION_COMMIT'
    EXPORTING
    WAIT = 'X'
    IMPORTING
    RETURN = BAPI_Z05DOGI_RETURN.
    Go thru this link
    http://www.planetsap.com/LIST_ALL_BAPIs.htm
    BAPI_TRANSACTION_COMMIT
    Execute external Commit when using BAPIs
    This method executes a COMMIT WORK command. It is required for
    transactions developed externally to the R/3 System that change data in
    the R/3 System via BAPI calls.
    When you call BAPIs in your program that change data in the R/3 System,
    afterwards you must call this method to write the changes to the
    database.
    COMMIT WORK
    The statement COMMIT WORK completes the current SAP LUW and opens a new one, storing all change requests for the currenta SAP LUW in the process
    there are some FM that we use for creating trasaction . for example FM : that use for creating production order . if you execut the FM , the system will not create any data in the system so you need to excute the FM : BAPI_TRANSACTION_COMMIT to commit that creating the production order .
    in case of commit work, that is a syntax in abap program . if you use this syntax after you insert ,update or delete table in the sap ,system will do it immediately otherwise the system will do it after execution is complete.
    ROLLBACK WORK.
    for confirming or undoing database updates. COMMIT WORK always concludes a database LUW and starts a new one. ROLLBACK WORK always undoes all changes back to the start of the database LUW.
    Regards,
    Raj.

  • Function modules and BAPIs for a transactio code

    Hi friends,
    How i can find  the List of function modules and BAPIs being used for a particular transaction code?
    for example: I would like to find List function modules and BAPIs being used for the Transaction code
    "FBRA"(Reset cleared items)?
    Any sort of help on this will be helpful.
    Thanks,
    Punjaala

    hi Anjaneyulu,
    open the t-code --> and go to menu system->status-->select the program and open the program-->
    selct the tree structure----in the left side the includes screen and function module everthing will show..
    or
    open the t-code --> and go to menu system->status-->select the program and open the program-->
    go to attributes and select the Package..
    next----
    go to se80--> enter the package --> and dispalay it shows the list of Program , include transaction function modules and bapi's under the pakage
    Regards,
    Prabhudas

  • SAP R/3 Modules and transactions belonging to them.

    Hello there,
    I have two questions which I would like some help with:
    Q1  Is there a link to documentation that lists all the SAP R/3 functional modules and provides an overview/description of each module?
    Q2  I would like to list all the transactions belonging to a fuctional module/area such as SD, MM, PM, FI/CO etc. I know that tables TSTC & TSTCT will provide a list of all the transaction codes, but is there a table that will show all transaction codes belonging to a specific fuctional module?.. if not then is there another way of getting this information?...Please bear in mind that I need to be able to download this information to an excel spreadsheet.
    Your help here would be much appreciated.
    Many thanks
    Sharon

    Hi williams,
    >> For your query regarding SAP R/3 modules refer: http://en.wikipedia.org/wiki/SAP_R/3
    >> For your query regarding Transaction codes refer:
    http://www.easymarketplace.de/transactions.php
    www.erpgenie.com/sapgenie/docs/useful-tcodes.pdf
    Reward points if its useful...

  • Photos in Library module and after export look different than in Development module

    Hello,
    I experience a problem.
    After I update photos in the Development module, the updates seem not to be shown in the Library module. And when I subsequently export to Flickr, Flickr is also showing the original photo, not the adapted one.
    I noticed this the first time after making Blacks a bit deeper, causing a sunflower to become a deeper yellow. I thought that my adaptations were not applied in the Library module. After I checked with cranking down the Saturation all the way back (to almost black-and-white), that adaptation WAS applied in the Library view. So it had to be something else, causing the same color difference between the Library and Development modules.
    When I switch from the Library module to the Development module, I see a slight delay in applying my changes, but they are applied. Before they are applied, I can see that the original photo is shown and that looks the same as in the Library module and on Flickr.
    The photostrip on the bottom of the Lightroom screen also shows the original photos only, unless I go to the development module and select a photo (adaptations are applied in the photostrip after I select the photo, not before).
    After I played a bit more in the Development module, I found something strange in the Camera Calibration menu of the Development module. The Adobe Profile (my default) caused an obvious color difference between the Library (less saturated) and the Development (more saturated) modules. The Camera Standard profile also showed a (very) slight difference, but I was unable to notice the differences using the other profiles.
    So I was thinking (but it's only a guess), that the profiles are not applied in the Library view and on export, but they are in the Development module?
    I use Lightroom 5.6, Camera RAW 8.6.
    Please help me, as this is very annoying. I currently cannot export my photos to Flickr or anywhere else, unless I overcompensate before exporting. And I really don't want to do that. My Lightroom photo is my perfect photo, and I want to keep it that way...
    Many thanks in advance for any help,
    Peter

    Hi ssprengel,
    Thanks for your reply. Let me react to each possibility you mention and provide some extra information.
    - "Check your Export / File Settings / Image Format and make sure they are set to JPG not Original". Done that, it's not on Original, but on jpg. This would not explain why I see the difference in the Library and Development modules, by the way. But better to know for sure.
    - "...the most likely thing that is wrong is your color-management on your computer is not working properly". It is a PC with Windows 7. I have been using Lightroom for maybe 6 years and I never had this problem before. The last time I changed my setup is more than a year ago and this problem only started to happen a short while ago (after the update to Lightroom 5.6? I'm not sure, but that's the only thing that has changed lately). I use a Spider to create a custom profile that is correct for my setup and do a regular update on the profile.
    - "what brand and model of monitor do you have?" I have an EIZO FlexScan S2411W and use that for a long time as well. I chose this brand of monitors for its good color reproduction and I have been happy with it for years now.
    What I am not getting is why would all this show a difference between the Library and Development module? The only difference is the Lightroom software that is switching from one module to another, and that should deliver the same photo. I'm also stating in my first post that the differences are very noticeable using the Adobe Standard Camera Profile in the Development module. I have a feeling that the profile is part of the problem.

  • HELP! Downloaded LR5 and when open it shows an error message saying error while trying to change from modules and I can not even import photos. Am I doing something wrong?

    HELP! Downloaded LR5 and when open it shows an error message saying error while trying to change from modules and I can not even import photos. Am I doing something wrong?

    I have the same problem, and the solutions in   Error changing modules | Lightroom do not work.  Even uninstalling and reinstalling a new copy did not solve the problem.  As anyone got an idea what other lingering files might be causing the problem?

  • I have LR 5.  When I'm in the book module and select the option to "Send Book to Blurb" i get an error message saying "The file does not have a program associated with it...."  How do I fix this?

    I have LR 5.  When I'm in the book module and select the option to "Send Book to Blurb" i get an error message saying "The file does not have a program associated with it for performing this action.  Please install a program, or if one is already installed, create an association in the Default Programs control panel."
    How do I fix this?

    Try the following user tip:
    "There is a problem with this Windows Installer package ..." error messages when installing iTunes for Windows

Maybe you are looking for